Ottimizzazione delle reti di distribuzione idrica tramite algoritmi genetici multi-obiettivo

Water distribution networks optimization is a challenging problem due to the dimension and the complexity of these systems. Since the last half of the twentieth century this field has been investigated by many authors. Recently, to overcome discrete nature of variables and non linearity of equations, the research has been focused on the development of heuristic algorithms. This algorithms do not require continuity and linearity of the problem functions because they are linked to an external hydraulic simulator that solve equations of mass continuity and of energy conservation of the network. In this work, a NSGA-II (Non-dominating Sorting Genetic Algorithm) has been used. This is a heuristic multi-objective genetic algorithm based on the analogy of evolution in nature. Starting from an initial random set of solutions, called population, it evolves them towards a front of solutions that minimize, separately and contemporaneously, all the objectives. This can be very useful in practical problems where multiple and discordant goals are common. Usually, one of the main drawback of these algorithms is related to time consuming: being a stochastic research, a lot of solutions must be analized before good ones are found. Results of this thesis about the classical optimal design problem shows that is possible to improve results modifying the mathematical definition of objective functions and the survival criterion, inserting good solutions created by a Cellular Automata and using rules created by classifier algorithm (C4.5). This part has been tested using the version of NSGA-II supplied by Centre for Water Systems (University of Exeter, UK) in MATLAB® environment. Even if orientating the research can constrain the algorithm with the risk of not finding the optimal set of solutions, it can greatly improve the results. Subsequently, thanks to CINECA help, a version of NSGA-II has been implemented in C language and parallelized: results about the global parallelization show the speed up, while results about the island parallelization show that communication among islands can improve the optimization. Finally, some tests about the optimization of pump scheduling have been carried out. In this case, good results are found for a small network, while the solutions of a big problem are affected by the lack of constraints on the number of pump switches. Possible future research is about the insertion of further constraints and the evolution guide. In the end, the optimization of water distribution systems is still far from a definitive solution, but the improvement in this field can be very useful in reducing the solutions cost of practical problems, where the high number of variables makes their management very difficult from human point of view.

Application of PZT and FBG impedance sensors for structural health monitoring of reinforced concrete beams strengthened with FRP composite materials

Esta Tesis tiene como objetivo principal el desarrollo de métodos de identificación del daño que sean robustos y fiables, enfocados a sistemas estructurales experimentales, fundamentalmente a las estructuras de hormigón armado reforzadas externamente con bandas fibras de polímeros reforzados (FRP). El modo de fallo de este tipo de sistema estructural es crítico, pues generalmente es debido a un despegue repentino y frágil de la banda del refuerzo FRP originado en grietas intermedias causadas por la flexión. La detección de este despegue en su fase inicial es fundamental para prevenir fallos futuros, que pueden ser catastróficos. Inicialmente, se lleva a cabo una revisión del método de la Impedancia Electro-Mecánica (EMI), de cara a exponer sus capacidades para la detección de daño. Una vez la tecnología apropiada es seleccionada, lo que incluye un analizador de impedancias así como novedosos sensores PZT para monitorización inteligente, se ha diseñado un procedimiento automático basado en los registros de impedancias de distintas estructuras de laboratorio. Basándonos en el hecho de que las mediciones de impedancias son posibles gracias a una colocación adecuada de una red de sensores PZT, la estimación de la presencia de daño se realiza analizando los resultados de distintos indicadores de daño obtenidos de la literatura. Para que este proceso sea automático y que no sean necesarios conocimientos previos sobre el método EMI para realizar un experimento, se ha diseñado e implementado un Interfaz Gráfico de Usuario, transformando la medición de impedancias en un proceso fácil e intuitivo. Se evalúa entonces el daño a través de los correspondientes índices de daño, intentando estimar no sólo su severidad, sino también su localización aproximada. El desarrollo de estos experimentos en cualquier estructura genera grandes cantidades de datos que han de ser procesados, y algunas veces los índices de daño no son suficientes para una evaluación completa de la integridad de una estructura. En la mayoría de los casos se pueden encontrar patrones de daño en los datos, pero no se tiene información a priori del estado de la estructura. En este punto, se ha hecho una importante investigación en técnicas de reconocimiento de patrones particularmente en aprendizaje no supervisado, encontrando aplicaciones interesantes en el campo de la medicina. De ahí surge una idea creativa e innovadora: detectar y seguir la evolución del daño en distintas estructuras como si se tratase de un cáncer propagándose por el cuerpo humano. En ese sentido, las lecturas de impedancias se emplean como información intrínseca de la salud de la propia estructura, de forma que se pueden aplicar las mismas técnicas que las empleadas en la investigación del cáncer. En este caso, se ha aplicado un algoritmo de clasificación jerárquica dado que ilustra además la clasificación de los datos de forma gráfica, incluyendo información cualitativa y cuantitativa sobre el daño. Se ha investigado la efectividad de este procedimiento a través de tres estructuras de laboratorio, como son una viga de aluminio, una unión atornillada de aluminio y un bloque de hormigón reforzado con FRP. La primera ayuda a mostrar la efectividad del método en sencillos escenarios de daño simple y múltiple, de forma que las conclusiones extraídas se aplican sobre los otros dos, diseñados para simular condiciones de despegue en distintas estructuras. Demostrada la efectividad del método de clasificación jerárquica de lecturas de impedancias, se aplica el procedimiento sobre las estructuras de hormigón armado reforzadas con bandas de FRP objeto de esta tesis, detectando y clasificando cada estado de daño. Finalmente, y como alternativa al anterior procedimiento, se propone un método para la monitorización continua de la interfase FRP-Hormigón, a través de una red de sensores FBG permanentemente instalados en dicha interfase. De esta forma, se obtienen medidas de deformación de la interfase en condiciones de carga continua, para ser implementadas en un modelo de optimización multiobjetivo, cuya solución se haya por medio de una expansión multiobjetivo del método Particle Swarm Optimization (PSO). La fiabilidad de este último método de detección se investiga a través de sendos ejemplos tanto numéricos como experimentales. ABSTRACT This thesis aims to develop robust and reliable damage identification methods focused on experimental structural systems, in particular Reinforced Concrete (RC) structures externally strengthened with Fiber Reinforced Polymers (FRP) strips. The failure mode of this type of structural system is critical, since it is usually due to sudden and brittle debonding of the FRP reinforcement originating from intermediate flexural cracks. Detection of the debonding in its initial stage is essential thus to prevent future failure, which might be catastrophic. Initially, a revision of the Electro-Mechanical Impedance (EMI) method is carried out, in order to expose its capabilities for local damage detection. Once the appropriate technology is selected, which includes impedance analyzer as well as novel PZT sensors for smart monitoring, an automated procedure has been design based on the impedance signatures of several lab-scale structures. On the basis that capturing impedance measurements is possible thanks to an adequately deployed PZT sensor network, the estimation of damage presence is done by analyzing the results of different damage indices obtained from the literature. In order to make this process automatic so that it is not necessary a priori knowledge of the EMI method to carry out an experimental test, a Graphical User Interface has been designed, turning the impedance measurements into an easy and intuitive procedure. Damage is then assessed through the analysis of the corresponding damage indices, trying to estimate not only the damage severity, but also its approximate location. The development of these tests on any kind of structure generates large amounts of data to be processed, and sometimes the information provided by damage indices is not enough to achieve a complete analysis of the structural health condition. In most of the cases, some damage patterns can be found in the data, but none a priori knowledge of the health condition is given for any structure. At this point, an important research on pattern recognition techniques has been carried out, particularly on unsupervised learning techniques, finding interesting applications in the medicine field. From this investigation, a creative and innovative idea arose: to detect and track the evolution of damage in different structures, as if it were a cancer propagating through a human body. In that sense, the impedance signatures are used to give intrinsic information of the health condition of the structure, so that the same clustering algorithms applied in the cancer research can be applied to the problem addressed in this dissertation. Hierarchical clustering is then applied since it also provides a graphical display of the clustered data, including quantitative and qualitative information about damage. The performance of this approach is firstly investigated using three lab-scale structures, such as a simple aluminium beam, a bolt-jointed aluminium beam and an FRP-strengthened concrete specimen. The first one shows the performance of the method on simple single and multiple damage scenarios, so that the first conclusions can be extracted and applied to the other two experimental tests, which are designed to simulate a debonding condition on different structures. Once the performance of the impedance-based hierarchical clustering method is proven to be successful, it is then applied to the structural system studied in this dissertation, the RC structures externally strengthened with FRP strips, where the debonding failure in the interface between the FRP and the concrete is successfully detected and classified, proving thus the feasibility of this method. Finally, as an alternative to the previous approach, a continuous monitoring procedure of the FRP-Concrete interface is proposed, based on an FBGsensors Network permanently deployed within that interface. In this way, strain measurements can be obtained under controlled loading conditions, and then they are used in order to implement a multi-objective model updating method solved by a multi-objective expansion of the Particle Swarm Optimization (PSO) method. The feasibility of this last proposal is investigated and successfully proven on both numerical and experimental RC beams strengthened with FRP.

Estimación de la resistencia de estructuras de hormigón armado reforzadas a cortante mediante FRP

El empleo de refuerzos de FRP en vigas de hormigón armado es cada vez más frecuente por sus numerosas ventajas frente a otros métodos más tradicionales. Durante los últimos años, la técnica FRP-NSM, consistente en introducir barras de FRP sobre el recubrimiento de una viga de hormigón, se ha posicionado como uno de los mejores métodos de refuerzo y rehabilitación de estructuras de hormigón armado, tanto por su facilidad de montaje y mantenimiento, como por su rendimiento para aumentar la capacidad resistente de dichas estructuras. Si bien el refuerzo a flexión ha sido ampliamente desarrollado y estudiado hasta la fecha, no sucede lo mismo con el refuerzo a cortante, debido principalmente a su gran complejidad. Sin embargo, se debería dedicar más estudio a este tipo de refuerzo si se pretenden conservar los criterios de diseño en estructuras de hormigón armado, los cuales están basados en evitar el fallo a cortante por sus consecuencias catastróficas Esta ausencia de información y de normativa es la que justifica esta tesis doctoral. En este pro-yecto se van a desarrollar dos metodologías alternativas, que permiten estimar la capacidad resistente de vigas de hormigón armado, reforzadas a cortante mediante la técnica FRP-NSM. El primer método aplicado consiste en la implementación de una red neuronal artificial capaz de predecir adecuadamente la resistencia a cortante de vigas reforzadas con este método a partir de experimentos anteriores. Asimismo, a partir de la red se han llevado a cabo algunos estudios a fin de comprender mejor la influencia real de algunos parámetros de la viga y del refuerzo sobre la resistencia a cortante con el propósito de lograr diseños más seguros de este tipo de refuerzo. Una configuración óptima de la red requiere discriminar adecuadamente de entre los numerosos parámetros (geométricos y de material) que pueden influir en el compor-tamiento resistente de la viga, para lo cual se han llevado a cabo diversos estudios y pruebas. Mediante el segundo método, se desarrolla una ecuación de proyecto que permite, de forma sencilla, estimar la capacidad de vigas reforzadas a cortante con FRP-NSM, la cual podría ser propuesta para las principales guías de diseño. Para alcanzar este objetivo, se plantea un pro-blema de optimización multiobjetivo a partir de resultados de ensayos experimentales llevados a cabo sobre vigas de hormigón armado con y sin refuerzo de FRP. El problema multiobjetivo se resuelve mediante algoritmos genéticos, en concreto el algoritmo NSGA-II, por ser más apropiado para problemas con varias funciones objetivo que los métodos de optimización clásicos. Mediante una comparativa de las predicciones realizadas con ambos métodos y de los resulta-dos de ensayos experimentales se podrán establecer las ventajas e inconvenientes derivadas de la aplicación de cada una de las dos metodologías. Asimismo, se llevará a cabo un análisis paramétrico con ambos enfoques a fin de intentar determinar la sensibilidad de aquellos pa-rámetros más sensibles a este tipo de refuerzo. Finalmente, se realizará un análisis estadístico de la fiabilidad de las ecuaciones de diseño deri-vadas de la optimización multiobjetivo. Con dicho análisis se puede estimar la capacidad resis-tente de una viga reforzada a cortante con FRP-NSM dentro de un margen de seguridad espe-cificado a priori. ABSTRACT The use of externally bonded (EB) fibre-reinforced polymer (FRP) composites has gained acceptance during the last two decades in the construction engineering community, particularly in the rehabilitation of reinforced concrete (RC) structures. Currently, to increase the shear resistance of RC beams, FRP sheets are externally bonded (EB-FRP) and applied on the external side surface of the beams to be strengthened with different configurations. Of more recent application, the near-surface mounted FRP bar (NSM-FRP) method is another technique successfully used to increase the shear resistance of RC beams. In the NSM method, FRP rods are embedded into grooves intentionally prepared in the concrete cover of the side faces of RC beams. While flexural strengthening has been widely developed and studied so far, the same doesn´t occur to shearing strength mainly due to its great complexity. Nevertheless, if design criteria are to be preserved more research should be done to this sort of strength, which are based on avoiding shear failure and its catastrophic consequences. However, in spite of this, accurately calculating the shear capacity of FRP shear strengthened RC beams remains a complex challenge that has not yet been fully resolved due to the numerous variables involved in the procedure. The objective of this Thesis is to develop methodologies to evaluate the capacity of FRP shear strengthened RC beams by dealing with the problem from a different point of view to the numerical modeling approach by using artificial intelligence techniques. With this purpose two different approaches have been developed: one concerned with the use of artificial neural networks and the other based on the implementation of an optimization approach developed jointly with the use of artificial neural networks (ANNs) and solved with genetic algorithms (GAs). With these approaches some of the difficulties concerned regarding the numerical modeling can be overcome. As an alternative tool to conventional numerical techniques, neural networks do not provide closed form solutions for modeling problems but do, however, offer a complex and accurate solution based on a representative set of historical examples of the relationship. Furthermore, they can adapt solutions over time to include new data. On the other hand, as a second proposal, an optimization approach has also been developed to implement simple yet accurate shear design equations for this kind of strengthening. This approach is developed in a multi-objective framework by considering experimental results of RC beams with and without NSM-FRP. Furthermore, the results obtained with the previous scheme based on ANNs are also used as a filter to choose the parameters to include in the design equations. Genetic algorithms are used to solve the optimization problem since they are especially suitable for solving multi-objective problems when compared to standard optimization methods. The key features of the two proposed procedures are outlined and their performance in predicting the capacity of NSM-FRP shear strengthened RC beams is evaluated by comparison with results from experimental tests and with predictions obtained using a simplified numerical model. A sensitivity study of the predictions of both models for the input parameters is also carried out.

Diseño para fabricación digital: definición unívoca entre forma y fabricación en arquitectura

La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. Establecida la primera conclusión, el capítulo de contexto histórico continúa enfocándose sobre la aplicación de las técnicas digitales en el Proceso de proyecto primero, y en la puesta en obra después. Los casos de estudio identifican claramente como un punto de inflexión para la generación de formas complejas mediante un software CAD el Museo Guggenheim de Bilbao en 1992. El motivo esencial para elegir este proyecto como el primer proyecto digital es el uso de la herramienta de definición digital de la geometría para su reproducción inequívoca en obra. “La revolución digital ha aportado al Arquitecto la posibilidad de abandonar las tipologías arquitectónicas basados en restricciones geométricas-constructivas. La aplicación de técnicas de fabricación digital ha permitido la capacidad de diseñar con independencia del sistema constructivo y libertad formal. En este nuevo contexto las prestaciones suponen los nuevos límites conceptuales, ya que el acceso y disposición de la información del comportamiento de las alternativas que cada geometría conlleva demanda del Arquitecto la jerarquización de los objetivos y la formulación en un conjunto coherente de parámetros”. Los proyectos que emplean herramientas digitales para la resolución de las distintas etapas del proceso proyectual se verán incrementados de forma exponencial desde 1992 hasta nuestros días. A pesar del importante auge de las técnicas de diseño asistido por ordenador el principal desafío sigue siendo la vinculación de las geometrías y materiales propuestos con las capacidades de las técnicas de manufactura y puesta en obra. El proceso de diseño para fabricación en un entorno digital es una tecnología madura en otras industrias como la aeroespacial o la automovilística, incluso la de productos de consumo y decoración, sin embargo en el sector de Construcción es un sistema inmaduro e inconexo. Las particularidades de la industria de la construcción aún no han sido abordadas en su totalidad y las propuestas de investigación realizadas en este ámbito se han centrado hasta 2015 en partes del proceso y no en el proceso total. “El principal obstáculo para la estandarización e implantación globalizada de un proceso digital desde el origen de la forma hasta la construcción es la inexistencia de un protocolo integrado que integre las limitaciones de fabricación, económicas y de puesta en obra junto a la evaluación de desempeño prestacional durante la fases iniciales de proyecto”. En el capítulo número 3 se estudian los distintos procesos de generación de la forma. Se propone una definición específica para el ámbito de la investigación de “forma” en el entendemos que se incluye la envolvente exterior y el conjunto organizativo de espacios interiores conectados. Por lo tanto no es excluyente del interior. El objetivo de este estudio es analizar y clasificar los procesos para la generación digital de formas en los distintos proyectos seleccionados como emblemáticos de cada tipología. Se concluye que la aproximación a este proceso es muy variada y compleja, con aplicación segregada y descoordinada entre los distintos agentes que han intervenir. En un proceso de generación formal analógico los parámetros que intervienen son en parte conscientes y en parte inconscientes o aprendidos. El Arquitecto sólo tiene control sobre la parte consciente de los parámetros a integrar en el diseño, de acuerdo a sus conocimientos y capacidades será capaz de manejar un número limitado de parámetros. La parte aprendida permanece en el inconsciente y dirige el proceso analógico, aportando prejuicios estéticos incorporados durante el proceso formativo y propio del entorno cultural. “El empleo de herramientas digitales basadas en la evaluación prestacional durante el proceso de selección formal permite al Arquitecto conocer “en tiempo real” el desempeño en el conjunto de prestaciones evaluadoras del conjunto de alternativas geométricas a la propuesta previamente definida por la intuición arquitectónica. El proceso definido no persigue identificar una solución óptima sino asistir al Arquitecto en el proceso de generación de la forma mediante la evaluación continua de los vectores direccionales más idóneos que el procedimiento generativo plantea”. La definición de complejidad en generación y producción de formas en relación con el proceso de diseño digital paramétrico global o integrado, es esencial para establecer un protocolo que optimice su gestión. “Se propone como definición de complejidad como factor resultante de multiplicar el número de agentes intervinientes por el número de parámetros e interacciones comunes que intervienen en el proceso de generación de la forma, dividido por la complejidad de intercambio de información digital desde el origen hasta la fase de fabricación y construcción”. Una vez analizados los procesos de generación digital de Arquitectura se propone identificar los parámetros geométricos que definen el proceso de Diseño digital, entendiendose por Diseño el proceso que engloba desde la proposición de una forma inicial basada en la intuición del Arquitecto, la generación y evaluación de variantes y posterior definición digital para producción, tanto de un objeto, un sistema o de la totalidad del Proyecto. En la actualidad el proceso de Diseño es discontinuo y lineal organizandose los parámetros por disciplinas en las que está estructurada las atribuciones profesionales en la industria de la construcción. Para simplificar la identificación y listado se han agrupado siguiendo estos grupos de conocimiento. Entendemos parametros invariables aquellos que son independientes de Tipologías arquitectónicas o que dependen del mismo proceso de generación de la Forma. “El listado de los parámetros que intervienen en un proceso de generación formal es una abstracción de una realidad compleja. La parametrización de las decisiones que intervienen en la selección de una forma determinada mediante “well defined problems” es imposible. El proceso que esta tesis describe entiende esta condición como un elemento que pone en valor el propio procedimiento generativo por la riqueza que la subjetividad que el equipo de diseño aporta”. La segunda parte esencial de esta investigación pretende extraer las restricciones propias del estado del arte de la fabricación digital para posteriormente incorporarlos en los procesos digitales de definición de la Forma arquitectónica. “La integración de las restricciones derivadas de las técnicas de fabricación y construcción digitales en el proceso de generación de formas desde el ámbito de la Arquitectura debe referirse a los condicionantes geométricos asociados a cada sistema constructivo, material y técnica de fabricación. La geometría es además el vínculo que permite asociar el conjunto de parámetros prestacionales seleccionados para un Proyecto con los sistemas de fabricación digital”. A estos condicionantes geométricos obtenidos del análisis de cada sistema de fabricación digital se les ha denominado “invariantes geométricos”. Bajo este término se engloban tanto límites dimensionales de fabricación, como materiales compatibles, tolerancias de manufactura e instalación y cualidades prestacionales asociadas. El objetivo de esta propuesta es emplear la geometría, herramienta fundamental y propia del Arquitecto, como nexo de unión entre el conjunto complejo y heterogéneo de parámetros previamente listados y analizados. Para ello se han simplificado en tablas específicas para cada parámetro prestacional los condicionantes geométricos que se derivan de los Sistemas de fabricación digital compatibles (ver apéndice 1). El estudio y evaluación de las capacidades y objetivos de las distintas plataformas de software disponibles y de las experiencias profesionales evaluadas en los proyectos presentados, permiten concluir que la propuesta de plataforma digital de diseño integral multi-paramétrico de formas arquitectónicas requiere de un protocolo de interoperatibilidad específico aún no universalmente establecido. Actualmente el enfoque de la estrategia para normalizar y universalizar el contexto normativo para regular la interoperatibilidad se centra en figura del gestor denominado “BIM manager”. Las atribuciones y roles de esta figura se enfocan a la gestión del continente y no del contenido (Definición de los formatos de intercambio, niveles de desarrollo (LOD) de los componentes o conjuntos constructivos, detección de interferencias y documentación del propio modelo). Siendo este ámbito un desarrollo necesario para la propuesta de universalización del sistema de diseño para fabricación digital integrado, la presente investigación aporta un organigrama y protocolo asociado. El protocolo: 1. Establece la responsabilidad de identificar y definir la Información que debe determinar el proceso de generación y desarrollo de la forma arquitectónica. 2. Define la forma digital apropiada para generar la geometría del Proyecto, incluyendo la precisión necesaria para cada componente y el nivel de detalle necesario para su exportación inequívoca al proceso de fabricación. 3. Define el tempo de cada etapa de diseño identificando un nivel de detalle acorde. 4. Acopla este organigrama dentro de las estructuras nuevas que se proponen en un entorno BIM para asegurar que no se producen solapes o vacíos con las atribuciones que se identifican para el BIM Manager. “El Arquitecto debe dirigir el protocolo de generación coordinada con los sistemas de producción digital para conseguir que la integración completa. El protocolo debe asistir al proceso de generación de forma mediante la evaluación del desempeño prestacional de cada variante en tiempo real. La comunicación entre herramientas digitales es esencial para permitir una ágil transmisión de información. Es necesario establecer un protocolo adaptado a los objetivos y las necesidades operativas de cada proyecto ya que la estandarización de un protocolo único no es posible”. Una decisión estratégica a la hora de planificar una plataforma de diseño digital común es establecer si vamos a optar por un Modelo digital único o diversos Modelos digitales federados. Cada uno de los modos de trabajo tiene fortalezas y debilidades, no obstante en el ámbito de investigación se ha concluido que un proceso integrado de Diseño que incorpore la evaluación prestacional y conceptual definida en el Capítulo 3, requiere necesariamente de varios modelos de software distintos que han de relacionarse entre sí mediante un protocolo de comunicación automatizado. Una plataforma basada en un modelo federado consiste en establecer un protocolo de comunicación entre los programas informáticos empleados por cada disciplina. En este modelo de operación cada equipo de diseño debe establecer las bases de comunicación en función del número y tipo de programas y procesos digitales a emplear. En esta investigación se propone un protocolo basado en los estándares de intercambio de información que estructura cualquier proceso de generación de forma paramétrico “La investigación establece el empleo de algoritmos evolutivos como el sistema actual óptimo para desarrollar un proceso de generación de formas basadas en la integración y coordinación de invariantes geométricos derivados de un conjunto de objetivos prestacionales y constructivos. No obstante, para la aplicación en el caso práctico realizado se ha podido verificar que la evaluación del desempeño aún no puede realizarse en una única herramienta y por lo tanto el proceso de selección de las variantes genéticas óptimas ha de ejecutarse de forma manual y acumulativa. El proceso debe realizarse de manera federada para la selección evolutiva de los invariantes geométricos dimensionales”. La evaluación del protocolo de integración y los condicionantes geométricos obtenidos como parámetros geométricos que controlan las posibles formas compatibles se realiza mediante su aplicación en un caso práctico. El ejercicio simula la colaboración multidisciplinar con modelos federados de plataformas distintas. La elección del tamaño y complejidad constructiva del proyecto se ha modulado para poder alcanzar un desarrollo completo de cada uno de los parámetros prestacionales seleccionados. Continuando con el mismo objetivo propuesto para los parámetros prestacionales, la tipología constructiva-estructural seleccionada para el ejercicio permite la aplicación la totalidad de invariantes geométricos asociados. El objetivo de este caso práctico es evaluar la capacidad alterar la forma inicialmente propuesta mediante la evaluación del desempeño prestacional de conjunto de variantes geométricas generadas a partir de un parámetro dimensional determinado. Para que este proceso tenga sentido, cada una de las variantes debe ser previamente validada conforme a las limitaciones geométricas propias de cada sistema de fabricación y montaje previstos. El interés de las conclusiones obtenidas es la identificación de una variante geométrica distante a la solución simétrica inicialmente como la solución óptima para el conjunto de parámetros seleccionados. Al tiempo se ha comprobado como la participación de un conjunto de parámetros multi-disciplinares que representan la realidad compleja de los objetivos arquitectónicos favorecen la aparición de variaciones genéticas con prestaciones mejoradas a la intuición inicial. “La herencias tipológicas suponen un límite para la imaginación de variantes formales al proceso de ideación arquitectónica. El ejercicio realizado demuestra que incluso en casos donde aparentemente la solución óptima aparenta ser obvia una variante aleatoria puede mejorar su desempeño global. La posibilidad de conocer las condiciones geométricas de las técnicas de fabricación digital compatibles con el conjunto de parámetros seleccionados por el Arquitecto para dirigir el proceso asegura que los resultados del algoritmo evolutivo empleado sean constructivamente viables. La mejora de imaginación humana con la aportación de geometrías realmente construibles supone el objetivo último de esta tesis”. ABSTRACT Architectural form generation process is shifting from analogical to digital. Digital technology has changed the way we design empowering Architects and Engineers to precisely define any complex geometry envisioned. At the same time, the construction industry, following aeronautical and automotive industries, is implementing digital manufacturing techniques to improve efficiency and quality. Consequently construction complexity will no longer be related to geometry complexity and it is associated to coordination with digital manufacturing capacities. Unfortunately it is agreed that non-standard geometries, even when proposed with performance optimization criteria, are only suitable for projects with non-restricted budgets. Furthemore, the lack of coordinated exportation protocol and geometry management between design and construction is avoiding the globalization of emergence process in built projects Present research first objective is to identify exclusive form-generation parameters related to digital manufacturing geometrical restraints. The intention was to use geometry as the form-generation tool and integrate the digital manufacturing capacities at first stages of the project. The first chapter of this text describes the investigation historical context focusing on the influence between accurate geometry definition at non-standard forms and its construction. At first examples of non-Euclidean geometries built the communication between design and construction were based on analogical partial and imprecise documentation. Deficient communication leads to geometry adaptation on site leaving the final form uncontrolled by the Architect. Computer Aided Design enable Architects to define univocally complex geometries that previously where impossible to communicate. “The univocally definition of the Form, and communication between design and construction is essential for complex geometry Projects”. The second chapter is focused on digital technologies application in form finding process and site construction. The case studies selected identifies a clear inflexion node at 1992 with the Guggenheim Museum in Bilbao. The singularity of this project was the use of Aeronautics software to define digitally the external envelope complex geometry to enable the contractor to build it. “The digital revolution has given the Architect the capacity to design buildings beyond the architectural archetypes driven by geometric-constructive limitations. The application of digital manufacturing techniques has enabled a free-form construction without geometrical limitations. In this new context performance shall be the responsible to set new conceptual boundaries, since the behavior of each possible geometry can be compare and analyze beforehand. The role of the Architect is to prioritize the performance and architectural objectives of each project in a complete and coherent set of parameters”. Projects using digital tools for solving various stages of the design process were increased exponentially since 1992 until today. Despite the significant rise of the techniques of computer-aided design the main challenge remains linking geometries and materials proposed at each design with the capabilities of digital manufacturing techniques. Design for manufacturing in a digital environment is a mature technology in other industries such as aerospace and automotive, including consumer products and decoration, but in the construction sector is an immature and disjointed system. The peculiarities of the construction industry have not yet been addressed in its entirety and research proposals made in this area until 2015 have focused in separate parts of the process and not the total process. “The main obstacle to global standardization and implementation of a complete digital process from the form-finding to construction site is the lack of an integrated protocol that integrates manufacturing, economic and commissioning limitations, together with the performance evaluation of each possible form”. The different form generation processes are studied at chapter number 3. At the introduction of this chapter there is a specific definition of "form" for the research field. Form is identified with the outer envelope geometry, including the organizational set of connected indoor spaces connected to it. Therefore it is not exclusive of the interior. The aim of this study is to analyze and classify the main digital form generation processes using different selected projects as emblematic of each type. The approach to this process is complex, with segregated and uncoordinated different actors have to intervene application. In an analogical form-generation process parameters involved are partly conscious and partly unconscious or learned. The architect has control only over limited part of the parameters to be integrated into the design, according to their knowledge and. There is also a learned aesthetical prejudice that leads the form generation process to a specific geometry leaving the performance and optimization criteria apart from the decision making process. “Using performance evaluation digital tools during form finding process provides real-time comparative information to the Architect enabling geometry selection based on its performance. The generative form generation process described at this document does not ambition to identify the optimum geometry for each set of parameters. The objective is to provide quick information at each generation of what direction is most favorable for the performance parameters selected”. Manufacturing complexity definition in relation to a global and integral process of digital design for manufacture is essential for establishing an efficient managing protocol. “The definition of complexity associated to design for production in Architecture is proposed as the factor between number of different agents involved in the process by the number of interactions required between them, divided by the percentage of the interchange of information that is standardized and proof of information loss”. Design in architecture is a multi-objective process by definition. Therefore, addressing generation process linked to a set of non-coherent parameters requires the selection of adequate generative algorithm and the interaction of the architect. During the second half of the twentieth century and early twenty-first century it have been developed various mathematical algorithms for multi-parametric digital design. Heuristic algorithms are the most adequate algorithms for architectural projects due to its nature. The advantage of such algorithms is the ability to efficiently handle large scale optimization cases where a large number of design objectives and variables are involved. These generative processes do not pursue the optimum solution, in fact it will be impossible to proof with such algorithm. This is not a problem in architectural design where the final goal is to guide the form finding process towards a better performance within the initial direction provided by the architect. This research has focused on genetic algorithms due to its capacity to generate geometric alternatives in multiple directions and evaluate the fitness against a set of parameters specified in a single process. "Any protocol seeks to achieve standardization. The design to manufacturing protocol aims to provide a coordinated and coherent form generation process between a set of design parameters and the geometrical requirements of manufacturing technique. The protocol also provides an information exchange environment where there is a communication path and the level of information is ensured. The research is focused on the process because it is considered that each project will have its own singularities and parameters but the process will stay the same. Again the development of a specific tool is not a goal for the research, the intention is to provide an open source protocol that is valid for any set of tools”. Once the digital generation processes are being analized and classified, the next step is to identify the geometric parameters that define the digital design process. The definition of design process is including from the initial shape proposal based on the intuition of the architect to the generation, evaluation, selection and production of alternatives, both of an object , system or of the entire project . The current design process in Architecture is discontinuous and linear, dividing the process in disciplines in which the construction industry is structured. The proposal is to unify all relevant parameters in one process. The parameters are listed in groups of knowledge for internal classification but the matrix used for parameter relationship determination are combined. “A multi-parameter determination of the form-finding process is the integration all the measurable decisions laying behind Architect intuition. It is not possible to formulate and solve with an algorithm the design in Architecture. It is not the intention to do so with the proposal of this research. The process aims to integrate in one open protocol a selection of parameters by using geometry as common language. There is no optimum solution for any step of the process, the outcome is an evaluation of performance of all the form variations to assist the Architect for the selection of the preferable solution for the project”. The research follows with the geometrical restrictions of today Digital manufacturing techniques. Once determined it has been integrated in the form-finding process. “Digital manufacturing techniques are integrated in the form-finding process using geometry as common language. Geometric restraints define the boundary for performance parametric form-finding process. Geometrical limitations are classified by material and constructive system”. Choose between one digital model or several federate models is a strategic decision at planning a digital design for manufacturing protocol. Each one of the working models have strengths and weakens, nevertheless for the research purposes federated models are required to manage the different performance evaluation software platforms. A protocol based on federated models shall establish a communication process between software platforms and consultants. The manager shall integrate each discipline requirements defining the communication basis. The proposed protocol is based on standards on information exchange with singularities of the digital manufacturing industry. “The research concludes evolutionary algorithms as current best system to develop a generative form finding process based on the integration and coordination of a set of performance and constructive objectives. However, for application in professional practice and standardize it, the performance evaluation cannot be done in only one tool and therefore the selection of optimal genetic variants must be run in several iterations with a cumulative result. Consequently, the evaluation process within the geometrical restraints shall be carried out with federated models coordinated following the information exchange protocol”. The integration protocol and geometric constraints evaluation is done by applying in a practical case study. The exercise simulates multidisciplinary collaboration across software platforms with federated models. The choice of size and construction complexity of the project has been modulated to achieve the full development of each of the parameters selected. Continuing with the same objective proposed for the performance parameters the constructive and structural type selected for the exercise allows the application all geometric invariants associated to the set of parameters selected. The main goal of the case study is to proof the capacity of the manufacturing integrated form finding process to generate geometric alternatives to initial form with performance improved and following the restrictions determined by the compatible digital manufacturing technologies. The process is to be divided in consecutive analysis each one limited by the geometrical conditions and integrated in a overall evaluation. The interest of this process is the result of a non-intuitive form that performs better than a double symmetrical form. The second conclusion is that one parameter evaluation alone will not justify the exploration of complex geometry variations, but when there is a set of parameters with multidisciplinary approach then the less obvious solution emerge as the better performing form. “Architectural typologies impose limitation for Architects capacity to imagine formal variations. The case study and the research conclusions proof that even in situations where the intuitive solution apparently is the optimum solution, random variations can perform better when integrating all parameters evaluation. The capacity of foreseing the geometrical properties linking each design parameter with compatible manufacturing technologies ensure the result of the form-finding process to be constructively viable. Finally, the propose of a complete process where the geometry alternatives are generated beyond the Architect intuition and performance evaluated by a set of parameters previously selected and coordinated with the manufacturing requirements is the final objective of the Thesis”.

New methods for the synthesis of radiation patterns of coupled antenna arrays = Nuevos métodos de síntesis de diagramas de radiación de agrupaciones de antenas acopladas

El principal objetivo de esta tesis es el desarrollo de métodos de síntesis de diagramas de radiación de agrupaciones de antenas, en donde se realiza una caracterización electromagnética rigurosa de los elementos radiantes y de los acoplos mutuos existentes. Esta caracterización no se realiza habitualmente en la gran mayoría de métodos de síntesis encontrados en la literatura, debido fundamentalmente a dos razones. Por un lado, se considera que el diagrama de radiación de un array de antenas se puede aproximar con el factor de array que únicamente tiene en cuenta la posición de los elementos y las excitaciones aplicadas a los mismos. Sin embargo, como se mostrará en esta tesis, en múltiples ocasiones un riguroso análisis de los elementos radiantes y del acoplo mutuo entre ellos es importante ya que los resultados obtenidos pueden ser notablemente diferentes. Por otro lado, no es sencillo combinar un método de análisis electromagnético con un proceso de síntesis de diagramas de radiación. Los métodos de análisis de agrupaciones de antenas suelen ser costosos computacionalmente, ya que son estructuras grandes en términos de longitudes de onda. Generalmente, un diseño de un problema electromagnético suele comprender varios análisis de la estructura, dependiendo de las variaciones de las características, lo que hace este proceso muy costoso. Dos métodos se utilizan en esta tesis para el análisis de los arrays acoplados. Ambos están basados en el método de los elementos finitos, la descomposición de dominio y el análisis modal para analizar la estructura radiante y han sido desarrollados en el grupo de investigación donde se engloba esta tesis. El primero de ellos es una técnica de análisis de arrays finitos basado en la aproximación de array infinito. Su uso es indicado para arrays planos de grandes dimensiones con elementos equiespaciados. El segundo caracteriza el array y el acoplo mutuo entre elementos a partir de una expansión en modos esféricos del campo radiado por cada uno de los elementos. Este método calcula los acoplos entre los diferentes elementos del array usando las propiedades de traslación y rotación de los modos esféricos. Es capaz de analizar agrupaciones de elementos distribuidos de forma arbitraria. Ambas técnicas utilizan una formulación matricial que caracteriza de forma rigurosa el campo radiado por el array. Esto las hace muy apropiadas para su posterior uso en una herramienta de diseño, como los métodos de síntesis desarrollados en esta tesis. Los resultados obtenidos por estas técnicas de síntesis, que incluyen métodos rigurosos de análisis, son consecuentemente más precisos. La síntesis de arrays consiste en modificar uno o varios parámetros de las agrupaciones de antenas buscando unas determinadas especificaciones de las características de radiación. Los parámetros utilizados como variables de optimización pueden ser varios. Los más utilizados son las excitaciones aplicadas a los elementos, pero también es posible modificar otros parámetros de diseño como son las posiciones de los elementos o las rotaciones de estos. Los objetivos de las síntesis pueden ser dirigir el haz o haces en una determinada dirección o conformar el haz con formas arbitrarias. Además, es posible minimizar el nivel de los lóbulos secundarios o del rizado en las regiones deseadas, imponer nulos que evitan posibles interferencias o reducir el nivel de la componente contrapolar. El método para el análisis de arrays finitos basado en la aproximación de array infinito considera un array finito como un array infinito con un número finito de elementos excitados. Los elementos no excitados están físicamente presentes y pueden presentar tres diferentes terminaciones, corto-circuito, circuito abierto y adaptados. Cada una de estas terminaciones simulará mejor el entorno real en el que el array se encuentre. Este método de análisis se integra en la tesis con dos métodos diferentes de síntesis de diagramas de radiación. En el primero de ellos se presenta un método basado en programación lineal en donde es posible dirigir el haz o haces, en la dirección deseada, además de ejercer un control sobre los lóbulos secundarios o imponer nulos. Este método es muy eficiente y obtiene soluciones óptimas. El mismo método de análisis es también aplicado a un método de conformación de haz, en donde un problema originalmente no convexo (y de difícil solución) es transformado en un problema convexo imponiendo restricciones de simetría, resolviendo de este modo eficientemente un problema complejo. Con este método es posible diseñar diagramas de radiación con haces de forma arbitraria, ejerciendo un control en el rizado del lóbulo principal, así como en el nivel de los lóbulos secundarios. El método de análisis de arrays basado en la expansión en modos esféricos se integra en la tesis con tres técnicas de síntesis de diagramas de radiación. Se propone inicialmente una síntesis de conformación del haz basado en el método de la recuperación de fase resuelta de forma iterativa mediante métodos convexos, en donde relajando las restricciones del problema original se consiguen unas soluciones cercanas a las óptimas de manera eficiente. Dos métodos de síntesis se han propuesto, donde las variables de optimización son las posiciones y las rotaciones de los elementos respectivamente. Se define una función de coste basada en la intensidad de radiación, la cual es minimizada de forma iterativa con el método del gradiente. Ambos métodos reducen el nivel de los lóbulos secundarios minimizando una función de coste. El gradiente de la función de coste es obtenido en términos de la variable de optimización en cada método. Esta función de coste está formada por la expresión rigurosa de la intensidad de radiación y por una función de peso definida por el usuario para imponer prioridades sobre las diferentes regiones de radiación, si así se desea. Por último, se presenta un método en el cual, mediante técnicas de programación entera, se buscan las fases discretas que generan un diagrama de radiación lo más cercano posible al deseado. Con este método se obtienen diseños que minimizan el coste de fabricación. En cada uno de las diferentes técnicas propuestas en la tesis, se presentan resultados con elementos reales que muestran las capacidades y posibilidades que los métodos ofrecen. Se comparan los resultados con otros métodos disponibles en la literatura. Se muestra la importancia de tener en cuenta los diagramas de los elementos reales y los acoplos mutuos en el proceso de síntesis y se comparan los resultados obtenidos con herramientas de software comerciales. ABSTRACT The main objective of this thesis is the development of optimization methods for the radiation pattern synthesis of array antennas in which a rigorous electromagnetic characterization of the radiators and the mutual coupling between them is performed. The electromagnetic characterization is usually overlooked in most of the available synthesis methods in the literature, this is mainly due to two reasons. On the one hand, it is argued that the radiation pattern of an array is mainly influenced by the array factor and that the mutual coupling plays a minor role. As it is shown in this thesis, the mutual coupling and the rigorous characterization of the array antenna influences significantly in the array performance and its computation leads to differences in the results obtained. On the other hand, it is difficult to introduce an analysis procedure into a synthesis technique. The analysis of array antennas is generally expensive computationally as the structure to analyze is large in terms of wavelengths. A synthesis method requires to carry out a large number of analysis, this makes the synthesis problem very expensive computationally or intractable in some cases. Two methods have been used in this thesis for the analysis of coupled antenna arrays, both of them have been developed in the research group in which this thesis is involved. They are based on the finite element method (FEM), the domain decomposition and the modal analysis. The first one obtains a finite array characterization with the results obtained from the infinite array approach. It is specially indicated for the analysis of large arrays with equispaced elements. The second one characterizes the array elements and the mutual coupling between them with a spherical wave expansion of the radiated field by each element. The mutual coupling is computed using the properties of translation and rotation of spherical waves. This method is able to analyze arrays with elements placed on an arbitrary distribution. Both techniques provide a matrix formulation that makes them very suitable for being integrated in synthesis techniques, the results obtained from these synthesis methods will be very accurate. The array synthesis stands for the modification of one or several array parameters looking for some desired specifications of the radiation pattern. The array parameters used as optimization variables are usually the excitation weights applied to the array elements, but some other array characteristics can be used as well, such as the array elements positions or rotations. The desired specifications may be to steer the beam towards any specific direction or to generate shaped beams with arbitrary geometry. Further characteristics can be handled as well, such as minimize the side lobe level in some other radiating regions, to minimize the ripple of the shaped beam, to take control over the cross-polar component or to impose nulls on the radiation pattern to avoid possible interferences from specific directions. The analysis method based on the infinite array approach considers an infinite array with a finite number of excited elements. The infinite non-excited elements are physically present and may have three different terminations, short-circuit, open circuit and match terminated. Each of this terminations is a better simulation for the real environment of the array. This method is used in this thesis for the development of two synthesis methods. In the first one, a multi-objective radiation pattern synthesis is presented, in which it is possible to steer the beam or beams in desired directions, minimizing the side lobe level and with the possibility of imposing nulls in the radiation pattern. This method is very efficient and obtains optimal solutions as it is based on convex programming. The same analysis method is used in a shaped beam technique in which an originally non-convex problem is transformed into a convex one applying symmetry restrictions, thus solving a complex problem in an efficient way. This method allows the synthesis of shaped beam radiation patterns controlling the ripple in the mainlobe and the side lobe level. The analysis method based on the spherical wave expansion is applied for different synthesis techniques of the radiation pattern of coupled arrays. A shaped beam synthesis is presented, in which a convex formulation is proposed based on the phase retrieval method. In this technique, an originally non-convex problem is solved using a relaxation and solving a convex problems iteratively. Two methods are proposed based on the gradient method. A cost function is defined involving the radiation intensity of the coupled array and a weighting function that provides more degrees of freedom to the designer. The gradient of the cost function is computed with respect to the positions in one of them and the rotations of the elements in the second one. The elements are moved or rotated iteratively following the results of the gradient. A highly non-convex problem is solved very efficiently, obtaining very good results that are dependent on the starting point. Finally, an optimization method is presented where discrete digital phases are synthesized providing a radiation pattern as close as possible to the desired one. The problem is solved using linear integer programming procedures obtaining array designs that greatly reduce the fabrication costs. Results are provided for every method showing the capabilities that the above mentioned methods offer. The results obtained are compared with available methods in the literature. The importance of introducing a rigorous analysis into the synthesis method is emphasized and the results obtained are compared with a commercial software, showing good agreement.

Constraint qualifications in convex vector semi-infinite optimization

Convex vector (or multi-objective) semi-infinite optimization deals with the simultaneous minimization of finitely many convex scalar functions subject to infinitely many convex constraints. This paper provides characterizations of the weakly efficient, efficient and properly efficient points in terms of cones involving the data and Karush–Kuhn–Tucker conditions. The latter characterizations rely on different local and global constraint qualifications. The results in this paper generalize those obtained by the same authors on linear vector semi-infinite optimization problems.

Multi-criteria logistics distribution network design using SAS/OR

This paper explores the use of the optimization procedures in SAS/OR software with application to the contemporary logistics distribution network design using an integrated multiple criteria decision making approach. Unlike the traditional optimization techniques, the proposed approach, combining analytic hierarchy process (AHP) and goal programming (GP), considers both quantitative and qualitative factors. In the integrated approach, AHP is used to determine the relative importance weightings or priorities of alternative warehouses with respect to both deliverer oriented and customer oriented criteria. Then, a GP model incorporating the constraints of system, resource, and AHP priority is formulated to select the best set of warehouses without exceeding the limited available resources. To facilitate the use of integrated multiple criteria decision making approach by SAS users, an ORMCDM code was implemented in the SAS programming language. The SAS macro developed in this paper selects the chosen variables from a SAS data file and constructs sets of linear programming models based on the selected GP model. An example is given to illustrate how one could use the code to design the logistics distribution network.

A fuzzy AHP based integer linear programming model for the multi-criteria transshipment problem

Purpose – The purpose of this research is to develop a holistic approach to maximize the customer service level while minimizing the logistics cost by using an integrated multiple criteria decision making (MCDM) method for the contemporary transshipment problem. Unlike the prevalent optimization techniques, this paper proposes an integrated approach which considers both quantitative and qualitative factors in order to maximize the benefits of service deliverers and customers under uncertain environments. Design/methodology/approach – This paper proposes a fuzzy-based integer linear programming model, based on the existing literature and validated with an example case. The model integrates the developed fuzzy modification of the analytic hierarchy process (FAHP), and solves the multi-criteria transshipment problem. Findings – This paper provides several novel insights about how to transform a company from a cost-based model to a service-dominated model by using an integrated MCDM method. It suggests that the contemporary customer-driven supply chain remains and increases its competitiveness from two aspects: optimizing the cost and providing the best service simultaneously. Research limitations/implications – This research used one illustrative industry case to exemplify the developed method. Considering the generalization of the research findings and the complexity of the transshipment service network, more cases across multiple industries are necessary to further enhance the validity of the research output. Practical implications – The paper includes implications for the evaluation and selection of transshipment service suppliers, the construction of optimal transshipment network as well as managing the network. Originality/value – The major advantages of this generic approach are that both quantitative and qualitative factors under fuzzy environment are considered simultaneously and also the viewpoints of service deliverers and customers are focused. Therefore, it is believed that it is useful and applicable for the transshipment service network design.

Multiple criteria optimization of contemporary logistics distribution network problems

In the contemporary customer-driven supply chain, maximization of customer service plays an equally important role as minimization of costs for a company to retain and increase its competitiveness. This article develops a multiple-criteria optimization approach, combining the analytic hierarchy process (AHP) and an integer linear programming (ILP) model, to aid the design of an optimal logistics distribution network. The proposed approach outperforms traditional cost-based optimization techniques because it considers both quantitative and qualitative factors and also aims at maximizing the benefits of deliverer and customers. In the approach, the AHP is used to determine the relative importance weightings or priorities of alternative warehouses with respect to some critical customer-oriented criteria. The results of AHP prioritization are utilized as the input of the ILP model, the objective of which is to select the best warehouses at the lowest possible cost. In this article, two commercial packages are used: including Expert Choice and LINDO.

Optimization of pavement maintenance and rehabilitation programming using shuffled complex evolution algorithm

The major barrier to practical optimization of pavement preservation programming has always been that for formulations where the identity of individual projects is preserved, the solution space grows exponentially with the problem size to an extent where it can become unmanageable by the traditional analytical optimization techniques within reasonable limit. This has been attributed to the problem of combinatorial explosion that is, exponential growth of the number of combinations. The relatively large number of constraints often presents in a real-life pavement preservation programming problems and the trade-off considerations required between preventive maintenance, rehabilitation and reconstruction, present yet another factor that contributes to the solution complexity. In this research study, a new integrated multi-year optimization procedure was developed to solve network level pavement preservation programming problems, through cost-effectiveness based evolutionary programming analysis, using the Shuffled Complex Evolution (SCE) algorithm.^ A case study problem was analyzed to illustrate the robustness and consistency of the SCE technique in solving network level pavement preservation problems. The output from this program is a list of maintenance and rehabilitation treatment (M&R) strategies for each identified segment of the network in each programming year, and the impact on the overall performance of the network, in terms of the performance levels of the recommended optimal M&R strategy. ^ The results show that the SCE is very efficient and consistent in the simultaneous consideration of the trade-off between various pavement preservation strategies, while preserving the identity of the individual network segments. The flexibility of the technique is also demonstrated, in the sense that, by suitably coding the problem parameters, it can be used to solve several forms of pavement management programming problems. It is recommended that for large networks, some sort of decomposition technique should be applied to aggregate sections, which exhibit similar performance characteristics into links, such that whatever M&R alternative is recommended for a link can be applied to all the sections connected to it. In this way the problem size, and hence the solution time, can be greatly reduced to a more manageable solution space. ^ The study concludes that the robust search characteristics of SCE are well suited for solving the combinatorial problems in long-term network level pavement M&R programming and provides a rich area for future research. ^

Investigações sobre técnicas de arquivamento para otimizadores multiobjetivo

Multi-objective problems may have many optimal solutions, which together form the Pareto optimal set. A class of heuristic algorithms for those problems, in this work called optimizers, produces approximations of this optimal set. The approximation set kept by the optmizer may be limited or unlimited. The benefit of using an unlimited archive is to guarantee that all the nondominated solutions generated in the process will be saved. However, due to the large number of solutions that can be generated, to keep an archive and compare frequently new solutions to the stored ones may demand a high computational cost. The alternative is to use a limited archive. The problem that emerges from this situation is the need of discarding nondominated solutions when the archive is full. Some techniques were proposed to handle this problem, but investigations show that none of them can surely prevent the deterioration of the archives. This work investigates a technique to be used together with the previously proposed ideas in the literature to deal with limited archives. The technique consists on keeping discarded solutions in a secondary archive, and periodically recycle these solutions, bringing them back to the optimization. Three methods of recycling are presented. In order to verify if these ideas are capable to improve the archive content during the optimization, they were implemented together with other techniques from the literature. An computational experiment with NSGA-II, SPEA2, PAES, MOEA/D and NSGA-III algorithms, applied to many classes of problems is presented. The potential and the difficulties of the proposed techniques are evaluated based on statistical tests.

Investigações sobre técnicas de arquivamento para otimizadores multiobjetivo

Multi-objective problems may have many optimal solutions, which together form the Pareto optimal set. A class of heuristic algorithms for those problems, in this work called optimizers, produces approximations of this optimal set. The approximation set kept by the optmizer may be limited or unlimited. The benefit of using an unlimited archive is to guarantee that all the nondominated solutions generated in the process will be saved. However, due to the large number of solutions that can be generated, to keep an archive and compare frequently new solutions to the stored ones may demand a high computational cost. The alternative is to use a limited archive. The problem that emerges from this situation is the need of discarding nondominated solutions when the archive is full. Some techniques were proposed to handle this problem, but investigations show that none of them can surely prevent the deterioration of the archives. This work investigates a technique to be used together with the previously proposed ideas in the literature to deal with limited archives. The technique consists on keeping discarded solutions in a secondary archive, and periodically recycle these solutions, bringing them back to the optimization. Three methods of recycling are presented. In order to verify if these ideas are capable to improve the archive content during the optimization, they were implemented together with other techniques from the literature. An computational experiment with NSGA-II, SPEA2, PAES, MOEA/D and NSGA-III algorithms, applied to many classes of problems is presented. The potential and the difficulties of the proposed techniques are evaluated based on statistical tests.

Optimization of Cooling Protocols for Hearts Destined for Transplantation

Design and analysis of conceptually different cooling systems for the human heart preservation are numerically investigated. A heart cooling container with required connections was designed for a normal size human heart. A three-dimensional, high resolution human heart geometric model obtained from CT-angio data was used for simulations. Nine different cooling designs are introduced in this research. The first cooling design (Case 1) used a cooling gelatin only outside of the heart. In the second cooling design (Case 2), the internal parts of the heart were cooled via pumping a cooling liquid inside both the heart’s pulmonary and systemic circulation systems. An unsteady conjugate heat transfer analysis is performed to simulate the temperature field variations within the heart during the cooling process. Case 3 simulated the currently used cooling method in which the coolant is stagnant. Case 4 was a combination of Case 1 and Case 2. A linear thermoelasticity analysis was performed to assess the stresses applied on the heart during the cooling process. In Cases 5 through 9, the coolant solution was used for both internal and external cooling. For external circulation in Case 5 and Case 6, two inlets and two outlets were designed on the walls of the cooling container. Case 5 used laminar flows for coolant circulations inside and outside of the heart. Effects of turbulent flow on cooling of the heart were studied in Case 6. In Case 7, an additional inlet was designed on the cooling container wall to create a jet impinging the hot region of the heart’s wall. Unsteady periodic inlet velocities were applied in Case 8 and Case 9. The average temperature of the heart in Case 5 was +5.0oC after 1500 s of cooling. Multi-objective constrained optimization was performed for Case 5. Inlet velocities for two internal and one external coolant circulations were the three design variables for optimization. Minimizing the average temperature of the heart, wall shear stress and total volumetric flow rates were the three objectives. The only constraint was to keep von Mises stress below the ultimate tensile stress of the heart’s tissue.

Probabilistic design optimization of horizontal axis wind turbine rotors

Considerable interest in renewable energy has increased in recent years due to the concerns raised over the environmental impact of conventional energy sources and their price volatility. In particular, wind power has enjoyed a dramatic global growth in installed capacity over the past few decades. Nowadays, the advancement of wind turbine industry represents a challenge for several engineering areas, including materials science, computer science, aerodynamics, analytical design and analysis methods, testing and monitoring, and power electronics. In particular, the technological improvement of wind turbines is currently tied to the use of advanced design methodologies, allowing the designers to develop new and more efficient design concepts. Integrating mathematical optimization techniques into the multidisciplinary design of wind turbines constitutes a promising way to enhance the profitability of these devices. In the literature, wind turbine design optimization is typically performed deterministically. Deterministic optimizations do not consider any degree of randomness affecting the inputs of the system under consideration, and result, therefore, in an unique set of outputs. However, given the stochastic nature of the wind and the uncertainties associated, for instance, with wind turbine operating conditions or geometric tolerances, deterministically optimized designs may be inefficient. Therefore, one of the ways to further improve the design of modern wind turbines is to take into account the aforementioned sources of uncertainty in the optimization process, achieving robust configurations with minimal performance sensitivity to factors causing variability. The research work presented in this thesis deals with the development of a novel integrated multidisciplinary design framework for the robust aeroservoelastic design optimization of multi-megawatt horizontal axis wind turbine (HAWT) rotors, accounting for the stochastic variability related to the input variables. The design system is based on a multidisciplinary analysis module integrating several simulations tools needed to characterize the aeroservoelastic behavior of wind turbines, and determine their economical performance by means of the levelized cost of energy (LCOE). The reported design framework is portable and modular in that any of its analysis modules can be replaced with counterparts of user-selected fidelity. The presented technology is applied to the design of a 5-MW HAWT rotor to be used at sites of wind power density class from 3 to 7, where the mean wind speed at 50 m above the ground ranges from 6.4 to 11.9 m/s. Assuming the mean wind speed to vary stochastically in such range, the rotor design is optimized by minimizing the mean and standard deviation of the LCOE. Airfoil shapes, spanwise distributions of blade chord and twist, internal structural layup and rotor speed are optimized concurrently, subject to an extensive set of structural and aeroelastic constraints. The effectiveness of the multidisciplinary and robust design framework is demonstrated by showing that the probabilistically designed turbine achieves more favorable probabilistic performance than those of the initial baseline turbine and a turbine designed deterministically.

Development of a Computer-Based methodology for tolerance selection and optimization applied to the automotive sector

The design optimization of industrial products has always been an essential activity to improve product quality while reducing time-to-market and production costs. Although cost management is very complex and comprises all phases of the product life cycle, the control of geometrical and dimensional variations, known as Dimensional Management (DM), allows compliance with product and process requirements. Hence, the tolerance-cost optimization becomes the main practice to provide an effective application of Design for Tolerancing (DfT) and Design to Cost (DtC) approaches by enabling a connection between product tolerances and associated manufacturing costs. However, despite the growing interest in this topic, a profitable application in the industry of these techniques is hampered by their complexity: the definition of a systematic framework is the key element to improving design optimization, enhancing the concurrent use of Computer-Aided tools and Model-Based Definition (MBD) practices. The present doctorate research aims to define and develop an integrated methodology for product/process design optimization, to better exploit the new capabilities of advanced simulations and tools. By implementing predictive models and multi-disciplinary optimization, a Computer-Aided Integrated framework for tolerance-cost optimization has been proposed to allow the integration of DfT and DtC approaches and their direct application for the design of automotive components. Several case studies have been considered, with the final application of the integrated framework on a high-performance V12 engine assembly, to achieve both functional targets and cost reduction. From a scientific point of view, the proposed methodology provides an improvement for the tolerance-cost optimization of industrial components. The integration of theoretical approaches and Computer-Aided tools allows to analyse the influence of tolerances on both product performance and manufacturing costs. The case studies proved the suitability of the methodology for its application in the industrial field, providing the identification of further areas for improvement and refinement.