An experimental research investigation into disused flat rail wagons as bridges with applications for low volume rural roads in Australia

An experimental laboratory investigation was carried out to assess the structural adequacy of a disused PHO Class Flat Bottom Rail Wagon (FRW) for a single lane low volume road bridge application as per the design provisions of the Australian Bridge Design Standard AS 5100(2004). The investigation also encompassed a review into the risk associated with the pre-existing damage in wagons incurred during their service life on rail. The main objective of the laboratory testing of the FRW was to physically measure its performance under the same applied traffic loading it would be required to resist as a road bridge deck. In order to achieve this a full width (5.2m) single lane, single span (approximately 10m), simply supported bridge would be required to be constructed and tested in a structural laboratory. However, the available clear spacing between the columns of the loading portal frame encountered within the laboratory was insufficient to accommodate the 5.2m wide bridge deck excluding clearance normally considered necessary in structural testing. Therefore, only half of the full scale bridge deck (single FRW of width 2.6m) was able to be accommodated and tested; with the continuity of the bridge deck in the lateral direction applied as boundary constraints along the full length of the FRW at six selected locations. This represents a novel approach not yet reported in the literature for bridge deck testing to the best of the knowledge of the author. The test was carried out under two loadings provided in AS 5100 (2004) – one stationary W80 wheel load and the second a moving axle load M1600. As the bridge investigated in the study is a single lane single span low volume road bridge, the risk of pre-existing damage and the expected high cycle fatigue failure potential was assessed as being minimal and hence the bridge deck was not tested structurally for fatigue/ fracture. The high axle load requirements have instead been focussed upon the investigation into the serviceability and ultimate limit state requirements. The testing regime adopted however involved extensive recording of strains and deflections at several critical locations of the FRW. Three locations of W80 point load and two locations of the M1600 Axle load were considered for the serviceability testing; the FRW was also tested under the ultimate load dictated by the M1600. The outcomes of the experimental investigation have demonstrated that the FRW is structurally adequate to resist the prescribed traffic loadings outlaid in AS 5100 (2004). As the loading was directly applied on to the FRW, the laboratory testing is assessed as being significantly conservative. The FRW bridge deck in the field would only resist the load transferred by the running platform, where, depending on the design, composite action might exist – thereby the share of the loading which needs to be resisted by the FRW would be smaller than the system tested in the lab. On this basis, a demonstration bridge is under construction at the time of writing this thesis and future research will involve field testing in order to assess its performance.

Qualified indefeasibility and the careless mortgagee

In recent years a great deal of case law has been generated in relation to mortgages where the mortgagee has not engaged in adequate identity verification of the mortgagor and the mortgage has subsequently been found to be forged. As a result, careless mortgagee provisions operate in Queensland as an exception to indefeasibility. Similar provisions are expected to commence soon in New South Wales. This article examines the mortgagee’s position with the benefit of indefeasibility and then considers the impact of the careless mortgagee provisions on the rights of a mortgagee under a forged mortgage, concluding that the provisions significantly change the dynamic between a registered mortgagee and registered owner who has not signed the mortgage. These provisions appear to give the mortgagee a conditional indefeasibility, with the intention of reducing the State’s exposure to the payment of compensation in the case of identity fraud. They are however, more successful in the case of forgery by a third party rather than forgery by a co-owner.

Identity management : strengthening one-time password authentication through usability

Usability in HCI (Human-Computer Interaction) is normally understood as the simplicity and clarity with which the interaction with a computer program or a web site is designed. Identity management systems need to provide adequate usability and should have a simple and intuitive interface. The system should not only be designed to satisfy service provider requirements but it has to consider user requirements, otherwise it will lead to inconvenience and poor usability for users when managing their identities. With poor usability and a poor user interface with regard to security, it is highly likely that the system will have poor security. The rapid growth in the number of online services leads to an increasing number of different digital identities each user needs to manage. As a result, many people feel overloaded with credentials, which in turn negatively impacts their ability to manage them securely. Passwords are perhaps the most common type of credential used today. To avoid the tedious task of remembering difficult passwords, users often behave less securely by using low entropy and weak passwords. Weak passwords and bad password habits represent security threats to online services. Some solutions have been developed to eliminate the need for users to create and manage passwords. A typical solution is based on generating one-time passwords, i.e. passwords for single session or transaction usage. Unfortunately, most of these solutions do not satisfy scalability and/or usability requirements, or they are simply insecure. In this thesis, the security and usability aspects of contemporary methods for authentication based on one-time passwords (OTP) are examined and analyzed. In addition, more scalable solutions that provide a good user experience while at the same time preserving strong security are proposed.

Development and evaluation of the Clinician Suicide Risk Assessment Checklist

This paper describes the development and evaluation of a new instrument - the Clinician Suicide Risk Assessment Checklist (CSRAC). The instrument assesses the clinician's competency in three areas: clinical interviewing, assessment of specific suicide risk factors, and formulating a management plan. A draft checklist was constructed by integrating information from 1) literature review 2) expert clinician focus group and 3) consultation with experts. It was utilised in a simulated clinical scenario with clinician trainees and a trained actor in order to test for inter-rater agreement. Agreement was calculated and the checklist was re-drafted with the aim of maximising agreement. A second phase of simulated clinical scenarios was then conducted and inter-rater agreement was calculated for the revised checklist. In the first phase of the study, 18 of 35 items had inadequate inter-rater agreement (60%>), while in the second phase, using the revised version, only 3 of 39 items failed to achieve adequate inter-rater agreement. Further evidence of reliability and validity are required. Continued development of the CSRAC will be necessary before it can be utilised to assess the effectiveness of risk assessment training programs.

Work-related subjective experiences among community residents with schizophrenia or schizoaffective disorder

Objective: To develop a self-report scale of subjective experiences of illness perceived to impact on employment functioning, as an alternative to a diagnostic perspective, for anticipating the vocational assistance needs of people with schizophrenia or schizoaffective disorders. Method: A repeated measures pilot study (n1 = 26, n2 = 21) of community residents with schizophrenia identified a set of work-related subjective experiences perceived to impact on employment functioning. Items with the best psychometric properties were applied in a 12 month longitudinal survey of urban residents with schizophrenia or schizoaffective disorder (n1 = 104; n2 = 94; n3 = 94). Results: Construct validity, factor structure, responsiveness, internal consistency, stability, and criterion validity investigations produced favourable results. Work-related subjective experiences provide information about the intersection of the person, the disorder, and expectations of employment functioning, which suggest new opportunities for vocational professionals to explore and discuss individual assistance needs. Conclusion: Further psychometric investigations of test-retest reliability, discriminant and predictive validity, and research applications in supported employment and vocational rehabilitation, are recommended. Subject to adequate psychometric properties, the new measure promises to facilitate exploring: individuals' specific subjective experiences; how each is perceived to contribute to employment restrictions; and the corresponding implications for specialized treatment, vocational interventions and workplace accommodations.

The PSS : From Flat Maps to Layered Perspectives - the contribution of the Airport Metropolis Planning Support System (PSS) to sub-regional planning in the Brisbane Airport case environment

Conventional planning and decision making, with its sectoral and territorial emphasis and flat-map based processes are no longer adequate or appropriate for the increased complexity confronting airport/city interfaces. These crowed and often contested governance spaces demand a more iterative and relational planning and decision-making approach. Emergent GIS based planning and decision-making tools provide a mechanism which integrate and visually display an array of complex data, frameworks and scenarios/expectations, often in ‘real time’ computations. In so doing, these mechanisms provide a common ground for decision making and facilitate a more ‘joined-up’ approach to airport/city planning. This paper analyses the contribution of the Airport Metropolis Planning Support System (PSS) to sub-regional planning in the Brisbane Airport case environment.

The right to be green: using human rights law to achieve environmental protection

The relationship between the environment and human rights has long been recognised. It is now largely accepted that a ‘good’ environment is a necessary precondition for the enjoyment of a wide range of human rights, including the right to health, the right to an adequate standard of living, and even the right to life. It has even been suggested that as humans we all possess a right to live in an environment of a certain standard, based on the intrinsic value of the natural world to all human beings. In this context much has been written regarding the important role that the environment plays in human lives. This paper looks at the flip-side of this discussion, and examines what human rights can do for the environment. It is argued that, while there are valid criticisms for linking environmental protection too strongly to human needs, there is nonetheless much to be gained from using human rights law as a framework to achieve environmental protection.

The status of Australian nurse practitioners : the second national census

Objectives. To profile Australian nurse practitioners and their practice in 2009 and compare results with a similar 2007 census. Methods. Self-administered questionnaire. Results. Atotal of 293 nurse practitioners responded (response rate 76.3%). The majority were female (n = 229, 81.2%); mean age was 47.3 years (s.d. = 8.1). As in 2007, emergency nurse practitioners represented the largest clinical specialty (n = 63, 30.3%). A majority practiced in a metropolitan area (n = 133, 64.3%); a decrease from 2007. Consistent with 2007, only 71.5% (n = 208) were employed as a nurse practitioner and 22.8% (n = 46) were awaiting approval for some or all of their clinical protocols. Demographic data, allocations of tasks, and patterns of practice remained consistent with 2007 results. ‘No Medicare provider number’ (n = 182, 91.0%), ‘no authority to prescribe using the Pharmaceutical Benefits Scheme’ (n = 182, 89.6%) and ‘lack of organisational support’ (n = 105, 52.2%) were reported as ‘limiting’ or ‘extremely limiting’ to practice. Conclusions. Our results demonstrate less than satisfactory uptake of the nurse practitioner role despite authorisation. Barriers constraining nurse practitioner practice reduced but remained unacceptably high. Adequate professional and political support is necessary to ensure the efficacy and sustainability of this clinical role.

What happened to the education revolution? : new media technologies and the Australian curriculum : constraints and possibilities

This chapter investigates the place of new media in Queensland in the light of the Australian curriculum. ‘Multimodal texts’ in English are being defined as largely electronically ‘created’ and yet restricted access to digital resources at the chalkface may preclude this work from happening. The myth of the ‘digital native’ (Prensky, 2007), combined with the reality of the ‘digital divide’ coupled with technophobia amongst some quite experienced teachers, responsible for implementing the curriculum, paints a picture of constraints. These constraints are due in part to protective state bans in Queensland on social networking sites and school bans on mobile phone use. Some ‘Generation next’ will have access to digital platforms for the purpose of designing texts at home and school, and others will not. Yet without adequate Professional Development for teachers and substantially increased ICT infrastructure funding for all schools, the way new media and multimodal opportunities are interpreted at state level in the curriculum may leave much to be desired in schools. This chapter draws on research that I recently conducted on the professional development needs of beginning teachers, as well as a critical reading of the ACARA policy documents.

Using cooperative vehicle systems to collect near collision incidents events : a simulation study

On the road, near collision events (also close calls or near-miss incidents) largely outnumber actual crashes, yet most of them can never be recorded by current traffic data collection technologies or crashes analysis tools. The analysis of near collisions data is an important step in the process of reducing the crash rate. There have been several studies that have investigated near collisions; to our knowledge, this is the first study that uses the functionalities provided by cooperative vehicles to collect near misses information. We use the VISSIM traffic simulator and a custom C++ engine to simulate cooperative vehicles and their ability to detect near collision events. Our results showed that, within a simple simulated environment, adequate information on near collision events can be collected using the functionalities of cooperative perception systems. The relationship between the ratio of detected events and the ratio of equipped vehicle was shown to closely follow a squared law, and the largest source of nondetection was packet loss instead of packet delays and GPS imprecision.

Influence of physical and chemical properties of solids on heavy metal adsorption

Partition of heavy metals between particulate and dissolve fraction of stormwater primarily depends on the adsorption characteristics of solids particles. Moreover, the bioavailability of heavy metals is also influenced by the adsorption behaviour of solids. However, due to the lack of fundamental knowledge in relation to the heavy metals adsorption processes of road deposited solids, the effectiveness of stormwater management strategies can be limited. The research study focused on the investigation of the physical and chemical parameters of solids on urban road surfaces and, more specifically, on heavy metal adsorption to solids. Due to the complex nature of heavy metal interaction with solids, a substantial database was generated through a series of field investigations and laboratory experiments. The study sites for the build-up pollutant sample collection were selected from four urbanised suburbs located in a major river catchment. Sixteen road sites were selected from these suburbs and represented typical industrial, commercial and residential land uses. Build-up pollutants were collected using a wet and dry vacuum collection technique which was specially designed to improve fine particle collection. Roadside soil samples were also collected from each suburb for comparison with the road surface solids. The collected build-up solids samples were separated into four particle size ranges and tested for a range of physical and chemical parameters. The solids build-up on road surfaces contained a high fraction (70%) of particles smaller than 150ìm, which are favourable for heavy metal adsorption. These solids particles predominantly consist of soil derived minerals which included quartz, albite, microcline, muscovite and chlorite. Additionally, a high percentage of amorphous content was also identified in road deposited solids. In comparing the mineralogical data of surrounding soil and road deposited solids, it was found that about 30% of the solids consisted of particles generated from traffic related activities on road surfaces. Significant difference in mineralogical composition was noted in different particle sizes of build-up solids. Fine solids particles (<150ìm) consisted of a clayey matrix and high amorphous content (in the region of 40%) while coarse particles (>150ìm) consisted of a sandy matrix at all study sites, with about 60% quartz content. Due to these differences in mineralogical components, particles larger than and smaller than 150ìm had significant differences in their specific surface area (SSA) and effective cation exchange capacity (ECEC). These parameters, in turn, exert a significant influence on heavy metal adsorption. Consequently, heavy metal content in >150ìm particles was lower than in the case of fine particles. The particle size range <75ìm had the highest heavy metal content, corresponding with its high clay forming minerals, high organic matter and low quartz content which increased the SSA, ECEC and the presence of Fe, Al and Mn oxides. The clay forming minerals, high organic matter and Fe, Al and Mn oxides create distinct groups of charge sites on solids surfaces and exhibit different adsorption mechanisms and bond strength, between heavy metal elements and charge sites. Therefore, the predominance of these factors in different particle sizes leads to different heavy metal adsorption characteristics. Heavy metals show preference for association with clay forming minerals in fine solids particles, whilst in coarse particles heavy metals preferentially associate with organic matter. Although heavy metal adsorption to amorphous material is very low, the heavy metals embedded in traffic related materials have a potential impact on stormwater quality.Adsorption of heavy metals is not confined to an individual type of charge site in solids, whereas specific heavy metal elements show preference for adsorption to several different types of charge sites in solids. This is attributed to the dearth of preferred binding sites and the inability to reach the preferred binding sites due to competition between different heavy metal species. This confirms that heavy metal adsorption is significantly influenced by the physical and chemical parameters of solids that lead to a heterogeneity of surface charge sites. The research study highlighted the importance of removal of solids particles from stormwater runoff before they enter into receiving waters to reduce the potential risk posed by the bioavailability of heavy metals. The bioavailability of heavy metals not only results from the easily mobile fraction bound to the solids particles, but can also occur as a result of the dissolution of other forms of bonds by chemical changes in stormwater or microbial activity. Due to the diversity in the composition of the different particle sizes of solids and the characteristics and amount of charge sites on the particle surfaces, investigations using bulk solids are not adequate to gain an understanding of the heavy metal adsorption processes of solids particles. Therefore, the investigation of different particle size ranges is recommended for enhancing stormwater quality management practices.

The relationship between parents’ self-efficacy beliefs, outcome expectations, child behaviour, and management of atopic dermatitis

Atopic dermatitis (AD) is a chronic inflammatory skin condition, characterized by intense pruritis, with a complex aetiology comprising multiple genetic and environmental factors. It is a common chronic health problem among children, and along with other allergic conditions, is increasing in prevalence within Australia and in many countries worldwide. Successful management of childhood AD poses a significant and ongoing challenge to parents of affected children. Episodic and unpredictable, AD can have profound effects on children’s physical and psychosocial wellbeing and quality of life, and that of their caregivers and families. Where concurrent child behavioural problems and parenting difficulties exist, parents may have particular difficulty achieving adequate and consistent performance of the routine management tasks that promote the child’s health and wellbeing. Despite frequent reports of behaviour problems in children with AD, past research has neglected the importance of child behaviour to parenting confidence and competence with treatment. Parents of children with AD are also at risk of experiencing depression, anxiety, parenting stress, and parenting difficulties. Although these factors have been associated with difficulty in managing other childhood chronic health conditions, the nature of these relationships in the context of child AD management has not been reported. This study therefore examined relationships between child, parent, and family variables, and parents’ management of child AD and difficult child behaviour, using social cognitive and self-efficacy theory as a guiding framework. The study was conducted in three phases. It employed a quantitative, cross-sectional study design, accessing a community sample of 120 parents of children with AD, and a sample of 64 child-parent dyads recruited from a metropolitan paediatric tertiary referral centre. In Phase One, instruments designed to measure parents’ self-reported performance of AD management tasks (Parents’ Eczema Management Scale – PEMS) and parents’ outcome expectations of task performance (Parents’ Outcome Expectations of Eczema Management Scale – POEEMS) were adapted from the Parental Self-Efficacy with Eczema Care Index (PASECI). In Phase Two, these instruments were used to examine relationships between child, parent, and family variables, and parents’ self-efficacy, outcome expectations, and self-reported performance of AD management tasks. Relationships between child, parent, and family variables, parents’ self-efficacy for managing problem behaviours, and reported parenting practices, were also examined. This latter focus was explored further in Phase Three, in which relationships between observed child and parent behaviour, and parent-reported self-efficacy for managing both child AD and problem behaviours, were explored. Phase One demonstrated the reliability of both PEMS and POEEMS, and confirmed that PASECI was reliable and valid with modification as detailed. Factor analyses revealed two-factor structures for PEMS and PASECI alike, with both scales containing factors related to performing routine management tasks, and managing the child’s symptoms and behaviour. Factor analysis was also applied to POEEMS resulting in a three-factor structure. Factors relating to independent management of AD by the parent, involving healthcare professionals in management, and involving the child in management of AD were found. Parents’ self-efficacy and outcome expectations had a significant influence on self-reported task performance. In Phase Two, relationships emerged between parents’ self-efficacy and self-reported performance of AD management tasks, and AD severity, child behaviour difficulties, parent depression and stress, conflict over parenting issues, and parents’ relationship satisfaction. Using multiple linear regressions, significant proportions of variation in parents’ self-efficacy and self-reported performance of AD management tasks were explained by child behaviour difficulties and parents’ formal education, and self-efficacy emerged as a likely mediator for the relationships between both child behaviour and parents’ education, and performance of AD management tasks. Relationships were also found between parents’ self-efficacy for managing difficult child behaviour and use of dysfunctional parenting strategies, and child behaviour difficulties, parents’ depression and stress, conflict over parenting issues, and relationship satisfaction. While significant proportions of variation in self-efficacy for managing child behaviour were explained by both child behaviour and family income, family income was the only variable to explain a significant proportion of variation in parent-reported use of dysfunctional parenting strategies. Greater use of dysfunctional parenting strategies (both lax and authoritarian parenting) was associated with more severe AD. Parents reporting lower self-efficacy for managing AD also reported lower self-efficacy for managing difficult child behaviour; likewise, less successful self-reported performance of AD management tasks was associated with greater use of dysfunctional parenting strategies. When child and parent behaviour was directly observed in Phase Three, more aversive child behaviour was associated with lower self-efficacy, less positive outcome expectations, and poorer self-reported performance of AD management tasks by parents. Importantly, there were strong positive relationships between these variables (self-efficacy, outcome expectations, and self-reported task performance) and parents’ observed competence when providing treatment to their child. Less competent performance was also associated with greater parent-reported child behaviour difficulties, parent depression and stress, parenting conflict, and relationship dissatisfaction. Overall, this study revealed the importance of child behaviour to parents’ confidence and practices in the contexts of child AD and child behaviour management. Parents of children with concurrent AD and behavioural problems are at particular risk of having low self-efficacy for managing their child’s AD and difficult behaviour. Children with more severe AD are also at higher risk of behaviour problems, and thus represent a high-risk group of children whose parents may struggle to manage the disease successfully. As one of the first studies to examine the role and correlates of parents’ self-efficacy in child AD management, this study identified a number of potentially modifiable factors that can be targeted to enhance parents’ self-efficacy, and improve parent management of child AD. In particular, interventions should focus on child behaviour and parenting issues to support parents caring for children with AD and improve child health outcomes. In future, findings from this research will assist healthcare teams to identify parents most in need of support and intervention, and inform the development and testing of targeted multidisciplinary strategies to support parents caring for children with AD.

Risk-informed thinking in airports: the application of business continuity management in airport infrastructure

Airports worldwide represent key forms of critical infrastructure in addition to serving as nodes in the international aviation network. While the continued operation of airports is critical to the functioning of reliable air passenger and freight transportation, these infrastructure systems face a number of sources of disturbance that threaten their operational viability. Recent examples of high magnitude events include the eruption of Iceland’s Eyjafjallajokull volcano eruption (Folattau and Schofield 2010), the failure of multiple systems at the opening of Heathrow’s Terminal 5 (Brady and Davies 2010) and the Glasgow airport 2007 terrorist attack (Crichton 2008). While these newsworthy events do occur, a multitude of lower-level more common disturbances also have the potential to cause significant discontinuity to airport operations. Regional airports face a unique set of challenges, particularly in a nation like Australia where they serve to link otherwise remote and isolated communities to metropolitan hubs (Wheeler 2005), often without the resources and political attention received by larger capital city airports. This paper discusses conceptual relationships between Business Continuity Management (BCM) and High Reliability Theory, and proposes BCM as an appropriate risk-based management process to ensure continued airport operation in the face of uncertainty. In addition, it argues that that correctly implemented BCM can lead to highly reliable organisations. This is framed within the broader context of critical infrastructures and the need for adequate crisis management approaches suited to their unique requirements (Boin and McConnell 2007).

Centrifuging rotary vacuum filter mud at Tully Mill

Disposal of mud and ash, particularly in wet weather conditions, is a significant expense for mills. This paper reports on one part of a process to pelletise mud and ash, aimed at making mud and ash more attractive to growers across entire mill districts. The full process is described in a separate paper. The part described in this paper involves re-constituting mud cake from the filter station at Tully Mill and processing it in a decanter centrifuge. The material produced by re-constituting and centrifuging is drier and made up of separate particles. The material needs to mix easily with boiler ash, and the mixture needs to be fed easily into a flue gas drier to be dried to low moisture. The results achieved with the particular characteristics of Tully Mill rotary vacuum filter cake are presented. It was found that an internal rotor with a 20º beach was not adequate to process re-constituted rotary vacuum filter mud. A rotor with a 10º beach worked much more successfully. A total of four tonnes of centrifuged mud with a moisture content ranging from 60% to 65% was produced. It was found that the torque, flocculant rate and dose rate had a statistically significant effect on the moisture content. Feed rate did not have a noticeable impact on the moisture content by itself but torque had a much larger impact on the moisture content at the low feed rate than at the high feed rate. These results indicated that the moisture content of the mud can most likely be reduced with low feed rate, low flocculant rate, high dose rate and high torque. One issue that is believed to affect the operation of a decanter centrifuge was the large quantity of long bagasse fibres in the rotary vacuum filter mud. It is likely that the long fibres limited the throughput of the centrifuge and the moisture achieved.

An additional step towards modelling the mechanical behaviour of sugar cane bagasse

A better understanding of the behaviour of prepared cane and bagasse, especially the ability to model the mechanical behaviour of bagasse as it is squeezed in a milling unit to extract juice, would help identify how to improve the current milling process; for example to reduce final bagasse moisture. Previous investigations have proven with certainty that juice flow through bagasse obeys Darcy’s permeability law, that the grip of the rough surface of the grooves on the bagasse can be represented by the Mohr- Coulomb failure criterion for soils, and that the internal mechanical behaviour of the bagasse can be represented by critical state behaviour similar to that of sand and clay. Current Finite Element Models (FEM) available in commercial software have adequate permeability models. However, commercial software does not contain an adequate mechanical model for bagasse. Progress has been made in the last ten years towards implementing a mechanical model for bagasse in finite element software code. This paper builds on that progress and carries out a further step towards obtaining an adequate material model. In particular, the prediction of volume change during shearing of normally consolidated final bagasse is addressed.