899 resultados para additive representability
Resumo:
L’Additive Manufacturing è una tecnologia che ormai da qualche anno sta diventando sempre piu’ utilizzata in numerosi ambiti, tra cui l’automotive. In questo settore sono molte le aziende che stanno sperimentando e cercando di inglobare tale processo al loro interno. Tra queste l’Università di Bologna, dove un team studentesco motociclistico si occupa della creazione di un prototipo di moto elettrica da competizione. Nell'intento di utilizzare tale tecnologia, sono numerose le informazioni necessarie per la corretta progettazione. Infatti, le caratteristiche dei materiali che vengono usati principalmente non sono ancora del tutto chiare e presentano alcuni aspetti poco investigati. Per questo motivo, in tale progetto si è deciso di caratterizzare a fatica provini realizzati in AlSi10Mg che presentassero una particolare geometria, per indagare anche l’influenza dello spessore. Sono quindi stati realizzati i campioni, anche con alcuni trattamenti di post-processo e sono poi stati osservati i risultati a fatica e alcune caratteristiche, tra cui: porosità, densità e struttura dei bagni di fusione. Tali valori riscontrati sono poi stati confrontati con quelli ottenuti in altri studi, cercando di comprendere differenze e motivazioni dei fenomeni osservati.
Resumo:
This study investigates the effect of an additive process in manufacturing of thick composites. Airstone 780 E epoxy resin and 785H Hardener system is used in the analysis since it is widely used wind turbine blade, namely thick components. As a fiber, fabric by SAERTEX (812 g/m2) with a 0-90 degrees layup direction is used. Temperature overshoot is a major issue during the manufacturing of thick composites. A high temperature overshoot leads to an increase in residual stresses. These residual stresses are causing warping, delamination, dimensional instability, and undesired distortion of composite structures. A coupled thermo-mechanical model capable of predicting cure induced residual stresses have been built using the commercial FE software Abaqus®. The possibility of building thick composite components by means of adding a finite number of sub-laminates has been investigated. The results have been compared against components manufactured following a standard route. The influence of pre-curing of the sub-laminates has also been addressed and results compared with standard practice. As a result of the study, it is found that introducing additive process can prevent temperature overshoot to occur and benefits the residual stresses generation during the curing process. However, the process time required increases by 50%, therefore increasing the manufacturing costs. An optimized cure cycle is required to minimize process time and cure induced defects simultaneously.
Resumo:
In recent years plastic is a key material, fundamental for a large variety of implications. But its large utilization has the direct consequence of the disposal of tons of wastes, that in the major amount cannot be recycled. To pose a solution to the issue of the increasing amount of plastics that are rapidly accumulating all over the world, it is necessary to switch to biodegradable materials. This dissertation is focused on a biodegradable and biobased plastic (polylactic acid, PLA), in order to set free the material from the market and issues of oil, but the PLA is very expensive. For this reason it was added a part of natural component derived from wastes (wheat middling), that acts as reinforcement and decreases the cost of the final material forming a biocomposite. Since their interaction is difficult, the purpose of this dissertation is to improve the affinity between the PLA and the wheat middling.
Resumo:
La tesi di laurea, di tipo sperimentale, nasce dall’esigenza di progettare un sistema di force feedback da installare sui comandi di un simulatore di volo per elicottero, prevedendo di utilizzare tecnologie additive per la produzione dei componenti. Sono state, quindi, presentate alcune proposte per il soddisfacimento dei requisiti di progetto. Tra le due soluzioni progettuali individuate, una è stata scartata, mentre l'altra, basata su un collare da montare sul comando del ciclico e su un disegno per il supporto del sistema di ritenuta, è stata sviluppata. Sono state fatte, di conseguenza, assieme a quelle di tipo progettuale, alcune scelte legate alla pianificazione meccanica (ad esempio, scelta delle viti e delle molle). Il risultato finale è un sistema di force feedback funzionante, in cui la leva del comando ciclico del simulatore di volo per elicottero oppone uno sforzo in seguito ad una deflessione da parte del pilota.
Resumo:
Questo studio si pone come obiettivo lo sviluppo e la sperimentazione di un metodo per eseguire un benchmarking di due diversi sistemi di Additive Manufacturing mediante macchina di misura a coordinate Renishaw Cyclone. In particolare sono valutate le prestazioni in termini di precisione di forma di un sistema di tipo FDM e di uno di tipo PolyJet al fine di ottenere dati indicanti le potenzialità di queste due tecnologie per parti di piccole dimensioni. Dopo un’introduzione generale sull’Additive Manufacturing, si scende nei dettagli delle due tecniche oggetto dello studio e si discute di come strutturare il piano sperimentale in funzione degli obiettivi dell’attività e dei metodi scelti per l’acquisizione e la valutazione dei dati. Si parte, infatti, con la fabbricazione di un modello di benchmark, le cui geometrie vengono poi rilevate tramite una macchina di misura a coordinate per ottenere i valori di precisione di forma, che sono presentati come tolleranze geometriche del sistema GD&T. Successivamente, si descrivono tutte le fasi dell’attività sperimentale, iniziando con l’ideazione del modello di benchmark e proseguendo con i processi di fabbricazione e misurazione, per poi arrivare alla deduzione dei valori di precisione di forma tramite un post-processing dei dati. Infine, si presentano i valori di tolleranza ottenuti e si traggono le conclusioni riguardo la riuscita dell’attività sperimentale e il confronto tra le due tecnologie di Additive Manufacturing.
Resumo:
Il progetto si presenta come un miglioramento di una particolare terapia sanitaria, dove la maggior parte dei pazienti, soprattutto quelli in un’età delicata, possono avvertire determinati problemi fisici o psicologici. La terapia in questione è la Chemioterapia, che consiste nella somministrazione di una o più sostanze capaci di aggredire le cellule tumorali che si moltiplicano grazie a una fleboclisi, ovvero una procedura che è in grado di somministrare via endovenosa una sostanza come il trattamento appena citato, sfruttando alcune vene solide del braccio come la Basilica. Grazie a un’esperienza personale, pareri (dottoressa Antonella Sau) e coinvolgimenti di altri pazienti dell’associazione AGBE che hanno avuto un problema simile, è stato possibile progettare e inventare un tutore polimerico ad alta compatibilità dermatologica, in grado di immobilizzare l’arto usato nella terapia regalando una maggiore comodità e stabilità sia della fleboclisi che del braccio stesso. Inizialmente il tutore sarà ideato prendendo specifiche misure dell’avambraccio/gomito del singolo paziente, per poi stamparlo in 3D e portarlo ad effettuare i cicli somministrati per combattere la malattia. A fine di tutto, il paziente avrà sostenuto una cura delicata come la Chemioterapia con un maggiore comfort, maggiore stabilità psicologica e soprattutto meno complicanze come stravaso, infezioni varie, fuoriuscite di sostante chemioterapeutiche, gonfiori, depressione e irritazioni endovenose.
Resumo:
Additive Manufacturing (AM), also known as “3D printing”, is a recent production technique that allows the creation of three-dimensional elements by depositing multiple layers of material. This technology is widely used in various industrial sectors, such as automotive, aerospace and aviation. With AM, it is possible to produce particularly complex elements for which traditional techniques cannot be used. These technologies are not yet widespread in the civil engineering sector, which is slowly changing thanks to the advantages of AM, such as the possibility of realizing elements without geometric restrictions, with less material usage and a higher efficiency, in particular employing Wire-and-Arc Additive Manufacturing (WAAM) technology. Buildings that benefit most from AM are all those structures designed using form-finding and free-form techniques. These include gridshells, where joints are the most critical and difficult elements to design, as the overall behaviour of the structure depends on them. It must also be considered that, during the design, the engineer must try to minimize the structure's own weight. Self-weight reductions can be achieved by Topological Optimization (TO) of the joint itself, which generates complex geometries that could not be made using traditional techniques. To sum up, weight reductions through TO combined with AM allow for several potential benefits, including economic ones. In this thesis, the roof of the British Museum is considered as a case study, analysing the gridshell structure of which a joint will be chosen to be designed and manufactured, using TO and WAAM techniques. Then, the designed joint will be studied in order to understand its structural behaviour in terms of stiffness and strength. Finally, a printing test will be performed to assess the production feasibility using WAAM technology. The computational design and fabrication stages were carried out at Technische Universität Braunschweig in Germany.
Resumo:
Although being studied only for few years, Wire and Arc Additive Manufacturing (WAAM) will become the predominant way of producing stainless-steel elements in a near-like future. The analysis and study of such elements has yet to be defined in a proper way, but the projects regarding this subject are innovating more and more thanks to the findings discovered by the latter. This thesis is focused on an initial stage on the analysis of mechanical and geometrical properties of such stainless-steel elements produced by MX3D laboratories in Amsterdam, and to perform a calibration of the design strength values by means of Annex D of Eurocode 0, which talks about the analysis of the semi-probabilistic safety factors, hence the definition of characteristic values. Moreover, after testing the stainless-steel specimens by means of strain gauges and after obtaining mechanical and geometrical properties, a statistical analysis of such properties and an evaluation of characteristic values is performed. After this, there is to execute the calibration of design strength values of WAAM inclined bars and intersections.
Resumo:
The 'dilution effect' (DE) hypothesis predicts that diverse host communities will show reduced disease. The underlying causes of pathogen dilution are complex, because they involve non-additive (driven by host interactions and differential habitat use) and additive (controlled by host species composition) mechanisms. Here, we used measures of complementarity and selection traditionally employed in the field of biodiversity-ecosystem function (BEF) to quantify the net effect of host diversity on disease dynamics of the amphibian-killing fungus Batrachochytrium dendrobatidis (Bd). Complementarity occurs when average infection load in diverse host assemblages departs from that of each component species in uniform populations. Selection measures the disproportionate impact of a particular species in diverse assemblages compared with its performance in uniform populations, and therefore has strong additive and non-additive properties. We experimentally infected tropical amphibian species of varying life histories, in single- and multi-host treatments, and measured individual Bd infection loads. Host diversity reduced Bd infection in amphibians through a mechanism analogous to complementarity (sensu BEF), potentially by reducing shared habitat use and transmission among hosts. Additionally, the selection component indicated that one particular terrestrial species showed reduced infection loads in diverse assemblages at the expense of neighbouring aquatic hosts becoming heavily infected. By partitioning components of diversity, our findings underscore the importance of additive and non-additive mechanisms underlying the DE.
Resumo:
Health economic evaluations require estimates of expected survival from patients receiving different interventions, often over a lifetime. However, data on the patients of interest are typically only available for a much shorter follow-up time, from randomised trials or cohorts. Previous work showed how to use general population mortality to improve extrapolations of the short-term data, assuming a constant additive or multiplicative effect on the hazards for all-cause mortality for study patients relative to the general population. A more plausible assumption may be a constant effect on the hazard for the specific cause of death targeted by the treatments. To address this problem, we use independent parametric survival models for cause-specific mortality among the general population. Because causes of death are unobserved for the patients of interest, a polyhazard model is used to express their all-cause mortality as a sum of latent cause-specific hazards. Assuming proportional cause-specific hazards between the general and study populations then allows us to extrapolate mortality of the patients of interest to the long term. A Bayesian framework is used to jointly model all sources of data. By simulation, we show that ignoring cause-specific hazards leads to biased estimates of mean survival when the proportion of deaths due to the cause of interest changes through time. The methods are applied to an evaluation of implantable cardioverter defibrillators for the prevention of sudden cardiac death among patients with cardiac arrhythmia. After accounting for cause-specific mortality, substantial differences are seen in estimates of life years gained from implantable cardioverter defibrillators.
Resumo:
A method using the ring-oven technique for pre-concentration in filter paper discs and near infrared hyperspectral imaging is proposed to identify four detergent and dispersant additives, and to determine their concentration in gasoline. Different approaches were used to select the best image data processing in order to gather the relevant spectral information. This was attained by selecting the pixels of the region of interest (ROI), using a pre-calculated threshold value of the PCA scores arranged as histograms, to select the spectra set; summing up the selected spectra to achieve representativeness; and compensating for the superimposed filter paper spectral information, also supported by scores histograms for each individual sample. The best classification model was achieved using linear discriminant analysis and genetic algorithm (LDA/GA), whose correct classification rate in the external validation set was 92%. Previous classification of the type of additive present in the gasoline is necessary to define the PLS model required for its quantitative determination. Considering that two of the additives studied present high spectral similarity, a PLS regression model was constructed to predict their content in gasoline, while two additional models were used for the remaining additives. The results for the external validation of these regression models showed a mean percentage error of prediction varying from 5 to 15%.
Resumo:
A common breeding strategy is to carry out basic studies to investigate the hypothesis of a single gene controlling the trait (major gene) with or without polygenes of minor effect. In this study we used Bayesian inference to fit genetic additive-dominance models of inheritance to plant breeding experiments with multiple generations. Normal densities with different means, according to the major gene genotype, were considered in a linear model in which the design matrix of the genetic effects had unknown coefficients (which were estimated in individual basis). An actual data set from an inheritance study of partenocarpy in zucchini (Cucurbita pepo L.) was used for illustration. Model fitting included posterior probabilities for all individual genotypes. Analysis agrees with results in the literature but this approach was far more efficient than previous alternatives assuming that design matrix was known for the generations. Partenocarpy in zucchini is controlled by a major gene with important additive effect and partial dominance.
Resumo:
Dados de bovinos compostos foram analisados para avaliar o efeito da epistasia nos modelos de avaliação genética. As características analisadas foram os pesos aos 205 (P205) e 390 dias (P390) e perímetro escrotal aos 390 dias (PE390). As análises foram realizadas pela metodologia de máxima verossimilhança considerando-se dois modelos: o modelo 1 incluiu como covariáveis os efeitos aditivos diretos e maternos, e os não aditivos das heterozigoses para os efeitos diretos e para o materno total, e o modelo 2 considerou também o efeito direto de epistasia. Para comparação dos modelos, foram utilizados o critério de informação de Akaike (AIC) e o critério de informação Bayesiano de Schwartz (BIC), e o teste de razão de verossimilhança. A inclusão da epistasia no modelo de avaliação genética pouco alterou as estimativas de componentes de (co)variâncias genéticas aditivas e, consequentemente, as herdabilidades. O teste de verossimilhança e o critério de Akaike sugeriram que o modelo 2, que inclui a epistasia, apresentou maior aderência aos dados para todas as características analisadas. O critério BIC indicou este modelo como o melhor apenas para P205. Para análise genética dessa população, o modelo que considerou o efeito de epistasia foi o mais adequado.
Resumo:
Objetivou-se neste trabalho estudar modelos com efeitos não-aditivos diretos e maternos em uma população composta em clima tropical, tentando minimizar esses efeitos para obtenção dos valores genéticos dos animais avaliados. Foram utilizados dados de animais de uma população composta, por meio da comparação de três modelos que incluíram os efeitos fixos de grupo contemporâneo, ordem de parto e heterose direta e materna e os efeitos aleatórios de efeito genético aditivo direto e materno. As análises foram realizadas em duas etapas; na primeira foram estudadas as estimativas dos efeitos raciais e de heterose individual e materna e na segunda etapa, calculadas as variâncias, herdabilidades e os valores genéticos dos animais. O efeito materno, quando não foi considerado no modelo, pareceu superestimar o efeito aditivo racial. Os efeitos aditivos raciais, racial materno e de heterose individual e materna influenciaram significativamente o ganho médio diário no pré-desmame, obtendo-se diferentes estimativas entre os tipos biológicos. Considerando o arquivo de dados corrigidos para os efeitos não-aditivos diretos e maternos, as herdabilidades direta e materna foram de 0,22 e 0,20, respectivamente. Os efeitos racial materno e de heterose individual e materna foram importantes fontes de variação para o ganho médio diário no pré-desmame e devem ser considerados durante a avaliação genética de uma população multirracial.
Resumo:
The ADH (alcohol dehydrogenase) system is one of the earliest known models of molecular evolution, and is still the most studied in Drosophila. Herein, we studied this model in the genus Anastrepha (Diptera, Tephritidae). Due to the remarkable advantages it presents, it is possible to cross species with different Adh genotypes and with different phenotype traits related to ethanol tolerance. The two species studied here each have a different number of Adh gene copies, whereby crosses generate polymorphisms in gene number and in composition of the genetic background. We measured certain traits related to ethanol metabolism and tolerance. ADH specific enzyme activity presented gene by environment interactions, and the larval protein content showed an additive pattern of inheritance, whilst ADH enzyme activity per larva presented a complex behavior that may be explained by epistatic effects. Regression models suggest that there are heritable factors acting on ethanol tolerance, which may be related to enzymatic activity of the ADHs and to larval mass, although a pronounced environmental effect on ethanol tolerance was also observed. By using these data, we speculated on the mechanisms of ethanol tolerance and its inheritance as well as of associated traits.