Influência de adjuvantes no espectro de gotas de ponta com indução de ar

This study aimed to verify the influence of adjuvants on the droplet spectrum of an air induction nozzle. The experiment used nine spray solutions, one including only water and eight containing adjuvants: Nimbus® (mineral oil), Óleo vegetal Nortox (vegetal oil), Li-700® (a mixture of lecithin and propionic acid), Agral® (nonyl phenoxy poly ethanol), In-Tec® (nonyl phenol ethoxylate), Antideriva (nonyl phenol ethoxylate), Silwet® L-77 Ag (copolymer polyester and silicon) and TA 35 (sodium lauryl ether sulfate). A flat fan air induction nozzle Hypro® Guardian Air 110 03 was used for the droplet spectrum evaluation. The study was conducted at the Laboratory for Particle Size Analysis (Lapar), at FCAV/UNESP, Jaboticabal/SP - Brazil. The determination of the droplet spectrum characteristics (Volume Median Diameter/VMD, percentage of droplets smaller than 100 micrometers and span) was carried out by a particle size analyzer by laser diffraction Mastersizer S (Malvern Instruments). For statistical analysis the mean values were compared using Confidence Interval at 95% (CI 95%). The results showed that for the Hypro® GA air induction nozzle the oil based adjuvants (Óleo Vegetal Nortox e Nimbus®) increased the VMD. The percentage of droplets smaller than 100 micrometers was lower for the Agral®, Antideriva, In-Tec® e TA 35, in comparison with the Óleo Vegetal Nortox and Li-700®. The span was higher for the oil based adjuvants (Óleo Vegetal Nortox e Nimbus®) and lower for the TA 35 (sodium lauryl ether sulfate), showing that the TA 35 adjuvant has a potential to improve the quality of the droplet spectrum of the Hypro® GA 11003 nozzle.

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

The aim of this study was to build and validate a low cost reduced-scale wind tunnel for drift evaluation on pesticide application technology. The work was carried out at the NEMPA - Núcleo de Ensaio de Máquinas e Pneus Agroflorestais (NEMPA), FCA/UNESP, Departamento de Engenharia Rural, Botucatu/SP, Brazil. The wind tunnel main characteristics were an open circuit and a closed working section with a fan blowing air into the tunnel. Screens were fitted downstream after the fan in order to stabilize the air flow on the working section. The tunnel was built with 3.0 mm eucalyptus hardboard, with a total length of 4.8 m and a squared section of 0.56 m. The air flow was provided by a 180 W axial fan. The system was adjusted and calibrated to provide a laminar and stable flow at 2.0 m s-1. Validation studies were carried out by using a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) to apply a spray solutions containing water plus a food dye (Blue FDC) at 0,6% m v-1 mixed with two adjuvants: a polymer based anti drift formulation at 0,06% m v-1 and a sodium lauryl ether sulfate based surfactant at 0,2% v v-1. After a 10-second application the drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The wind tunnel had low levels of turbulence and high repeatability of the data, which means that the flow was uniform and able to be used for carrying out measures to estimate drift. The validation results showed that the tunnel was effective to enable comparative drift measurements on the spray solution used in this work making possible the evaluation of drift risk potential under those spray technologies. The use of an adjuvant based on a polymer reduced the amount of drift from the nozzle compared to the surfactant.

Caracterização física e química e potencial de deriva de caldas contendo surfatantes em pulverizações agrícolas

The aim of this work was to evaluate the effect of the addition of different surfactants in physical and chemical properties of spray solutions, droplets spectra and drift potential on agricultural spraying. The surfactants and concentrations (v v-1) were: Haiten (0.1%), Antideriva and Intec (0.05% and 0.1%). The following characteristics were analyzed: surface tension, viscosity, density and electric conductivity. The droplet size spectrum was determined by a laser particle analyzer (Mastersizer S®, version 2.15) including measurements of volume medium diameter (VMD), the percent of droplets below 50 and 100 μm (V50 e V100) and index span. In order to estimate the drift potential, a series of wind tunnel tests were performed with a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) used to apply the spray solutions containing water, the adjuvants and a food color dye (Brilliant blue FD & C no 1) at 0,6% m v-1. The drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The results showed that the addition of adjuvants changed physical and chemical properties of spray solutions in different magnitudes according to the surfactant. Surfactants changed the droplet spectrum and drift potential, indicating that higher VMD and smaller V100 induced higher percentage of drift.

Eficácia do flutriafol e do flutriafol + tiofanato metílico aplicados com gotas finas ou médias no controle da ferrugem asiática da soja

The aim of this study was to evaluate the influence of fine and medium droplets in the performance of flutriafol and thiophanate methyl + flutriafol for the control of Asian Soybean Rust (Phakopsora pachyrhizi Sydow & Sydow). The experiment was a 2 x 2 factorial design (2 droplet sizes x 2 fungicides) resulting in four treatments with six replications. The experimental area was set up with 24 plots (50 x 21 m). In each plot there was a central assessment area with 10 x 20 m. To the each plot there was a non-treated area placed in opposed direction to the wind. The evaluations of rust control were made by of the calculation of incidence (percentage of plants with rust), severity (level of infection), defoliations and soybean yield. The results were analyzed by the calculation of the confidence interval at 90%. The study was set up in curative control conditions with average infestation of 68.6%, average severity in the lower part of the canopy was of 35.9% and on the upper parte it was 4.57%. The results of severity, defoliation and productivity did not show statistical difference among the treatments. However, it was observed that in general there was tendency of better results with the application of flutriafol alone comparing with thiophanate methyl + flutriafol, since there was a small difference between two commercial products in the flutriafol active ingredient content (62.5 g ha-1 to the flutriafol alone and 60 g ha-1 to the thiophanate methyl + flutriafol). There was no statistical difference between fine and medium droplets. This fact can be explained by the characteristics of systemic action of the flutriafol and by the type of control made (curative). The flutriafol, being a systemic fungicide is less sensitive to the better coverage provided by the smaller droplets and, on the curative control, the amount of product deposited can became more import than coverage, mainly on the superior part of the leaves. These leaves are healthier than the inferior leaves that in general are the first to become completely compromised by the rust, losing importance to the plant. By this reason, medium droplets appear to have offered similar performance even not offering advantages in the leaf coverage. This fact may become important because in the practical side of the use of medium droplets, since this may increase the amount of time to spray, mainly because the fine and very fine droplets have more limitations related to drift and evaporation.

Imagens aéreas multiespectrais na identificação de zonas de manejo em áreas de algodão para aplicação localizada de insumos

Crop yield is influenced by several factors with variability in time and space that are associated with the variations in the plant vigor. This variability allows the identification of management zones and site-specific applications to manage different regions of the field. The purpose of this study was the use of multispectral image for management zones identification and implications of site-specific application in commercial cotton areas. Multispectral airborne images from three years were used to classify a field into three vegetation classes via the Normalized Difference Vegetation Index (NDVI). The NDVI classes were used to verify the potential differences between plant physical measurements and identify management zones. The cotton plant measurements sampled in 8 repetitions of 10 plants at each NDVI class were Stand Count, Plant Height, Total Nodes and Total Bolls. Statistical analysis was performed with treatments arranged in split plot design with Tukey’s Test at 5% of probability. The images were classified into five NDVI classes to evaluate the relationship between cotton plant measurement results and sampling location across the field. The results have demonstrated the possibility of using multispectral image for management zones identification in cotton areas. The image classification into three NDVI classes showed three different zones in the field with similar characteristics for the studied years. Statistical differences were shown for plant height, total nodes and total bolls between low and high NDVI classes for all years. High NDVI classes contained plants with greater height, total nodes and total bolls compared to low NDVI classes. There was no difference in Stand Count between low and high NDVI classes for the three studied years. The final plant stand was the same between all NDVI classes for 2001 and 2003 as it was expected due to the conventional seeding application with the same rate of seeds for the entire field.

Inspeção periódica de pulverizadores nas principais regiões de produção de soja no Brasil

The aim of this study was to evaluate the evolution of calibration and maintenance practices for crop sprayers on soybean production areas in Brazil, in the 2006 and 2007 seasons, based on the Project IPP data. Therefore, the evaluation covered issues related to calibration, maintenance condition and the main components of 103 sprayers distributed in the following states: Rio Grande do Sul (35), Paraná (60), and, Mato Grosso do Sul (8). The evaluations were done at the rate of one sprayer per farm. The most frequent problems were related to the pressure gauge, spray leaks and calibration errors greater than 50% of the desired volume rate. The analysis of the application rate showed a tendency for the farmers to apply volume rates below the desired value. In 2006 the errors of the application rate were significant, with 70.4% for Rio Grande do Sul State, 74.5% for Paraná State and 37.5% for Mato Grosso do Sul State. In 2007 there was a reduction of errors, with averages of 50.0% for Rio Grande do Sul and 66.7% for Paraná. In general terms, the results showed improvements on the use, maintenance and calibration processes for crop sprayers on the areas covered by the Project IPP, with reductions on average indexes for calibration errors, leaks and bad tips, among other issues.

Remoção pela chuva de diferentes formulações de flutriafol aplicada em soja, com e sem a adição de óleo mineral na calda

The present study had as objectives to verify the effect of rainfastness of different flutriafol formulations, in laboratory conditions, applied on soybean plants with and without the oil adjuvant in the spray solution, as well as to verify the influence of the oil on the droplet spectrum. The experiment considered ten spray solutions related to five treatments containing flutriafol (four formulations of flutriafol and a flutriafol mixture with tebuconazole), all applied with and without mineral oil. Particles size analysis were based on the determination of the droplet spectrum, medium volumetric diameter and the amount of droplets below 100 μm. All the solutions were sprayed with Teejet XR 11001 (fine droplets). Droplet spectrum was determined in a direct way by diffraction of laser (Malvern Mastersizer S®, version 2.15). Confidence interval at 90% degree was used to compare the mean data. The results showed that the addition of mineral oil in the solutions provided tendencies of larger medium volumetric diameter, smaller amount of droplets below than 100 µm and better uniformity of the droplet spectrum. All of the solutions with the addition of mineral oil presented larger adhesion and/or absorption of the fungicide on the plants in comparison with the solutions without oil. The increase of the time between the application and the rain, caused reduction of the fungicide removal, independently of the rain intensity. The increase of the amount of rain didn't change the relative behavior among the solutions; however, this larger amount of rain caused larger fungicide removal along the time. It was observed significant removal of flutriafol by the rain up to 48 hours after the spray application.

Avaliação do tempo de resposta de um controlador de fluxo com DGPS submetido à variação de velocidade de voo em condições de voo simulado em laboratório

The application of pesticides is one of the most important steps in the agricultural production process. The spray volume can directly affect application success, and this parameter is directly dependent on the displacement speed of the sprayer. In conventional systems, the operator has to maintain a constant speed to ensure uniform application along the tracks. In order to improve over application quality and preserve levels of precision for applied doses; the use of electronic flow control systems allows for automatic adjustment of volume applied over the area when there is a change in velocity during application. The objective of this research was to study the response times of a flow controller with DGPS for aerial application subjected to variations of velocity in laboratory simulated flight conditions. For this purpose, a bench test has been developed including software for simulating DGPS signals, which was used to simulate different flight speeds and conditions. The results showed the average response time from the flow controller to a change in velocity to be between 6 and 20 seconds. Variations in total flow and the controller setting had a significant influence on response time with situations where there was interaction between the factors being evaluated. There was a tendency for better response times using a constant setting for the control algorithm other than that specified by the manufacturer. The flow controller presented an average error rates below 2% in all evaluated operating conditions, providing satisfactory accuracy in determining the output of product in different test situations.

Promoting ethical and environmental awareness in vulnerable communities: a research action plan

Urban populations that live in the outskirts of major Latin American cities usually face conditions of vulnerability attached to complex environmental issues, such as the lack of sewerage, floods, pollution and soil and water contamination. This article reports an intervention research programme in Sao Paulo, Brazil that combines a moral education approach with sustainability awareness in vulnerable communities. The main conceptual foundations of the project, designed to empower the community and promote ethical and environmental awareness are: strengthening the ties between the school and the surrounding community in order to construct 'moral atmosphere'; adoption of Problem- and Project-based Learning and the Design Thinking approach to reach the proposed goals.

rho(0) photoproduction in AuAu collisions at root s(NN)=62.4 GeV measured with the STAR detector

Vector mesons may be photoproduced in relativistic heavy-ion collisions when a virtual photon emitted by one nucleus scatters from the other nucleus, emerging as a vector meson. The STAR Collaboration has previously presented measurements of coherent rho(0) photoproduction at center of mass energies of 130 GeV and 200 GeV in AuAu collisions. Here, we present a measurement of the cross section at 62.4 GeV; we find that the cross section for coherent rho(0) photoproduction with nuclear breakup is 10.5 +/- 1.5 +/- 1.6mb at 62.4 GeV. The cross-section ratio between 200 GeV and 62.4 GeV is 4.4 +/- 0.6, less than is predicted by most theoretical models. It is, however, proportionally much larger than the previously observed 15% +/- 55% increase between 130 GeV and 200 GeV.

Sponges as substrata and early life history of the tubulariid Zyzzyzus warreni (Cnidaria: Hydrozoa) in the Sao Sebastiao Channel, Brazil

The hydroid Zyzzyzus warreni is usually found in shallow coastal waters forming aggregations of solitary polyps embedded in demosponges. Early life history transformations and settlement responses by the actinulae of this hydroid were studied in the laboratory using 13 species of sponges and 2 species of algae collected in the Sao Sebastiao Channel (Brazil) as substrata. The absence of oral tentacles and mouth in the actinulae and early events of metamorphosis suggest that these larvae are unable to spend long periods in the plankton and attach quickly near conspecifics when a preferred substratum is encountered. The time required for settlement and the number of elicited settlings indicated four settlement responses: (a) frequent and short-time settlement, in actinulae exposed to Halichondria cebimarensis, Mycale angulosa, M. aff. americana, M. laxissima (skeleton) and Tedania ignis; (b) moderate and delayed settlement, in actinulae exposed to Aplysina caissara, A. fulva, Haliclona melana and M. microsigmatosa; (c) no settlement, in actinulae exposed to Suberites aurantiacus and to the algae Hypnea musciformis and Sargassum cymosum; and (d) lethal response, in actinulae exposed to Amphimedon viridis, Aplysilla rosea, Dragmacidon reticulatum and M. laxissima. These responses indicate a considerable degree of species discrimination by the actinulae and are consistent with substrata used by the hydroid in the natural environment.

Strangeness Enhancement in Cu-Cu and Au-Au Collisions at root s(NN)=200 GeV

We report new STAR measurements of midrapidity yields for the Lambda, (Lambda) over bar, K-S(0), Xi(-), (Xi) over bar (+), Omega(-), (Omega) over bar (+) particles in Cu + Cu collisions at root s(NN) = 200 GeV, and midrapidity yields for the Lambda, (Lambda) over bar, K-S(0) particles in Au + Au at root s(NN) = 200 GeV. We show that, at a given number of participating nucleons, the production of strange hadrons is higher in Cu + Cu collisions than in Au + Au collisions at the same center-of-mass energy. We find that aspects of the enhancement factors for all particles can be described by a parametrization based on the fraction of participants that undergo multiple collisions.

Comparative neurocranial morphology of angelsharks from the south-western Atlantic Ocean (Chondrichthyes, Elasmobranchii, Squatinidae): implications for taxonomy and phylogeny

Neurocrania of three species of angelsharks from the south-western Atlantic Ocean, occurring off south-eastern and southern Brazil, are described. A detailed morphological description is provided of the neurocranium of Squatina guggenheim and compared with S. argentina and S. occulta. Despite being generally conservative, the neurocranium of Squatina presents significant differences among these species which aid in their identification, which is otherwise problematical. The main distinctions were found in rostral projections, anterior fontanellae, supraorbital crests, upper and lower postorbital processes, otic capsules, suborbital crests, and pterotic processes. Squatina guggenheim and S. occulta share more neurocranial characters when compared to S. argentina. No basal angle was found, but we confirm the presence of a very much reduced and barely noticeable basioccipital fovea in Squatina; systematic implications within elasmobranchs of these and other features are discussed.

SIS: a program to generate draft genome sequence scaffolds for prokaryotes

Background: Decreasing costs of DNA sequencing have made prokaryotic draft genome sequences increasingly common. A contig scaffold is an ordering of contigs in the correct orientation. A scaffold can help genome comparisons and guide gap closure efforts. One popular technique for obtaining contig scaffolds is to map contigs onto a reference genome. However, rearrangements that may exist between the query and reference genomes may result in incorrect scaffolds, if these rearrangements are not taken into account. Large-scale inversions are common rearrangement events in prokaryotic genomes. Even in draft genomes it is possible to detect the presence of inversions given sufficient sequencing coverage and a sufficiently close reference genome. Results: We present a linear-time algorithm that can generate a set of contig scaffolds for a draft genome sequence represented in contigs given a reference genome. The algorithm is aimed at prokaryotic genomes and relies on the presence of matching sequence patterns between the query and reference genomes that can be interpreted as the result of large-scale inversions; we call these patterns inversion signatures. Our algorithm is capable of correctly generating a scaffold if at least one member of every inversion signature pair is present in contigs and no inversion signatures have been overwritten in evolution. The algorithm is also capable of generating scaffolds in the presence of any kind of inversion, even though in this general case there is no guarantee that all scaffolds in the scaffold set will be correct. We compare the performance of SIS, the program that implements the algorithm, to seven other scaffold-generating programs. The results of our tests show that SIS has overall better performance. Conclusions: SIS is a new easy-to-use tool to generate contig scaffolds, available both as stand-alone and as a web server. The good performance of SIS in our tests adds evidence that large-scale inversions are widespread in prokaryotic genomes.