982 resultados para Road work zones
Resumo:
Experimental studies and atomistic simulations have shown that brittle metallic glasses fail by a cavitation mechanism whose origin has been traced to the presence of intrinsic atomic density fluctuations which give rise to weak zones with reduced yield strength. It has been shown recently through continuum analysis that the presence of these zones can lower the cavitation stress considerably under equibiaxial loading. The objective of the present work is to study the effect of the applied stress state on the cavitation behavior of such a heterogeneous plastic solid with distributed weak zones. To this end, 2D plane strain finite element simulations are performed by subjecting a unit cell containing a weak zone to different (biaxiality) stress ratios. The volume fraction and yield strength of the weak zone are varied over a wide range. The results show that unlike in a homogeneous plastic solid, the cavitation stress of the heterogeneous aggregate does not reduce appreciably as the stress ratio decreases from unity when the yield strength of the weak zone is low. It is found that a non-dimensional parameter characterizing the stress state prevailing in the weak zone and its yield properties uniquely control the cavitation stress. The nature of cavitation bifurcation may change from unstable bifurcation to the left at sufficiently low stress ratio to one involving snap cavitation at high stress ratio. (C) 2014 Elsevier Ltd. All rights reserved.
Resumo:
This is a student paper done for a University of California Berkeley Zoology class. Since UCB didn't have its own marine lab at the time, it rented space at Hopkins Marine Station where this work was done. Cadet Hand earned his Ph.D. from Berkeley and went on to become Director of the Bodega Marine Laboratory. Donald Putnam Abbott also earned his Ph.D. from Berkeley and later became a Stanford professor at Hopkins Marine Station. (PDF contains 26 pages)
Resumo:
The analysis of scientific data is integral to materials engineering and science. The correlation between measured variables is often quantified by estimating the coefficient of determination or the r2 value. This is the recognised procedure for determining linear relationships. The authors review the derivation of the r2 value and derive an associated quantity, termed the relative deviation (RD), which is the ratio of the root mean square of the deviations about the fitted line to the root mean square of the deviations about the y bar line expressed as a percentage. The relative deviation has an advantage over the coefficient of determination in that it has greater numerical sensitivity to changes in the spread of data about the fitted line, especially when the scatter is small. In addition, the relative deviation is able to define, in percentage terms, the reduction in scatter when different independent variables are correlated with a common dependent variable. Four case studies in the materials field (aggregate crushing value, Atterberg limits, permeability and creep of asphalt) from work carried out at the Queensland Main Roads Department are presented to show the use of the new parameter RD.
Resumo:
Reality shows are TV programs which represent a format used in television nowadays; however, the observation practices of individual and/or group intimacy dates from thousands years ago. Sometimes this was driven by voyeurism or morbid fascination, some others, by the purpose of guarding, supervising and maintaining status quo. This work offers an alternative answer to the explanation of this type of TV program emergence and relates this appearance to a government procedure bound up with modern State terrorism which began at the end of the eighteenth century and has been recalled by different regimes until present days.
Resumo:
This paper presents the findings of a qualitative research project that explores the experiences and aspirations of disabled young people in Northern Ireland as they make and deal with the transition to adulthood. The study involved young people with disabilities (n=76) in four areas of Northern Ireland, ensuring a geographical spread, an urban/rural mix and representation of both communities. Young people with learning disabilities were included as well as those with physical and/or sensory impairments. This paper focuses on those who were completing job training or work placements and examines the role of such schemes in assisting young people’s transition to adulthood. The research found that many young people had positive experiences of work placement and job training and that social interaction was important to them. Few young people, however, had made the actual transition from work placement or training to ‘real’ employment.
Resumo:
The book considers the question whether the traditional prohibition of nightwork for female manual workers could be defended against EU (then: EEC) discrimination law requirements and against the German constitution itself. While I was working on the PhD, German labour law still prohibited manual workers (but not white collar employees, or nurses, or policewomen) from working nights. Just before the thesis was published, the German constitutional court held that the prohibition indeed violates the Constitution, but that it must not be repealed without providing for specific protection against health risks ensuing from night work. The Court thus mainly confirmed the thesis' results. The thesis first considers the history of the legislation (which was based on an ILO convention), and discusses the social and health risks related to night work. It then comes to the conclusion that gender roles imply that women are at a greater risk when working nights, but that there is no biological justification (except during pregnancy of course). The thesis further develops a recommendation, based on the constitutional welfare states principle and the constitutional protection of health, to not just abolish the prohibition, but to provide uplevel equalisation of working conditions for women and men. This was the first time I also tried to work comparatively (not perfect at all), but I have certainly improved since then. An English summary of the thesis was published in the 3rd issue of the Cardozo Women's Law Journal 1996, which was also my first ever publicatin in English
Resumo:
In order to address road safety effectively, it is essential to understand all the factors, which
attribute to the occurrence of a road collision. This is achieved through road safety
assessment measures, which are primarily based on historical crash data. Recent advances
in uncertain reasoning technology have led to the development of robust machine learning
techniques, which are suitable for investigating road traffic collision data. These techniques
include supervised learning (e.g. SVM) and unsupervised learning (e.g. Cluster Analysis).
This study extends upon previous research work, carried out in Coll et al. [3], which
proposed a non-linear aggregation framework for identifying temporal and spatial hotspots.
The results from Coll et al. [3] identified Lisburn area as the hotspot, in terms of road safety,
in Northern Ireland. This study aims to use Cluster Analysis, to investigate and highlight any
hidden patterns associated with collisions that occurred in Lisburn area, which in turn, will
provide more clarity in the causation factors so that appropriate countermeasures can be put
in place.
Resumo:
Apesar das recentes inovações tecnológicas, o setor dos transportes continua a exercer impactes significativos sobre a economia e o ambiente. Com efeito, o sucesso na redução das emissões neste setor tem sido inferior ao desejável. Isto deve-se a diferentes fatores como a dispersão urbana e a existência de diversos obstáculos à penetração no mercado de tecnologias mais limpas. Consequentemente, a estratégia “Europa 2020” evidencia a necessidade de melhorar a eficiência no uso das atuais infraestruturas rodoviárias. Neste contexto, surge como principal objetivo deste trabalho, a melhoria da compreensão de como uma escolha de rota adequada pode contribuir para a redução de emissões sob diferentes circunstâncias espaciais e temporais. Simultaneamente, pretende-se avaliar diferentes estratégias de gestão de tráfego, nomeadamente o seu potencial ao nível do desempenho e da eficiência energética e ambiental. A integração de métodos empíricos e analíticos para avaliação do impacto de diferentes estratégias de otimização de tráfego nas emissões de CO2 e de poluentes locais constitui uma das principais contribuições deste trabalho. Esta tese divide-se em duas componentes principais. A primeira, predominantemente empírica, baseou-se na utilização de veículos equipados com um dispositivo GPS data logger para recolha de dados de dinâmica de circulação necessários ao cálculo de emissões. Foram percorridos aproximadamente 13200 km em várias rotas com escalas e características distintas: área urbana (Aveiro), área metropolitana (Hampton Roads, VA) e um corredor interurbano (Porto-Aveiro). A segunda parte, predominantemente analítica, baseou-se na aplicação de uma plataforma integrada de simulação de tráfego e emissões. Com base nesta plataforma, foram desenvolvidas funções de desempenho associadas a vários segmentos das redes estudadas, que por sua vez foram aplicadas em modelos de alocação de tráfego. Os resultados de ambas as perspetivas demonstraram que o consumo de combustível e emissões podem ser significativamente minimizados através de escolhas apropriadas de rota e sistemas avançados de gestão de tráfego. Empiricamente demonstrou-se que a seleção de uma rota adequada pode contribuir para uma redução significativa de emissões. Foram identificadas reduções potenciais de emissões de CO2 até 25% e de poluentes locais até 60%. Através da aplicação de modelos de tráfego demonstrou-se que é possível reduzir significativamente os custos ambientais relacionados com o tráfego (até 30%), através da alteração da distribuição dos fluxos ao longo de um corredor com quatro rotas alternativas. Contudo, apesar dos resultados positivos relativamente ao potencial para a redução de emissões com base em seleções de rotas adequadas, foram identificadas algumas situações de compromisso e/ou condicionantes que devem ser consideradas em futuros sistemas de eco navegação. Entre essas condicionantes importa salientar que: i) a minimização de diferentes poluentes pode implicar diferentes estratégias de navegação, ii) a minimização da emissão de poluentes, frequentemente envolve a escolha de rotas urbanas (em áreas densamente povoadas), iii) para níveis mais elevados de penetração de dispositivos de eco-navegação, os impactos ambientais em todo o sistema podem ser maiores do que se os condutores fossem orientados por dispositivos tradicionais focados na minimização do tempo de viagem. Com este trabalho demonstrou-se que as estratégias de gestão de tráfego com o intuito da minimização das emissões de CO2 são compatíveis com a minimização do tempo de viagem. Por outro lado, a minimização de poluentes locais pode levar a um aumento considerável do tempo de viagem. No entanto, dada a tendência de redução nos fatores de emissão dos poluentes locais, é expectável que estes objetivos contraditórios tendam a ser minimizados a médio prazo. Afigura-se um elevado potencial de aplicação da metodologia desenvolvida, seja através da utilização de dispositivos móveis, sistemas de comunicação entre infraestruturas e veículos e outros sistemas avançados de gestão de tráfego.
Resumo:
The selection of the energy source to power the transport sector is one of the main current concerns, not only relative with the energy paradigm but also due to the strong influence of road traffic in urban areas, which highly affects human exposure to air pollutants and human health and quality of life. Due to current important technical limitations of advanced energy sources for transportation purposes, biofuels are seen as an alternative way to power the world’s motor vehicles in a near-future, helping to reduce GHG emissions while at the same time stimulating rural development. Motivated by European strategies, Portugal, has been betting on biofuels to meet the Directive 2009/28/CE goals for road transports using biofuels, especially biodiesel, even though, there is unawareness regarding its impacts on air quality. In this sense, this work intends to clarify this issue by trying to answer the following question: can biodiesel use contribute to a better air quality over Portugal, particularly over urban areas? The first step of this work consisted on the characterization of the national biodiesel supply chain, which allows verifying that the biodiesel chain has problems of sustainability as it depends on raw materials importation, therefore not contributing to reduce the external energy dependence. Next, atmospheric pollutant emissions and air quality impacts associated to the biodiesel use on road transports were assessed, over Portugal and in particular over the Porto urban area, making use of the WRF-EURAD mesoscale numerical modelling system. For that, two emission scenarios were defined: a reference situation without biodiesel use and a scenario reflecting the use of a B20 fuel. Through the comparison of both scenarios, it was verified that the use of B20 fuels helps in controlling air pollution, promoting reductions on PM10, PM2.5, CO and total NMVOC concentrations. It was also verified that NO2 concentrations decrease over the mainland Portugal, but increase in the Porto urban area, as well as formaldehyde, acetaldehyde and acrolein emissions in the both case studies. However, the use of pure diesel is more injurious for human health due to its dominant VOC which have higher chronic hazard quotients and hazard indices when compared to B20.
Resumo:
London's air quality has improved over recent decades, but is still the worst in the UK. Road transport emissions play an important part in this pollution. A low emission zone (LEZ) would help to accelerate the introduction of cleaner vehicles, and reduce the number of older, more polluting vehicles operating in London. Survey results indicate that there is some support among goods vehicle operators for a LEZ in London, depending on the precise scheme definition. Operators would generally try to comply with LEZ regulations, with most companies either using technical approaches to ensure that their London vehicle fleet complied with the required emission standard, or redeploying vehicles with the appropriate emission standard from other locations.
Resumo:
LGVs are of ever-greater importance in terms of the final delivery of many time-critical, high value goods and are also widely used in industries that provide a wide range of critical support services. There are almost five times as many LGVs as there are HGVs (goods vehicles over 3.5 tonnes gross vehicle weight) currently licensed in Britain. The LGV fleet in Britain is growing at a faster rate than the HGV fleet, and the LGV fleet travels more than twice as many vehicle kilometres each year than the total HGV fleet. LGVs perform a far greater proportion of their total distance travelled in urban areas than HGVs, and consume 25% of the total diesel and 3% of the total petrol used by all motorised road transport vehicles in Britain.
Resumo:
The review illustrates the importance of road movements in goods distribution in urban areas. It highlights the major economic, environmental and social impacts associated with this freight activity and reviews policy options available to those responsible for regulation. A wide range of possible solutions to problems posed by urban freight operations are also covered including approaches related to: consolidation, facilities, vehicle design, information capture and utilisation, and non-road modes.
Resumo:
Hard‐rock watersheds commonly exhibit complex geological bedrock and morphological features. Hydromineral resources have relevant economic value for the thermal spas industry. The present study aims to develop a groundwater vulnerability approach in Caldas da Cavaca hydromineral system (Aguiar da Beira, Central Portugal) which has a thermal tradition that dates back to the late 19th century, and contribute to a better understanding of the hydrogeological conceptual site model. In this work different layers were overlaid, generating several thematic maps to arrive at an integrated framework of several key‐sectors in Caldas da Cavaca site. Thus, to accomplish a comprehensive analysis and conceptualization of the site, a multi‐technical approach was used, such as, field and laboratory techniques, where several data was collected, like geotectonics, hydrology and hydrogeology, hydrogeomorphology, hydrogeophysical and hydrogeomechanical zoning aiming the application of the so‐called DISCO method. All these techniques were successfully performed and a groundwater vulnerability to contamination assessment, based on GOD‐S, DRASTIC‐Fm, SINTACS, SI and DISCO indexes methodology, was delineated. Geographical Information Systems (GIS) technology was on the basis to organise and integrate the geodatabases and to produce all the thematic maps. This multi‐technical approach highlights the importance of groundwater vulnerability to contamination mapping as a tool to support hydrogeological conceptualisation, contributing to better decision‐making of water resources management and sustainability.
Resumo:
A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics
Resumo:
The second half of the XX century was marked by a great increase in the number of people living in cities. Urban agglomerations became poles of attraction for migration flows and these phenomena, coupled with growing car-ownership rates, resulted in the fact that modern transport systems are characterized by large number of users and traffic modes. The necessity to organize these complex systems and to provide space for different traffic modes changed the way cities look. Urban areas had to cope with traffic flows, and as a result nowadays typical street pattern consists of a road for motorized vehicles, a cycle lane (in some cases), pavement for pedestrians, parking and a range of crucial signage to facilitate navigation and make mobility more secure. However, this type of street organization may not be desirable in certain areas, more specifically, in the city centers. Downtown areas have always been places where economic, leisure, social and other types of facilities are concentrated, not surprisingly, they often attract large number of people and this frequently results in traffic jams, air and noise pollution, thus creating unpleasant environment. Besides, excessive traffic signage in central locations can harm the image and perception of a place, this relates in particular to historical centers with architectural heritage.