Comparison of nitrogen adsorption at 77 K on non-porous silica and pore wall of MCM-41 materials by means of density functional theory

Nitrogen adsorption on a surface of a non-porous reference material is widely used in the characterization. Traditionally, the enhancement of solid-fluid potential in a porous solid is accounted for by incorporating the surface curvature into the solid-fluid Potential of the flat reference surface. However, this calculation procedure has not been justified experimentally. In this paper, we derive the solid-fluid potential of mesoporous MCM-41 solid by using solely the adsorption isotherm of that solid. This solid-fluid potential is then compared with that of the non-porous reference surface. In derivation of the solid-fluid potential for both reference surface and mesoporous MCM-41 silica (diameter ranging front 3 to 6.5 nm) we employ the nonlocal density functional theory developed for amorphous solids. It is found that, to out, surprise, the solid-fluid potential of a porous solid is practically the same as that for the reference surface, indicating that there is no enhancement due to Surface curvature. This requires further investigations to explain this unusual departure from our conventional wisdom of curvature-induced enhancement. Accepting the curvature-independent solid-fluid potential derived from the non-porous reference surface, we analyze the hysteresis features of a series of MCM-41 samples. (c) 2005 Elsevier Inc. All rights reserved.

Preparação, caracterização e modificação de adsorventes para remoção de pesticidas de águas

O objectivo principal deste trabalho de mestrado consistiu em avaliar a potencial utilização de materiais adsorventes, nomeadamente, de carvões activados (AC) preparados por activação química com KOH, a partir de PET reciclado, e de materiais com estrutura mesoporosa ordenada, do tipo MCM-41 e SBA-15, na remoção de ácido 4 - cloro - 2 - metilfenoxiacético (MCPA) e de azul de metileno (MB), presentes nas águas. Nesta tese apresentam-se estudos de preparação e caracterização de materiais micro e mesoporosos e também estudos de avaliação da capacidade adsortiva em fase líquida. Prepararam-se três materiais microporosos, nomeadamente, PET-2-700, PET-2-700ox (AC oxidado) e PET-2-700red (AC reduzido), dois materiais constituídos exclusivamente por mesoporos, Si-MCM-41 e Ti-MCM-41-50 e dois materiais contendo maioritariamente mesoporos, mas que também possuem alguma microporosidade, tais corno, Si-SBA-15 e Ti-SBA-15-50. A caracterização textural dos adsorventes foi inferida por adsorção de azoto a 77K e por de difracção de raios X. Recorreu-se a três métodos de análise das isotérmicas, nomeadamente, Dubinin-Radushkevich, Brunauer-Ernrnett-Teller e alfa-s (as). A caracterização química dos AC foi realizada recorrendo-se a técnicas de análise elementar (AE) e espectroscopia de infravermelho com transformadas de Fourier (FTIR) e à determinação do ponto de carga zero. Os três carvões activados possuem valores de área superficial externa idênticos, o PET-2-700 possui o maior volume microporoso e o PET-2-700ox exibe o maior diâmetro de poros. Por outro lado, o PET-2-700ox possui um carácter fortemente ácido, o PET-2-700 exibe carácter ligeiramente ácido e o PET-2-700red apresenta propriedades ligeiramente alcalinas. Com base na AE, todas as amostras possuem percentagens de carbono elevadas, sendo que o PET-2-700red apresenta o valor mais elevado. Os resultados obtidos para a caracterização estrutural dos revelaram a obtenção de materiais mesoporosos de alta qualidade, definida pela elevada regularidade e uniformidade da estrutura porosa. A análise dos parâmetros de caracterização textura! permitiu inferir que os quatro materiais mesoporosos possuem valores de área superficial elevados, e que os materiais SBA-15 apresentam valores de volume poroso total e de tamanho de poros superiores aos manifestados pelos MCM-41. A incorporação de titânio não conduziu a uma perda significativa de qualidade dos materiais substituídos em relação às correspondentes amostras de sílica. Efectuaram-se estudos de adsorção em fase líquida de forma a avaliar a possível aplicação dos vários adsorventes na remoção de MCPA e de MB de efluentes líquidos. concluiu-se que o tempo de equilíbrio de 72 horas seria adequado e que a capacidade de adsorção dos vários AC era superior em meio ácido. Com base nas isotérmicas de adsorção do MCPA e do MB e na aplicação da representação de Langmuir e de Freundlich, foi possível concluir que o PET-2-700 possui a maior capacidade de adsorção do MCPA, 1.42 mmol/g, enquanto que o PET-2-700ox revelou a maior capacidade de adsorção do MB, 1.43 mmol/g. Na realidade, os materiais microporosos estudados apresentaram percentagens de remoção elevadas, tanto do MCPA como do MB. Relativamente aos materiais mesoporosos ordenados preparados neste trabalho, a percentagem de remoção de para os poluentes em estudo foi relativamente baixa, constatando-se que nesta fase dos estudos não constituem uma alternativa viável à utilização dos AC. No entanto, uma funcionalização criteriosa dos mesmos pode eventualmente proporcionar um aumento da capacidade adsortiva. ABSTRACT: The work presented in this master thesis, consisted of evaluating the potential use of different adsorbents materials, like activated carbon (AC) prepared by chemical activation with KOH, from recycled poly (ethylene terephthalate) (PET) and materials with ordered mesoporous structure such as MCM-41 and SBA-15, for removing acid 4-chlorine-2-metilfenoxiacétic and methylene blue from aqueous phase. We had prepared three microporous materials, PET-200-700, PET-2-700ox (AC oxidized) and PET-2-700red (reduced AC), two materials consisting exclusively of mesopores, Si-MCM-41 and Ti-MCM-41-50 and two materials containing mainly mesopores, but also having some microporosity, such as Si-SBA-15 and Ti-SBA-15-50. The textural characterization of the adsorbents was inferred by nitrogen adsorption at 77K and X-ray diffraction. Three methods were used to analyse the isotherms, namely, Dubinin-Radushkevich, Brunauer-Emmett-Teller and alpha-s (as). The chemical characterization of AC was performed using the elementary analysis, Fourier transform infrared spectroscopy (FTIR) and determination of the point of zero charge. Concerning the AC, the three present almost the same externa! surface area, PET-2-700 has a high micropore volume and PET-2-700ox shows the largest pore size diameter. On the other hand, PET-2-700ox had a strong acid character, PET-2-700 exhibits just a slightly acid character and PET-2-700red presents alkaline properties. The AE analysis allows confirming the high carbon content of theses AC, with PET-2-700red exhibiting the highest carbon proportion. The results from the structural characterization of the mesoporous materials, had disclosed the attainment of materials with high quality, defined by the raised regularity and uniformity of the porous structure. The analysis of the textural parameters allowed inferring that the four studied mesoporous materials possess high superficial area. The SBA-15 type materials present higher values of total porous volume and pores size diameter as the MCM-41. Also, the titanium incorporation did not lead to a significant loss of quality of the materials substituted in relation to the corresponding silica samples. The adsorption studies in liquid phase allow evaluating the possibility of using the different adsorbents for the MCPA and the MB removal. The kinetic studies had allowed to state the equilibrium time as 72 hours and a higher adsorption capacity was achieved in an acid medium. The influence of the pH of the medium, on the MCPA adsorption was evaluated. The MCPA and MB isotherms were analysed based on the Langmuir and Freundlich equation, the representations presented an excellent linearity, indicating the applicability of these equations to these systems. Also, it allows concluded that PET-2-700 had a higher adsorption capacity for MCPA, 1.42 mmol/g, and PET-2-700ox had a higher adsorption capacity for MB, 1.43 mmol/g. The AC used presented high removal percentages for MCPA and MB. Concerning the mesoporous materials prepared in this work, the percentage removal for the pollutants in study was relatively low, and evidencing that at the moment these mesoporous materials do not constitute a viable alternative to the AC. However, an astute funcionalisation of the same ones can, eventually provide an increase of the adsorption capacity.

Characterization of thiol-functionalised silica films deposited on electrode surfaces

Thiol-functionalised silica films were deposited on various electrode surfaces (gold, platinum, glassy carbon) by spin-coating sol-gel mixtures in the presence of a surfactant template. Film formation occurred by evaporation induced self-assembly (EISA) involving the hydrolysis and (co)condensation of silane and organosilane precursors on the electrode surface. The characterization of such material was performed by IR spectroscopy, thermogravimetry (TG), elemental analysis (EA), atomic force microscopy (AFM), scanning electron microscopy (SEM) and cyclic voltammetry (CV).

Characterization of dynamic solid phase DNA extraction from blood with magnetically controlled silica beads

A novel solid phase extraction technique is described where DNA is bound and eluted from magnetic silica beads in a manner where efficiency is dependent on the magnetic manipulation of the beads and not on the flow of solution through a packed bed. The utility of this technique in the isolation of reasonably pure, PCR-amplifiable DNA from complex samples is shown by isolating DNA from whole human blood, and subsequently amplifying a fragment of the beta-globin gene. By effectively controlling the movement of the solid phase in the presence of a static sample, the issues associated with reproducibly packing a solid phase in a microchannel and maintaining consistent flow rates are eliminated. The technique described here is rapid, simple, and efficient, allowing for recovery of more than 60% of DNA from 0.6 mu L of blood at a concentration which is suitable for PCR amplification. In addition, the technique presented here requires inexpensive, common laboratory equipment, making it easily adopted for both clinical point-of-care applications and on-site forensic sample analysis.

Production, characterization and application of activated carbon from brewer`s spent grain lignin

Different types of activated carbon were prepared by chemical activation of brewer`s spent grain (BSG) lignin using H(3)PO(4) at various acid/lignin ratios (1, 2, or 3 g/g) and carbonization temperatures (300, 450, or 600 degrees C), according to a 2(2) full-factorial design. The resulting materials were characterized with regard to their surface area, pore volume, and pore size distribution, and used for detoxification of BSG hemicellulosic hydrolysate (a mixture of sugars, phenolic compounds, metallic ions, among other compounds). BSG carbons presented BET surface areas between 33 and 692 m(2)/g, and micro- and mesopores with volumes between 0.058 and 0.453 cm(3)/g. The carbons showed high capacity for adsorption of metallic ions, mainly nickel, iron, chromium, and silicon. The concentration of phenolic compounds and color were also reduced by these sorbents. These results suggest that activated carbons with characteristics similar to those commercially found and high adsorption capacity can be produced from BSG lignin. (C) 2009 Elsevier Ltd. All rights reserved.

Mechanical properties, drying and autogenous shrinkage of blast furnace slag activated with hydrated lime and gypsum

This article reports the characteristics of blast furnace slag (BFS) pastes activated with hydrated lime (5%) and hydrated lime (2%) plus gypsum (6%) in relation to compressive strength, shrinkage (autogenous and drying) and microstructure (porosity, hydrated products). The paste mixtures were characterized using powder X-ray diffraction (XRD), mercury intrusion porosimetry (MIP) and thermogravimetric analysis (TG/DTG). BSF activated with lime and gypsum (LG) results in larger amounts of ettringite when compared with BFS activated with lime (L). Although the porosities of the L and LG mixtures were about the same, there was a greater pore refinement for the BFS activated with lime, with an increase in mesopores volume with age. The presence of ettringite and the higher volumes of macropores cause the compressive strength of BSF activated with hydrated lime plus gypsum to be smaller than that of BFS activated with lime. For both chemical activators, compressive strength developed slowly at early ages. Autogenous and drying shrinkage were greater for the BFS activated with lime, believed to result from the more refined porous structure in comparison with the mixture activated with gypsum plus lime. (c) 2010 Elsevier Ltd. All rights reserved.

Biogenic modified silica as a sorbent of cadmium ions: Preparation and characterization

This work describes the preparation and characterization of biogenic modified silica from rice hull ash and its use as a sorbent of cadmium ions. Thus, an agro-industrial residue has been used to produce a new adsorbent product which is able to remove toxic elements. Mesoporous biogenic silica was obtained by alkaline extraction of sodium silicate by hydrolysis with the sol-gel process, and it was modified with salen using 1,2-dichloroethane as a spacer. The surface area of the silica was measured by nitrogen adsorption/desorption analysis. Surface modification was measured by Fourier transform infrared spectroscopy. The degree of functionalization was obtained by elemental analysis. This work showed that biogenic modified silica can be produced in aqueous media from rice hull ash using a simple method, providing an alternative method for adsorbent preparation. Thermogravimetric analysis showed that the salen-modified silica is stable up to 209 C. The modified silica displays appropriate structural characteristics for an adsorbent. The cylindrical pores, open at both ends, allow free diffusion of cadmium ions to the adsorption sites on the silica surface. The surface modification increases cadmium adsorption on the silica surface 100-fold. The salen-modified silica showed specific adsorption for Cd2+ of 44.52 mg/g SiO2 at cadmium concentration of 100 mg/l.

DSC estimation of structural and textural parameters of SBA-15 silica using water probe

The aim of this study was to use DSC and X-ray diffraction measurements to determine the pore size and pore wall thickness of highly ordered SBA-15 materials. The DSC curves showed two endothermic events during the heating cycle. These events were due to the presence of water inside and outside of mesopores. The results of pore radius, wall thickness and pore volume measurements were in good agreement with the results obtained by nitrogen adsorption measurement, XRD and transmission electron microscopy.

Capillary coexistence and criticality in mesopores: Modification of the Kelvin theory

The classical model of capillary equilibrium in cylindrical pores is modified here by the introduction of molecular concepts and the solid fluid interaction potential. The new approach accurately predicts capillary coexistence and criticality, with results quantitatively matching those from density functional theory for nitrogen adsorption, while also predicting condensation pressures in agreement with reported experimental findings for MCM-41. The larger critical pore size for nitrogen adsorption in these materials, however, suggests a modification of the potential function parameters, evaluated here from data for hydroxylated silica.

Thickness and stability of adsorbed film in cylindrical mesopores

The adsorbed film in small cylindrical mesopores is studied by using MCM-41 samples of uniform cylindrical channels as model systems. It is found that at a given relative pressure, the smaller the pore radius, the thicker the adsorbed film is, as postulated by Broekhoff and De Beer. Thermodynamics analysis established that the stability of the adsorbed film is determined by interface curvature and the potential of interaction between adsorbate and adsorbent. A semiempirical equation is proposed to describe the state of stable adsorbed films in cylindrical mesopores. It is also shown to be useful in calculations of pore size distributions of mesoporous solids.

Characterization of pore wall heterogeneity in nanoporous carbons using adsorption: the slit pore model revisited

In this paper, we propose a new nonlocal density functional theory characterization procedure, the finite wall thickness model, for nanoporous carbons, whereby heterogeneity of pore size and pore walls in the carbon is probed simultaneously. We determine the pore size distributions and pore wall thickness distributions of several commercial activated carbons and coal chars, with good correspondence with X-ray diffraction. It is shown that the conventional infinite wall thickness approach overestimates the pore size slightly. Pore-pore correlation has been shown to have a negligible effect on prediction of pore size and pore wall thickness distributions for small molecules such as argon used in characterization. By utilizing the structural parameters (pore size and pore wall thickness distribution) in the generalized adsorption isotherm (GAI) we are able to predict adsorption uptake of supercritical gases in BPL and Norit RI Extra carbons, in excellent agreement with experimental adsorption uptake data up to 60 MPa. The method offers a useful technique for probing features of the solid skeleton, hitherto studied by crystallographic methods.

XAS characterization of the RuO(2)-Ta(2)O(5) system local (crystal) structure

The influence of the preparation method on the structural properties of the RuO(2)-Ta(2)O(5) system was investigated. Both thin films on Ti substrates and powder samples of nominal composition Ti/RuO(2)-Ta(2)O(5) (Ru:Ta = 100:0, 90:10, 80:20, 30:70, and 0:100 at.%) were prepared through thermal decomposition of polymeric precursors (DPP). The thin films and powder samples were investigated using X-ray absorption spectroscopy (XAS). XANES analyses showed that Ru and Ta are present in the Ru(IV) and Ta(V) oxidation states. EXAFS signals of all the samples were analyzed, to obtain the average bond length (r), coordination number, and the Debye-Waller factor (sigma(2)) for each Ru-O, Ru-Ru, Ta-O nearest-neighbor. The first shell Ru-O distance was found at 1.91-1.92 angstrom with coordination number of 1.8-2.1, and at 2.01-2.02 angstrom with coordination number of 3.9-4.1. The Ta-O distance obtained for all the samples and in both modes (transmission and fluorescence) had significantly different values from the theoretical ones. The results revealed that the local structure around both the Ru and Ta sites are similar, and that they consist of distorted M-O(6) octahedra (where M = Ru or Ta). (C) 2010 Elsevier B.V. All rights reserved.

Biophysical characterization of interactions involving importin-alpha during nuclear import

Proteins containing the classical nuclear localization sequences (NLSs) are imported into the nucleus by the importin-alpha/beta heterodimer. Importin-alpha contains the NLS binding site, whereas importin-beta mediates the translocation through the nuclear pore. We characterized the interactions involving importin-alpha during nuclear import using a combination of biophysical techniques (biosensor, crystallography, sedimentation equilibrium, electrophoresis, and circular dichroism). Importin-alpha is shown to exist in a monomeric autoinhibited state (association with NLSs undetectable by biosensor). Association with importin-beta (stoichiometry, 1:1; K-D = 1.1 x 10(-8) m) increases the affinity for NLSs; the importin-alpha/beta complex binds representative monopartite NLS (simian virus 40 large T-antigen) and bipartite NLS (nucleoplasmin) with affinities (K-D = 3.5 x 10(-8) m and 4.8 x 10(-8) m, respectively) comparable with those of a truncated importin-alpha lacking the autoinhibitory domain (T-antigen NLS, K-D = 1.7 x 10(-8) m; nucleoplasmin NLS, K-D = 1.4 x 10(-8) m). The autoinhibitory domain (as a separate peptide) binds the truncated importin-alpha, and the crystal structure of the complex resembles the structure of full-length importin-alpha. Our results support the model of regulation of nuclear import mediated by the intrasteric autoregulatory sequence of importin-alpha and provide a quantitative description of the binding and regulatory steps during nuclear import.

Recent advances in processing and characterization of periodic mesoporous MCM-41 silicate molecular sieves

The discovery of periodic mesoporous MCM-41 and related molecular sieves has attracted significant attention from a fundamental as well as applied perspective. They possess well-defined cylindrical/hexagonal mesopores with a simple geometry, tailored pore size, and reproducible surface properties. Hence, there is an ever-growing scientific interest in the challenges posed by their processing and characterization and by the refinement of various sorption models. Further, MCM-41-based materials are currently under intense investigation with respect to their utility as adsorbents, catalysts, supports, ion-exchangers, and molecular hosts. In this article, we provide a critical review of the developments in these areas with particular emphasis on adsorption characteristics, progress in controlling the pore sizes, and a comparison of pore size distributions using traditional and newer models. The model proposed by the authors for adsorption isotherms and criticalities in capillary condensation and hysteresis is found to explain unusual adsorption behavior in these materials while providing a convenient characterization tool.

A generalised dynamic model for char particle gasification with structure evolution and peripheral fragmentation

A generalised model for the prediction of single char particle gasification dynamics, accounting for multi-component mass transfer with chemical reaction, heat transfer, as well as structure evolution and peripheral fragmentation is developed in this paper. Maxwell-Stefan analysis is uniquely applied to both micro and macropores within the framework of the dusty-gas model to account for the bidisperse nature of the char, which differs significantly from the conventional models that are based on a single pore type. The peripheral fragmentation and random-pore correlation incorporated into the model enable prediction of structure/reactivity relationships. The occurrence of chemical reaction within the boundary layer reported by Biggs and Agarwal (Chem. Eng. Sci. 52 (1997) 941) has been confirmed through an analysis of CO/CO2 product ratio obtained from model simulations. However, it is also quantitatively observed that the significance of boundary layer reaction reduces notably with the reduction of oxygen concentration in the flue gas, operational pressure and film thickness. Computations have also shown that in the presence of diffusional gradients peripheral fragmentation occurs in the early stages on the surface, after which conversion quickens significantly due to small particle size. Results of the early commencement of peripheral fragmentation at relatively low overall conversion obtained from a large number of simulations agree well with experimental observations reported by Feng and Bhatia (Energy & Fuels 14 (2000) 297). Comprehensive analysis of simulation results is carried out based on well accepted physical principles to rationalise model prediction. (C) 2001 Elsevier Science Ltd. AH rights reserved.