Azospirillum lipoferum tRNAs: Fractionation and identification of tRNA species and the nucleotide sequence of tRNA(Asn) (QUU)

Transfer RNAs of Azospirillum lipoferum were separated by two- dimensional gel electrophoresis and identified by aminoacylation. Thirty-six tRNA spots were resolved by this technique and twenty-six tRNA species have been identified. There are five tRNAs for Leu, four for Val, three for Pro, two each for Arg, Ile, Lys and Tyr, and one each for Ala, Asp, His, Phe, Ser and Thr. The tRNA(Asn) (QUU) was purified and its nucleotide sequence was determined. The A. lipoferum tRNA(Asn) (QUU) is 92% similar to B. subtilis tRNA(Asn) gene and two hypermodified nucleosides, queuosine (Q) and N-(9-beta-D Ribofuranosylpurine-6-YL) carbamoyl)-threonine (t(6)A) are present in this tRNA.

Is there a role for microsampling in antibiotic pharmacokinetic studies?

- Introduction Clinical pharmacokinetic studies of antibiotics can establish evidence-based dosing regimens that improve the likelihood of eradicating the pathogen at the site of infection, reduce the potential for selection of resistant pathogens, and minimize harm to the patient. Innovations in small volume sampling (< 50 μL) or ‘microsampling’ may result in less-invasive sample collection, self-sampling and dried storage. Microsampling may open up opportunities in patient groups where sampling is challenging. - Areas Covered The challenges for implementation of microsampling to assure suitability of the results, include: acceptable study design, regulatory agency acceptance, and meeting bioanalytical validation requirements. This manuscript covers various microsampling methods, including dried blood/plasma spots, volumetric absorptive microsampling, capillary microsampling, plasma preparation technologies and solid-phase microextraction. - Expert Opinion The available analytical technology is being underutilized due to a lack of bridging studies and validated bioanalytical methods. These deficiencies represent major impediments to the application of microsampling to antibiotic pharmacokinetic studies. A conceptual framework for the assessment of the suitability of microsampling in clinical pharmacokinetic studies of antibiotics is provided. This model establishes a ‘contingency approach’ with consideration of the antibiotic and the type and location of the patient, as well as the more prescriptive bioanalytical validation protocols.

Multiple excitation nano-spot generation and confocal detection for far-field microscopy

An imaging technique is developed for the controlled generation of multiple excitation nano-spots for far-field microscopy. The system point spread function (PSF) is obtained by interfering two counter-propagating extended depth-of-focus PSF (DoF-PSF), resulting in highly localized multiple excitation spots along the optical axis. The technique permits (1) simultaneous excitation of multiple planes in the specimen; (2) control of the number of spots by confocal detection; and (3) overcoming the point-by-point based excitation. Fluorescence detection from the excitation spots can be efficiently achieved by Z-scanning the detector/pinhole assembly. The technique complements most of the bioimaging techniques and may find potential application in high resolution fluorescence microscopy and nanoscale imaging.

From environmental concerns towards sustainable food provisioning. : Material flow and food consumption scenario studies on sustainability of agri-food systems

Agriculture is an economic activity that heavily relies on the availability of natural resources. Through its role in food production agriculture is a major factor affecting public welfare and health, and its indirect contribution to gross domestic product and employment is significant. Agriculture also contributes to numerous ecosystem services through management of rural areas. However, the environmental impact of agriculture is considerable and reaches far beyond the agroecosystems. The questions related to farming for food production are, thus, manifold and of great public concern. Improving environmental performance of agriculture and sustainability of food production, sustainabilizing food production, calls for application of wide range of expertise knowledge. This study falls within the field of agro-ecology, with interphases to food systems and sustainability research and exploits the methods typical of industrial ecology. The research in these fields extends from multidisciplinary to interdisciplinary and transdisciplinary, a holistic approach being the key tenet. The methods of industrial ecology have been applied extensively to explore the interaction between human economic activity and resource use. Specifically, the material flow approach (MFA) has established its position through application of systematic environmental and economic accounting statistics. However, very few studies have applied MFA specifically to agriculture. The MFA approach was used in this thesis in such a context in Finland. The focus of this study is the ecological sustainability of primary production. The aim was to explore the possibilities of assessing ecological sustainability of agriculture by using two different approaches. In the first approach the MFA-methods from industrial ecology were applied to agriculture, whereas the other is based on the food consumption scenarios. The two approaches were used in order to capture some of the impacts of dietary changes and of changes in production mode on the environment. The methods were applied at levels ranging from national to sector and local levels. Through the supply-demand approach, the viewpoint changed between that of food production to that of food consumption. The main data sources were official statistics complemented with published research results and expertise appraisals. MFA approach was used to define the system boundaries, to quantify the material flows and to construct eco-efficiency indicators for agriculture. The results were further elaborated for an input-output model that was used to analyse the food flux in Finland and to determine its relationship to the economy-wide physical and monetary flows. The methods based on food consumption scenarios were applied at regional and local level for assessing feasibility and environmental impacts of relocalising food production. The approach was also used for quantification and source allocation of greenhouse gas (GHG) emissions of primary production. GHG assessment provided, thus, a means of crosschecking the results obtained by using the two different approaches. MFA data as such or expressed as eco-efficiency indicators, are useful in describing the overall development. However, the data are not sufficiently detailed for identifying the hot spots of environmental sustainability. Eco-efficiency indicators should not be bluntly used in environmental assessment: the carrying capacity of the nature, the potential exhaustion of non-renewable natural resources and the possible rebound effect need also to be accounted for when striving towards improved eco-efficiency. The input-output model is suitable for nationwide economy analyses and it shows the distribution of monetary and material flows among the various sectors. Environmental impact can be captured only at a very general level in terms of total material requirement, gaseous emissions, energy consumption and agricultural land use. Improving environmental performance of food production requires more detailed and more local information. The approach based on food consumption scenarios can be applied at regional or local scales. Based on various diet options the method accounts for the feasibility of re-localising food production and environmental impacts of such re-localisation in terms of nutrient balances, gaseous emissions, agricultural energy consumption, agricultural land use and diversity of crop cultivation. The approach is applicable anywhere, but the calculation parameters need to be adjusted so as to comply with the specific circumstances. The food consumption scenario approach, thus, pays attention to the variability of production circumstances, and may provide some environmental information that is locally relevant. The approaches based on the input-output model and on food consumption scenarios represent small steps towards more holistic systemic thinking. However, neither one alone nor the two together provide sufficient information for sustainabilizing food production. Environmental performance of food production should be assessed together with the other criteria of sustainable food provisioning. This requires evaluation and integration of research results from many different disciplines in the context of a specified geographic area. Foodshed area that comprises both the rural hinterlands of food production and the population centres of food consumption is suggested to represent a suitable areal extent for such research. Finding a balance between the various aspects of sustainability is a matter of optimal trade-off. The balance cannot be universally determined, but the assessment methods and the actual measures depend on what the bottlenecks of sustainability are in the area concerned. These have to be agreed upon among the actors of the area

Chain of excitation spot generation by aperture engineering

An optical technique is proposed for obtaining multiple excitation spots. Phase-matched counter propagating extended depth-of-focus fields were superimposed along the optical axis for generating multiple localized excitation spots. Moreover, the filtering effect due to the optical mask increases the lateral resolution. Proposed technique introduces the concept of simultaneous multiplane excitation and improves three-dimensional resolution. (C) 2010 American Institute of Physics.

Primary Structural Documentation of the Major Urinary Protein of the Indian Commensal Rat (Rattus rattus) Using a Proteomics Platform

Purpose: A number of proteome studies have been performed recently to identify pheromone-related protein expression and their molecular function using genetically modified rodents' urine. However, no such studies have used Indian commensal rodents; interestingly, in a previous investigation, we confirmed the presence of volatile molecules in commensal rodents urine and these molecules seem to be actively involved in pheromonal communication. Therefore, the present study aims to identify the major urinary protein [MUP] present in commensal rat urine, which will help us to understand the protein's expression pattern and intrinsic properties among the rodents globally. Experimental Design: Initially, the total urinary proteins were separated by 1-D and 2-D electrophoresis and then subsequently analyzed by Matrix Assisted Laser Desorption Ionization-Time of Flight and Mass Spectrometer (MALDI-TOF/MS). Furthermore, they were then fragmented with the aid of a Tandem Mass Spectrometer (TOF/TOF) and the identified sequences aligned and confirmed using similarity with the deduced primary structures of members of the lipocalin superfamily.Results: The SDS-PAGE protein profiles showed distinct proteins with molecular masses of 15, 22.4, 25, 28, 42, 50, 55, 68, and 91 kDa. Of these proteins, the 22.4 kDa protein was considered to be target candidate. When 2D electrophoresis was carried out, about similar to 50 spots were detected with different masses and various pI ranges. The 22.4 kDa protein was found to have a pI of about 4.9. This 22.4 kDa protein spot was digested and subjected to mass spectrometry; it was identified as rat MUP. The fragmented peptides from the rat MUP at 935, 1026, 1192, and 1303 m/z were further fragmented with the aid of MS/MS and generated de novo sequence and this confirmed this protein to be the MUP present in the urine of commensal rats.Conclusion: The present investigation confirms the presence of MUP with a molecular mass of 22.4 kDa in the urine of commensal rats. This protein may be involved in the binding of volatile molecules and opens up a discussion about how volatile and non-volatile molecules in the commensal rats' urine may contribute chemo-communication.

Synthesis and structural aspects of quasicrystals in Mg-Al-Ag system: Mg4Al6Ag

The existence of an icosahedral phase in Mg−Al−Ag is better understood on a crystallographic basis rather than on a quantum structural diagram basis. The quasicrystalline structure is delineated in terms of quasiperiodic arrangement of Pauling triacontahedra, which can be identified in the equilibrium structure. Subtle differences in the electron diffraction patterns have been recorded compared to the ideal quasicrystalline pattern. The misalignment of spots and distortions are better attributed to higher order rational approximate structure than anisotropic phason strain. Ares of diffuse intensity have been related to the ordering among the atoms in the clusters.

Direct numerical simulation of autoignition in a non-premixed, turbulent medium

In this paper, direct numerical simulation of autoignition in an initially non-premixed medium under isotropic, homogeneous, and decaying turbulence is presented. The pressure-based method developed herein is a spectral implementation of the sequential steps followed in the predictor-corrector type of algorithms; it includes the effects of density fluctuations caused by spatial inhomogeneities ill temperature and species. The velocity and pressure field are solved in the spectral space while the scalars and density field are solved in the physical space. The presented results reveal that the autoignition spots originate and evolve at locations where (1) the composition corresponds to a small range around a specific mixture fraction, and (2) the conditional scaler dissipation rate is low. A careful examination of the data obtained indicates that the autoignition spots originate in the vortex cores, and the hot gases travel outward as combustion progresses. Hence, the applicability of the transient laminar flamelet model for this problem is questioned. The dependence of autoignition characteristics on parameters such as (1) die initial eddy-turnover time and (2) the initial ratio of length scale of scalars to that of velocities are investigated. Certain implications of new results on the conditional moment closure modeling are discussed.

Surface Structures of Silicon and Germanium

Si and Ge were cleaved on the (111) plane under ultra high vacuum and exposed to O and subsequent heat treatment. LEED and spot photometric measurements were taken. Cleaved surfaces for both Si and Ge gave the expected (2 x 1) structure. Results for O exposure were qualitatively for Si and Ge. The 1/2 orders disappeared after exposure to approx = 10 exp - exp 7. Integral orders started to weaken at 10 exp -6 to 10 exp - exp 2 torr min., disappearing at 10 exp -1 torr min. Heat treatment of Si at 900 deg C for several seconds restored the integral orders and further heating gave a new pattern with 1/3 orders. Exposure to 2 x 10 exp -6 torr min O without further heating weakened the fractional orders and at 10 exp -5 torr min they disappeared. Integral orders remained after further heating in O. For Ge integral orders were not restored after 0 exposure until heat treatment had continued at 550 deg C for several min. The (1 x 1) structure disappeared after heating at 590 deg C in 7 x 10 exp -1 torr O and further heating at 590 deg C without O restored the integral order Variations of intensity with voltage were measured for the (00) and (20) spots. The results supported a model proposed by Haneman (Phys. Rev., 1968, 170, 705) involving two kinds of atom sites on the cleaved surface. 20 ref.--E.J.S.

Nucleotide-sequence of 5S RNA from mycobacterium-smegmatis

32P labelled 5S RNA isolated fromMycobacterium smegmatis was digested withT 1 and pancreatic ribonucleases separately and fingerprinted by two dimensional high voltage electrophoresis on thin-layer DEAE-cellulose plates. The radioactive spots were sequenced and their molar yields were determined. The chain length of the 5S RNA was found to be 120. It showed resemblances to both prokaryotic and eukaryotic 5S RNAs.

Rannansiirtyminen ja ihmisen toimintaympäristön muutos Mätäjokilaakson alueella esihistoriallisella ajalla

In this thesis, I study the changing ladscape and human environment of the Mätäjoki Valley, West-Helsinki, using reconstructions and predictive modelling. The study is a part of a larger project funded by the city of Helsinki aming to map the past of the Mätäjoki Valley. The changes in landscape from an archipelago in the Ancylus Lake to a river valley are studied from 10000 to 2000 years ago. Alongside shore displacement, we look at the changing environment from human perspective and predict the location of dwelling sitesat various times. As a result, two map series were produced that show how the landscape changed and where inhabitance is predicted. To back them up, we have also looked at what previous research says about the history of the waterways, climate, vegetation and archaeology. The changing landscape of the river valley is reconstructed using GIS methods. For this purpose, new laser point data set was used and at the same time tested in the context landscape modelling. Dwelling sites were modeled with logistic regression analysis. The spatial predictive model combines data on the locations of the known dwelling sites, environmental factors and shore displacement data. The predictions were visualised into raster maps that show the predictions for inhabitance 3000 and 5000 years ago. The aim of these maps was to help archaeologists map potential spots for human activity. The produced landscape reconstructions clarified previous shore displacement studies of the Mätäjoki region and provided new information on the location of shoreline. From the shore displacement history of the Mätäjoki Valley arise the following stages: 1. The northernmost hills of the Mätäjoki Valley rose from Ancylus Lake approximately 10000 years ago. Shore displacement was fast during the following thousand years. 2. The area was an archipelago with a relatively steady shoreline 9000 7000 years ago. 8000 years ago the shoreline drew back in the middle and southern parts of the river valley because of the transgression of the Litorina Sea. 3. Mätäjoki was a sheltered bay of the Litorina Sea 6000 5000 years ago. The Vantaanjoki River started to flow into the Mätäjoki Valley approximately 5000 years ago. 4. The sediment plains in the southern part of the river valley rose from the sea rather quickly 5000 3000 years ago. Salt water still pushed its way into the southermost part of the valley 4000 years ago. 5. The shoreline proceeded to Pitäjänmäki rapids where it stayed at least a thousand years 3000 2000 years ago. The predictive models managed to predict the locations of dwelling sites moderately well. The most accurate predictions were found on the eastern shore and Malminkartano area. Of the environment variables sand and aspect of slope were found to have the best predictive power. From the results of this study we can conclude that the Mätäjoki Valley has been a favorable location to live especially 6000 5000 years ago when the climate was mild and vegetation lush. The laser point data set used here works best in shore displacement studies located in rural areas or if further specific palaeogeographic or hydrologic analysis in the research area is not needed.

Importance of local heating in the compaction of thermally sensitive solids

Local heating is an important parameter in compaction of thermally sensitive solids since local hot spots could conceivably raise the temperature of the system by several hundred degrees. To understand the importance of local hot spots, 20 g of ammonium perchlorate (AP) and potassium perchlorate (KP) were pressed together at 1500 kg cm−2 for 5 min. The surface structural examination of the compact revealed a secondary phase at the interfaces between the grains in the compositions ranging from 50% AP-50% KP to 10% AP-90% KP. The observation of the secondary phase only at the interfaces has been attributed to the short life times of temperature pulses present during the compaction. An interesting aspect of the investigation is the formation of a series of solid solutions of AP-KP.

How the development of condensation particle counters is reforming our view on atmospheric nucleation

Aerosol particles deteriorate air quality, atmospheric visibility and our health. They affect the Earth s climate by absorbing and scattering sunlight, forming clouds, and also via several feed-back mechanisms. The net effect on the radiative balance is negative, i.e. cooling, which means that particles counteract the effect of greenhouse gases. However, particles are one of the poorly known pieces in the climate puzzle. Some of the airborne particles are natural, some anthropogenic; some enter the atmosphere in particle form, while others form by gas-to-particle conversion. Unless the sources and dynamical processes shaping the particle population are quantified, they cannot be incorporated into climate models. The molecular level understanding of new particle formation is still inadequate, mainly due to the lack of suitable measurement techniques to detect the smallest particles and their precursors. This thesis has contributed to our ability to measure newly formed particles. Three new condensation particle counter applications for measuring the concentration of nano-particles were developed. The suitability of the methods for detecting both charged and electrically neutral particles and molecular clusters as small as 1 nm in diameter was thoroughly tested both in laboratory and field conditions. It was shown that condensation particle counting has reached the size scale of individual molecules, and besides measuring the concentration they can be used for getting size information. In addition to atmospheric research, the particle counters could have various applications in other fields, especially in nanotechnology. Using the new instruments, the first continuous time series of neutral sub-3 nm particle concentrations were measured at two field sites, which represent two different kinds of environments: the boreal forest and the Atlantic coastline, both of which are known to be hot-spots for new particle formation. The contribution of ions to the total concentrations in this size range was estimated, and it could be concluded that the fraction of ions was usually minor, especially in boreal forest conditions. Since the ionization rate is connected to the amount of cosmic rays entering the atmosphere, the relative contribution of neutral to charged nucleation mechanisms extends beyond academic interest, and links the research directly to current climate debate.

Bacteria colonizing paper machines

Bacteria growing in paper machines can cause several problems. Biofilms detaching from paper machine surfaces may lead to holes and spots in the end product or even break the paper web leading to expensive delays in production. Heat stable endospores will remain viable through the drying section of paper machine, increasing the microbial contamination of paper and board. Of the bacterial species regularly found in the end products, Bacillus cereus is the only one classified as a pathogen. Certain B. cereus strains produce cereulide, the toxin that causes vomiting disease in food poisonings connected to B. cereus. The first aim of this thesis was to identify harmful bacterial species colonizing paper machines and to assess the role of bacteria in the formation of end product defects. We developed quantitative PCR methods for detecting Meiothermus spp. and Pseudoxanthomonas taiwanensis. Using these methods I showed that Meiothermus spp. and Psx. taiwanensis are major biofoulers in paper machines. I was the first to be able to show the connection between end product defects and biofilms in the wet-end of paper machines. I isolated 48 strains of primary-biofilm forming bacteria from paper machines. Based on one of them, strain K4.1T, I described a novel bacterial genus Deinobacterium with Deinobacterium chartae as the type species. I measured the transfer of Bacillus cereus spores from packaging paper into food. To do this, we constructed a green fluorescent protein (GFP) labelled derivative of Bacillus thuringiensis and prepared paper containing spores of this strain. Chocolate and rice were the recipient foods when transfer of the labelled spores from the packaging paper to food was examined. I showed that only minority of the Bacillus cereus spores transferred into food from packaging paper and that this amount is very low compared to the amount of B. cereus naturally occurring in foods. Thus the microbiological risk caused by packaging papers is very low. Until now, the biological function of cereulide for the producer cell has remained unknown. I showed that B. cereus can use cereulide to take up K+ from environment where K+ is scarce: cereulide binds K+ ions outside the cell with high affinity and transports these ions across cell membrane into the cytoplasm. Externally added cereulide increased the growth rate of cereulide producing strains in medium where potassium was growth limiting. In addition, cereulide producing strains outcompeted cereulide non-producing B. cereus in potassium deficient environment, but not when the potassium concentration was high. I also showed that cereulide enhances biofilm formation of B. cereus.

Studies on the phase transitions in thiourea

Thiourea (CS(NH2)2) is one of the few examples of molecular crystals exhibiting ferroelectric properties. The dielectric constant along the ferroelectric axis [100] shows maxima at 169, 177 and 202 K. An inflection point occurs at 170.5 KZ Following Goldsmith and White the phases are named as I (F.E. below 169 K), II (A.F.E. 169 Kspots in the x-ray and neutron scattering indicates the presence of structural modulation in phases 11, 111 and IV.4,5 The effect of structural modulation is to destroy the local n glide symmetry, though the overall structure is Pnma. Thiourea also exhibits thermoluminescence after being irradiated with x-rays which is accounted for by defects like NH3+ and NH- formed by the breaking of hydrogen bonds.