Improved uniformity of target illumination by combining a lens array and the technique of spectral dispersion

A scheme using a lens array and the technique of spectral dispersion is presented to improve target illumination uniformity in laser produced plasmas. Detailed two-dimensional simulation shows that a quasi-near-field target pattern, of steeper edges and without side lobes, is achieved with a lens array, while interference stripes inside the pattern are smoothed out by the use of the spectral dispersion technique. Moving the target slightly from the exact focal plane of the principal focusing lens can eliminate middle-scale-length intensity fluctuation further. Numerical results indicate that a well-irradiated laser spot with small nonuniformity and great energy efficiency can be obtained in this scheme. (c) 2007 American Institute of Physics.

Beam smoothing by lens array with spectral dispersion

A scheme of combining technology of lens array (LA) and smoothing by spectral dispersion (SSD) is introduced to improve the irradiation uniformity in laser fusion based on the earlier works on LA. The feasibility of the scheme is also analyzed by numerical simulation. It shows that a focal pattern with flat-top and sharp-edge profile could be obtained, and the irradiation nonuniformity can fall down from 14% with only LA to 3% with both SSD and LA. And this smoothing scheme is depended less on the incidence comparing to other smoothing methods. The preliminary experiment has demonstrated its effectiveness. (c) 2006 Elsevier B.V. All rights reserved.

Two-dimensional performance of uniform irradiation with the use of an edge-softened lens array and spectral dispersion

A lens array composed of edge-softened elements is used to improve on-target irradiation uniformity in the Shenguang II Laser Facility, with which a Fresnel pattern of suppressed diffraction peaks is obtained. Additional uniformity can be reached by reducing short-wavelength interference speckles inside the pattern when the technique of smoothing by spectral dispersion is also used. Two-dimensional performance of irradiation is simulated and the results indicate that a pattern of steeper edges and a flat top can be achieved with this joint technique. (c) 2007 Optical Society of America.

Encoded cell grating array in anti-counterfeit technology

The dot matrix hologram (DMH) has been widely used in anti-counterfeiting label. With the same technology and cell array configuration, we can encode to the incidence beam. These codes can be some image matrix grating with different grating gap and different grating orientation. When the multi-level phase diffractive grating is etched, the incidence beam on the cell appears as an encoding image. When the encoded grating and DMH are used in the same label synchronously, the technology of multi-encoded grating array enhances the anti-counterfeit ability.

Line-width reduction of a laser diode array using an external cavity with two feedback mirrors

A novel Littman-Metcalf external cavity laser diode array with two feedback mirrors is introduced. The line-width broadening effect caused by smile can be reduced by the novel external cavity. At the drive current of 16A, the line-width is narrowed to 0.1nm from free-running width of 1.6nm with output efficiency of 84%.

Calculations of bond dissociation energies and dipole moments in energetic materials using density-functional methods

We compare the effectiveness of six exchange/correlation functional combinations (Becke/Lee, Yang and Parr; Becke-3/Lee, Yang and Parr; Becke/Perdew-Wang 91; Becke-3/Perdew-Wang 91; Becke/Perdew 86; Becke-3/Perdew 86) for computing C-N, O-O and N-NO2 dissociation energies and dipole moments of five compounds. The studied compounds are hexabydro-1,3,5-trinitro-1,3,5-triazine (RDX), dimethylnitramine, cyanogen, nitromethane and ozone. The Becke-3/Perdew 86 in conjunction with 6-31G

Beam quality improvement of laser diode array by using off-axis external cavity

A novel off-axis external cavity is designed for laser diode array to improve the beam quality. In this external cavity, a circle aperture with variable size is used as a spatial filter. The diameter of aperture is optimized to 1.2mm and the off-axis angle of external cavity is optimized at 2.6 deg. In the optimal case, the beam parameter product (BPP) of laser diode array is reduced to 121 mm. mrad from 1050 mm. mrad with external cavity optical efficiency of 81%. (C) 2007 Optical Society of America.

Experimental demonstration of phase locking of a two-dimensional fiber laser array using a self-imaging resonator

Phase locking of a two-dimensional fiber laser array is experimentally demonstrated by using a self-imaging resonator and a spatial filter. The stable beam profiles of in-phase mode and out-of-phase mode are observed by controlling the position of spatial filter. The phase locking fiber array with in-phase mode has produced 26 W coherent output. An antisymmetric eigenmode is also observed in our experiments. The phase locking is not sensitive to power variations among the pump beams and the configuration has the ability to repair a missing element. (C) 2008 American Institute of Physics.

Beam combination of a radial laser array: Flat-topped beam

An analytical expression of a radial laser array for flat-topped beam is derived based on the generalized Collins formula. The intensity distribution of the resulting beam focused by a lens at the focus plane, for phase-locked and nonphase-locked cases, is studied numerically. The effect of the Fresnel number and normalized radius on intensity distribution for phase-locked and nonphase-locked cases is also presented. It is found that intensity distribution for nonphase-locked case is much less sensible to the Fresnel number and normalized radius than that of phase-locked case. (C) 2008 Elsevier Ltd. All rights reserved.

Beam collimation of high-power laser diode array with graded-index fiber lens array

Graded-index (GRIN) fiber lens arrays are fabricated from commercial GRIN fibers to collimate a high-power laser diode array. The beam divergence angles are reduced to 4.2 and 14.7 mrad in the fast and slow axes, respectively. The influences of smile and fluctuation in fiber length are discussed. Using an aspherical focal lens system, about 74% power can be launched into a fiber with a numerical aperture (NA) of 0.22 and a core diameter of 400 mu m. (c) 2008 Society of Photo-Optical Instrumentation Engineers.

Self-organized microvoid array perpendicular to the femtosecond laser beam in CaF2 crystals

Microvoid arrays were self-organized when femtosecond laser beam was tightly focused at a fixed point inside CaF2 crystal sample. Except void array grown below the focal point which had been reported before, we found another void array grown vertical to the laser propagation direction. This result has potential application in the fabrication of integrated micro-optic elements and photonic crystals. The possible mechanism of the phenomenon was proposed and verified experimentally.

Diseño de antenas array para comunicación entre vehículos.

[ES]El objetivo final del trabajo fin de grado, que se expone en este documento, trata sobre el diseño de un array de antena de microstrip, con la intención de que se utilice para aplicaciones de comunicación entre vehículos que trabajen en la banda de los 5 GHz, bajo el estándar ITS-G5/IEEE 802.11p, además de su fabricación y medición posterior para poder compararlos con las simulaciones. Se buscará que la ganancia de la antena sea la máxima posible pero tratando de conseguir a su vez el mayor ancho de banda dentro del rango de frecuencias requerido. Para el diseño se partirá de un único parche y se le irán añadiendo los demás componentes progresivamente (reflectores, desfasadores, mayor número de parches, transformadores λ/4, etc.) y se irán estudiando sus simulaciones. Todas estas simulaciones se realizarán con el programa HFSS.

Electrochemical fabrication and electronic behavior of polypyrrole nano-fiber array devices

Electrochemically active Polypyrrole (PPy) nano-fiber array device was fabricated via electrochemical deposition method using aluminum anodic oxide (AAO) membrane as template. After alkaline treatment electrochemically active PPy nano-fiber lost electrochemical activity, and became electrochemically inactive PPy. The electronic properties of PPy nano-fiber array devices were measured by means of a simple method. It was found that for an indium-tin oxide/electrochemically inactive PPy nano-fiber device, the conductivity of nano-fiber increased with the increase of voltage applied on the two terminals of nano-fiber. The electrochemical inactive PPy nano-fiber might be used as a nano-fiber switching diode. Both Au/electrochemically active PPy and Au/electrochemically inactive PPy nano-fiber devices demonstrate rectifying behavior, and might have been used for further application as nano-rectifiers. (c) 2005 Elsevier B.V. All tights reserved.

Formation of array microstructures on silicon by multibeam interfered ferntosecond laser pulses

We report on an optical interference method to fabricate array microstructures on the surface of silicon wafers by means of five-beam interference of femtosecond laser pulses. Optical microscope and scanning electron microscope observations revealed microstructures with micrometer-order were fabricated. The diffraction characteristics of the fabricated structures were evaluated. The present technique allows one-step realization of functional optoelectronic devices on silicon surface. (C) 2004 Elsevier B.V. All rights reserved.