Structural, thermal and optical properties of CaBO and CaLiBO glasses doped with Eu3+

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Thermal and structural properties of tantalum alkali-phosphate glasses

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The kinetic of mullite crystallization: Effect of water content

The kinetic of mullite crystallization from sol–gel method, with different water content, was investigated under non-isothermal conditions using DTA. The sols were obtained from Al(NO3)3.9H2O (ANN) and Si(OC2H5)4 (TEOS) mixtures by varying the water–alcohol content of the system. The crystalline phase changes were verified by X-ray diffraction (XRD). For a sample prepared using ethanol-based alkoxide solution (M0), only Al-poor mullite (p-mullite) crystallizes at 1000 °C; for the one synthesized with low water concentration (M6) Al-rich mullite (r-mullite) and spinel crystallize together; and for a sample prepared using a water-based alkoxide solution only spinel is formed. Thus, the variation of water contents during the synthesis caused great variations in the course of mullitization process. The average value of the apparent activation energy determined for p-mullite, r-mullite and spinel phase crystallization were found to be E = (899 ± 61) kJ mol−1, E = (1015 ± 272) kJ mol−1 and E = (980 ± 196) kJ mol−1, respectively. These results showed that sample M(0) was a monophasic gel, where aluminum and silicon atoms are mixed at a molecular level while sample M(100) was a diphasic gel, where silicon and aluminum atoms are distributed in a nanometric level. The fast reaction between TEOS and water molecules is responsible for this great difference in the sample's homogeneity. The kinetic model of the crystallization process was determined using Malek's procedure. It was established that the crystallization of p-mullite, r-mullite and spinel phase can be described by Šesták–Berggren autocatalytic model.

Opto-electrical properties of single layer flexible electroluminescence device with ruthenium complex

In this work, a ruthenium hexafluorophosphate complex, [Ru(bpy)(3)](PF6)(2) in poly(methylmethacrylate) (PMMA) was employed to build a single layer light electrochemical cell on indium tin oxide polyester flexible substrate. The electroluminescence spectrum features a relatively broad band peaked near 625 run, with CIE (x,y) color coordinates of (0.61,0.39). The driving voltage is only 3 V, and for the maximum electrical current of 10 mA the brightness reaches 1 cd/m(2). Regarding the useful application of the device, its opto-electrical behavior under mechanical strain was studied considering the central curvature. In these situations, both electrical characterization in DC mode and luminance were analyzed. (C) 2007 Elsevier B.V. All rights reserved.

Luminescence properties of the TRIMEB inclusion compound of a europium tris-beta-diketonate

The adduct TRIMEB:Eu(BTA)(3)center dot 2H(2)O was prepared and primarily characterized by photoluminescence (PL), and compared with free Eu(BTA)(3)center dot 2H(2)O. Both spectra show the Eu3+ ion emission, with subtle differences between lines for the free and encapsulated complex. The temperature dependence and chemical stability were studied, taking into account (in the latter case) the PL changes with time. The use of this new material as the emissive layer in OLEDs was tested by its successful incorporation into a device, using a conductive polymer as host. The use of the TRIMEB adduct increased the stability of the device (as compared with the free Eu complex). (C) 2008 Elsevier B.V. All rights reserved.

Organic light emitting diodes with europium (III) emissive layers based on beta-diketonate complexes: The influence of the central ligand

This work shows a comparative study of organic light emitting diodes based on four different europium complexes with the general formula, Eu(CLs)(3)bipyridine, where the central ligands are DBM [tris(dibenzoylmethane)], TTA [tris(1-(2-thieneyl)-4,4,4-trifluoro-1,3-butanedione)], NTA [tris(1-(2-naphthoyl)-3,3,3-trifluoroacetone)] and BTA [tris(1-(2-benzoyl)-3,3,3-trifluoroacetone)]. All devices have a driving voltage of 14-16 V, a very low electrical current at normal operation (less than 1 mA) and a good Wall Plug Efficiency (up to near 10(-3)%). The most suitable central ligand was found to be DBM, with an optical power up to 200 nW (at 612 nm). The BTA exhibits the lowest stability under high applied voltages. The other central ligands have similar results among them. The electroluminescence spectra clearly show the europium ion transitions (with a strong (5)D(0) -> (7)F(2) line) with a CIE color coordinate around (0.56, 0.34). (C) 2008 Elsevier B.V. All rights reserved.

Photo and electroluminescence behavior of Tb(ACAC)(3)phen complex used as emissive layer on organic light emitting diodes

This work shows the luminescence properties of a rare-earth organic complex, the Tb(ACAC)(3)phen. The results show the (5)D(4)->(7)F(3,4,5,6) transitions with no influence of the ligand. The photoluminescence excitation spectrum is tentatively interpreted by the ligands absorption. An organic light emitting diode (CLED) was made by thermal evaporation using TPD (N,N`-bis(3-methylphenyl)N,N`-diphenylbenzidine) and Alq3 (aluminum-tris(8-hydroxyquinoline)) as hole and electron transport layers, respectively. The emission reproduces the photoluminescence spectrum of the terbium complex at room temperature, with Commission Internationale de l`Eclairage - CIE (x,y) color coordinates of (0.28,0.55). No presence of any bands from the ligands was observed. The potential use of this compound in efficient devices is discussed. (C) 2008 Elsevier B.V. All rights reserved.

Efficient plasmonic coupling between Er3+:(Ag/Au) in tellurite glasses

We report a systematic study of the localized surface plasmon resonance effects on the photoluminescence of Er3+-doped tellurite glasses containing Silver or Gold nanoparticles. The Silver and Gold nanoparticles are obtained by means of reduction of Ag ions (Ag+ -> Ag-0) or Au ions (Au3+ -> Au-0) during the melting process followed by the formation of nanoparticles by heat treatment of the glasses. Absorption and photoluminescence spectra reveal particular features of the interaction between the metallic nanoparticles and Er3+ ions. The photoluminescence enhancement observed is due to dipole coupling of Silver nanoparticles with the I-4(13/2) -> I-4(15/2) Er3+ transition and Gold nanoparticles with the H-2(11/2)-> I-4(13/2) (805 nm) and S-4(3/2) -> I-4(13/2) (840 nm) Er3+ transitions. Such process is achieved via an efficient coupling yielding an energy transfer from the nanoparticles to the Er3+ ions, which is confirmed from the theoretical spectra calculated through the decay rate. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.

Electrical conductivity of silicate glasses with tetravalent cations substituting Si

The effects of substituting Si by M4+ cations in soda-lime silica glasses were analyzed by impedance spectroscopy in the frequency range of 1 Hz-1 MHz. The glass composition was (mol%) 22Na(2)O center dot 8CaO center dot 65SiO(2)center dot 5MO(2), M = Si, Ti, Ge, Zr, Sn, and Ce. Although the Na+ concentration in the glasses is constant, the Zr-containing glass exhibits the highest dc conductivity and the lowest activation energy, while the Ce-containing glass exhibits the lowest conductivity. The activation energies obtained experimentally agree with those obtained by a theoretical equation proposed by Anderson and Stuart. The differences in electrical conductivity presented by the several M-containing glasses are attributed to the effect that the M4+ ion has on the mobility of the diffusing Na+ ion. (C) 2012 Elsevier B.V. All rights reserved.

Photoluminescence in silicon/silicon oxide films produced by the Pulsed Electron Beam Ablation technique

In this work we report studies of the photoluminescence emission in samples based on Si/SiOx films deposited by the Pulsed Electron Beam Ablation (PEBA) technique. The samples were prepared at room temperature using targets with different Si/SiO2 concentrations. The samples were characterized using X-ray Absorption Edge Spectroscopy (XANES) at the Si-K edge, Raman spectroscopy, Photoluminescence (PL) and X-ray Photoelectron Spectroscopy (XPS). The concentration of a-Si and nc-Si in the film was dependent on the silicon concentration in the target. It was also observed that the PL is strongly dependent on the structural amorphous/crystalline arrangement. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.

Determination of carrier mobility in MEH-PPV thin-films by stationary and transient current techniques

Charge transport and shelf-degradation of MEH-PPV thin-films were investigated through stationary (e.g. current versus voltage - JxV) and transient (e.g. Time-of-Flight - ToF, Dark-Injection Space-Charge-Limited Current - DI-SCLC, Charge Extraction by Linearly Increasing Voltage - CELN) current techniques. Charge carrier mobility in nanometric films was best characterized through JxV and DI-SCLC. It approaches 10(-6) cm(2)Ns under a SCLC regime with deep traps for light-emitting diode applications. ToF measurements performed on micrometric layers (i.e. - 3 mu m) confirmed studies in 100 nm-thick films as deposited in OLEDs. All results were comparable to a similar poly(para-phenylene vinylene) derivative, MDMO-PPV. Electrical properties extracted from thin-film transistors demonstrated mobility dependence on carrier concentration in the channel (similar to 10(-7)-10(-4) cm(2)/Vs). At low accumulated charge levels and reduced free carrier concentration, a perfect agreement to the previously cited techniques was observed. Degradation was verified through mobility reduction and changes in trap distribution of states. (C) 2011 Elsevier B.V. All rights reserved.

Organocatalytic asymmetric mannich-type reactions: an easy approach to optically active amine derivatives

The topics I came across during the period I spent as a Ph.D. student are mainly two. The first concerns new organocatalytic protocols for Mannich-type reactions mediated by Cinchona alkaloids derivatives (Scheme I, left); the second topic, instead, regards the study of a new approach towards the enantioselective total synthesis of Aspirochlorine, a potent gliotoxin that recent studies indicate as a highly selective and active agent against fungi (Scheme I, right). At the beginning of 2005 I had the chance to join the group of Prof. Alfredo Ricci at the Department of Organic Chemistry of the University of Bologna, starting my PhD studies. During the first period I started to study a new homogeneous organocatalytic aza-Henry reaction by means of Cinchona alkaloid derivatives as chiral base catalysts with good results. Soon after we introduced a new protocol which allowed the in situ synthesis of N-carbamoyl imines, scarcely stable, moisture sensitive compounds. For this purpose we used α-amido sulfones, bench stable white crystalline solids, as imine precursors (Scheme II). In particular we were able to obtain the aza-Henry adducts, by using chiral phase transfer catalysis, with a broad range of substituents as R-group and excellent results, unprecedented for Mannich-type transformations (Scheme II). With the optimised protocol in hand we have extended the methodology to the other Mannich-type reactions. We applied the new method to the Mannich, Strecker and Pudovik (hydrophosphonylation of imines) reactions with very good results in terms of enantioselections and yields, broadening the usefulness of this novel protocol. The Mannich reaction was certainly the most extensively studied work in this thesis (Scheme III). Initially we developed the reaction with α-amido sulfones as imine precursors and non-commercially available malonates with excellent results in terms of yields and enantioselections.3 In this particular case we recorded 1 mol% of catalyst loading, very low for organocatalytic processes. Then we thought to develop a new Mannich reaction by using simpler malonates, such as dimethyl malonate.4 With new optimised condition the reaction provided slightly lower enantioselections than the previous protocol, but the Mannich adducts were very versatile for the obtainment of β3-amino acids. Furthermore we performed the first addition of cyclic β-ketoester to α-amido sulfones obtaining the corresponding products in good yield with high level of diastereomeric and enantiomeric excess (Scheme III). Further studies were done about the Strecker reaction mediated by Cinchona alkaloid phase-transfer quaternary ammonium salt derivatives, using acetone cyanohydrin, a relatively harmless cyanide source (Scheme IV). The reaction proceeded very well providing the corresponding α-amino nitriles in good yields and enantiomeric excesses. Finally, we developed two new complementary methodologies for the hydrophosphonylation of imines (Scheme V). As a result of the low stability of the products derived from aromatic imines, we performed the reactions in mild homogeneous basic condition by using quinine as a chiral base catalyst giving the α-aryl-α-amido phosphonic acid esters as products (Scheme V, top).6 On the other hand, we performed the addition of dialkyl phosphite to aliphatic imines by using chiral Cinchona alkaloid phase transfer quaternary ammonium salt derivatives using our methodology based on α-amido sulfones (Scheme V, bottom). The results were good for both procedures covering a broad range of α-amino phosphonic acid ester. During the second year Ph.D. studies, I spent six months in the group of Prof. Steven V. Ley, at the Department of Chemistry of the University of Cambridge, in United Kingdom. During this fruitful period I have been involved in a project concerning the enantioselective synthesis of Aspirochlorine. We provided a new route for the synthesis of a key intermediate, reducing the number of steps and increasing the overall yield. Then we introduced a new enantioselective spirocyclisation for the synthesis of a chiral building block for the completion of the synthesis (Scheme VI).

Modern charge density studies: the entanglement of experiment and theory

This tutorial review article is intended to provide a general guidance to a reader interested to learn about the methodologies to obtain accurate electron density mapping in molecules and crystalline solids, from theory or from experiment, and to carry out a sensible interpretation of the results, for chemical, biochemical or materials science applications. The review mainly focuses on X-ray diffraction techniques and refinement of experimental models, in particular multipolar models. Neutron diffraction, which was widely used in the past to fix accurate positions of atoms, is now used for more specific purposes. The review illustrates three principal analyses of the experimental or theoretical electron density, based on quantum chemical, semi-empirical or empirical interpretation schemes, such as the quantum theory of atoms in molecules, the semi-classical evaluation of interaction energies and the Hirshfeld analysis. In particular, it is shown that a simple topological analysis based on a partition of the electron density cannot alone reveal the whole nature of chemical bonding. More information based on the pair density is necessary. A connection between quantum mechanics and observable quantities is given in order to provide the physical grounds to explain the observations and to justify the interpretations.

Molecular dynamics modeling and simulation of void growth in two dimensions

The mechanisms of growth of a circular void by plastic deformation were studied by means of molecular dynamics in two dimensions (2D). While previous molecular dynamics (MD) simulations in three dimensions (3D) have been limited to small voids (up to ≈10 nm in radius), this strategy allows us to study the behavior of voids of up to 100 nm in radius. MD simulations showed that plastic deformation was triggered by the nucleation of dislocations at the atomic steps of the void surface in the whole range of void sizes studied. The yield stress, defined as stress necessary to nucleate stable dislocations, decreased with temperature, but the void growth rate was not very sensitive to this parameter. Simulations under uniaxial tension, uniaxial deformation and biaxial deformation showed that the void growth rate increased very rapidly with multiaxiality but it did not depend on the initial void radius. These results were compared with previous 3D MD and 2D dislocation dynamics simulations to establish a map of mechanisms and size effects for plastic void growth in crystalline solids.