Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

A SEM, EDS and vibrational spectroscopic study of the clay mineral fraipontite

The mineral fraipontite has been studied by using a combination of scanning electron microscopy with energy dispersive analysis and vibrational spectroscopy (infrared and Raman). Fraipontite is a member of the 1:1 clay minerals of the kaolinite-serpentine group. The mineral contains Zn and Cu and is of formula (Cu,Zn,Al)3(Si,Al)2O5(OH)4. Qualitative chemical analysis of fraipontite shows an aluminium silicate mineral with amounts of Cu and Zn. This kaolinite type mineral has been characterised by Raman and infrared spectroscopy; in this way aspects about the molecular structure of fraipontite clay are elucidated.

Are there generalizable trends in the release of airborne synthetic clay nanoparticles from a jet milling process?

Despite recent efforts to assess the release of nanoparticles to the workplace during different nanotechnology activities, the existence of a generalizable trend in the particle release has yet to be identified. This study aimed to characterize the release of synthetic clay nanoparticles from a laboratory-based jet milling process by quantifying the variations arising from primary particle size and surface treatment of the material used, as well as the feed rate of the machine. A broad range of materials were used in this study, and the emitted particles mass (PM2.5) and number concentrations (PNC) were measured at the release source. Analysis of variance, followed by linear mixed-effects modeling, was applied to quantify the variations in PM2.5 and PNC of the released particles caused by the abovementioned factors. The results confirmed that using materials of different primary size and surface treatment affects the release of the particles from the same process by causing statistically-significant variations in PM2.5 and PNC. The interaction of these two factors should also be taken into account as it resulted in variations in the measured particles release properties. Furthermore, the feed rate of the milling machine was confirmed to be another influencing parameter. Although this research does not identify a specific pattern in the release of synthetic clay nanoparticles from the jet milling process generalizable to other similar settings, it emphasizes that each tested case should be handled individually in terms of exposure considerations.

Field performance of in-service cast iron water reticulation pipe buried in reactive clay

Field monitoring is an important means for understanding soil behaviour and its interaction with buried structures such as pipeline. This paper details the successful instrumentation of a section of an in-service cast iron water main buried in an area of reactive clay where frequent water pipe breakage has been observed. The instrumentation included measurement of pipe strain; pipe water pressure and temperature; soil pressure, temperature, moisture content and matric suction, as well as the meteorological conditions on site. The data generally indicated that changes in soil temperature, suction and moisture content were directly related to the local climatic variations. The suction and moisture content data indicated that the soil profile at the site down to around 700 mm, and probably down to 1000 mm, is affected by changes in surface weather, while soil conditions below this depth appear to be more stable. Analysis of pipe strain indicated that the pipe behaves like a cantilever beam, with the top experiencing predominantly tensile strains during summer. Subsequently, these trends reduce to compressive strains as soil swelling occurs due to increase of moisture content with the onset of winter.

Journal of Education and Work: Special Issue: Creative Graduate Pathways Within and Beyond the Creative Industries

This special issue explores the nuances of graduate creative work, the kinds of value that creative graduates add through work of various types, graduate employability issues for creative graduates, emerging and developing creative career identities and the implications for educators who are tasked with developing a capable creative workforce. Extant literature tends to characterise creative careers as either ‘precarious’ and insecure, or as the engine room of the creative economy. However, in actuality, the creative workforce is far more heterogeneous than either of these positions suggest, and creative careers are far more complex and diverse than previously thought. The task of creative educators is also much more challenging than previously supposed.

Jobs for creatives outside the creative industries: A study of creatives working in the Australian manufacturing industry

More creatives work outside the creative industries than inside them. Recent Australian Census data show that 52 per cent of creatives work outside of the core creative industries. These embedded creatives make up 2 per cent of manufacturing industry employees. There is little qualitative research into embedded creatives. This paper aims to address this by exploring the contribution of creative skills to manufacturing in Australia. Through four case studies of designers and marketing staff in lighting and car seat manufacturing companies, this paper demonstrates some of the work that embedded creatives undertake in the manufacturing industry and some of the ways that they contribute to innovation. The paper also considers perspectives embedded creatives bring to manufacturing and challenges involved in being a creative worker in a non-creative industry. This research is important to economic development issues, demonstrating some of the roles of key innovators in an important industry. This work also informs the education of creative industries students who will go on to contribute in a variety of industries. Furthermore, this research exemplifies one industry where employment is available to creatives outside of the creative industries.

Disruptive innovations in complex product systems industries: A case study

We propose that disruptive changes pertaining to complex product systems (CoPS) will yield a different set of characteristics than those traditionally observed for commodity products, and seek evidence for this proposition in a case study of the Flash Converting technology, a disruptive CoPS innovation in the copper production industry. Our results show that unlike disruptions in commodity product industries, the incumbent CoPS technology does not overshoot mainstream market performance demand. Also, the disruptive CoPS innovation: (i) is not nurtured in low-end niche markets; (ii) initially satisfies mainstream market performance demand, and; (iii) has higher unit price than the incumbent technology.

The dynamics of global visual effects and games development industries: lessons for Australia’s creative industries development policy

The paper critiques the focus of creative industries policy on capability development of small and medium sized firms and the provision of regional incentives. It analyses factors affecting the competitiveness and sustainability of the games development industry and visual effects suppliers to feature films. Interviews with participants in these industries highlight the need for policy instruments to take into consideration the structure and organization of global markets and the power of lead multinational corporations. We show that although forms of economic governance in these industries may allow sustainable value capture, they are interrupted by bottlenecks in which ferocious competition among suppliers is confronted by comparatively little competition among the lead firms. We argue that current approaches to creative industries policy aimed at building self-sustaining creative industries are unlikely to be sufficient because of the globalized nature of the industries. Rather, we argue that a more profitable approach is likely to require supporting diversification of the industries as ‘feeders’ into other areas of the economy.

Are we getting accurate measurements of Ksat for sodic clay soils?

In this paper we discuss the use of a series of column experiments to improve understanding of the effect irrigation water chemistry (saline solutions) has on measurements of saturated hydraulic conductivity (Ksat) of a sodic clay soil. We highlight in particular the use of extended leaching periods to determine whether the duration of leaching affects the results. In the experiments, mixed cation solutions of two different salinity levels, 50 meq/L and 100 meq/L, were applied under constant head to columns of a repacked sodic clay soil using three replicates for each treatment. The maximum Ksat measured during leaching with the 100 meq/L solution was approximately double the maximum Ksat measured during leaching with the 50 meq/L solution. Measured flow rates were found to increase rapidly after flow commenced then decrease gradually until flow rates became stable. The final, stable flow rate was roughly 80% less than the maximum flow rate measured. Reasons for these changes in saturated hydraulic conductivity are discussed. The key finding from these experiments is that long term leaching, involving significantly more pore volumes than is commonly reported in the literature, is required to obtain a ‘stable’ Ksat. We recommend that further studies be carried out to (1) determine whether similar behaviour in Ksat occurs in a wide range of sodic clay soils and (2) to help build a better understanding of the causes and implications of the observed behaviour in Ksat.

Applying HYDRUS to flow in a sodic clay soil with solution composition–dependent hydraulic conductivity

Management of sodic soils under irrigation often requires application of chemical ameliorants to improve permeability combined with leaching of excess salts. Modeling irrigation, soil treatments, and leaching in these sodic soils requires a model that can adequately represent the physical and chemical changes in the soil associated with the amelioration process. While there are a number of models that simulate reactive solute transport, UNSATCHEM and HYDRUS-1D are currently the only models that also include an ability to simulate the impacts of soil chemistry on hydraulic conductivity. Previous researchers have successfully applied these models to simulate amelioration experiments on a sodic loam soil. To further gauge their applicability, we extended the previous work by comparing HYDRUS simulations of sodic soil amelioration with the results from recently published laboratory experiments on a more reactive, repacked sodic clay soil. The general trends observed in the laboratory experiments were able to be simulated using HYDRUS. Differences between measured and simulated results were attributed to the limited flexibility of the function that represents chemistry-dependent hydraulic conductivity in HYDRUS. While improvements in the function could be made, the present work indicates that HYDRUS-UNSATCHEM captures the key changes in soil hydraulic properties that occur during sodic clay soil amelioration and thus extends the findings of previous researchers studying sodic loams.

Hydraulic conductivity increases in a sodic clay soil in response to gypsum applications impacts of bulk density and cation exchange

Amelioration of sodic soils is commonly achieved by applying gypsum, which increases soil hydraulic conductivity by altering soil chemistry. The magnitude of hydraulic conductivity increases expected in response to gypsum applications depends on soil properties including clay content, clay mineralogy, and bulk density. The soil analyzed in this study was a kaolinite rich sodic clay soil from an irrigated area of the Lower Burdekin coastal floodplain in tropical North Queensland, Australia. The impact of gypsum amelioration was investigated by continuously leaching soil columns with a saturated gypsum solution, until the hydraulic conductivity and leachate chemistry stabilized. Extended leaching enabled the full impacts of electrolyte effects and cation exchange to be determined. For the columns packed to 1.4 g/cm3, exchangeable sodium concentrations were reduced from 5.0 ± 0.5 mEq/100 g to 0.41 ± 0.06 mEq/100 g, exchangeable magnesium concentrations were reduced from 13.9 ± 0.3 mEq/100 g to 4.3 ± 2.12 mEq/100 g, and hydraulic conductivity increased to 0.15 ± 0.04 cm/d. For the columns packed to 1.3 g/cm3, exchangeable sodium concentrations were reduced from 5.0 ± 0.5 mEq/100 g to 0.51 ± 0.03 mEq/100 g, exchangeable magnesium concentrations were reduced from 13.9 ± 0.3 mEq/100 g to 0.55 ± 0.36 mEq/100 g, and hydraulic conductivity increased to 0.96 ± 0.53 cm/d. The results of this study highlight that both sodium and magnesium need to be taken into account when determining the suitability of water quality for irrigation of sodic soils and that soil bulk density plays a major role in controlling the extent of reclamation that can be achieved using gypsum applications.

Copyright and creativity: An ongoing debate in the creative industries

This paper critically analyzes the divergent perspectives on how copyright and intellectual property laws impact creativity, innovation, and the creative industries. One perspective defines the creative industries based on copyright as the means by which revenues are generated from innovation and the dissemination of new ideas. At the same time, it has been argued that copyright and intellectual property regimes fetter creativity and innovation, and that this has become even more marked in the context of digital media convergence and the networked global creative economy. These issues have resonated in debates around the creative industries, particularly since the initial DCMS mapping study in the UK in 1998 defined creative industries as combining individual creativity and exploitable forms of intellectual property. The issue of competing claims for the relationship between copyright and the creative industries has also arisen in Australia, with a report by the Australian Law Reform Commission entitled Copyright and the Digital Economy. This paper will consider the competing claims surrounding copyright and the creative industries, and the implications for policy-makers internationally.

Welcome to Media Industries

An introduction to the journal, its goals, mission, and vision.

Public Policy for the Creative Industries

The cultural and creative industries are closely intertwined with government. This chapter reviews key economic rationales for public policy interventions for the arts, cultural and creative industries. Market failure justifications depend on the status of arts and culture as non-rival public goods, as ‘merit goods’, or the need to moderate the effects of up-front investment costs or monopoly, and the inherent uncertainty of creative production. ‘Systems failure’ too is a regular rationale for policy intervention. Using the United Kingdom as an example, the chapter shows how emphasis on these rationales has shifted over the last three decades, first in the context of industrial policies for traditional aims such as exports and job growth, which have been joined in recent years by the need for investment in intangibles, knowledge exchange, and spillover effects in the wider economy.

The Trans-Pacific Partnership: Copyright Law, the Creative Industries, and Internet Freedom

The Trans-Pacific Partnership (TPP) is a highly secretive trade agreement being negotiated between the US and eleven Pacific Rim countries, including Australia. Having obtained a fast-track authority from the United States Congress, US President Barack Obama is keen to finalise the deal. However, he was unable to achieve a resolution of the deal at recent talks in Hawaii on the TPP. A number of chapters of the TPP will affect the creative artists, cultural industries and internet freedom — including the intellectual property chapter, the investment chapter, and the electronic commerce chapter. Legacy copyright industries have pushed for longer and stronger copyright protection throughout the Pacific Rim. In the wake of the Hawaii talks, Knowledge Ecology International leaked the latest version of the intellectual property chapter of the TPP. Jamie Love of Knowledge Ecology International commented upon the leaked text about copyright law: ‘In many sections of the text, the TPP would change global norms, restrict access to knowledge, create significant financial risks for persons using and sharing information, and, in some cases, impose new costs on persons producing new knowledge goods.’ The recent leaked text reveals a philosophical debate about the nature of intellectual property law. There are mixed messages in respect of the treatment of the public domain under copyright law. In one part of the agreement on internet service providers, there is text that says that the parties recognise the need for ‘promoting innovation and creativity,’ ‘facilitating the diffusion of information, knowledge, technology, culture, and the arts’, and ‘foster competition and open and efficient markets.’ A number of countries suggested ‘acknowledging the importance of the public domain.’ The United States and Japan opposed the recognition of the public domain in this text.