A new structure of In-based ohmic contacts to n-type GaAs

Electrical, structural and reaction characteristics of In-based ohmic contacts to n-GaAs were studied. Attempts were made to form a low-band-gap interfacial phase of InGaAs to reduce the barrier height at the metal/semiconductor junction, thus yielding low-resistance, highly reliable contacts. The contacts were fabricated by e-beam sputtering Ni, NiIn and Ge targets on VPE-grown n(+)-GaAs film (approximate to 1 mu m, 2 x 10(18) cm(-3)) in ultrahigh vacuum as the structure of Ni(200 Angstrom)/NiIn(100 Angstrom)/Ge(40 Angstrom)/n(+)-GaAs/SI-GaAs, followed by rapid thermal annealing at various temperatures (500-900 degrees C). In this structure, a very thin layer of Ge was employed to play the role of heavily doping donors and diffusion limiters between In and the GaAs substrate. Indium was deposited by sputtering NiIn alloy instead of pure In in order to ensure In atoms to be distributed uniformly in the substrate; nickel was chosen to consume the excess indium and form a high-temperature alloy of Ni3In. The lowest specific contact resistivity (rho(c)) of (1.5 +/- 0.5)x 10(-6) cm(2) measured by the Transmission Line Method (TLM) was obtained after annealing at 700 degrees C for 10 s. Auger sputtering depth profile and Transmission Electron Microscopy (TEM) were used to analyze the interfacial microstructure. By correlating the interfacial microstructure to the electronical properties, InxGa1-xAs phases with a large fractional area grown epitaxially on GaAs were found to be essential for reduction of the contact resistance.

X-Band GaN Power HEMTs with Power Density of 2.23W/mm Grown on Sapphire by MOCVD

The growth,fabrication,and characterization of 0.2μm gate-length AlGaN/GaN HEMTs,with a high mobility GaN thin layer as a channel,grown on (0001) sapphire substrates by MOCVD,are described.The unintentionally doped 2.5μm thick GaN epilayers grown with the same conditions as the GaN channel have a room temperature electron mobility of 741cm2/(V·s) at an electron concentration of 1.52×1016 cm-3.The resistivity of the thick GaN buffer layer is greater than 108Ω·cm at room temperature.The 50mm HEMT wafers grown on sapphire substrates show an average sheet resistance of 440.9Ω/□ with uniformity better than 96%.Devices of 0.2μm×40μm gate periphery exhibit a maximum extrinsic transconductance of 250mS/mm and a current gain cutoff frequency of77GHz.The AlGaN/GaN HEMTs with 0.8mm gate width display a total output power of 1.78W (2.23W/mm) and a linear gain of 13.3dB at 8GHz.The power devices also show a saturated current density as high as 1.07A/mm at a gate bias of 0.5V.

耗散粒子动力学处理复杂固体壁面的一种有效方法

耗散粒子动力学(dissipative particle dynamics,DPD)作为一种介观尺度拉格朗日型粒子方法,已经成功地应用于微纳米流动和生化科技的研究中. 复杂固体壁面的处理和壁面边界条件的实施一直是DPD方法发展及应用的一个障碍. 提出了处理复杂固体壁面的一种新的方法. 复杂固体区域通过冻结随机分布并且达到平衡状态的DPD粒子代表;所冻结的DPD粒子位于临近流动区域的一个截距内;在靠近固体壁面的流动区域中设置流动反弹层,当流动DPD粒子进入此流动层后反弹回流动区域. 应用这种固体壁面处理方法.

西藏产雪莲花的化学成分研究

本学位论文报道了作为传统藏药材广泛使用的西藏产雪莲花化学成分的研究。论文由五章组成，第一章是三种西藏产雪莲花的化学成分的系统分离纯化和结构鉴定；第二章为西藏产雪莲花化学成分的液-质及串联质谱联用分析；第三章提出了以HPLC和TLC为检测方法的雪莲花药材质量标准草案；第四章给出了对西藏产雪莲花挥发油化学成分的气-质联用分析结果；第五章概述了雪莲花的化学成分及药理研究进展。 第一章包括三个部分。第一部分报道了绵头雪莲花(Saussurea laniceps Hand.-Mazz.)全草乙醇提取物化学成分的分离鉴定。采用正相硅胶柱层析及凝胶柱层析等分离方法，从西藏产绵头雪莲花的乙醇提取物中共分离鉴定出15个化合物。其中11个化合物为首次从该植物中分离得到，当中2个化合物系在凤毛菊属植物中首次发现。第二部分报道了水母雪莲花(Saussurea medusa Maxim.)全草乙醇提取物的化学成分。采用正、反相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出15个化合物，其中1个为新化合物，另有4个化合物为首次从该植物中分离得到。新化合物结构通过质谱和一维及二维核磁共振等波谱解析方法及碱水解反应确定为巴豆酰基-高车前苷(M-7)。第三部分报道了三指雪莲花 (Saussurea tridactyla Sch.-Bip. ex Hook. f.)全草乙醇提取物的化学成分。采用正相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出7个化合物，其中1个化合物为首次从该植物中分离得到。 第二章也包括三个部分。首先是采用液-质联用(HPLC-DAD-ESI-MSn)分析方法，对7个西藏不同产地的三指雪莲花化学成分进行了分析，通过与标准品的 UV和MS数据比较，共鉴定出14个峰，并对其中8个共有成分进行了定量测定。其次是关于八种西藏产雪莲花化学成分的液-质联用(HPLC-DAD-ESI-MSn)分析，通过与标准品的UV和MS数据比较，共鉴定出15个峰，并对其中8个共有成分进行了定量检测。最后通过对八种西藏产雪莲花主要化学成分的多级串联质谱(ESI-MSn)分析，快速、灵敏地鉴定出10个黄酮和3个香豆素化学成分。 第三章同样包括三个部分。首先是以绵头雪莲花中主要香豆素成分东莨菪素和伞形花内酯为对照品，通过TLC定性检测和HPLC含量测定，草拟出较严谨的药材质量标准。其次是将绵头雪莲花、三指雪莲花和雪兔子作为一个药材看待，草拟了以东莨菪素和伞形花内酯的TLC检测为指标的药材质量标准。最后是针对水母雪莲花，以主要黄酮成分芹菜素-7-O-b-D-葡萄糖苷为对照品作TLC检测，并草拟出该药材的质量标准草案。 第四章报道了西藏产雪莲花挥发油的化学成分分析。采用传统水蒸气蒸馏法分别从八种雪莲花全草中提取挥发油，利用气相色谱-质谱联用技术分别从水母雪莲花、绵头雪莲花、槲叶雪莲花、云状雪兔子、拉萨雪兔子、小果雪兔子、雪兔子和三指雪莲花中分别鉴定出83、83、56、34、21、20、24和20个化学成分，分别占其挥发油总量的70.7%、76.0%、82.2%、55.4%、49.7%、70.4 %、76.2%和 76.7%。 第五章为综述，总结和概括了雪莲花的化学和药理研究进展。 The dissertation reports the investigation of the chemical constituents of the genus Saussurea. Quite a lot of species in this genus are traditional Tibetan medicinal plants, and hence have been widely used in traditional Tibetan medicine. This dissertation consisted of five chapters. The first chapter is on the chemical constituents of three Saussurea plants. The second section is about the analysis of chemical constituents of Saussurea plants using HPLC-MS and ESI-MS/MS. In the third chapter, we proposed quality-control standards for the Genus Saussurea based on TLC (thin layer chromatography) and HPLC. The fourth chapter is about chemical compositions of the essential oil from the whole plant of Saussurea plants. The last chapter reviews the research progress of the Genus Saussurea. The first chapter consists of three parts. The first part is about chemical constituents of ethanol extracts from whole plant of Saussurea laniceps Hand.-Mazz. Fifteen compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. Among them, eleven compounds were isolated from this plant for the first time, and two compounds were isolated from Genus Saussurea for the first time. The second part is about chemical constituents of ethanol extracts from whole plant of Saussurea medusa Maxim. Fifteen compounds were isolated by column chromatography on normal phase, reversed phase silica gel and Sephadex LH-20. Five of them were isolated from this plant for the first time, and there is one new flavonoid glucoside which was identified as 6″-O-crotonoyl-homoplantaginin (M-7) based on the evidence of one- and two-dimensional nuclear magnetic resonance, mass spectrometry analysis, and alkaline hydrolysis reaction. The last part is about chemical constituents of ethanol extracts from whole plant of Saussurea tridactyla Sch.-Bip. ex Hook. f.. Seven compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. There is one compound which was isolated from this plant for the first time. The second chapter consists of three parts. In the first part, we analyzed the chemical constituents of S. tridactyla collected from seven different places in Tibet using HPLC-DAD-ESI-MSn. Fourteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds, among which eight common peaks were quantified. In the second part, we analyzed the chemical constituents of eight Saussurea species using HPLC-DAD-ESI-MSn method. Fifteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds and eight main peaks of them were quantified. In the last part, we analyzed the chemical compounds of the above eight Saussurea plants directly by ESI-MS/MS. Thirteen major compounds, including 10 flavonoids and 3 coumarins were easily rapidly identified. The third chapter consists of three parts. In the first part, we proposed a comparative high quality-control standard for S. laniceps, based on quality detection by TLC and quantity analysis by HPLC using two major compounds (umbelliferone and scopoletin) as standard compounds. In the second part, in viewing S. laniceps, S. tridactyla and S. gossypiphora as the members of one family of medicinal herbs, we suggested a quality-control standard based on the TLC detection of the two major compounds (umbelliferone and scopoletin). In the last part, we proposed a quality-control standard for S. medusa based on the TLC detection of its major component (apigenin 7-O-glucoside). The four chapter analyzed the chemical constituents of essential oil of eight Saussurea species. The essential oils were extracted from the whole plants of these samples with water stream distillation. By GC-MS analysis, we identified eighty-three compounds from S. medusa, eighty-three from S. laniceps, fifty-six from S. quercifolia, thirty-four from S. aster, twenty-one from S. kingii, twenty from S. simpsoniana, twenty-four from S. gossypiphora, and twenty from S. tridactyla respetively, which accounted for 70.7%, 76.0%, 82.2%, 55.4%, 49.7%, 70.4 %, 76.2% and 76.7% of the total essential oil, respectively. The last chapter reviews the research progress of the Genus Saussurea.

鲜甘薯快速乙醇发酵条件的初步研究

本文对不同菌种（酵母菌和运动发酵单胞菌）快速生产燃料乙醇的条件进行了研究，实现了鲜甘薯快速转化为燃料乙醇。全文分为两部分： 第一部分：酵母菌快速生产燃料乙醇的条件研究。通过单因素试验，酵母菌快速生产燃料乙醇的条件为：发酵方式采用边糖化边发酵（SSF），蒸煮温度为85 ℃，料水比2:1（初始糖浓度 210 g/kg），糖化酶用量0.75 AGU/g 鲜甘薯，接种量10%（v/w）。在最优条件下，经过24 h发酵，乙醇浓度可达97.44 g/kg, 发酵效率为92%，发酵强度为4.06 g/kg/h。由于采用了低温蒸煮和SSF，可以大大节约能耗，从而降低乙醇生产的成本。同时，利用摇瓶优化的条件，进行了10 L，100 L，500 L发酵罐的放大试验，由于发酵罐初期可以人为通氧，使菌体能迅速积累，发酵时间缩短2 h，发酵效率在90%以上。 第二部分：运动发酵单胞菌快速生产燃料乙醇条件研究。通过单因素试验和正交试验获得了发酵的最佳参数：初始pH值6.0-7.0，硫酸铵5.0 g/kg，糖化酶量1.6 AUG/kg淀粉，初始糖浓度200 g/kg，接种量12.5%（v/w）。经过21 h发酵，乙醇浓度为95.15 g/kg，发酵效率可达94%。同时对不灭菌发酵也进行了研究，发酵效率可达92%。为鲜甘薯运动发酵单胞菌燃料乙醇的工业化生产打下基础。 对发酵结束后的残糖进行了研究。通过薄层层析和葡萄氧化酶测定证明：无论是酵母菌还是运动发酵单胞菌发酵结束后的发酵液中都不含葡萄糖。经过HPLC进一步分析残糖说明：发酵液中已没有葡萄糖成分；经糖化酶水解后仍没有葡萄糖出现；但经酸水解后又出现了葡萄糖，说明结束后的残糖是一些低聚糖结构。有关残糖的结构需要进一步研究。可以通过开发高效的低聚糖水解酶来降低发酵液的残糖，提高原料的利用率。 A new technology for rapid production fuel ethanol from fresh sweet potato by different microorganisms (Saccharomyces cerevisiae and Zymomonas mobilis) was gained in this research. The paper involved two parts: Part 1: The study on fuel ethanol rapid production from fresh sweet potato by Saccharomyces cerevisiae. The following parameters of Saccharomyces cerevisiae was investigated by a series of experiments: fermentation models, cooking temperature, initial sugar concentration and glucoamylase dosage. The results showed that SSF (simultaneous saccharification and fermentation) not only reduced the fermentation time (from 30 to 24h) but also enhanced the ethanol concentration (from 73.56 to 95.96 g/kg). With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg which the fermentation yield could reach to 92% and ethanol productivity 4.06 g/kg/h from sweet potato enzymatic hydrolysis. Furthermore, the savings in energy by carrying out the cooking (85 ℃) and saccharification (30 ℃) step at low temperature had been realized. The results were also verified in 10 L, 100 L and 500 L fermentor. The fermentation yield was no less than 90%. The fermentation time of fermenter was shorter than Erlenmeyer flask. This may be that the aeration in the early fermentation period is available, which lead to the rapidly commutations of biomass. Part 2: The technology of ethanol rapid production with simultaneous saccharification and fermentation ( SSF ) by Zymomonas mobilis，using fresh sweet potato as raw material was studied. The effects of various factors on the yield of ethanol were investigated by the single factor and the orthogonal experiments. As a result, the optimal technical conditions were obtained from those experiments：initial pH value 6.0-7.0, nitride 5.0 g/kg，(NH4)2SO4, glucoamylase 1.6 AUG/kg starch, inoculums concentration 12.5% (v/w). The Zymomonas mobilis was able to produce ethanol 95.15 g/kg, with 94% of the theoretical yield, from fresh sweet potato after 24 h fermentation. The fermentation efficiency of non-sterilized was also reach to 92%. We also analyzed the final fermentation residual sugars of Saccharomyces cerevisiae and Zymomonas mobilis. When the residual sugars were analyzed by thin-layer chromatogram and glucose oxidase, there was no glucose. The analysis of reducing sugars by HPLC showed that there was no glucose existed in the fermentation liquor. However, the glucose appeared after being hydrolyzed by acid. It is indicated that the residual sugars in the final fermentation liquor were the configuration of oligosaccharide, which was linked by the special glycosidic bonds. It was feasible for reducing residual sugars to develope the enzyme that can degradation the oligosaccharide.

链霉菌S227抗耐药菌活性成分的研究

本论文以从四川峨嵋山森林土壤中分离筛选获得的一株产抗耐药性活性化合物的链霉菌S227为材料，对发酵液中活性物质的分离纯化及抗耐药性活性进行了研究。 建立了抗耐药性活性的定性、定量检测方法。建立的管蝶法活性定量检测的标准回归方程为：D=4.8229Ln(C)+3.6326 R=0.9972 ；纸片法活性定量检测的标准回归方程为：D=5.5Ln(C)-12.794 R=0.999。 根据建立的样品活性的检测方法，测定了发酵液的初始活性。实验证明活性物质的温度、pH稳定性好。 通过活性的定性、定量追踪方法，分别利用等体积的石油醚、乙酸乙酯、正丁醇在不同的pH梯度下萃取，确定了pH3条件下正丁醇能最大程度的萃取活性物质，说明活性物质极性很大。对正丁醇萃取相经过两次硅胶柱层析及薄层层析分离得到具有抗耐药菌活性的纯化样品S227-4。 经过核磁共振氢谱、碳谱数据分析初步确定S227-4为四聚糖，通过糖的水解实验初步确定S227-4由葡萄糖和半乳糖组成。 纸片法活性检测表明S227-4具有抗耐药菌活性。采用MIC测定法对该样品抗耐药活性进行研究。在证明该样品本身不具有抗菌活性的基础上，以临床分离的耐药性金黄色葡萄球菌为指示菌，考察了该样品与抗生素联合使用时对耐药菌抗生素MIC（最小抑菌浓度）值的影响，结果表明在不影响菌体生长的浓度条件下，该样品能明显降低多株耐药菌对多种抗生素的MIC值，不同程度地恢复所测试耐药菌对相应抗生素的敏感性。如S227-4与青霉素钠联用可以使S. aureus 12352的MIC降低8倍，而与红霉素联用可以使S. aureus 12334的MIC降低128倍。 The purification process and the activity of the anti bacterial drug resistance compounds produced by Streptomyces S227 isolated from the forest soil sample of the Mountain E’MEI in Sichuan Province were studied in this thesis. Quantitative and qualitative activity assay methods of the active compounds were established. The regression equation of the tube method was D=4.8229Ln(C)+3.6326, R=0.9972. The regression equation of the paper method was D=5.5Ln(C)-12.794, R=0.999. According to the established activity assay method, the incipient activity of the broth was evaluated. And it was proved that the stability of the active compounds was good. By quantitative and qualitative activity tracing method, petroleum ether, ethyl acetate and butanol were used to extract the active compounds at different pH. The result showed that butanol was the most effective agent for active component recovery at pH3. From the butanol extraction a purified sample, S227-4, was isolated by silica gel column chromatography and thin-layer chromatography . S227-4 was proved to be a tetra- saccharide by 1H-NMR and 13C-NMR. And its monosaccharides include glucose and galactose by hydrolysate analysis. The anti-drug resistant activity of S227-4 was tested in vitro by MICs assay using different drug resistant Staphylococcus aureus strains isolated clinically. The sample itself showed no anti-microbial activity in growth inhibitory experiment, but when it was used together with different antibiotics, it could remarkably decrease the MICs of different clinically isolated drug-resistant bacterial strains to these antibiotics. For example, when S227-4 was used with penicillin, the MIC of S. aureus 12352 decreased 8 times compared with that when penicillin was used alone. Meanwhile when it was used with erythromycin the MIC of S. aureus 12334 deceased 128 times compared with erythromycin alone.

一株丝状真菌对半纤维素利用的初步研究

本文筛选出一株能利用木糖产乙醇的丝状真菌Z7，对其利用木糖和半纤维素水解产物产乙醇的发酵条件进行了研究，并对Z7 利用玉米芯产木聚糖酶的条件进行了优化。全文分为三部分： 第一部分：目标微生物筛选、纯化及系统发育分析。以木糖为唯一碳源，采用梯度稀释和平板化线法从高温、中温酒曲中分离到16 株能利用木糖良好生长的丝状真菌；通过发酵试验复筛，获得一株能产乙醇的丝状真菌Z7；综合形态学和ITS 序列分析，初步鉴定为Aspergillus flavus。 第二部分：Z7 的乙醇发酵条件研究。以木糖为碳源，通过单因素试验确定最佳氮源和发酵温度；通过正交试验及SPSS 软件分析得到了不同N、P、K 成分对乙醇、残糖和菌体干重的影响。获得最佳的发酵条件为：（g/L）木糖50，尿素1, NH4NO3 1, K2HPO4 2 , KCl 0.5 , MgSO4.7H2O 0.5 , NaNO3 1 , pH 自然，培养温度33 ℃。以玉米芯半纤维素稀酸水解液为底物进行乙醇发酵，根据稀酸水解的单糖释放量和乙醇产量，确定115 ℃，1 h 为最佳玉米芯预处理条件；结合最佳发酵条件，添加1 g/L 的吐温20 能获得最大的乙醇浓度8.31 g/L。因此，Aspergillus flavus Z7 能利用半纤维素水解产物产乙醇，其中木糖的利用率80%以上。 第三部分：Z7 利用玉米芯产木聚糖酶条件优化。Aspergillus flavus Z7 在具有产乙醇能力的同时还具有产木聚糖酶的能力。本文通过单因素和正交试验得到最佳产酶培养基组分为：(g/L)玉米芯20，尿素2, 酵母膏2.5, K2HPO4 5，NaNO31, MgSO4.7H2O 1。单因素试验表明，用纱布代替塑料布密封摇瓶封口能显著提高产酶量；Z7 在碱性条件下具有更强的产酶性能。在最优条件下发酵，能产生最大木聚糖酶活122.23IU/mL。通过薄层分析，验证了Z7 产生的木聚糖酶具有水解木聚糖生成木糖及木寡糖的能力。 A strain of filamentous fungus which can produce ethanol by using the xylose was isolated in this research. The ethanol fermention conditions from xylose and dilute-acid hydrolyzate of the corn core were studied. The conditions of xylanase production by Z7 were also optimized. The paper involved three parts. Part1: Isolation, purification and phylogenetic analysis of the microbe. By using xylose as the single carbon source and the pla te streaking method, several filamentous fungi were isolated from the wine starter; through the fermentation test, a filamentous fungus Z7 which can produce ethanol was further recognized; furthermore, according to the morphologic observation and ITS seque nces analysis, Z7 was identified as Aspergillus flavus at the first step. Part2: Research on the condition of ethanol fermentation by Z7. By single factor experiment, the optional nitrogen resource and temperature of the fermentation were fixed; meanwhile, through the orthogonal array tests and the analysis of statistic software SPSS, the optional component of the culture medium and the fermentation condition were organized as follows: (g/L) xylose 50, urea 1, NH4NO3 1, K2HPO4 2, KCl 0.5 , MgSO4.7H2O 0.5, NaNO31, pH nature, temperature 33℃. Based on these optimal parameters, the fermentation of dilute-acid hydrolyzate of the corn core was carried on by Z7. According to the quantities of released sugar monomers and content of the ethanol, 115℃ in 1h is the best pretreatment condition; the maximal ethanol content can be obtained when 1g/L Tween 20 was added to. Therefore, the filamentous fungus Aspergillus flavus can use the hydrolysate of hemicellulose to produce ethanol, and the rate of xylose utilization was over 80%. Part3: Optimization of Z7’s xylanase producing condition from corn core. Aspergillus flavus Z7, which can utilize xylose or the hydrolysate of hemicellulose to produce ethanol, also had the ability of xylanase production. The optional component of the culture medium were fixed by the single factor experiment and the orthogonal array tests, and they were organized as follows: (g/L) corn core 20, Urea 2, Yeast extract 2.5, K2HPO4 5, NaNO31, MgSO4.7H2O 1; it was testified by the single factor experiment that sealing the shaking flasks with pledget other than plastic paper can obviously increase the xylanase activity; moreover, Z7 showed better xylanase production ability when in the alkali environment. Under the optional fermentation condition, the maximal xylanase activity 122.23IU/mL was proved. Through the analysis of thin- layer chromatography (TLC), the ability of xylanase from Z7, which can hydrolyze xylan to xylose monomer and oligomer, was vividly displayed.

欧报春(Primula vulgaris)不同花色与色素关系及花色遗传初步分析

为了掌握欧报春各花色遗传规律服务于良种生产,通过对欧报春各色花进行色素吸收光谱和薄层层析分析,进行不同花色杂交研究,分析了欧报春各色花所含色素类型及各花色遗传规律。结果显示欧报春群体含多种花色素,单株也可含有多种花色素,形成多变的粉色、红色及蓝色花。黄色深浅主要由类胡萝卜素含量决定。白色对粉色及黄色为隐性遗传,黄色、粉色为显性遗传并有数量遗传特征,黄色与粉色独立遗传。蓝色为多基因控制的隐性遗传,并具有数量遗传特征。

Vesicles Formed by Oligostyrene-block-Oligoaniline-block-Oligostyrene Triblock Oligomer

Novel pi-conjugated coil-rod-coil triblock oligomers containing optoelectronic active oligoaniline segments were synthesized. The block oligomer can self-assemble into diverse aggregating morphologies including spherical micelles and thin-layer vesicles in THF, which is found associated with the removing of the protecting groups of oligoaniline segments. A possible mechanism was proposed to explain the self-assembly behavior changes in which chain conformation variation of the aniline segments initiated from deprotection of the nitrogen atoms is pointed to be the key factor that dominates the transition process.

Nanocomposite based on depositing platinum nanostructure onto carbon nanotubes through a one-pot, facile synthesis method for amperometric sensing

Platinum nanoparticles (Pt NPs) were deposited onto multi-walled carbon nanotubes (MWNTs) through direct chemical reduction without any other stabilizing agents. Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry were employed to characterize the morphology of the as-prepared nanocomposite (noted as Pt NPs-MWNTs) and further identify the Pt NPs on the surface of MWNTs. The nanocomposite demonstrated the ability to electrocatalyze the oxidation of hydrogen peroxide and substantially raises the response current. A sensitivity of 591.33 mu A mM(-1) cm(-2) was obtained at Pt NPs-MWNTs modified electrode. Thus, we immobilized glucose oxidase (GOD) as a model enzyme on the nanocomposite-based electrode with a thin layer of Nafion to fabricate a glucose biosensor, which showed sensitive and fast response to glucose. The influence of the GOD loading was investigated and the biosensor with an enzyme loading concentration of 10 mg/mL shows optimal performance for glucose detection, that is, a detection limit of 3 mu M and a response time of 3 s, respectively.

The study of novel Fe3O4@gamma-Fe2O3 core/shell nanomaterials with improved properties

The surface structure of the iron oxide nanoparticles obtained by the co-precipitation method has been investigated, and a thin layer of alpha-FeOOH absorbed on surface of the nanoparticle is confirmed by analyses of Fourier transform infrared (FTIR), X-ray photoelectron spectra (XPS) and surface photovoltage spectroscopy (SPS). After annealed at 400 degrees C, the alpha-FeOOH can be converted to gamma-Fe2O3. The simple-annealed procedure resulted in the formation of Fe3O4@gamma-Fe2O3 core/shell structure with improved stability and a higher magnetic saturation value, and also the simple method can be used to obtain core/shell structure in other similar system.

Investigation of heptakis(2,6-di-O-methyl)-beta-cyclodextrin inclusion complexes with flavonoid glycosides by electrospray ionization mass spectrometry

The non-covalent complexes between three flavonoid glycosides (quercitrin, hyperoside and rutin) and heptakis(2,6-di-O-methyl)-beta-cyclodextrin (DM-beta-CD) were investigated by electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICR-MS). The 1:1 complexation of each flavonoid glycoside (guest) to the DM-beta-CD (host) was monitored in the negative ion mode by mixing each guest with an up to 30-fold molar excess of the host. The binding constants for all complexes were calculated by a linear equation in the order: DM-beta-CD:quercitrin > DM-beta-CD:rutin > DM-beta-CD:hyperoside. A binding model for the complexes has also been proposed based on the binding constants and tandem mass spectrometric data of these complexes.

Rotating minidisk-disk electrodes

Rotating minidisk-disk electrode (RMDDE) was developed by replacing ring electrode of rotating ring-disk electrode (RRDE) with a minidisk electrode. Its applications were demonstrated by studying electrochemical reactions of ferricyanide and divalent copper. The replacement of ring electrode by minidisk electrode results in following advantages. First, the fabrication of RMDDE is easier than that of RRDE with the same electrode material. Second, there is more freedom in choosing electrode materials and sizes, since it is difficult to make thin ring electrodes of RRDE with fragile materials. Third, the replacement of ring electrode by minidisk electrode saves electrode materials, especially rare materials. Finally, the substitution of minidisk electrode for ring electrode allows using multiple minidisks for simultaneous monitoring of multiple components. Therefore, RMDDE is a promising generator-collector system, especially when special generator-collector systems are not commercially available, such as corrosion study and electrocatalysis study of new electrode materials.

Improved electron injection in organic light-emitting devices with a lithium acetylacetonate [Li(acac)]/aluminium bilayer cathode

Lithium acetylacetonate [Li(acac)] covered with aluminium was used as an efficient electron injection layer in organic light-emitting devices (OLEDs) consisting of NPB as the hole transport layer and Alq(3) as the electron transport and light emitting layer, resulting in lower turn- on voltage and increased current efficiency. The turn- on voltage (the voltage at a luminance of 1 cd m(-2)) was decreased from 5.5 V for the LiF/Al and 4.4 V for Ca/Al to 4.0 V for Li(acac)/Al, and the device current efficiency was enhanced from 4.71 and 5.2 to 7.0 cd A(-1). The performance tolerance to the layer thickness of Li(acac) is also better than that of the device with LiF. LiF can only be used when deposited as an ultra- thin layer because of its highly insulating nature, while the Li(acac) can be as thick as 5 nm without significantly affecting the EL performance. We suppose that the free lithium released from Li(acac) improves the electron injection when Li(acac) is covered with an Al cathode.

Organic photovoltaic cells with near infrared absorption spectrum

Organic photovoltaic cells with a strong absorption spectrum in the near infrared region were fabricated with the structure of indium tin oxide (ITO)/zinc phthalocynine (ZnPc)/lead phthalocynine (PbPc)/C-60/Al. PbPc has a broad and strong absorption, while the organic films of PbPc/C-60 showed an additional new absorption peak at 900 nm. The absorption in the near infrared region can harvest more photons to invert into photocurrent. Moreover, the introduction of ZnPc thin layer between ITO and PbPc further improved the new absorption peak and the collection of hole carriers at the electrode ITO, which increased the power conversion efficiencies to 1.95% and short-circuit current density to 9.1 mA/cm(2) under AM 1.5 solar spectrum.