Dynamic analysis using finite elements to calculate the critical wear section of the contact wire in suburban railway overhead conductor rails

The purpose of this study is to determine the critical wear levels of the contact wire of the catenary on metropolitan lines. The study has focussed on the zones of contact wire where localised wear is produced, normally associated with the appearance of electric arcs. To this end, a finite element model has been developed to study the dynamics of pantograph-catenary interaction. The model includes a zone of localised wear and a singularity in the contact wire in order to simulate the worst case scenario from the point of view of stresses. In order to consider the different stages in the wire wear process, different depths and widths of the localised wear zone were defined. The results of the dynamic simulations performed for each stage of wear let the area of the minimum resistant section of the contact wire be determined for which stresses are greater than the allowable stress. The maximum tensile stress reached in the contact wire shows a clear sensitivity to the size of the local wear zone, defined by its width and depth. In this way, if the wear measurements taken with an overhead line recording vehicle are analysed, it will be possible to calculate the potential breakage risk of the wire. A strong dependence of the tensile forces of the contact wire has also been observed. These results will allow priorities to be set for replacing the most critical sections of wire, thereby making maintenance much more efficient. The results obtained show that the wire replacement criteria currently borne in mind have turned out to be appropriate, although in some wear scenarios these criteria could be adjusted even more, and so prolong the life cycle of the contact wire.

Energy Analysis of Bare Electrodynamic Tethers

The design of an electrodynamic tether is a complex task that involves the control of dynamic instabilities, optimization of the generated power (or the descent time in deorbiting missions), and minimization of the tether mass. The electrodynamic forces on an electrodynamic tether are responsible for variations in the mechanical energy of the tethered system and can also drive the system to dynamic instability. Energy sources and sinks in this system include the following: 1) ionospheric impedance, 2) the potential drop at the cathodic contactor, 3) ohmic losses in the tether, 4) the corotational plasma electric field, and 5) generated power and/or 6) input power. The analysis of each of these energy components, or bricks, establishes parameters that are useful tools for tether design. In this study, the nondimensional parameters that govern the orbital energy variation, dynamic instability, and power generation were characterized, and their mutual interdependence was established. A space-debris mitigation mission was taken as an example of this approach for the assessment of tether performance. Numerical simulations using a dumbbell model for tether dynamics, the International Geomagnetic Reference Field for the geomagnetic field, and the International Reference Ionosphere for the ionosphere were performed to test the analytical approach. The results obtained herein stress the close relationships that exist among the velocity of descent, dynamic stability, and generated power. An optimal tether design requires a detailed tradeoff among these performances in a real-world scenario.

Sustainability of irrigated farming systems in a Tunisian region: A recursive stochastic programming analysis

The aim of this study was to evaluate the sustainability of farm irrigation systems in the Cébalat district in northern Tunisia. It addressed the challenging topic of sustainable agriculture through a bio-economic approach linking a biophysical model to an economic optimisation model. A crop growth simulation model (CropSyst) was used to build a database to determine the relationships between agricultural practices, crop yields and environmental effects (salt accumulation in soil and leaching of nitrates) in a context of high climatic variability. The database was then fed into a recursive stochastic model set for a 10-year plan that allowed analysing the effects of cropping patterns on farm income, salt accumulation and nitrate leaching. We assumed that the long-term sustainability of soil productivity might be in conflict with farm profitability in the short-term. Assuming a discount rate of 10% (for the base scenario), the model closely reproduced the current system and allowed to predict the degradation of soil quality due to long-term salt accumulation. The results showed that there was more accumulation of salt in the soil for the base scenario than for the alternative scenario (discount rate of 0%). This result was induced by applying a higher quantity of water per hectare for the alternative as compared to a base scenario. The results also showed that nitrogen leaching is very low for the two discount rates and all climate scenarios. In conclusion, the results show that the difference in farm income between the alternative and base scenarios increases over time to attain 45% after 10 years.

Implications of biofuel support policies in Europe - a quantitative analysis in an open economy

EU biofuels support Biofuels modelling with CAPRI Scenario setting Main results Concluding remarks Biofuels production and use will remain mainly driven by public support Strong links of biofuels to agricultural markets Development of second generation technologies would ease food-fuel links

Analysis of ad hoc routing protocols for emergency and rescue scenarios.

A mobile ad hoc network MANET is a collection of wireless mobile nodes that can dynamically configure a network without a fixed infrastructure or centralized administration. This makes it ideal for emergency and rescue scenarios where information sharing is essential and should occur as soon as possible. This article discusses which of the routing strategies for mobile ad hoc networks: proactive, reactive and hierarchical, have a better performance in such scenarios. Using a real urban area being set for the emergency and rescue scenario, we calculate the density of nodes and the mobility model needed for validation. The NS2 simulator has been used in our study. We also show that the hierarchical routing strategies are beffer suited for this type of scenarios.

Analysis, monitoring, and management of quality of experience in video delivery services over IP

Esta tesis estudia la monitorización y gestión de la Calidad de Experiencia (QoE) en los servicios de distribución de vídeo sobre IP. Aborda el problema de cómo prevenir, detectar, medir y reaccionar a las degradaciones de la QoE desde la perspectiva de un proveedor de servicios: la solución debe ser escalable para una red IP extensa que entregue flujos individuales a miles de usuarios simultáneamente. La solución de monitorización propuesta se ha denominado QuEM(Qualitative Experience Monitoring, o Monitorización Cualitativa de la Experiencia). Se basa en la detección de las degradaciones de la calidad de servicio de red (pérdidas de paquetes, disminuciones abruptas del ancho de banda...) e inferir de cada una una descripción cualitativa de su efecto en la Calidad de Experiencia percibida (silencios, defectos en el vídeo...). Este análisis se apoya en la información de transporte y de la capa de abstracción de red de los flujos codificados, y permite caracterizar los defectos más relevantes que se observan en este tipo de servicios: congelaciones, efecto de “cuadros”, silencios, pérdida de calidad del vídeo, retardos e interrupciones en el servicio. Los resultados se han validado mediante pruebas de calidad subjetiva. La metodología usada en esas pruebas se ha desarrollado a su vez para imitar lo más posible las condiciones de visualización de un usuario de este tipo de servicios: los defectos que se evalúan se introducen de forma aleatoria en medio de una secuencia de vídeo continua. Se han propuesto también algunas aplicaciones basadas en la solución de monitorización: un sistema de protección desigual frente a errores que ofrece más protección a las partes del vídeo más sensibles a pérdidas, una solución para minimizar el impacto de la interrupción de la descarga de segmentos de Streaming Adaptativo sobre HTTP, y un sistema de cifrado selectivo que encripta únicamente las partes del vídeo más sensibles. También se ha presentado una solución de cambio rápido de canal, así como el análisis de la aplicabilidad de los resultados anteriores a un escenario de vídeo en 3D. ABSTRACT This thesis proposes a comprehensive approach to the monitoring and management of Quality of Experience (QoE) in multimedia delivery services over IP. It addresses the problem of preventing, detecting, measuring, and reacting to QoE degradations, under the constraints of a service provider: the solution must scale for a wide IP network delivering individual media streams to thousands of users. The solution proposed for the monitoring is called QuEM (Qualitative Experience Monitoring). It is based on the detection of degradations in the network Quality of Service (packet losses, bandwidth drops...) and the mapping of each degradation event to a qualitative description of its effect in the perceived Quality of Experience (audio mutes, video artifacts...). This mapping is based on the analysis of the transport and Network Abstraction Layer information of the coded stream, and allows a good characterization of the most relevant defects that exist in this kind of services: screen freezing, macroblocking, audio mutes, video quality drops, delay issues, and service outages. The results have been validated by subjective quality assessment tests. The methodology used for those test has also been designed to mimic as much as possible the conditions of a real user of those services: the impairments to evaluate are introduced randomly in the middle of a continuous video stream. Based on the monitoring solution, several applications have been proposed as well: an unequal error protection system which provides higher protection to the parts of the stream which are more critical for the QoE, a solution which applies the same principles to minimize the impact of incomplete segment downloads in HTTP Adaptive Streaming, and a selective scrambling algorithm which ciphers only the most sensitive parts of the media stream. A fast channel change application is also presented, as well as a discussion about how to apply the previous results and concepts in a 3D video scenario.

Core physics and safety analysis of Generation-IV Sodium Fast Reactors using existing and newly developed computational tools

El futuro de la energía nuclear de fisión dependerá, entre otros factores, de la capacidad que las nuevas tecnologías demuestren para solventar los principales retos a largo plazo que se plantean. Los principales retos se pueden resumir en los siguientes aspectos: la capacidad de proporcionar una solución final, segura y fiable a los residuos radiactivos; así como dar solución a la limitación de recursos naturales necesarios para alimentar los reactores nucleares; y por último, una mejora robusta en la seguridad de las centrales que en definitiva evite cualquier daño potencial tanto en la población como en el medio ambiente como consecuencia de cualquier escenario imaginable o más allá de lo imaginable. Siguiendo estas motivaciones, la Generación IV de reactores nucleares surge con el compromiso de proporcionar electricidad de forma sostenible, segura, económica y evitando la proliferación de material fisible. Entre los sistemas conceptuales que se consideran para la Gen IV, los reactores rápidos destacan por su capacidad potencial de transmutar actínidos a la vez que permiten una utilización óptima de los recursos naturales. Entre los refrigerantes que se plantean, el sodio parece una de las soluciones más prometedoras. Como consecuencia, esta tesis surgió dentro del marco del proyecto europeo CP-ESFR con el principal objetivo de evaluar la física de núcleo y seguridad de los reactores rápidos refrigerados por sodio, al tiempo que se desarrollaron herramientas apropiadas para dichos análisis. Efectivamente, en una primera parte de la tesis, se abarca el estudio de la física del núcleo de un reactor rápido representativo, incluyendo el análisis detallado de la capacidad de transmutar actínidos minoritarios. Como resultado de dichos análisis, se publicó un artículo en la revista Annals of Nuclear Energy [96]. Por otra parte, a través de un análisis de un hipotético escenario nuclear español, se evalúo la disponibilidad de recursos naturales necesarios en el caso particular de España para alimentar una flota específica de reactores rápidos, siguiendo varios escenarios de demanda, y teniendo en cuenta la capacidad de reproducción de plutonio que tienen estos sistemas. Como resultado de este trabajo también surgió una publicación en otra revista científica de prestigio internacional como es Energy Conversion and Management [97]. Con objeto de realizar esos y otros análisis, se desarrollaron diversos modelos del núcleo del ESFR siguiendo varias configuraciones, y para diferentes códigos. Por otro lado, con objeto de poder realizar análisis de seguridad de reactores rápidos, son necesarias herramientas multidimensionales de alta fidelidad específicas para reactores rápidos. Dichas herramientas deben integrar fenómenos relacionados con la neutrónica y con la termo-hidráulica, entre otros, mediante una aproximación multi-física. Siguiendo este objetivo, se evalúo el código de difusión neutrónica ANDES para su aplicación a reactores rápidos. ANDES es un código de resolución nodal que se encuentra implementado dentro del sistema COBAYA3 y está basado en el método ACMFD. Por lo tanto, el método ACMFD fue sometido a una revisión en profundidad para evaluar su aptitud para la aplicación a reactores rápidos. Durante ese proceso, se identificaron determinadas limitaciones que se discutirán a lo largo de este trabajo, junto con los desarrollos que se han elaborado e implementado para la resolución de dichas dificultades. Por otra parte, se desarrolló satisfactoriamente el acomplamiento del código neutrónico ANDES con un código termo-hidráulico de subcanales llamado SUBCHANFLOW, desarrollado recientemente en el KIT. Como conclusión de esta parte, todos los desarrollos implementados son evaluados y verificados. En paralelo con esos desarrollos, se calcularon para el núcleo del ESFR las secciones eficaces en multigrupos homogeneizadas a nivel nodal, así como otros parámetros neutrónicos, mediante los códigos ERANOS, primero, y SERPENT, después. Dichos parámetros se utilizaron más adelante para realizar cálculos estacionarios con ANDES. Además, como consecuencia de la contribución de la UPM al paquete de seguridad del proyecto CP-ESFR, se calcularon mediante el código SERPENT los parámetros de cinética puntual que se necesitan introducir en los típicos códigos termo-hidráulicos de planta, para estudios de seguridad. En concreto, dichos parámetros sirvieron para el análisis del impacto que tienen los actínidos minoritarios en el comportamiento de transitorios. Concluyendo, la tesis presenta una aproximación sistemática y multidisciplinar aplicada al análisis de seguridad y comportamiento neutrónico de los reactores rápidos de sodio de la Gen-IV, usando herramientas de cálculo existentes y recién desarrolladas ad' hoc para tal aplicación. Se ha empleado una cantidad importante de tiempo en identificar limitaciones de los métodos nodales analíticos en su aplicación en multigrupos a reactores rápidos, y se proponen interesantes soluciones para abordarlas. ABSTRACT The future of nuclear reactors will depend, among other aspects, on the capability to solve the long-term challenges linked to this technology. These are the capability to provide a definite, safe and reliable solution to the nuclear wastes; the limitation of natural resources, needed to fuel the reactors; and last but not least, the improved safety, which would avoid any potential damage on the public and or environment as a consequence of any imaginable and beyond imaginable circumstance. Following these motivations, the IV Generation of nuclear reactors arises, with the aim to provide sustainable, safe, economic and proliferationresistant electricity. Among the systems considered for the Gen IV, fast reactors have a representative role thanks to their potential capacity to transmute actinides together with the optimal usage of natural resources, being the sodium fast reactors the most promising concept. As a consequence, this thesis was born in the framework of the CP-ESFR project with the generic aim of evaluating the core physics and safety of sodium fast reactors, as well as the development of the approppriated tools to perform such analyses. Indeed, in a first part of this thesis work, the main core physics of the representative sodium fast reactor are assessed, including a detailed analysis of the capability to transmute minor actinides. A part of the results obtained have been published in Annals of Nuclear Energy [96]. Moreover, by means of the analysis of a hypothetical Spanish nuclear scenario, the availability of natural resources required to deploy an specific fleet of fast reactor is assessed, taking into account the breeding properties of such systems. This work also led to a publication in Energy Conversion and Management [97]. In order to perform those and other analyses, several models of the ESFR core were created for different codes. On the other hand, in order to perform safety studies of sodium fast reactors, high fidelity multidimensional analysis tools for sodium fast reactors are required. Such tools should integrate neutronic and thermal-hydraulic phenomena in a multi-physics approach. Following this motivation, the neutron diffusion code ANDES is assessed for sodium fast reactor applications. ANDES is the nodal solver implemented inside the multigroup pin-by-pin diffusion COBAYA3 code, and is based on the analytical method ACMFD. Thus, the ACMFD was verified for SFR applications and while doing so, some limitations were encountered, which are discussed through this work. In order to solve those, some new developments are proposed and implemented in ANDES. Moreover, the code was satisfactorily coupled with the thermal-hydraulic code SUBCHANFLOW, recently developed at KIT. Finally, the different implementations are verified. In addition to those developments, the node homogenized multigroup cross sections and other neutron parameters were obtained for the ESFR core using ERANOS and SERPENT codes, and employed afterwards by ANDES to perform steady state calculations. Moreover, as a result of the UPM contribution to the safety package of the CP-ESFR project, the point kinetic parameters required by the typical plant thermal-hydraulic codes were computed for the ESFR core using SERPENT, which final aim was the assessment of the impact of minor actinides in transient behaviour. All in all, the thesis provides a systematic and multi-purpose approach applied to the assessment of safety and performance parameters of Generation-IV SFR, using existing and newly developed analytical tools. An important amount of time was employed in identifying the limitations that the analytical nodal diffusion methods present when applied to fast reactors following a multigroup approach, and interesting solutions are proposed in order to overcome them.

A 2D computational parametric analysis of the sheltering effect of fences on a railway vehicle standing on a bridge and experiencing crosswinds

In a crosswind scenario, the risk of high-speed trains overturning increases when they run on viaducts since the aerodynamic loads are higher than on the ground. In order to increase safety, vehicles are sheltered by fences that are installed on the viaduct to reduce the loads experienced by the train. Windbreaks can be designed to have different heights, and with or without eaves on the top. In this paper, a parametric study with a total of 12 fence designs was carried out using a two-dimensional model of a train standing on a viaduct. To asses the relative effectiveness of sheltering devices, tests were done in a wind tunnel with a scaled model at a Reynolds number of 1 × 105, and the train’s aerodynamic coefficients were measured. Experimental results were compared with those predicted by Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations of flow, showing that a computational model is able to satisfactorily predict the trend of the aerodynamic coefficients. In a second set of tests, the Reynolds number was increased to 12 × 106 (at a free flow air velocity of 30 m/s) in order to simulate strong wind conditions. The aerodynamic coefficients showed a similar trend for both Reynolds numbers; however, their numerical value changed enough to indicate that simulations at the lower Reynolds number do not provide all required information. Furthermore, the variation of coefficients in the simulations allowed an explanation of how fences modified the flow around the vehicle to be proposed. This made it clear why increasing fence height reduced all the coefficients but adding an eave had an effect mainly on the lift force coefficient. Finally, by analysing the time signals it was possible to clarify the influence of the Reynolds number on the peak-to-peak amplitude, the time period and the Strouhal number.

Comparative study of two laparoscopic instrument tracker designs for motion analysis and image-guided surgery: a technical evaluation

Laparoscopic instrument tracking systems are a key element in image-guided interventions, which requires high accuracy to be used in a real surgical scenario. In addition, these systems are a suitable option for objective assessment of laparoscopic technical skills based on instrument motion analysis. This study presents a new approach that improves the accuracy of a previously presented system, which applies an optical pose tracking system to laparoscopic practice. A design enhancement of the artificial markers placed on the laparoscopic instrument as well as an improvement of the calibration process are presented as a means to achieve more accurate results. A technical evaluation has been performed in order to compare the accuracy between the previous design and the new approach. Results show a remarkable improvement in the fluctuation error throughout the measurement platform. Moreover, the accumulated distance error and the inclination error have been improved. The tilt range covered by the system is the same for both approaches, from 90º to 7.5º. The relative position error is better for the new approach mainly at close distances to the camera system

Vulnerability analysis of RC buildings with wide beams located in moderate seismicity regions

A significant number of short-to-mid height RC buildings with wide beams have been constructed in areas of moderate seismicity of Spain, mainly for housing and administrative use. The buildings have a framed structure with one-way slabs; the wide beams constitute the distinctive characteristic, their depth being equal to that of the rest of the slab, thus providing a flat lower surface, convenient for construction and the layout of facilities. Seismic behavior in the direction of the wide beams appears to be deficient because of: (i) low lateral strength, mainly because of the small effective depth of the beams, (ii) inherent low ductility of the wide beams, generated by high amount of reinforcement, (iii) the big strut compressive forces developed inside the column-beam connections due to the low height of the beams, and (iv) the fact that the wide beams are wider than the columns, meaning that the contribution of the outer zones to the resistance of the beam-column joints is unreliable because there is no torsion reinforcement. In the orthogonal direction, the behavior is worse since the only members of the slabs that contribute to the lateral resistance are the joists and the façade beams. Moreover, these buildings were designed with codes that did not include ductility requirements and required only a low lateral resistance; indeed, in many cases, seismic action was not considered at all. Consequently, the seismic capacity of these structures is not reliable. The objective of this research is to assess numerically this capability, whereas further research will aim to propose retrofit strategies. The research approach consists of: (i) selecting a number of 3-story and 6-story buildings that represent the vast majority of the existing ones and (ii) evaluating their vulnerability through three types of analyses, namely: code-type, push-over and nonlinear dynamic analysis. Given the low lateral resistance of the main frames, the cooperation of the masonry infill walls is accounted for; for each representative building, three wall densities are considered. The results of the analyses show that the buildings in question exhibit inadequate seismic behavior in most of the examined situations. In general, the relative performance is less deficient for Target Drift CP (Collapse Prevention) than for IO (Immediate Occupancy). Since these buildings are selected to be representative of the vast majority of buildings with wide beams that were constructed in Spain without accounting for any seismic consideration, our conclusions can be extrapolated to a broader scenario.

Assessing urban mobility through participatory scenario building and combined utility-regret assessment

La planificación de la movilidad sostenible urbana es una tarea compleja que implica un alto grado de incertidumbre debido al horizonte de planificación a largo plazo, la amplia gama de paquetes de políticas posibles, la necesidad de una aplicación efectiva y eficiente, la gran escala geográfica, la necesidad de considerar objetivos económicos, sociales y ambientales, y la respuesta del viajero a los diferentes cursos de acción y su aceptabilidad política (Shiftan et al., 2003). Además, con las tendencias inevitables en motorización y urbanización, la demanda de terrenos y recursos de movilidad en las ciudades está aumentando dramáticamente. Como consecuencia de ello, los problemas de congestión de tráfico, deterioro ambiental, contaminación del aire, consumo de energía, desigualdades en la comunidad, etc. se hacen más y más críticos para la sociedad. Esta situación no es estable a largo plazo. Para enfrentarse a estos desafíos y conseguir un desarrollo sostenible, es necesario considerar una estrategia de planificación urbana a largo plazo, que aborde las necesarias implicaciones potencialmente importantes. Esta tesis contribuye a las herramientas de evaluación a largo plazo de la movilidad urbana estableciendo una metodología innovadora para el análisis y optimización de dos tipos de medidas de gestión de la demanda del transporte (TDM). La metodología nueva realizado se basa en la flexibilización de la toma de decisiones basadas en utilidad, integrando diversos mecanismos de decisión contrariedad‐anticipada y combinados utilidad‐contrariedad en un marco integral de planificación del transporte. La metodología propuesta incluye dos aspectos principales: 1) La construcción de escenarios con una o varias medidas TDM usando el método de encuesta que incorpora la teoría “regret”. La construcción de escenarios para este trabajo se hace para considerar específicamente la implementación de cada medida TDM en el marco temporal y marco espacial. Al final, se construyen 13 escenarios TDM en términos del más deseable, el más posible y el de menor grado de “regret” como resultado de una encuesta en dos rondas a expertos en el tema. 2) A continuación se procede al desarrollo de un marco de evaluación estratégica, basado en un Análisis Multicriterio de Toma de Decisiones (Multicriteria Decision Analysis, MCDA) y en un modelo “regret”. Este marco de evaluación se utiliza para comparar la contribución de los distintos escenarios TDM a la movilidad sostenible y para determinar el mejor escenario utilizando no sólo el valor objetivo de utilidad objetivo obtenido en el análisis orientado a utilidad MCDA, sino también el valor de “regret” que se calcula por medio del modelo “regret” MCDA. La función objetivo del MCDA se integra en un modelo de interacción de uso del suelo y transporte que se usa para optimizar y evaluar los impactos a largo plazo de los escenarios TDM previamente construidos. Un modelo de “regret”, llamado “referencedependent regret model (RDRM)” (modelo de contrariedad dependiente de referencias), se ha adaptado para analizar la contribución de cada escenario TDM desde un punto de vista subjetivo. La validación de la metodología se realiza mediante su aplicación a un caso de estudio en la provincia de Madrid. La metodología propuesta define pues un procedimiento técnico detallado para la evaluación de los impactos estratégicos de la aplicación de medidas de gestión de la demanda en el transporte, que se considera que constituye una herramienta de planificación útil, transparente y flexible, tanto para los planificadores como para los responsables de la gestión del transporte. Planning sustainable urban mobility is a complex task involving a high degree of uncertainty due to the long‐term planning horizon, the wide spectrum of potential policy packages, the need for effective and efficient implementation, the large geographical scale, the necessity to consider economic, social, and environmental goals, and the traveller’s response to the various action courses and their political acceptability (Shiftan et al., 2003). Moreover, with the inevitable trends on motorisation and urbanisation, the demand for land and mobility in cities is growing dramatically. Consequently, the problems of traffic congestion, environmental deterioration, air pollution, energy consumption, and community inequity etc., are becoming more and more critical for the society (EU, 2011). Certainly, this course is not sustainable in the long term. To address this challenge and achieve sustainable development, a long‐term perspective strategic urban plan, with its potentially important implications, should be established. This thesis contributes on assessing long‐term urban mobility by establishing an innovative methodology for optimizing and evaluating two types of transport demand management measures (TDM). The new methodology aims at relaxing the utility‐based decision‐making assumption by embedding anticipated‐regret and combined utilityregret decision mechanisms in an integrated transport planning framework. The proposed methodology includes two major aspects: 1) Construction of policy scenarios within a single measure or combined TDM policy‐packages using the survey method incorporating the regret theory. The purpose of building the TDM scenarios in this work is to address the specific implementation in terms of time frame and geographic scale for each TDM measure. Finally, 13 TDM scenarios are built in terms of the most desirable, the most expected and the least regret choice by means of the two‐round Delphi based survey. 2) Development of the combined utility‐regret analysis framework based on multicriteria decision analysis (MCDA). This assessment framework is used to compare the contribution of the TDM scenario towards sustainable mobility and to determine the best scenario considering not only the objective utility value obtained from the utilitybased MCDA, but also a regret value that is calculated via a regret‐based MCDA. The objective function of the utility‐based MCDA is integrated in a land use and transport interaction model and is used for optimizing and assessing the long term impacts of the constructed TDM scenarios. A regret based model, called referente dependent regret model (RDRM) is adapted to analyse the contribution of each TDM scenario in terms of a subjective point of view. The suggested methodology is implemented and validated in the case of Madrid. It defines a comprehensive technical procedure for assessing strategic effects of transport demand management measures, which can be useful, transparent and flexible planning tool both for planners and decision‐makers.

Cover crops effect on farm benefits and nitrate leaching: Linking economic and environmental analysis.

Introducing cover crops (CC) interspersed with intensively fertilized crops in rotation has the potential to reduce nitrate leaching. This paper evaluates various strategies involving CC between maize and compares the economic and environmental results with respect to a typical maize?fallow rotation. The comparison is performed through stochastic (Monte-Carlo) simulation models of farms? profits using probability distribution functions (pdfs) of yield and N fertilizer saving fitted with data collected from various field trials and pdfs of crop prices and the cost of fertilizer fitted from statistical sources. Stochastic dominance relationships are obtained to rank the most profitable strategies from a farm financial perspective. A two-criterion comparison scheme is proposed to rank alternative strategies based on farm profit and nitrate leaching levels, taking the baseline scenario as the maize?fallow rotation. The results show that when CC biomass is sold as forage instead of keeping it in the soil, greater profit and less leaching of nitrates are achieved than in the baseline scenario. While the fertilizer saving will be lower if CC is sold than if it is kept in the soil, the revenue obtained from the sale of the CC compensates for the reduced fertilizer savings. The results show that CC would perhaps provide a double dividend of greater profit and reduced nitrate leaching in intensive irrigated cropping systems in Mediterranean regions.

A framework for the analysis and optimization of delay in multiview video coding schemes

Esta tesis presenta un novedoso marco de referencia para el análisis y optimización del retardo de codificación y descodificación para vídeo multivista. El objetivo de este marco de referencia es proporcionar una metodología sistemática para el análisis del retardo en codificadores y descodificadores multivista y herramientas útiles en el diseño de codificadores/descodificadores para aplicaciones con requisitos de bajo retardo. El marco de referencia propuesto caracteriza primero los elementos que tienen influencia en el comportamiento del retardo: i) la estructura de predicción multivista, ii) el modelo hardware del codificador/descodificador y iii) los tiempos de proceso de cuadro. En segundo lugar, proporciona algoritmos para el cálculo del retardo de codificación/ descodificación de cualquier estructura arbitraria de predicción multivista. El núcleo de este marco de referencia consiste en una metodología para el análisis del retardo de codificación/descodificación multivista que es independiente de la arquitectura hardware del codificador/descodificador, completada con un conjunto de modelos que particularizan este análisis del retardo con las características de la arquitectura hardware del codificador/descodificador. Entre estos modelos, aquellos basados en teoría de grafos adquieren especial relevancia debido a su capacidad de desacoplar la influencia de los diferentes elementos en el comportamiento del retardo en el codificador/ descodificador, mediante una abstracción de su capacidad de proceso. Para revelar las posibles aplicaciones de este marco de referencia, esta tesis presenta algunos ejemplos de su utilización en problemas de diseño que afectan a codificadores y descodificadores multivista. Este escenario de aplicación cubre los siguientes casos: estrategias para el diseño de estructuras de predicción que tengan en consideración requisitos de retardo además del comportamiento tasa-distorsión; diseño del número de procesadores y análisis de los requisitos de velocidad de proceso en codificadores/ descodificadores multivista dado un retardo objetivo; y el análisis comparativo del comportamiento del retardo en codificadores multivista con diferentes capacidades de proceso e implementaciones hardware. ABSTRACT This thesis presents a novel framework for the analysis and optimization of the encoding and decoding delay for multiview video. The objective of this framework is to provide a systematic methodology for the analysis of the delay in multiview encoders and decoders and useful tools in the design of multiview encoders/decoders for applications with low delay requirements. The proposed framework characterizes firstly the elements that have an influence in the delay performance: i) the multiview prediction structure ii) the hardware model of the encoder/decoder and iii) frame processing times. Secondly, it provides algorithms for the computation of the encoding/decoding delay of any arbitrary multiview prediction structure. The core of this framework consists in a methodology for the analysis of the multiview encoding/decoding delay that is independent of the hardware architecture of the encoder/decoder, which is completed with a set of models that particularize this delay analysis with the characteristics of the hardware architecture of the encoder/decoder. Among these models, the ones based in graph theory acquire special relevance due to their capacity to detach the influence of the different elements in the delay performance of the encoder/decoder, by means of an abstraction of its processing capacity. To reveal possible applications of this framework, this thesis presents some examples of its utilization in design problems that affect multiview encoders and decoders. This application scenario covers the following cases: strategies for the design of prediction structures that take into consideration delay requirements in addition to the rate-distortion performance; design of number of processors and analysis of processor speed requirements in multiview encoders/decoders given a target delay; and comparative analysis of the encoding delay performance of multiview encoders with different processing capabilities and hardware implementations.

Evaluation, energy optimization, and spectrum analysis of an artificial noise technique to improve CWSN security

This paper presents the security evaluation, energy consumption optimization, and spectrum scarcity analysis of artificial noise techniques to increase physical-layer security in Cognitive Wireless Sensor Networks (CWSNs). These techniques introduce noise into the spectrum in order to hide real information. Nevertheless, they directly affect two important parameters in Cognitive Wireless Sensor Networks (CWSNs), energy consumption and spectrum utilization. Both are affected because the number of packets transmitted by the network and the active period of the nodes increase. Security evaluation demonstrates that these techniques are effective against eavesdropper attacks, but also optimization allows for the implementation of these approaches in low-resource networks such as Cognitive Wireless Sensor Networks. In this work, the scenario is formally modeled and the optimization according to the simulation results and the impact analysis over the frequency spectrum are presented.

Controlled time of arrival feasibility analysis

Previous research studies and operational trials have shown that using the airborne Required Time of Arrival (RTA) function, an aircraft can individually achieve an assigned time to a metering or merge point accurately. This study goes a step further and investigates the application of RTA to a real sequence of arriving aircraft into Melbourne Australia. Assuming that the actual arrival times were Controlled Time of Arrivals (CTAs) assigned to each aircraft, the study examines if the airborne RTA solution would work. Three scenarios were compared: a baseline scenario being the actual flown trajectories in a two hour time-span into Melbourne, a scenario in which the sequential landing slot times of the baseline scenario were assigned as CTAs and a third scenario in which the landing slots could be freely redistributed to the inbound traffic as CTAs. The research found that pressure on the terminal area would sometimes require aircraft to lose more time than possible through the RTA capability. Using linear holding as an additional measure to absorb extensive delays, up to 500NM (5%) of total track reduction and 1300kg (3%) of total fuel consumption could be saved in the scenario with landing slots freely distributed as CTAs, compared to the baseline scenario. Assigning CTAs in an arrival sequence requires the ground system to have an accurate trajectory predictor to propose additional delay measures (path stretching, linear holding) if necessary. Reducing the achievable time window of the aircraft to add control margin to the RTA function, had a negative impact and increased the amount of intervention other than speed control required to solve the sequence. It was concluded that the RTA capability is not a complete solution but merely a tool to assist in managing the increasing complexity of air traffic.