The comparative in situ hygrothermal performance of Hemp and Stone Wool insulations in vapour open timber frame wall panels

An in situ experiment in a full scale timber frame test building was carried out to compare the hygrothermal performance of Hemp and Stone Wool insulations of identical thermal conductivity. Hemp and Stone Wool insulations were installed in timber frame wall panels without vapour barrier. The comparison was made in terms of heat transfer properties, likelihood of mould growth and condensation. Step changes in internal relative humidity were performed to explore the effect of high and normal internal moisture load on the wall panels. No significant difference between the average equivalent thermal transmittance (U-values) of the panels incorporating Hemp and Stone Wool insulations was observed. The average equivalent U-values of the panels were closer to the calculated U-values of the panels based on the manufacturers’ declared thermal conductivity of Hemp and Stone Wool insulations. It was observed that the placement of heat flux sensor along the depth of the insulation had significant influence on the measured equivalent U-value of the panels during high internal moisture load. The frequency and likelihood of condensation was higher in the interface of Stone Wool and Oriented Strand Board (OSB). In terms of the parametric assessment of mould germination potential, relative humidity, temperature and exposure conditions in the insulation-OSB interfaces were found to be favourable to germination of mould spore. However, when the insulations were dismantled, no mould was visually detected.

Reinventing America on the battlefields of Spain or following the party line: conflicting perceptions of the Spanish Civil War in the present and in the past

Isolationism and neutrality are two of the recurrent themes in the study of the history of the U.S. foreign policy in the interwar years. The trauma of the Great War, which had swept away 130.000 U.S. lives and had cost $30 billion, had led public opinion to strongly oppose any involvement with European affairs. Besides, the urgent need for economic recovery during the dismal years of the Great Depression did not leave Roosevelt much room for manoeuvre to influence international events. His positions regarding the intentions of the Fascist states remained, at best, ambivalent. These facts notwithstanding, about 2800 U.S. citizens crossed the Atlantic and rushed in to help democratic Spain, which was on the verge of becoming one more hostage in the hands of the Fascism. They joined the other British, Irish and Canadian volunteers and formed the XV International Brigade. 900 Americans never returned home. This alone should challenge the commonly held assumption that the American people were indifferent to the rise of the Fascist threat in Europe. But it also begs other questions. Considering the prevailing isolationist mood, what really motivated them? With what discursive elements did these men construct their anti Fascist representations? How far did their understanding of the Spanish democracy correspond to their own American democratic ideal? In what way did their war experience across the Atlantic mould their perception of U.S. politics (both domestic and foreign)? How far did the Spanish Civil War constitute one first step towards the realization that the U.S. might actually be drawn into another international conflict of unpredictable consequences? Last but not the least, what ideological, political and cultural complicity existed between the men from the English-speaking battalions? In order to unearth some of the answers, I intend to examine their letters and see how these men recorded the historical events in which they took part. Their correspondence emerged from the desire to prove their commitment to a common cause and spoke of a common war experience, but each letter, in its uniqueness, ends up mirroring not only the social and political background of each individual fighter, but also his own particular perspective of the war, of world politics and of the Spanish people. We shall see how these letters differ and converge and how these particular accounts weave, as in an epistolary novel, a larger-than-life narrative of outrage and solidarity, despair and hope.

Marriage and gender inequality: work–family arrangements of Portuguese and British highly qualified women

This article examines work–family reconciliation processes in order to understand if, over the course of marital life, women become socially closer or further away from their partner. Drawing on work–life interviews with highly qualified women in Portugal and Britain, we compare these processes in two societies with different historical and social backgrounds. Findings reveal three main configurations of social (in)equality which emerge during married life: growing inequality in favour of the man, in favour of the woman or equality between spouses. With due attention to the importance of national specific factors, we present three main conclusions. First, (in) equality is built up over the course of marital life and female strategies for reconciling family and work are at the core of this process. Second, the national specificities can mould the effects of cross-national gender mechanisms. Third, the intersection between cross-cultural phenomena such as conservative attitudes towards domestic work and national specificities (such as the availability of part-time options) is a rather complex process which needs further research.

Estudo da compactabilidade em laboratório de misturas betuminosas com resíduos plásticos

Dissertação para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização em Vias de Comunicação e Transportes

Micro-abrasion wear behaviour of TiAlCrSiN nanostructured coatings

The injection process of glass fibres reinforced plastics promotes the moulds surface degradation by erosion. In order to improve its wear resistance, several kinds of PVD thin hard coatings were used. It is well-known that nanostructures present a better compromise between hardness and toughness. Indeed, when the coating is constituted by a large number of ultra-thin different layers, cracks and interface troubles tend to decrease. However, it is not clear that these nanostructures present a better wear behaviour in erosion processes. In order to study its wear behaviour, a sputtered PVD nanostructured TiAlCrSiN coating was used. The substrate and film surfaces topography were analyzed by profilometry and atomic force microscopy techniques. Film adhesion to the substrate was evaluated by scratch tests. The surface hardness was measured with a Vickers micro-hardness tester. The wear resistance was evaluated by micro-abrasion with a rotating ball tribometer tests. Slurry of SiC particles in distilled water was used in order to provoke the surface abrasion. Different duration tests were performed in order to analyze the wear evolution. After these tests, the wear mechanisms developed were analyzed by scanning electron microscopy. Wear craters were measured and the wear rate was calculated and discussed. With the same purpose, coated inserts were mounted in an injection mould working with a 30% glass fibres reinforced polypropylene. After 45 000 cycles no relevant wear was registered.

Projecto de molde para peça para a indústria automóvel

A realização deste trabalho teve por base uma solicitação por parte de uma empresa dedicada ao projecto e fabrico de moldes, assim como à injecção de plásticos, no sentido de projectar um molde para a injecção de uma peça em plástico (PP-Polipropileno +20% ) para a indústria automóvel, segundo os requisitos de qualidade exigidos pelo cliente Assim, atendendo a esses requisitos, foi planeado e elaborado o projecto do respectivo molde para a injecção, tendo em consideração todos os factores que contribuem de forma activa para a obtenção das peças desejadas, com a qualidade exigida e com o tempo de vida desejado para o molde. Tendo início na definição das cavidades e movimentos do molde, passando pela selecção dos materiais mais adequados a cada um dos componentes do molde, selecção de componentes normalizados para o molde, simulação do enchimento e necessidades de arrefecimento, até à execução do molde e análise de possíveis não conformidades nas peças nele injectadas, o trabalho acompanhou todo o processo de criação do molde, desde a recepção das especificações emanadas pelo cliente, até ao teste e realização das correcções finais. Constatou-se que o molde, após ligeiras afinações finais, cumpriu com os objectivos inicialmente traçados, permitindo a obtenção de peças com o formato e qualidade exigidas pelo cliente final.

Projecto de equipamento de rotação de moldes de grande porte com recurso ao método de elementos finitos

A fabricação de moldes é uma actividade que se desenvolve em Portugal há várias décadas, com qualidade reconhecida mundialmente. A indústria automóvel é um dos principais destinos de grande parte dos moldes produzidos em Portugal. Algumas das peças produzidas nesses moldes possuem dimensões apreciáveis, tendo em conta o peso e dimensão média das peças injectadas em plástico. São exemplo disso os pára-choques dos automóveis e o tabliê. A produção dos moldes para estas peças é complexa, implicando um longo tempo de maquinagem e a manipulação dos moldes em diferentes fases, com vista ao acesso a todas as faces do molde. A IGM – Indústria Global de Moldes, SA. é a empresa responsável pela produção dos moldes para peças de média dimensão dentro do Grupo SIMOLDES. Atendendo à necessidade permanente de rodar a 90o moldes de grande porte, que podem apresentar pesos na ordem das 10 a 30 toneladas, e não existindo no mercado qualquer solução adaptável a esta necessidade, a empresa entendeu por bem levar a efeito o projecto desse equipamento, atendendo ao compromisso custo-benefício que torne viável a realização prática do mesmo. Após os esboços iniciais e uma discussão interactiva e iterativa com a empresa, foram analisadas as diferentes soluções entendidas como viáveis, tendo sido escolhido um dos anteprojectos realizados. Foram ainda discutidas as diversas alternativas de accionamento. Com base nesse anteprojecto, a estrutura foi optimizada e verificada através do Método de Elementos Finitos, tendo sido elaborado o projecto final, com o grau de detalhe necessário à sua fabricação e implementação na empresa.

Otimização do processo de injeção de ZAMAK

A indústria automóvel necessita aumentar a produtividade de forma sistemática, com vista à redução de custos e incremento da competitividade. A otimização dos produtos e processos é uma constante. O presente trabalho foi solicitado pela empresa FicoCables, do Grupo FICOSA, tendo em vista a otimização do processo de injeção de pequenas peças injetadas em ZAMAK, que constituem o bloqueio na extremidade de cada cabo metálico inserido nos automóveis para abertura da mala, portas, travão de mão, reservatório de combustível, capô, etc. A empresa possui cerca de 52 equipamentos de injeção de ZAMAK, cuja temperatura dos bicos era mantida com base numa chama de gás. Os sucessivos problemas de controlo do sistema ditaram uma mudança estratégica no aquecimento desses bicos, passando a ser usadas resistências elétricas anelares. No entanto, esta mudança veio a apresentar problemas inesperados, os quais se vieram inclusivamente a tornar em problemas de segurança, devido ao desgaste interior prematuro dos bicos, os quais apresentaram esmo problema de rotura. Paralelamente, todos os parâmetros relacionados com este processo de fabrico estavam também estudados de forma algo incipiente, pelo que se tornou necessário compreender e dissecar todas as variáveis relacionadas com o processo e implementar sistemas que impedissem o ajuste não controlado dos parâmetros por parte dos operadores. Também os moldes foram alvo de ações de melhoria, com vista a evitar problemas na zona de contacto do bico com o molde. O processo foi analisado em pormenor, permitindo um controlo muito mais apurado do mesmo. Os resultados fizeram sentir-se de forma imediata, graças ao trabalho desenvolvido neste estudo e à abertura demonstrada pela empresa para implementar todas as soluções propostas. O resultado final traduz-se num incremento significativo da segurança para os operadores, num controlo muito mais apurado de todos os parâmetros envolvidos no processo, numa maior garantia da qualidade nos produtos injetados em ZAMAK e em ganhos financeiros significativos para a empresa.

Characterization of the chitinolytic system during the mycoparasitic interaction between Trichoderma aggressivum f. aggressivum and different host strains of Agaricus bisporus /

Green mould is a serious disease of commercially grown mushrooms, the causal agent being attributed to the filamentous soil fungus Triclzodenna aggressivum f. aggressivu11l and T. aggressivum f. ellropaellm. Found worldwide, and capable of devastating crops, this disease has caused millions of dollars in lost revenue within the mushroom industry. One mechanism used by TricllOdenlla spp. in the antagonism of other fungi, is the secretion of lytic enzymes such as chitinases, which actively degrade a host's cell wall. Therefore, the intent of this study was to examine the production of chitinase enzymes during the host-parasite interaction of Agaricus bisporus (commercial mushroom) and Triclzodemza aggressivum, focusing specifically on chitinase involvement in the differential resistance of white, off-white, and brown commercial mushroom strains. Chitinases isolated from cultures of A. bisporus and T. aggressivu11l grown together and separately, were identified following native PAGE, and analysis of fluorescence based on specific enzymatic cleavage of 4-methylumbelliferyl glucoside substrates. Results indicate that the interaction between T. aggressivulll and A. bisporus involves a complex enzyme battle. It was determined that T. aggressivum produces a number of chitinases that appear to correlate to those isolated in previous studies using biocontrol strains of T. Izarziallilm. A 122 kDa N-acetylglucosaminidase of T. aggressivu11l revealed the highest and most variable activity, and is therefore believed to be an important predictor of antifungal activity. Furthermore, results indicate that brown strain resistance of mushrooms may be related to high levels of a 96 kDa N-acetylglucosaminidase, which showed elevated activity in both solitary and dual cultures with T. aggressivum. Overall, each host-parasite combination produced unique enzyme profiles, with the majority of the differences seen between day 0 and day 6 for the extracellular chitinases. Therefore, it was concluded that the antagonistic behaviour of T. aggressivli1ll does not involve a typical response, always producing the same types and levels of enzymes, but that mycoparasitism, specifically in the form of chitinase production, may be induced and regulated based on the host presented.

Cell wall degrading enzymes and interaction between Trichoderma Aggressivum and Agaricus Bisporus

Agaricus bisporus is the most commonly cultivated mushroom in North America and has a great economic value. Green mould is a serious disease of A. bisporus and causes major reductions in mushroom crop production. The causative agent of green mould disease in North America was identified as Trichoderma aggressivum f. aggressivum. Variations in the disease resistance have been shown in the different commercial mushroom strains. The purpose of this study is to continue investigations of the interactions between T. aggressivum and A. bisporus during the development of green mould disease. The main focus of the research was to study the roles of cell wall degrading enzymes in green mould disease resistance and pathogenesis. First, we tried to isolate and sequence the N-acetylglucosaminidase from A. bisporus to understand the defensive mechanism of mushroom against the disease. However, the lack of genomic and proteomic information of A. bisporus limited our efforts. Next, T. aggressivum cell wall degrading enzymes that are thought to attack Agaricus and mediate the disease development were examined. The three cell wall degrading enzymes genes, encoding endochitinase (ech42), glucanase (fJ-1,3 glucanase) and protease (prb 1), were isolated and sequenced from T. aggressivum f. aggressivum. The sequence data showed significant homology with the corresponding genes from other fungi including Trichoderma species. The transcription levels of the three T. aggressivum cell wall degrading enzymes were studied during the in vitro co-cultivation with A. bisporus using R T -qPCR. The transcription levels of the three genes were significantly upregulated compared to the solitary culture levels but were upregulated to a lesser extent in co-cultivation with a resistant strain of A. bisporus than with a sensitive strain. An Agrobacterium tumefaciens transformation system was developed for T. aggressivum and was used to transform three silencing plasmids to construct three new T. aggressivum phenotypes, each with a silenced cell wall degrading enzyme. The silencing efficiency was determined by RT-qPCR during the individual in vitro cocultivation of each of the new phenotypes with A. bisporus. The results showed that the expression of the three enzymes was significantly decreased during the in vitro cocultivation when compared with the wild type. The phenotypes were co-cultivated with A. bisporus on compost with monitoring the green mould disease progression. The data indicated that prbi and ech42 genes is more important in disease progression than the p- 1,3 glucanase gene. Finally, the present study emphasises the role of the three cell wall degrading enzymes in green mould disease infection and may provide a promising tool for disease management.

Notebook entitled Wages

Notebook entitled Wages (soft cover) – The book has mould spots on the pages. This does not affect the text. Names of wage earners include: Julia Park, Nancy McCoy, Nellie McCormick and Alice. Wages were paid by H.K. Woodruff, 1880.

Fibre optic sensor for the detection of adulterant traces in coconut oil

The design and development of a fibre optic evanescent wave refractometer for the detection of trace amounts of paraffin oil and palm oil in coconut oil is presented. This sensor is based on a side-polished plastic optical fibre. At the sensing region, the cladding and a small portion of the core are removed and the fibre nicely polished. The sensing region is fabricated in such a manner that it sits perfectly within a bent mould. This bending of the sensing region enhances its sensitivity. The oil mixture of different mix ratios is introduced into the sensing region and we observed a sharp decrease in the output intensity. The observed variation in the intensity is found to be linear and the detection limit is 2% (by volume) paraffin oil/palm oil in coconut oil. The resolution of this refractometric sensor is of the order of 10−3. Since coconut oil is consumed in large volumes as edible oil in south India, this fibre optic sensor finds great relevance for the detection of adulterants such as paraffin oil or palm oil which are readily miscible in coconut oil. The advantage of this type of sensor is that it is inexpensive and easy to set up. Another attraction of the side-polished fibre is that only a very small amount of analyte is needed and its response time is only 7 s.

Effects of grassland conversion and tillage intensities on soil microbial biomass, residues and community structure

Agricultural intensification has a strong impact on level of soil organic matter (SOM), microbial biomass stocks and microbial community structure in agro-ecosystems. The size of the microbial necromass C pool could be about 40 times that of the living microbial biomass C pool in soils. Due to the specificity, amino sugar analysis gives more important information on the relative contribution of fungal and bacterial residues to C sequestration potential of soils. Meanwhile, the relationship between microbial biomass and microbial necromass in soil and its ecological significance on SOM are not fully understood and likely to be very complex in grassland soils. This thesis focuses on the effects of tillage, grassland conversion intensities and fertilisation on microbial biomass, residues and community structure. The combined analyses of microbial biomass and residue formation of both fungi and bacteria provided a unique opportunity to study the effect of tillage, grassland conversion and fertilisation on soil microbial dynamics. In top soil at 0-30 cm layer, a reduction in tillage intensity by the GRT and NT treatments increased the accumulation of saprotrophic fungi in comparison with the MBT treatment. In contrast, the GRT and NT treatments promoted AMF at the expense of saprotrophic fungi in the bottom soil layer at 30-40 cm depth. The negative relationship between the ergosterol to microbial biomass C ratio and the fungal C to bacterial C ratio points to the importance of the relationship between saprotrophic fungi and biotrophic AMF for tillage-induced changes in microbial turnover of SOC. One-season cultivation of winter wheat with two tillage events led to a significant loss in SOC and microbial biomass C stocks at 0-40 cm depth in comparison with the permanent grassland, even 5 years after the tillage event. However, the tillage induced loss in microbial biomass C was roughly 40% less in the long-term than in the short-term of the current experiment, indicating a recovery process during grassland restoration. In general, mould board tillage and grassland conversion to maize monoculture promoted saprotrophic fungi at the expense of biotrophic AMF and bacteria compared to undisturbed grassland soils. Slurry application promoted bacterial residues as indicated by the decreases in both, the ergosterol to microbial biomass C ratio and the fungal C to bacterial C ratio. In addition, the lost microbial functional diversity due to tillage and maize monoculture was restored by slurry application both in arable and grassland soils. I conclude that the microbial biomass C/S ratio can be used as an additional indicator for a shift in microbial community. The strong relationships between microbial biomass and necromass indices points to the importance of saprotrophic fungi and biotrophic AMF for agricultural management induced effects on microbial turnover and ecosystem C storage. Quantitative information on exact biomass estimates of these two important fungal groups in soil is inevitably necessary to understand their different roles in SOM dynamics.

Two-dimensional Photonic Crystals Fabricated by Nanoimprint Lithography

We report on the process parameters of nanoimprint lithography (NIL) for the fabrication of two-dimensional (2-D) photonic crystals. The nickel mould with 2-D photonic crystal patterns covering the area up to 20mm² is produced by electron-beam lithography (EBL) and electroplating. Periodic pillars as high as 200nm to 250nm are produced on the mould with the diameters ranging from 180nm to 400nm. The mould is employed for nanoimprinting on the poly-methyl-methacrylate (PMMA) layer spin-coated on the silicon substrate. Periodic air holes are formed in PMMA above its glass-transition temperature and the patterns on the mould are well transferred. This nanometer-size structure provided by NIL is subjective to further pattern transfer.