How lowering speed limits in an urban highway affects traffics performance and emissions: the case of Madrid M-30 ring-road

The city of Madrid keeps not meeting the GHG and air pollutant limits set by the European legislation. A broad range of strategies have being taken into account to reduce both types of emissions; however traffic management meas ures are usually consigned to the sidelines. In 2004, Madrid City Council launched a plan to re-design its inner ring-road supported by a socioeconomic study that evaluated the environmental and operational benefits of the project. For safety reasons the planned speed limit for the tunnel section was finally reduced from 90km/h to 70km/h. Using a Macroscopic Traffic Model and the European Air Pollutant and Emissions Inventory Guidebook (EMEP/EEA), this paper examines the environmental and traffic performance consequences of this decision. Results support the thesis that reduced speed limits leads to GHG and air pollution reductions in the area affected by the measure without substantially altering traffic performance. The implementation of the new speed limit policy brings about a 15% and 16% reduction in both CO2 and NOx emissions respectively. Emissions’ reduction during off-peak hours is larger than during peak hours.

Reduced carbon and energy footprint in highway operations: the Highway Energy Assessment (HERA) methodology

Global demand for mobility is increasing and the environmental impact of transport has become an important issue in transportation network planning and decision-making, as well as in the operational management phase. Suitable methods are required to assess emissions and fuel consumption reduction strategies that seek to improve energy efficiency and furthering decarbonization. This study describes the development and application of an improved modeling framework – the HERA (Highway EneRgy Assessment) methodology – that enables to assess the energy and carbon footprint of different highways and traffic flow scenarios and their comparison. HERA incorporates an average speed consumption model adjusted with a correction factor which takes into account the road gradient. It provides a more comprehensive method for estimating the footprint of particular highway segments under specific traffic conditions. It includes the application of the methodology to the Spanish highway network to validate it. Finally, a case study shows the benefits from using this methodology and how to integrate the objective of carbon footprint reductions into highway design, operation and scenario comparison.

Measurement of velocity in rotational flows using ultrasonic anemometry: the flowmeter

In this paper a previously developed theoretical model of the measurement process performed by a transit-time ultrasonic anemometer is applied to a fluid flowing through a circular section pipe. This model considers the influence of the shift of the acoustic pulse trajectory from straight propagation due to the flow on the measured speed. The aim of this work is to estimate the errors induced in the measured velocity by the shift of the acoustic pulse trajectory. Using different duct’s flow models, laminar and turbulent regimes have been analyzed. The results show that neglecting the effect of shift of the acoustic pulse trajectory leads to flow rate measurement underestimation.

Desarrollo de métodos numérico-interpretativos para la realización de ensayos de bombeo

Los ensayos de bombeo son, sin lugar a dudas, una de las pruebas más fiables y de mayor interés que se hacen en el medio físico. No son pruebas estrictamente puntuales, dado que el bombeo atrae flujo desde distancias lejanas al pozo, la prueba tiene una excelente representatividad espacial. Los métodos de interpretación mediante ensayos de bombeo se empezaron a plantear en la primera mitad del pasado siglo. Con los ensayos de bombeo se puede calcular la transmisividad y coeficiente de almacenamiento de las formaciones acuíferas y suministran información sobre el tipo de acuífero, la calidad constructiva del pozo de extracción, la existencia de barreras impermeable o bordes de recarga próximos, e incluso en algunas circunstancias permiten el cálculo del área de embalse subterráneo. Desde mediados del siglo 20 existe una eficaz y abundante gama de métodos analítico-interpretativos de ensayos de bombeo, tanto en régimen permanente como transitorio. Estos métodos son ampliamente conocidos y están muy experimentados a lo largo de muchos países, sin embargo, hoy día, podrían utilizarse modelos de flujo para la interpretación, logrando la misma fiabilidad e incluso mejores posibilidades de análisis. Muchos ensayos que no pueden interpretarse porque las configuraciones del medio son demasiado complejas y no están disponibles, o no es posible, el desarrollo de métodos analíticos, tienen buena adaptación y en ocasiones muy fácil solución haciendo uso de los métodos numéricos de simulación del flujo. En esta tesis se ha buscado una vía de interpretar ensayos de bombeo haciendo uso de modelos de simulación del flujo. Se utiliza el modelo universal MODFLOW del United States Geological Survey, en el cual se configura una celda de simulación y mallado particularmente adecuados para el problema a tratar, se valida con los métodos analíticos existentes. Con la célula convenientemente validada se simulan otros casos en los que no existen métodos analíticos desarrollados dada la complejidad del medio físico a tratar y se sacan las oportunas conclusiones. Por último se desarrolla un modelo específico y la correspondiente aplicación de uso general para la interpretación numérica de ensayos de bombeo tanto con las configuraciones normales como con configuraciones complejas del medio físico. ABSTRACT Pumping tests are, without doubt, one of the most reliable and most interesting tests done in the physical environment. They are not strictly anecdotal evidence, since pumping flow attracts from far distances to the well, the test has excellent spatial representation. Methods of interpretation by pumping tests began to arise in the first half of last century. With pumping tests, can be calculated transmissivity and storage coefficient of the aquifer formations, and provide information on the type of aquifer, the construction quality of the well, the existence of waterproof barriers or borders next recharge, and even in some circumstances allow calculating the area of underground reservoir. Since the mid-20th century there is effective and abundant range of analytical interpretative pumping tests, both in steady state and transient methods. These methods are very widely known and experienced over many countries, however, nowadays, may flow models used for interpretation, obtaining equally reliable or even better possibilities for analysis. Many trials cannot be interpreted as environmental settings are too complex and are not available, or not possible, the development of analytical methods, have good adaptation and sometimes very easily solved using numerical flow simulation methods. This thesis has sought a way to interpret pumping tests using flow simulation models. MODFLOW universal model of United States Geological Survey, in which a simulation cell and meshing particularly suitable for the problem to be treated, is validated with existing analytical methods used is set. With suitably validated cell other cases where there are no analytical methods developed given the complexity of the physical environment to try and draw appropriate conclusions are simulated. Finally, a specific model and the corresponding application commonly used for numerical interpretation of pumping tests both with normal settings as complex configurations of the physical environment is developed.

Análisis de las herramientas ORCC y Vivado HLS para la Síntesis de Modelos de Flujo de Datos RVC-CAL

En este Proyecto Fin de Grado se ha realizado un estudio de cómo generar, a partir de modelos de flujo de datos en RVC-CAL (Reconfigurable Video Coding – CAL Actor Language), modelos VHDL (Versatile Hardware Description Language) mediante Vivado HLS (Vivado High Level Synthesis), incluida en las herramientas disponibles en Vivado de Xilinx. Una vez conseguido el modelo VHDL resultante, la intención es que mediante las herramientas de Xilinx se programe en una FPGA (Field Programmable Gate Array) o el dispositivo Zynq también desarrollado por Xilinx. RVC-CAL es un lenguaje de flujo de datos que describe la funcionalidad de bloques funcionales, denominados actores. Las funcionalidades que desarrolla un actor se definen como acciones, las cuales pueden ser diferentes en un mismo actor. Los actores pueden comunicarse entre sí y formar una red de actores o network. Con Vivado HLS podemos obtener un diseño VHDL a partir de un modelo en lenguaje C. Por lo que la generación de modelos en VHDL a partir de otros en RVC-CAL, requiere una fase previa en la que los modelos en RVC-CAL serán compilados para conseguir su equivalente en lenguaje C. El compilador ORCC (Open RVC-CAL Compiler) es la herramienta que nos permite lograr diseños en lenguaje C partiendo de modelos en RVC-CAL. ORCC no crea directamente el código ejecutable, sino que genera un código fuente disponible para ser compilado por otra herramienta, en el caso de este proyecto, el compilador GCC (Gnu C Compiler) de Linux. En resumen en este proyecto nos encontramos con tres puntos de estudio bien diferenciados, los cuales son: 1. Partimos de modelos de flujo de datos en RVC-CAL, los cuales son compilados por ORCC para alcanzar su traducción en lenguaje C. 2. Una vez conseguidos los diseños equivalentes en lenguaje C, son sintetizados en Vivado HLS para conseguir los modelos en VHDL. 3. Los modelos VHDL resultantes serian manipulados por las herramientas de Xilinx para producir el bitstream que sea programado en una FPGA o en el dispositivo Zynq. En el estudio del segundo punto, nos encontramos con una serie de elementos conflictivos que afectan a la síntesis en Vivado HLS de los diseños en lenguaje C generados por ORCC. Estos elementos están relacionados con la manera que se encuentra estructurada la especificación en C generada por ORCC y que Vivado HLS no puede soportar en determinados momentos de la síntesis. De esta manera se ha propuesto una transformación “manual” de los diseños generados por ORCC que afecto lo menos posible a los modelos originales para poder realizar la síntesis con Vivado HLS y crear el fichero VHDL correcto. De esta forma este documento se estructura siguiendo el modelo de un trabajo de investigación. En primer lugar, se exponen las motivaciones y objetivos que apoyan y se esperan lograr en este trabajo. Seguidamente, se pone de manifiesto un análisis del estado del arte de los elementos necesarios para el desarrollo del mismo, proporcionando los conceptos básicos para la correcta comprensión y estudio del documento. Se realiza una descripción de los lenguajes RVC-CAL y VHDL, además de una introducción de las herramientas ORCC y Vivado, analizando las bondades y características principales de ambas. Una vez conocido el comportamiento de ambas herramientas, se describen las soluciones desarrolladas en nuestro estudio de la síntesis de modelos en RVC-CAL, poniéndose de manifiesto los puntos conflictivos anteriormente señalados que Vivado HLS no puede soportar en la síntesis de los diseños en lenguaje C generados por el compilador ORCC. A continuación se presentan las soluciones propuestas a estos errores acontecidos durante la síntesis, con las cuales se pretende alcanzar una especificación en C más óptima para una correcta síntesis en Vivado HLS y alcanzar de esta forma los modelos VHDL adecuados. Por último, como resultado final de este trabajo se extraen un conjunto de conclusiones sobre todos los análisis y desarrollos acontecidos en el mismo. Al mismo tiempo se proponen una serie de líneas futuras de trabajo con las que se podría continuar el estudio y completar la investigación desarrollada en este documento. ABSTRACT. In this Project it has made a study of how to generate, from data flow models in RVC-CAL (Reconfigurable Video Coding - Actor CAL Language), VHDL models (Versatile Hardware Description Language) by Vivado HLS (Vivado High Level Synthesis), included in the tools available in Vivado of Xilinx. Once achieved the resulting VHDL model, the intention is that by the Xilinx tools programmed in FPGA or Zynq device also developed by Xilinx. RVC-CAL is a dataflow language that describes the functionality of functional blocks, called actors. The functionalities developed by an actor are defined as actions, which may be different in the same actor. Actors can communicate with each other and form a network of actors. With Vivado HLS we can get a VHDL design from a model in C. So the generation of models in VHDL from others in RVC-CAL requires a preliminary phase in which the models RVC-CAL will be compiled to get its equivalent in C. The compiler ORCC (Open RVC-CAL Compiler) is the tool that allows us to achieve designs in C language models based on RVC-CAL. ORCC not directly create the executable code but generates an available source code to be compiled by another tool, in the case of this project, the GCC compiler (GNU C Compiler) of Linux. In short, in this project we find three well-defined points of study, which are: 1. We start from data flow models in RVC-CAL, which are compiled by ORCC to achieve its translation in C. 2. Once you realize the equivalent designs in C, they are synthesized in Vivado HLS for VHDL models. 3. The resulting models VHDL would be manipulated by Xilinx tools to produce the bitstream that is programmed into an FPGA or Zynq device. In the study of the second point, we find a number of conflicting elements that affect the synthesis Vivado HLS designs in C generated by ORCC. These elements are related to the way it is structured specification in C generated ORCC and Vivado HLS cannot hold at certain times of the synthesis. Thus it has proposed a "manual" transformation of designs generated by ORCC that affected as little as possible to the original in order to perform the synthesis Vivado HLS and create the correct file VHDL models. Thus this document is structured along the lines of a research. First, the motivations and objectives that support and hope to reach in this work are presented. Then it shows an analysis the state of the art of the elements necessary for its development, providing the basics for a correct understanding and study of the document. A description of the RVC-CAL and VHDL languages is made, in addition an introduction of the ORCC and Vivado tools, analyzing the advantages and main features of both. Once you know the behavior of both tools, the solutions developed in our study of the synthesis of RVC-CAL models, introducing the conflicting points mentioned above are described that Vivado HLS cannot stand in the synthesis of design in C language generated by ORCC compiler. Below the proposed solutions to these errors occurred during synthesis, with which it is intended to achieve optimum C specification for proper synthesis Vivado HLS and thus create the appropriate VHDL models are presented. Finally, as the end result of this work a set of conclusions on all analyzes and developments occurred in the same are removed. At the same time a series of future lines of work which could continue to study and complete the research developed in this document are proposed.

Equilibration rates in lipid monolayers

A theoretical analysis is given for the rate of change of domain sizes in lipid monolayers at the air–water interface. The calculation is applicable to liquid domains formed from binary mixtures of lipids that form two coexisting liquid phases. Under conditions where the two lipid molecules have approximately equal areas, the equilibration rate does not involve macroscopic hydrodynamic flow in the subphase but rather depends on the diffusion coefficient of the lipid molecules. The calculation shows that the equilibration rate in binary mixtures of cholesterol and phosphatidylcholine is remarkably slow, the radius of a typical 20-μm diameter domain changing by as little as a part in a million per second. Under these circumstances, equilibration times of the order of days or weeks are expected. Even with such long times, the final state reached by the monolayer will in general be a state of metastable equilibrium, rather than true equilibrium.

Modelagem e simulação de redes em chip sem fio.

O paradigma das redes em chip (NoCs) surgiu a fim de permitir alto grau de integração entre vários núcleos de sistemas em chip (SoCs), cuja comunicação é tradicionalmente baseada em barramentos. As NoCs são definidas como uma estrutura de switches e canais ponto a ponto que interconectam núcleos de propriedades intelectuais (IPs) de um SoC, provendo uma plataforma de comunicação entre os mesmos. As redes em chip sem fio (WiNoCs) são uma abordagem evolucionária do conceito de rede em chip (NoC), a qual possibilita a adoção dos mecanismos de roteamento das NoCs com o uso de tecnologias sem fio, propondo a otimização dos fluxos de tráfego, a redução de conectores e a atuação em conjunto com as NoCs tradicionais, reduzindo a carga nos barramentos. O uso do roteamento dinâmico dentro das redes em chip sem fio permite o desligamento seletivo de partes do hardware, o que reduz a energia consumida. Contudo, a escolha de onde empregar um link sem fio em uma NoC é uma tarefa complexa, dado que os nós são pontes de tráfego os quais não podem ser desligados sem potencialmente quebrar uma rota preestabelecida. Além de fornecer uma visão sobre as arquiteturas de NoCs e do estado da arte do paradigma emergente de WiNoC, este trabalho também propõe um método de avaliação baseado no já consolidado simulador ns-2, cujo objetivo é testar cenários híbridos de NoC e WiNoC. A partir desta abordagem é possível avaliar diferentes parâmetros das WiNoCs associados a aspectos de roteamento, aplicação e número de nós envolvidos em redes hierárquicas. Por meio da análise de tais simulações também é possível investigar qual estratégia de roteamento é mais recomendada para um determinado cenário de utilização, o que é relevante ao se escolher a disposição espacial dos nós em uma NoC. Os experimentos realizados são o estudo da dinâmica de funcionamento dos protocolos ad hoc de roteamento sem fio em uma topologia hierárquica de WiNoC, seguido da análise de tamanho da rede e dos padrões de tráfego na WiNoC.

Evaluation of the Intelligent Cruise Control System. Volume I: study results.

National Highway Traffic Safety Administration, Washington, D.C.

The economics of reducing the county road system: three case studies in Iowa. Final report.

Transportation Department, Office of University Research, Washington, D.C.

Wide Area Detection System (WADS) - breadboard software description and field test results. Final report.

Federal Highway Administration, Washington, D.C.

Implementation guidelines for actuated controllers in coordinated systems. Final report.

Texas Department of Transportation, Austin

Methods and procedures to reduce motorist delays in European work zones /

"HPIP/10-00(10M)EW"--P. [4] of cover.

Evaluation of warning and information systems. Part II, commercial radio advisories. Final report.

Federal Highway Administration, Washington, D.C.

Evaluation of techniques for reducing in-use automobile fuel consumption. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Mobility impacts from improvements to an arterial street /

"September 1990."