An Economic Analysis of Drawing Lines in the Sea

It is shown that low dispute costs relative to expected resource rents from oceanic resources favor drawn out disputes over maritime boundaries; asymmetric dispute costs favor agreement on boundaries wanted by the low dispute cost state party; and high symmetric dispute costs favor formation of joint development zones. The fact that most maritime boundaries have not yet been drawn suggests that state parties think that resource rents that can be drawn from the oceans are high relative to dispute costs. Moreover, the recent mini-trend towards JDZs in East Asia suggests that state parties in the area have recently reassessed dispute costs as being higher than previously believed.

Box Corer (engineering detail drawing of the large version)

The Box corer is a marine geological and biological sampling tool for soft sediments in lakes or oceans. It is deployed from a research vessel with a deep sea wire and suitable for any water depth. It is designed for a minimum of disturbance of the sediment surface by bow wave effects which is important for quantitative investigations of the benthos micro- to macrofauna, geochemical processes, sampling of bottom water or sedimentology. The large box corer version with an area of 2,500 cm? is frequently used on research vessels since the 1980th years. This data set is a publication of the engeneering drawings.

El dibujo y la vida de los edificios. Drawing and Building Life.

En la encrucijada y debate actual sobre la aplicación de los nuevos medios en la documentación de la Arquitectura, se destaca la necesidad de preservar los valores de la tradición del dibujo arquitectónico, proponiendo su papel nuclear en el concepto de Vida Gráfica como lugar de integración de los nuevos medios y los añejos fines para el progreso en el conocimiento y difusión de la Arquitectura.

Development and Assessment of the Competence Creativity Applied to Technical Drawing

The results obtained after incorporating the competence “creativity” to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students’ creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application

Tutorial 2.0 on Technical Drawing 3D and Visualization

In recent years, the continuous incorporation of new technologies in the learning process has been an important factor in the educational process [1]. The Technical University of Madrid (UPM) promotes educational innovation processes and develops projects related to the improvement of the education quality. The experience that we present fits into the Educational Innovation Project (EIP) of the E.U. of Agricultural Engineering of Madrid. One of the main objectives of the EIP is to "Take advantage of the new opportunities offered by the Learning and Knowledge Technologies in order to enrich the educational processes and teaching management" [2].

Evolution of microstructure, macrotexture and mechanical properties of commercially pure Ti during ECAP-conform processing and drawing

Long-length ultrafine-grained (UFG) Ti rods are produced by equal-channel angular pressing via the conform scheme (ECAP-C) at 200 °C, which is followed by drawing at 200 °C. The evolution of microstructure, macrotexture, and mechanical properties (yield strength, ultimate tensile strength, failure stress, uniform elongation, elongation to failure) of pure Ti during this thermo-mechanical processing is studied. Special attention is also paid to the effect of microstructure on the mechanical behavior of the material after macrolocalization of plastic flow. The number of ECAP-C passes varies in the range of 1–10. The microstructure is more refined with increasing number of ECAP-C passes. Formation of homogeneous microstructure with a grain/subgrain size of 200 nm and its saturation after 6 ECAP-C passes are observed. Strength properties increase with increasing number of ECAP passes and saturate after 6 ECAP-C passes to a yield strength of 973 MPa, an ultimate tensile strength of 1035 MPa, and a true failure stress of 1400 MPa (from 625, 750, and 1150 MPa in the as-received condition). The true strain at failure failure decreases after ECAP-C processing. The reduction of area and true strain to failure values do not decrease after ECAP-C processing. The sample after 6 ECAP-C passes is subjected to drawing at 200¯C resulting in reduction of a grain/subgrain size to 150 nm, formation of (10 1¯0) fiber texture with respect to the rod axis, and further increase of the yield strength up to 1190 MPa, the ultimate tensile strength up to 1230 MPa and the true failure stress up to 1600 MPa. It is demonstrated that UFG CP Ti has low resistance to macrolocalization of plastic deformation and high resistance to crack formation after necking.