Microstructure and corrosion resistance of inorganic-organic (ZrO2-PMMA) hybrid coating on stainless steel

Zirconia-polymethylmetacrylate hybrids prepared by a sol-gel method were deposited by dip-coating on stainless steel to improve the resistance against wet corrosion. The effect of the concentration of polymethylmetacrylate and the number of coating applications on the microstructure and corrosion performance of coated samples was investigated. The microstructural properties of samples was analyzed by scanning electron and atomic force microscopy, adhesion tests and profilemeter measurements. The electrochemical corrosion was evaluated through potentiodynamic polarization curves at room temperature. Results show that the sample prepared with 17 vol.% of polymethylmethacrylate has a maximum corrosion resistance, smaller roughness, are hermetic and adherent to the substrate. This film increases the life time of the stainless steel by a factor 30. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Evaluation of a larval development assay for the detection of anthelmintic resistance in Ostertagia circumcincta

Two experiments were carried out to evaluate a larval development assay for the detection of anthelmintic resistance in O. circumcincta. In Experiment I, the dose responses to levamisole (LEV), thiabendazole (TBZ) and ivermectin (IVM) of 8 isolates of O. circumcincta were measured 34 days after infection (DAI). Four of these isolates were shown to be resistant to 1 or more anthelmintics. With 2 exceptions, all isolates considered to be resistant had higher LD50 values than the susceptible isolates for that anthelmintic. One exception was isolate RM8, which was considered to be resistant to all 3 anthelmintics based on faecal egg count reduction tests in goats, but the LD50 value for LEV did not differ from that for the susceptible isolates. The other exception was an isolate considered to be susceptible to TBZ which had a relatively high LD50 value. In an unrelated trial that was prompted by this finding, this isolate was confirmed to be benzimidazole-resistant. Isolate RM8 and an isolate susceptible to all 3 anthelmintics (SK2) were used in the second experiment, which was conducted to monitor changes in the LD50 values of LEV, TBZ and IVM over time following a single infection of 35 000 infective larvae in young sheep. Faecal samples were collected weekly from 24 to 115 DAI. With all 3 anthelmintics, the LD50 values increased with time to a peak around 50-60 DAI, and then declined to levels similar to those observed soon after patency. This trend was consistent for both isolates. The highest mean LD50 values for isolates SK2 for IVM and TBZ and RM8 for IVM and RM8, respectively, were 1.7 and 1.8 times, and 2.2 and 2.9 times higher than the initial mean LD50 values. There was a clear distinction in LD50 values between isolates at each sampling day for both IVM and TBZ. However, as a consequence of the changes in LD50 values with time, the peak LD50 values of IVM for isolate SK2 were higher than the minimum LD50 values of isolate RM8. As there was no apparent difference in LEV efficacy between these 2 isolates, the data were pooled. The highest mean LD50 value was 2.3 times higher than the initial LD50 value. (C) 1997 Australian Society for Parasitology.

Comparative Study of the Mechanical Resistance of 2 Separate Plates and 2 Overlaid Plates Used in the Fixation of the Mandibular Condyle: An In Vitro Study

Purpose: The objective of this study was to carry out a comparative evaluation of the mechanical resistance of 2 rigid internal fixation techniques for fractures of the mandibular condyle using miniplates.Materials and Methods: Fort), polyurethane resin replicas of human hemimandibles were used. The hemimandibles were sectioned to simulate a high subcondylar fracture and then stabilized with 2 fixing techniques using 2.0-mm system plates and screws. The fixation techniques were 2 separate 4-hole plates with 8 screws, and 2 overlaid 4-hole plates with 4 screws. Each system was submitted to load tests, with the application of the load in mediolateral and anteroposterior directions in an Instron 4411 universal assay machine (Instron, Norwood, MA).Results: Load values and peak displacement were measured. Means and standard deviations were evaluated by analysis of variance (P < .05) and Tukey tests, in which it was verified that the anteroposterior peak load value was affected by the arrangement of the plates on the models, although no differences were observed between the groups for the mediolateral peak load. The arrangement of the plates did not have any influence on peak displacement. Similarly, the final value of the mediolateral load was not affected by the arrangement of the plates on the model.Conclusion: The experimental model with 2 separate plates was statistically superior to the model with 2 overlaid plates only in relation to anteroposterior peak load. Despite showing superiority in mediolateral peak load and peak displacement, there was no statistical difference between the groups for these parameters. (C) 2009 American Association of Oral and Maxillofacial Surgeons

Resistance to maxillary premolar fractures after restoration of class II preparations with resin composite or ceromer.

OBJECTIVE: The aim of this study was to evaluate the resistance to fracture of intact and restored human maxillary premolars. METHOD AND MATERIALS: Thirty noncarious human maxillary premolars, divided into three groups of 10, were submitted to mechanical tests to evaluate their resistance to fracture. Group 1 consisted of intact teeth. Teeth in group 2 received mesio-occlusodistal cavity preparations and were restored with direct resin composite restorations. Teeth in group 3 received mesio-occlusodistal cavity preparations and were restored with ceromer inlays placed with the indirect technique. After restoration, teeth were stored at 37 degrees C for 24 hours and then thermocycled for 500 cycles at temperatures of 5 degrees C and 55 degrees C. RESULTS: Statistical analysis revealed that group 3 (178.765 kgf) had a significantly greater maximum rupture load than did group 1 (120.040 kgf). There was no statistically significant difference between groups 1 and 2 or between groups 2 and 3. CONCLUSION: Class II cavity preparations restored with indirect ceromer inlays offered greater resistance to fracture than did intact teeth. The fracture resistance of teeth restored with resin composite was not significantly different from that of either the ceromer or intact teeth.

Effect of resin luting film thickness on fracture resistance of a ceramic cemented to dentin

Purpose: The aim of this study was to evaluate the fracture resistance of ceramic plates cemented to dentin as a function of the resin cement film thickness. Materials and Methods: Ceramic plates (1 and 2 mm thicknesses) were cemented to bovine dentin using resin composite cement. The film thicknesses used were approximately 100, 200, and 300 μm. Noncemented ceramic plates were used as control. Fracture loads (N) were obtained by compressing a steel indenter in the center of the ceramic plates. ANOVA and Tukey tests (α = 0.05) were used for each ceramic thickness to compare fracture loads among resin cement films used. Results: Mean fracture load (N) for 1-mm ceramic plates were: control - 26 (7); 100 μm - 743 (150); 200 μm - 865 (105); 300 μm - 982 (226). Test groups were significantly different from the control group; there was a statistical difference in fracture load between groups with 100 and 300 μm film thicknesses (p < 0.01). Mean fracture load for 2-mm ceramic plates were: control - 214 (111); 100 μm - 1096 (341); 200 μm - 1067 (226); 300 μm - 1351 (269). Tested groups were also significantly different from the control group (p < 0.01). No statistical difference was shown among different film thicknesses. Conclusions: Unluted specimens presented significantly lower fracture resistance than luted specimens. Higher cement film thickness resulted in increased fracture resistance for the 1-mm ceramic plates. Film thickness did not influence the fracture resistance of 2-mm porcelain plates. Copyright © 2007 by The American College of Prosthodontists.

Multiplex PCR use for Staphylococcus aureus identification and oxacillin and mupirocin resistance evaluation

Oxacillin-resistant Staphylococcus aureus represents a serious problem in hospitals worldwide, increasing infected patients' mortality and morbidity and raising treatment costs and internment time. In this study, the results of using the Multiplex PCR technique to amplify fragments of the genes femA (specific-species), mecA (oxacillin resistance) and ileS-2 (mupirocin resistance) were compared with those of tests conventionally used to identify S. aureus isolates and ascertain their resistance to drugs. Fifty S. aureus strains were isolated from patients receiving treatment at UNOESTE University Hospital in Presidente Prudente, SP, Brazil. The 686 bp fragment corresponding to the gene femA was amplified and detected in all the isolates. On the other hand, the 310 bp fragment corresponding to the mecA gene was amplified in 29 (58%) of the isolates. All of the isolates showed sensitivity to mupirocin in the agar diffusion test, which was corroborated by the lack of any amplicon of the 456 bp fragment corresponding to the ileS-2 gene, in the PCR bands. The conventional tests to identify S. aureus and detect resistance to oxacillin and mupirocin showed 100% agreement with the PCR Multiplex results. The use of techniques for rapid and accurate identification of bacteria and assessment of their resistance may be valuable in the control of infection by resistant strains, allowing the rapid isolation and treatment of an infected patient. However, the results demonstrate that traditional phenotypic tests are also reliable, though they take more time.

Influence of bleaching treatment on flexural resistance of hybrid materials.

The aim of this study is to evaluate the flexural resistance of three types of restorative materials: compomer (Freedom), resin-modified glass-ionomer (Vitremer) and composite resin (Esthet-X), observing whether the application of bleaching agent can cause alterations of their flexural properties. Sixty samples were made using a 10 x 1 x 1 mm brass mold, and divided into three groups: G1- Freedom (SDI); G2- Vitremer (3M ESPE); G3- Esthet-X (Dentsply). On half of the samples of each group (10 samples) the bleaching treatment was applied and the other half used as control, was stored in distilled water at a temperature of 37 degrees C. Whiteness HP Maxx bleaching system was applied on the sample surface following the manufacturer's recommendations, simulating the bleaching treatment at the clinic. After this period, a flexural strength (three-point bending) test was conducted using (EMIC DL 1000) machine until the samples fractured. The data were submitted to ANOVA and Tukey tests. Of the restorative materials studied, G3-(87.24 +/- 31.40 MPa) presented the highest flexural strength, followed by G1-(61.67 +/- 21.32 MPa) and G2-(61.67 +/- 21.32 MPa). There was a statistical difference in flexural strength after the bleaching treatment. It was concluded that the use of a beaching agent can promote significant alteration of the flexural strength of these restorative materials.

Resistance against gastrointestinal nematodes in Crioulo Lageano and crossbred Angus cattle in southern Brazil

Gastrointestinal nematode (GIN) infection is a major cause of production losses in cattle. This study was carried out to evaluate the natural resistance against nematode infection in Crioulo Lageano and crossbred Angus male calves. Crioulo Lageano is a local cattle breed in the state of Santa Catarina, in southern Brazil. Ten weaned calves of each breed were grazed together on pasture and naturally infected with nematodes between July 2009 and December 2010. Once every 28 days, we collected fecal and blood samples for parasitological and immunological tests, as well as recording body weights. After 19 samplings, all animals were slaughtered for quantification and identification of GINs. We found that the animals had been infected with the following nematode species, in decreasing order by the mean number of specimens: Trichostrongylus axei, Cooperia punctata, Ostertagia ostertagi, Haemonchus placei, Oesophagostomum radiatum, and Trichuris spp. There were no significant differences between the Crioulo Lageano and crossbred Angus groups in terms of worm burden or nematode fecal egg count, nor in terms of the mean levels of immunoglobulin (G and A) against C. punctata and H. placei antigens, except in IgA mean level in abomasal mucus against H. placei adult worms that was significantly higher in crossbred Angus cattle (p<0.05). At the end of the study, the crossbred Angus cattle were heavier than were the Crioulo Lageano cattle (mean live weight, 507.35 and 390.3. kg, respectively). Comparative parasitological and immunological evaluation revealed no difference between two breeds in terms of their natural resistance against GINs. © 2012 Elsevier B.V.

Influence of convergence angle of tooth preparation on the fracture resistance of Y-TZP-based all-ceramic restorations

Objective: To investigate the influence of the convergence angle of tooth preparation on the fracture load of Y-TZP-based ceramic (YZ-Vita YZ) substructure (SB) veneered with a feldspathic porcelain (VM9-Vita VM9). Methods: Finite element stress analysis (FEA) was performed to examine the stress distribution of the system. Eighty YZ SB were fabricated using a CAD-CAM system and divided into four groups (n = 20), according to the total occlusal convergence (TOC) angle: G6-6° TOC; G12-12° TOC; G20-20° TOC; and G20MOD-20° TOC with modified SB. All SB were veneered with VM9, cemented in a fiber reinforced epoxy resin die, and loaded to failure. Half of the specimens from each group (n = 10) were cyclic fatigued (106 cycles) before testing. Failure analysis was performed to determine the fracture origin. Data were statistically analyzed using Anova and Tukey's tests (α = 0.05). Results: The greatest mean load to fracture value was found for the G20MOD, which was predicted by the FEA. Cyclic fatigue did not significantly affect the load of fracture. Catastrophic failure originating from the internal occlusal surface of the SB was the predominant failure mode, except for G20MOD. Significance: The YZ-VM9 restorations resisted greater compression load than the usual physiological occlusal load, regardless of the TOC angle of preparations. Yet, the G20MOD design produced the best performance among the experimental conditions evaluated. © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Long-term creatine supplementation improves muscular performance during resistance training in older women

This study examined the effects of long-term creatine supplementation combined with resistance training (RT) on the one-repetition maximum (1RM) strength, motor functional performance (e.g., 30-s chair stand, arm curl, and getting up from lying on the floor tests) and body composition (e.g., fat-free mass, muscle mass, and % body fat using DEXA scans) in older women. Eighteen healthy women (64.9 ± 5.0 years) were randomly assigned in a double-blind fashion to either a creatine (CR, N = 9) or placebo (PL, N = 9) group. Both groups underwent a 12-week RT program (3 days week-1), consuming an equivalent amount of either creatine (5.0 g day-1) or placebo (maltodextrin). After 12 week, the CR group experienced a greater (P < 0.05) increase (Δ%) in training volume (+164.2), and 1RM bench press (+5.1), knee extension (+3.9) and biceps curl (+8.8) performance than the PL group. Furthermore, CR group gained significantly more fat-free mass (+3.2) and muscle mass (+2.8) and were more efficient in performing submaximal-strength functional tests than the PL group. No changes (P > 0.05) in body mass or % body fat were observed from pre- to post-test in either group. These results indicate that long-term creatine supplementation combined with RT improves the ability to perform submaximal-strength functional tasks and promotes a greater increase in maximal strength, fat-free mass and muscle mass in older women. © 2012 Springer-Verlag Berlin Heidelberg.

Effects of resistance training on the performance of activities of daily living in patients with Alzheimer's disease

Aim: The objective of this study was to investigate the effects of resistance training in activities of daily living performance in Alzheimer's disease (AD) patients. Methods: An exploratory and longitudinal study, lasting for 16weeks, with the participation of 34 patients divided equally in: the training group (TG), who participated in a resistance training protocol (three sets of 20 repetitions in five exercises); and the social gathering group (SGG), who participated in a social interaction protocol (i.e. group dynamics, writing and reading activities). Results: We observed significant differences between the groups in moving around the house, climbing stairs, standing up from the floor and putting on socks tests. Conclusion: This study showed that resistance training improves agility, lower limb strength, balance and flexibility in AD patients, while SGG protocol is important to improve the agility. © 2012 Japan Geriatrics Society.

Periapical lesions decrease insulin signal and cause insulin resistance

Introduction: Inflammatory cytokines are associated with decreased insulin signal transduction. Moreover, local oral inflammation, such as that accompanying periodontal disease, is associated with insulin resistance and type 2 diabetes mellitus. The aim of this study was to evaluate the effect of periapical lesions (PLs) on insulin signaling and insulin sensitivity in rats. We hypothesized that PLs alter systemic insulin signaling and insulin sensitivity via elevated plasmatic tumor necrosis factor α (TNF-α). Methods: Wistar rats were divided into control (CN) and PL groups. PLs were induced by exposing pulpal tissue to the oral environment. After 30 days, insulin sensitivity was measured using the insulin tolerance test. After euthanization, maxillae were processed for histopathology. Plasmatic concentrations of tumor necrosis factor α (TNF-α) were determined via the enzyme-linked immunosorbent assay. Insulin signal transduction was evaluated using insulin receptor substrate tyrosine phosphorylation status and serine phosphorylation status in periepididymal white adipose tissue via Western blotting. For insulin signaling and insulin tolerance tests, the analyses performed were analysis of variance followed by the Tukey post hoc test. For TNF-α analysis, the Student's t test was used. In all tests, P <.05 was considered significant. Results: The rats with PLs showed higher plasmatic TNF-α, lower constant rate for glucose disappearance values, and reduced pp185 tyrosine phosphorylation status but no change in serine phosphorylation status in white adipose tissue after insulin stimulation. Conclusions: PLs can cause alterations to both insulin signaling and insulin sensitivity, probably because of elevation of plasmatic TNF-α. The results from this study emphasize the importance of the prevention of local inflammatory diseases, such as PLs, with regard to the prevention of insulin resistance. Copyright © 2013 American Association of Endodontists.

Effects of high temperature plasma immersion ion implantation on wear resistance of Ti-Si-B sintered alloys

Although titanium and its alloys own good mechanical properties and excellent corrosion resistance, these materials present poor tribological properties for specific applications that require wear resistance. In order to produce wear-resistant surfaces, this work is aimed at achieving improvement of wear characteristics in Ti-Si-B alloys by means of high temperature nitrogen plasma immersion ion implantation (PIII). These alloys were produced by powder metallurgy using high energy ball milling and hot pressing. Scanning electron microscopy (SEM) and X-ray diffraction identified the presence of α-titanium, Ti6Si2B, Ti5Si3, TiB and Ti3Si phases. Wear tests were carried out with a ball-on-disk tribometer to evaluate the friction coefficient and wear rate in treated and untreated samples. The worn profiles were measured by visible light microscopy and examined by SEM in order to determine the wear rates and wear mechanisms. Ti-7.5Si-22.5B alloy presented the highest wear resistance amongst the untreated alloys produced in this work. High temperature PIII was effective to reduce the wear rate and friction coefficient of all the Ti-Si-B sintered alloys. © 2013 Elsevier B.V.

Characterization of cowpea genotype resistance to Callosobruchus maculatus

The objective of this work was to characterize the resistance of 50 cowpea (Vigna unguiculata) genotypes to Callosobruchus maculatus. A completely randomized design with five replicates per treatment (genotype) was used. No-choice tests were performed using the 50 cowpea genotypes to evaluate the preference for oviposition and the development of the weevil. The genotypes IT85 F-2687, MN05-841 B-49, MNC99-508-1, MNC99-510-8, TVu 1593, Canapuzinho-1-2, and Sanzi Sambili show non-preference-type resistance (oviposition and feeding). IT81 D-1045 Ereto and IT81 D-1045 Enramador exhibit antibiosis against C. maculatus and descend from resistant genitors, which grants them potential to be used in future crossings to obtain cowpea varieties with higher levels of resistance.