"Powder Puffs" (1967)

Part of Brock's first ever all female crew.

X-ray diffraction from Al powder using energy dispersive technique

Using the energy dispersive x ...ray diffraction (EDXD) technique, the room temperature diffraction pattern of Al powder was obtained at diffraction angles ~ 30° and 50°. From the small angle diffraction pattern the average relative intensities (IR) of the (111), (200), and (220) lines were measured to be equal to 100, 62, and 32 respectively. From the large diffraction angle IR for the (220), (311+222), (400), (331+420), and (422) lines were measured to be 100,201,17,90, and 19.5 respectively. The diffraction pattern at those two angles were obtained at several higher temperatures to measure the change in the intensities of the Al lines. From the intensity changes the increase of the Debye- Waller temperature factor, i.e ~B(T), with respect to the value at room temperature was determined to be 0.6+0.1 at 250°C, 1.10+0.15 at 350°C, 1.45+0.20 at 450°C, and 2.20±0.35 at 550°C.

Article - "Dorothy First at Wichita in 'Powder Puff' Derby"

An article in the Toronto Star written by Dorothy Rungeling during the 'Powder Puff' Derby. She is reporting from the Wichita, Kansas leg of the race and remarks about her time in California.

Article - "Dorothy Rungeling Enters "Powder Puff" Air Derby, 1958

An article about Dorothy Rungeling in her third Derby competition in 1958. She will be co-piloted by Miss Susan Koch and the route will take them from San Diego, California to Charleston, South Carolina.

Etude spectroscopique d’un plasma micro-onde à la pression atmosphérique et son application à la synthèse de nanostructures

L’objectif de ce mémoire de maîtrise est de caractériser la distribution axiale des plasmas tubulaires à la pression atmosphérique créés et entretenus par une onde électromagnétique de surface ainsi que d’explorer le potentiel de ces sources pour la synthèse de matériaux et de nanomatériaux. Un précédent travail de thèse, qui avait pour objectif de déterminer les mécanismes à l’origine de la contraction radiale du plasma créé dans des gaz rares, a mis en lumière un phénomène jusque-là inconnu dans les plasmas d’onde de surface (POS). En effet, la distribution axiale varie différemment selon la puissance incidente ce qui constitue une différence majeure par rapport aux plasmas à pression réduite. Dans ce contexte, nous avons réalisé une étude paramétrique des POS à la pression atmosphérique dans l’Ar. À partir de nos mesures de densité électronique, de température d’excitation et de densité d’atomes d’Ar dans un niveau métastable (Ar 3P2), résolues axialement, nous avons conclu que le comportement axial de l’intensité lumineuse avec la puissance n’est pas lié à un changement de la cinétique de la décharge (qui est dépendante de la température des électrons et de la densité d’atomes d’Ar métastables), mais plutôt à une distribution anormale de dissipation de puissance dans le plasma (reliée à la densité d’électrons). Plus précisément, nos résultats suggèrent que ce dépôt anormal de puissance provient d’une réflexion de l’onde dans le fort gradient de densité de charges en fin de colonne, un effet plus marqué pour de faibles longueurs de colonnes à plasma. Ensuite, nous avons effectué une étude spectroscopique du plasma en présence de précurseurs organiques, en particulier le HMDSO pour la synthèse de matériaux organosiliciés et l’IPT pour la synthèse de matériaux organotitaniques. Les POS à la PA sont caractérisés par des densités de charges très élevées (>10^13 cm^-3), permettant ainsi d’atteindre des degrés de dissociation des précurseurs nettement plus élevés que ceux d'autres plasmas froids à la pression atmosphérique comme les décharges à barrière diélectrique. Dans de tels cas, les matériaux synthétisés prennent la forme de nanopoudres organiques de taille inférieure à 100 nm. En présence de faibles quantités d’oxygène dans le plasma, nous obtenons plutôt des nanopoudres à base d’oxyde de silicium (HMDSO) ou à base de titanate de silicium (IPT), avec très peu de carbone.

Nouveaux complexes pinces POCOP, NHCCOP, PIMCOP et PIMIOCOP, et complexes cyclométallés de Ni(II) : synthèse, caractérisation et réactivité.

Cette thèse traite de la chimie des complexes pinces de Ni(II) ainsi que des complexes cyclométallés de Ni(II) comportant au moins un motif phosphinite. Elle se divise en trois parties. La première concerne la synthèse, la caractérisation, le mécanisme de formation et la réactivité des complexes pinces de Ni(II) à base de ligand de type POCOP 1,3-(i-Pr2PO)2C6H4. De nouveaux ligands de type R-(POCOP) = κP,κC,κP-{Rn-2,6-( R'2PO)2C6H4-n}; Rn = 4-OMe, 4-Me, 4-CO2Me, 3-OMe, 3- CO2Me, 3,5-t-Bu2 ; R' = i-Pr, t-Bu ont été synthétisés suite à l'addition de chlorophosphine ClPR'2 à une solution de résorcinol ou dérivés en présence de base. La synthèse des complexes R-(POCOP)Ni(Br) s'effectue à partir du ligand correspondant en présence de base, et de {NiBr2(NCiPr)}n. Ce nouveau précurseur de nickel est synthétisé à partir de brome de nickel métallique dans l'isobutyronitrile. Il est stable sous atmosphère inerte et sa solubilité dans les solvants polaires permet d'étudier les synthèses des complexes en milieu homogène. Le mécanisme de formation des complexes portant des ligand pinces (PCsp3P) 1,3-(i- Pr2PCH2CH2)2CH2, (POCsp3OP) 1,3-(i-Pr2POCH2)2CH2, (PCsp2P) 1,3-(i- Pr2PCH2)2C6H4, Rn-(POCsp2OP) 1,3-(i-Pr2PO)2C6H4-n via nickellation du lien C-H a été investigué avec une méthode de réaction de compétition. Cette étape a été déterminée comme étant de nature électrophile. Les complexes résultants ont été complètement caractérisés. Une corrélation a notamment été effectuée entre le déplacement chimique du Cipso en spectroscopie RMN 13C et le potentiel d'oxydation Eox en voltamétrie cyclique. Une nouvelle méthode de synthèse directe verte "one pot" a été mise en place. En faisant réagir à 75 °C un mélange hétérogène de II résorcinol, de chlorodiisopropylphosphine et de nickel métallique en poudre, on obtient le complexes pince (POCOP)Ni(Cl) avec des rendements allant jusqu'à 93%. La réactivité de ces complexes POCOP a été investiguée pour des réactions de fluorination et trifluorométhylation des halogénures d'alkyle. La synthèse du (POCOP)Ni(F) a lieu à partir de précurseur (POCOP)Ni(X) (X=Br, Cl), en présence d'un large excès de fluorure d'argent AgF. Ce complexe catalyse la fluorination du bromure de benzyle et peut être converti en (POCOP)Ni(CF3) en présence de réactif du Ruppert, Me3SiCF3. La réaction entre (POCOP)Ni(CF3) et le bromure de benzyle dans les solvants aromatiques mène à la conversion totale du complexe en (POCOP)Ni(Br) et à l'inattendue benzylation du solvant aromatique utilisé. La seconde partie concerne la synthèse des nouveaux complexes non symétriques à base de ligands comportant un motif imidazolo-phosphine (PIMCOP) 3-[2-(R2P)-C3H2N2]-(R2PO)-C6H3, imidazoliophosphine (PIMIOCOP) 3-[2-(R2P)-3- (CH3)-C3H2N2]-(R2PO)-C6H3] et carbène N-hétérocyclique (NHCCOP). La double déprotonation du 3-hydroxyphenyl-imidazole suivi de l'addition de deux équivalents de chlorodiphenylphosphine mène à l'obtention du ligand PIMCOP 3-[3-(CH3)- C3H2N2]-(R2PO)-C6H3. L'étape de nickellation a lieu comme dans le cas des composés (POCOP)Ni. La méthylation du motif imidazole du (PIMCOP)Ni(Br) par le triflate de méthyle MeOTf, donne le dérivé (PIMIOCOP)Ni(Br). Ce dernier est converti en (NHCCOP)Ni(Br) après l'addition de chlorure de tétraéthylamonium NEt4Cl. Les analogues i-Pr2P de ces complexes sont synthétisés en remplaçant ClPPh2 par ClPiPr2. On obtient les espèces cationiques [(PIMCOP)Ni(NCCH3)][OTf], [(PIMIOCOP)Ni(NCCH3)][OTf]2 et III [(NHCCOP)Ni(NCCH3)][OTf] suite à l'addition en solution dans l'acétonitrile de triflate d'argent AgOTf. Ces espèces ont été utilisés comme catalyseurs pour la synthèse d'amidine à partir de benzonitrile et de diverse amines aliphatiques. Enfin des complexes orthonickellés trans-Ni[(ĸ2-P,C-P(OC6H4)-(iPr2)( iPr2P(OC6H5))]Br à base de phosphinite ont été synthétisés et caractérisés. Les ligands sont synthétisés par réaction d'un phénol et de chlorodiisopropylphosphine en présence de base. L'ajout de {NiBr2(NCiPr)}n et de triéthylamine permet l'orthométallation via une étape de nickellation C-H. Un intermédiaire trans- [NiBr2{PiPr2(OC6H5)}2] de cette réaction a été isolé. Le complexe dimère peut réagir avec des espèces électrophiles mener à l'ortho-fonctionnalisation de la phosphinite.

Photoacoustic spectrum of samarium phthalocyanine powder

Photoacoustic spectrum of samarium phthalocyanine powder is recorded and compared with previously reported UV–vis absorption spectra of the same dissolved in different liquid and solid host media. The Davidov splitting of Q band is observed in the PA spectrum but the two bands are overlapped considerably and the shorter wavelength band is more intense and dominating one in the powder spectrum.

Precursor nanoscale modulations in ferromagnets: Modeling and thermodynamic characterization

Using a Ginzburg-Landau model for the magnetic degrees of freedom with coupling to disorder, we demonstrate through simulations the existence of stripelike magnetic precursors recently observed in Co-Ni-Al alloys above the Curie temperature. We characterize these magnetic modulations by means of the temperature dependence of local magnetization distribution, magnetized volume fraction, and magnetic susceptibility. We also obtain a temperature-disorder strength phase diagram in which a magnetic tweed phase exists in a small region between the paramagnetic and dipolar phases.

Studies on electroluminescence using Powder and thin film devices

The subject of electroluminescence has currently acquired great importance because of its potential applications in display systems of a wide variety. A large number of scientists working in commercial, governmental as well as academic institutions all over the world are at present engaged in the intense effort to develop new and efficient phosphor materials and electroluminescent devices. This thesis presents the work carried out by the author in this field during the past few years. The studies discussed in this thesis are mostly confined to the development of some new phosphor materials, their uses in powder and thin film electroluminescent devices and to their electrical and spectral characteristics. Care has been taken to bring' out the physics involved in all the above aspects of the phenomenon

An investigation on the effects of Ag addition in the powder — in tube processing of long multifilamentary (Bi,Pb) - 2223/Ag superconducting tapes

It is important that long superconducting tape must have desired strain tolerance (less reduction of Jc with applied strains) and stress tolerance (less reduction of JC in applied stresses) for its use as coils and magnets. Ag addition to the BPSCCO system has many advantages with its physical and chemical inertness to the system, reduces the processing temperature, and promotes the grain growth, grain alignment and connectivity. All these not only enhance the critical current density of the tapes but also improve the mechanical properties. But the published results show very much scattering on the type of Ag additive to be selected, method of addition and its optimum percentage. Also there are some negative reports in this regard. The present work has been undertaken to study the effect of silver addition in different forms (Ag powder, Ag2O, AgNO3) on the superconducting and mechanical properties of (Bi,Pb)-2223/Ag tapes and to find out a suitable form of Ag additive and its optimum percentage to have better superconducting and mechanical properties. Also it is the aim of the present work is to optimise the process parameters needed to prepare (Bi,Pb)-2223/Ag multifilamentary tapes of length ~ 12 m in solenoid and pancake coil forms with good critical current density and homogeneity of J C along the length of the tapes.

CuInS2/In2S3 Cells using a Cost-effective Technique: Significance of Precursor Ratios on Cell Parameters

Thin film solar cells having structure CuInS2/In2S3 were fabricated using chemical spray pyrolysis (CSP) technique over ITO coated glass. Top electrode was silver film (area 0.05 cm2). Cu/In ratio and S/Cu in the precursor solution for CuInS2 were fixed as 1.2 and 5 respectively. In/S ratio in the precursor solution for In2S3 was fixed as 1.2/8. An efficiency of 0.6% (fill factor -37.6%) was obtained. Cu diffusion to the In2S3 layer, which deteriorates junction properties, is inevitable in CuInS2/In2S3 cell. So to decrease this effect and to ensure a Cu-free In2S3 layer at the top of the cell, Cu/In ratio was reduced to 1. Then a remarkable increase in short circuit current density was occurred from 3 mA/cm2 to 14.8 mA/cm2 and an efficiency of 2.13% was achieved. Also when In/S ratio was altered to 1.2/12, the short circuit current density increased to 17.8 mA/cm2 with an improved fill factor of 32% and efficiency remaining as 2%. Thus Cu/In and In/S ratios in the precursor solutions play a crucial role in determining the cell parameters

New studies on the versatile roles of Polyaniline and its composites in polymer based optoelectronic and energy storage devices

From the early stages of the twentieth century, polyaniline (PANI), a well-known and extensively studied conducting polymer has captured the attention of scientific community owing to its interesting electrical and optical properties. Starting from its structural properties, to the currently pursued optical, electrical and electrochemical properties, extensive investigations on pure PANI and its composites are still much relevant to explore its potentialities to the maximum extent. The synthesis of highly crystalline PANI films with ordered structure and high electrical conductivity has not been pursued in depth yet. Recently, nanostructured PANI and the nanocomposites of PANI have attracted a great deal of research attention owing to the possibilities of applications in optical switching devices, optoelectronics and energy storage devices. The work presented in the thesis is centered around the realization of highly conducting and structurally ordered PANI and its composites for applications mainly in the areas of nonlinear optics and electrochemical energy storage. Out of the vast variety of application fields of PANI, these two areas are specifically selected for the present studies, because of the following observations. The non-linear optical properties and the energy storing properties of PANI depend quite sensitively on the extent of conjugation of the polymer structure, the type and concentration of the dopants added and the type and size of the nano particles selected for making the nanocomposites. The first phase of the work is devoted to the synthesis of highly ordered and conducting films of PANI doped with various dopants and the structural, morphological and electrical characterization followed by the synthesis of metal nanoparticles incorporated PANI samples and the detailed optical characterization in the linear and nonlinear regimes. The second phase of the work comprises the investigations on the prospects of PANI in realizing polymer based rechargeable lithium ion cells with the inherent structural flexibility of polymer systems and environmental safety and stability. Secondary battery systems have become an inevitable part of daily life. They can be found in most of the portable electronic gadgets and recently they have started powering automobiles, although the power generated is low. The efficient storage of electrical energy generated from solar cells is achieved by using suitable secondary battery systems. The development of rechargeable battery systems having excellent charge storage capacity, cyclability, environmental friendliness and flexibility has yet to be realized in practice. Rechargeable Li-ion cells employing cathode active materials like LiCoO2, LiMn2O4, LiFePO4 have got remarkable charge storage capacity with least charge leakage when not in use. However, material toxicity, chance of cell explosion and lack of effective cell recycling mechanism pose significant risk factors which are to be addressed seriously. These cells also lack flexibility in their design due to the structural characteristics of the electrode materials. Global research is directed towards identifying new class of electrode materials with less risk factors and better structural stability and flexibility. Polymer based electrode materials with inherent flexibility, stability and eco-friendliness can be a suitable choice. One of the prime drawbacks of polymer based cathode materials is the low electronic conductivity. Hence the real task with this class of materials is to get better electronic conductivity with good electrical storage capability. Electronic conductivity can be enhanced by using proper dopants. In the designing of rechargeable Li-ion cells with polymer based cathode active materials, the key issue is to identify the optimum lithiation of the polymer cathode which can ensure the highest electronic conductivity and specific charge capacity possible The development of conducting polymer based rechargeable Li-ion cells with high specific capacity and excellent cycling characteristics is a highly competitive area among research and development groups, worldwide. Polymer based rechargeable batteries are specifically attractive due to the environmentally benign nature and the possible constructional flexibility they offer. Among polymers having electrical transport properties suitable for rechargeable battery applications, polyaniline is the most favoured one due to its tunable electrical conducting properties and the availability of cost effective precursor materials for its synthesis. The performance of a battery depends significantly on the characteristics of its integral parts, the cathode, anode and the electrolyte, which in turn depend on the materials used. Many research groups are involved in developing new electrode and electrolyte materials to enhance the overall performance efficiency of the battery. Currently explored electrolytes for Li ion battery applications are in liquid or gel form, which makes well-defined sealing essential. The use of solid electrolytes eliminates the need for containment of liquid electrolytes, which will certainly simplify the cell design and improve the safety and durability. The other advantages of polymer electrolytes include dimensional stability, safety and the ability to prevent lithium dendrite formation. One of the ultimate aims of the present work is to realize all solid state, flexible and environment friendly Li-ion cells with high specific capacity and excellent cycling stability. Part of the present work is hence focused on identifying good polymer based solid electrolytes essential for realizing all solid state polymer based Li ion cells.The present work is an attempt to study the versatile roles of polyaniline in two different fields of technological applications like nonlinear optics and energy storage. Conducting form of doped PANI films with good extent of crystallinity have been realized using a level surface assisted casting method in addition to the generally employed technique of spin coating. Metal nanoparticles embedded PANI offers a rich source for nonlinear optical studies and hence gold and silver nanoparticles have been used for making the nanocomposites in bulk and thin film forms. These PANI nanocomposites are found to exhibit quite dominant third order optical non-linearity. The highlight of these studies is the observation of the interesting phenomenon of the switching between saturable absorption (SA) and reverse saturable absorption (RSA) in the films of Ag/PANI and Au/PANI nanocomposites, which offers prospects of applications in optical switching. The investigations on the energy storage prospects of PANI were carried out on Li enriched PANI which was used as the cathode active material for assembling rechargeable Li-ion cells. For Li enrichment or Li doping of PANI, n-Butyllithium (n-BuLi) in hexanes was used. The Li doping as well as the Li-ion cell assembling were carried out in an argon filled glove box. Coin cells were assembled with Li doped PANI with different doping concentrations, as the cathode, LiPF6 as the electrolyte and Li metal as the anode. These coin cells are found to show reasonably good specific capacity around 22mAh/g and excellent cycling stability and coulombic efficiency around 99%. To improve the specific capacity, composites of Li doped PANI with inorganic cathode active materials like LiFePO4 and LiMn2O4 were synthesized and coin cells were assembled as mentioned earlier to assess the electrochemical capability. The cells assembled using the composite cathodes are found to show significant enhancement in specific capacity to around 40mAh/g. One of the other interesting observations is the complete blocking of the adverse effects of Jahn-Teller distortion, when the composite cathode, PANI-LiMn2O4 is used for assembling the Li-ion cells. This distortion is generally observed, near room temperature, when LiMn2O4 is used as the cathode, which significantly reduces the cycling stability of the cells.