Influence of spray drying operating conditions on microencapsulated rosemary essential oil properties

Spray drying is an important method used by the food industry in the production of microencapsulated flavors to improve handling and dispersion properties. The objective of this study was to evaluate the influence of the process conditions on the properties of rosemary essential oil microencapsulated by spray drying using gum Arabic as encapsulant. The effects of the wall material concentration (10-30%), inlet air temperature (135-195 ºC), and feed flow rate (0.5-1.0 L.h-1) on the moisture content, hygroscopicity, wettability, solubility, bulk and tapped densities, particle density, flowability, and cohesiveness were evaluated using a 2³ central composite rotational experimental design. Moisture content, hygroscopicity and wettability were significantly affected by the three factors analyzed. Bulk density was positively influenced by the wall material concentration and negatively by the inlet air temperature. Particle density was influenced by the wall material concentration and the inlet air temperature variables, both in a negative manner. As for the solubility, tapped density, flowability, and cohesiveness, the models did not fit the data well. The results indicated that moderate wall material concentration (24%), low inlet air temperature (135 ºC), and moderate feed flow rate (0.7 L.h-1) are the best spray drying conditions.

Foreign exchange exposure management in a fuel procurement company operating in the commodity markets

Fluctuating commodity prices, foreign exchange rates and interest rates are causing changes in cash flows, market value and the companies’ profit. Most of the commodities are quoted in US dollar. Companies with non-dollar accounting face a double risk in the form of the commodity price risk and foreign exchange risk. The objective of this Master’s thesis is to find out how companies under commodity should manage foreign exchange exposure. The theoretical literature is based on foreign exchange risk, commodity risk and foreign exchange exposure management. The empirical research is done by using constructive modelling of a case company in the oil industry. The exposure is model with foreign exchange net cash flow and net working capital. First, the factors affecting foreign exchange exposure in case company are analyzed, then a model of foreign exchange exposure is created. Finally, the models are compared and the most suitable method is defined. According to the literature, foreign exchange exposure is the foreign exchange net cash flow. However, the results of the study show that foreign exchange risk can be managed also with net working capital. When the purchases, sales and storage are under foreign exchange risk, the best way to manage foreign exchange exposure is with combined net cash flow and net working capital method. The foreign exchange risk policy of the company defines the appropriate way to manage foreign exchange risk.

The role of nuclear and other conventional power plants in the flexible energy system

This thesis reviews the role of nuclear and conventional power plants in the future energy system. The review is done by utilizing freely accesible publications in addition to generating load duration and ramping curves for Nordic energy system. As the aim of the future energy system is to reduce GHG-emissions and avoid further global warming, the need for flexible power generation increases with the increased share of intermittent renewables. The goal of this thesis is to offer extensive understanding of possibilities and restrictions that nuclear power and conventional power plants have regarding flexible and sustainable generation. As a conclusion, nuclear power is the only technology that is able to provide large scale GHG-free power output variations with good ramping values. Most of the currently operating plants are able to take part in load following as the requirement to do so is already required to be included in the plant design. Load duration and ramping curves produced prove that nuclear power is able to cover most of the annual generation variation and ramping needs in the Nordic energy system. From the conventional power generation methods, only biomass combustion can be considered GHG-free because biomass is considered carbon neutral. CFB combusted biomass has good load follow capabilities in good ramping and turndown ratios. All the other conventional power generation technologies generate GHG-emissions and therefore the use of these technologies should be reduced.

Internal Changes in International New Ventures During Initial Internationalization: Finnish SMEs Operating in Dynamic High-tech Industries

The purpose of this qualitative research is to study how international new ventures change internally during initial internationalization. Based on the analysis of seven INV firms, a framework illustrating this change process, will be developed. This research will also develop earlier theories, and create a solid combination of existing theories to explain the phenomenon. INV firms internationalize more rapidly and aggressively than traditional MNEs. At the same, external and internal drivers cause changes in INVs culture, resources, capabilities, strategic management, and output decisions inside the company. Organizational learning and resource acquisition through international business networks explain how INVs are able to cope with the dynamic high-technology industry and be able to adapt. Internationalization of INVs proceeds through several phases, which may be gone through rapidly due to the network effects and INVs’ special characteristics. The results of this research revealed that INVs internal change process proceeds through four phases; pre-incorporation phase, product development phase, internationalization and growth phase, and maturation phase. INVs culture, resources, capabilities, strategic management, and outputs change significantly during initial internationalization, and INVs develop from small start-ups into fully established companies.

Co-creating Value For Smart Phone Operating Systems Via Virtual Discussion Forums

In the traditional way, value is created by manufacturer or producer of a product without engaging the customers. So, traditionally value creation is a monopoly in the part of a manufacturer. After gathering all the raw materials the manufacturers are inserting value to a product. And the inserted value is recognized in the time of consuming the product. In the modern time though there is traditional way of value creation but with the increase of more educated, smart, and technically sound customers the idea of value creation has changed. Now, customers are also contributing in value creation as value co-creator even before the product is consumed. This scenario has been encountered in the thesis with the main purpose of how value is cocreated in smart phone operating systems. The purpose is further divided into the following supobjectives: o What is value co-creation in smart phone operating systems? o Who participates in value co-creation in smart phone operating systems? o What are the procedures that are involved in value co-creation in smart phone operating systems? The research was conducted as a qualitative desk study by observing two of the leading smart phone operating system providers. Data has been collected from the official discussion forum of both the operating system providers. Other general concepts relating to the purpose of the study has been encountered through literature review. The research findings reveal that customers and companies both together co-create value of anticipated level when they communicate and interact with each other. However, most of the time customer to customer interactions, dialogues and discussions that come out in the core conversation help the value co-creation. The value co-creation framework sets up the customer at the main focus of value creation theory. By nullifying the inherited notion that companies only create value within its boundary and provide it to their customers in exchange of currencies. Rationally, it has been commenced that the firms are merely compromising value propositions to its customers. But the value has been co-created in a point where offerings are combined and interacted with customers’ capabilities, knowledge, resources and perceptions. This new perspective has radically altered the prospect of firms towards its customers. Typically customers are now taking part in value cocreation as a crucial member.

Evaluation of the Efficiency of Line-Start Permanent-Magnet Machines as a Function of the Operating Temperature

The standard squirrel-cage induction machine has nearly reached its maximum efficiency. In order to further increase the energy efficiency of electrical machines, the use of permanent magnets in combination with the robust design and the line start capability of the induction machine is extensively investigated. Many experimental designs have been suggested in literature, but recently, these line-start permanent-magnet machines (LSPMMs) have become off-the-shelf products available in a power range up to 7.5 kW. The permanent magnet flux density is a function of the operating temperature. Consequently, the temperature will affect almost every electrical quantity of the machine, including current, torque, and efficiency. In this paper, the efficiency of an off-the-shelf 4-kW three-phase LSPMM is evaluated as a function of the temperature by both finite-element modeling and by practical measurements. In order to obtain stator, rotor, and permanent magnet temperatures, lumped thermal modeling is used.

Registered Nurses' Perceptions about Facilitators and Barriers to Maternal Skin to Skin Contact in the Operating Room

Abstract It is recommended that all new mothers experience skin-to-skin contact (SSC) with their newborns immediately after birth. However, SSC is not commonly practiced after cesarean deliveries. To understand facilitators and barriers regarding SSC in the operating room (OR), a descriptive online and paper survey was conducted with 68 Registered Nurses from four hospitals in Ontario. The theory of planned behavior framed the study. Nurses had positive attitudes, and believed most health care team members supported SSC in the OR, but were uncertain about their control over the behavior. Nurses who had practiced the behavior in the past had more positive attitudinal and normative beliefs, and perceived some barriers as less difficult. Attitude and past behavior were the only significant multivariate predictors of intention to practice SSC in the future. Results suggest that shifting attitude and supporting more experience with the practice may increase nurses’ implementation of SSC in the OR.

A Compact Novel Slot-Loaded Dual-Frequency H-Shaped Antenna

A novel compact single-layer dual frequency microstrip antenna which uses an H-shaped geometry with two U-shaped slots embedded near the radiation edges, is presented. By changing the design parameters, the lower and higher resonant frequencies can be controlled easily, and a range of frequency ratios (1.716-2.363) can be obtained in this design. For the two operating frequencies of the proposed antenna, the same polarization planes and broadside radiation patterns are achieved. Compared to the regular dualfrequency patch antenna, this antenna can realize a significant size reduction

Development of a varactor -controlled dual-frequency reconfigurable microstrip antenna

A new design for a compact electronically reconffgurable singlefeed dual frequency dual-polarized operation of a square-microstrip antenna capable of achieving tunable frequency ratios in the range 1.1 to 1.37 is proposed and experimentally studied. Varactor diodes inlegruted with the arms of the hexagonal slot and embedded in the square patch are used to tune the operating frequencies by applying reverse-bias voltage. The design has the advantage of size reduction up to 73.21% and 49.86% for the two resonant frequencies, respectively, as compared to standard rectangular patches. The antenna offers good bandwidth of 5.74% and 5.36% for the two operating frequencies. A highly simplified tuning circuitry without any transmission lines adds to the compactness of the design

Mathematical Modelling of the Dynamics of Granular Materials in a Rotating Cylinder

The current study is aimed at the development of a theoretical simulation tool based on Discrete Element Method (DEM) to 'interpret granular dynamics of solid bed in the cross section of the horizontal rotating cylinder at the microscopic level and subsequently apply this model to establish the transition behaviour, mixing and segregation.The simulation of the granular motion developed in this work is based on solving Newton's equation of motion for each particle in the granular bed subjected to the collisional forces, external forces and boundary forces. At every instant of time, the forces are tracked and the positions velocities and accelarations of each partcle is The software code for this simulation is written in VISUAL FORTRAN 90 After checking the validity of the code with special tests, it is used to investigate the transition behaviour of granular solids motion in the cross section of a rotating cylinder for various rotational speeds and fill fraction.This work is hence directed towards a theoretical investigation based on Discrete Element Method (DEM) of the motion of granular solids in the radial direction of the horizontal cylinder to elucidate the relationship between the operating parameters of the rotating cylinder geometry and physical properties ofthe granular solid.The operating parameters of the rotating cylinder include the various rotational velocities of the cylinder and volumetric fill. The physical properties of the granular solids include particle sizes, densities, stiffness coefficients, and coefficient of friction Further the work highlights the fundamental basis for the important phenomena of the system namely; (i) the different modes of solids motion observed in a transverse crosssection of the rotating cylinder for various rotational speeds, (ii) the radial mixing of the granular solid in terms of active layer depth (iii) rate coefficient of mixing as well as the transition behaviour in terms of the bed turnover time and rotational speed and (iv) the segregation mechanisms resulting from differences in the size and density of particles.The transition behaviour involving its six different modes of motion of the granular solid bed is quantified in terms of Froude number and the results obtained are validated with experimental and theoretical results reported in the literature The transition from slumping to rolling mode is quantified using the bed turnover time and a linear relationship is established between the bed turn over time and the inverse of the rotational speed of the cylinder as predicted by Davidson et al. [2000]. The effect of the rotational speed, fill fraction and coefficient of friction on the dynamic angle of repose are presented and discussed. The variation of active layer depth with respect to fill fraction and rotational speed have been investigated. The results obtained through simulation are compared with the experimental results reported by Van Puyvelde et. at. [2000] and Ding et at. [2002].The theoretical model has been further extended, to study the rmxmg and segregation in the transverse direction for different particle sizes and their size ratios. The effect of fill fraction and rotational speed on the transverse mixing behaviour is presented in the form of a mixing index and mixing kinetics curve. The segregation pattern obtained by the simulation of the granular solid bed with respect to the rotational speed of the cylinder is presented both in graphical and numerical forms. The segregation behaviour of the granular solid bed with respect to particle size, density and volume fraction of particle size has been investigated. Several important macro parameters characterising segregation such as mixing index, percolation index and segregation index have been derived from the simulation tool based on first principles developed in this work.

Studies on the technological aspects and economic efficiency of trawl gear operating along the Cochin coast

Trawling, despite being heavily energy expensive, still continues to be the most energy expensive fishing method particularly so in View of the export oriented nature of the Indian seafood industry. This study therefore aims at analyzing the efficiency of trawls operation from Cochin, an important fishing center along the southwest coast of India. The analysis is made along two perspectives - economic and technological. Even though technological efficiency complement economic efficiency, in the fishing parlance, parameters like the size composition of the catch, selectivity factors, etc., will have a direct bearing on the technological qualities of the trawl, and which parameters will have a significant impact on the effective exploitation of a fishery stock. Whereas the technological analysis aims at improving the efficiency with regard to the effective utilization of fuel and fishery stocks, economic analysis ascertains the present status of the trawling operations from the commercial angle.

The Ratios of Carbon, Nitrogen, and Phosphorus in a Wetland Coastal Ecosystem of Southern India

The fertility of the coastal and estuarine waters is of great concern because of its influence on the productivity of these waters. Seasonal variations in the distribution of organic carbon, total nitrogen and total phosphorus in the sediments of Kuttanad Waters, a part of the tropical Cochin Estuary on the south west coast of India, are examined to identify the contribution of sediments to the fertility of the aquatic systems. The adjoining region has considerable agricultural activity. The fresh water zones had higher quantities of silt and clay whereas the estuarine zone was more sandy. Organic carbon, total phosphorus and total nitrogen were higher in the fresh water zones and lower in the estuarine zones. Total phosphorus and organic carbon showed the lowest values during monsoon periods. No significant trends were observed in the seasonal distributions of total nitrogen. Ratios of C/N, C/P and N/P, and the phosphorus and nitrogen content indicate significant modification in the character of the organic matter. Substantial amounts of the organic matter can contribute to reducing conditions and modify diagenetic processes

CuInS2/In2S3 Cells using a Cost-effective Technique: Significance of Precursor Ratios on Cell Parameters

Thin film solar cells having structure CuInS2/In2S3 were fabricated using chemical spray pyrolysis (CSP) technique over ITO coated glass. Top electrode was silver film (area 0.05 cm2). Cu/In ratio and S/Cu in the precursor solution for CuInS2 were fixed as 1.2 and 5 respectively. In/S ratio in the precursor solution for In2S3 was fixed as 1.2/8. An efficiency of 0.6% (fill factor -37.6%) was obtained. Cu diffusion to the In2S3 layer, which deteriorates junction properties, is inevitable in CuInS2/In2S3 cell. So to decrease this effect and to ensure a Cu-free In2S3 layer at the top of the cell, Cu/In ratio was reduced to 1. Then a remarkable increase in short circuit current density was occurred from 3 mA/cm2 to 14.8 mA/cm2 and an efficiency of 2.13% was achieved. Also when In/S ratio was altered to 1.2/12, the short circuit current density increased to 17.8 mA/cm2 with an improved fill factor of 32% and efficiency remaining as 2%. Thus Cu/In and In/S ratios in the precursor solutions play a crucial role in determining the cell parameters

Operating Systems

From the Brookshear Chapter on Operating Systems