Pilhas a combustível de óxido sólido: materiais, componentes e configurações

In this paper the current status of fuel cells is described with particular emphasis on high (T > 800 ºC) and intermediate (T < 800 ºC) temperature solid oxide fuel cells. Also the importance of the fuel cell technology is shown. Reviewed are the fundamental features, the basic principles, types of fuel cell, fabrication methods, cell configurations and the development of components (cathodes, anodes, electrolytes, interconnect) and materials.

Estudo do efeito de tratamentos térmicos em catalisadores de PtRu/C frente à reação de oxidação de hidrogênio na presença de CO

In this work the effects of time and temperature of thermal treatments under reducing atmosphere (H2) on PtRu/C catalysts for the hydrogen oxidation reaction (HOR) in the presence of CO on a proton exchange membrane fuel cell (PEMFC) single cells have been studied. It can be seen that the increase of the treatment temperature leads to an increasing sintering of the catalyst particles with reduction of the active area, although the catalyst treated at 550 ºC presents more CO tolerance for the HOR.

Direcionamentos da tecnologia industrial de células a combustível de óxidos sólidos

This manuscript shows an overview of the solid oxide fuel cell (SOFC) technology based on industrial developments. The information presented has been collected mostly at conferences that the authors attended. It is observed that several companies have been pursuing the development of the SOFC technology. Significant advances in stability and power density have raised the economic interest in this technology recently. It is revealed that the SOFC materials are essentially the same ones that have been used in the past decades, and that the two most important designs of pre-commercial SOFC prototypes are the tubular and planar ones.

Avaliação da eficiência de uma célula a combustível estacionária de ácido fosfórico

Operation and performance of a commercial PAFC power plant were analyzed. Processes influencing energy conversion efficiency were studied in each module of the fuel cell power plant. The main processes were simulated using mass and energy balance equations, and the results were validated by means of experimental data. It was concluded that the electrical efficiency is higher in comparison with microturbines. The main result achieved is a better understanding of balance of plant processes, knowledge necessary for fuel cell power plant development.

Cério: propriedades catalíticas, aplicações tecnológicas e ambientais

Cerium based-compounds have great importance in a wide range of technological applications, such as: fuel cell devices development; metallurgic processes, petroleum refining; glass and ceramic production. Recently, its catalytic properties have been also explored for environmental applications, especially those to prevent or to control atmospheric and water pollution. Subjects covered in this work include a brief description of the fundaments of cerium catalytic properties and some relevant technological applications. Special attention is given to its photocatalytic activity and its ability to degrade pollutants. Recent results and future prospect about these applications are also evaluated.

Montagem e caracterização elétrica de pilhas a combustível de óxido sólido (PaCOS)

This paper is focused on a review of the design features and the electrochemistry characterization of anode-supported planar SOFC. Studies and results of metallic alloy interconnectors and recovery for protection against corrosion and for contact layer are showed. Moreover a discussion of examples of measurements of impedance spectrometry, according to the literature and our experimental results are made. For the anode supported fuel cells the power density varies from 0.1 to 0.5 Wcm², according to results in the literature (showed in this paper). For electrolyte supported fuel cell the power density can be 10 Wcm-2 for high temperatures. An English-Portuguese glossary of most used terms in SOFC stack is given for greater clarity and to introduce new terms to the reader.

Desenvolvimento e avaliação de um porta-amostra de baixo custo para caracterização elétrica de materiais cerâmicos

Conventional sample holder cells used to the electric characterization of ceramics at high temperature consists of an alumina tube and platinum wires and plates using a complex design. The high cost materials used in the conventional sampler holder cell were replaced by stainless steel and conventional ceramics. The sample holder was validated by characterizing yttria-stabilized-zirconia in a temperature range of 25 to 700 ºC. The results do not present variations, discontinuity or unusual noise in the electric signals. Several samples were characterized without maintenance, which demonstrates that the sample holder is electric and mechanic adequate to be used to electrical characterization of ceramics up to 700 ºC.

Desenvolvimento de conjunto membrana-eletrodos para célula a combustível de metanol direto passiva

Direct methanol fuel cells (DMFCs) without external pumps or other ancillary devices for fuel and oxidant supply are known as passive DMFCs and are potential candidates to replace lithium-ion batteries in powering portable electronic devices. This paper presents the results obtained from a membrane electrode assembly (MEA) specifically designed for passive DMFCs. Appropriated electrocatalysts were prepared and the effect of their loadings was investigated. Two types of gas diffusion layers (GDL) were also tested. The influence of the methanol concentration was analyzed in each case. The best MEA performance presented a maximum power density of 11.94 mW cm-2.

Pilhas de combustíveis microbianas utilizadas na produção de eletricidade a partir de rejeitos orgânicos: uma perspectiva de futuro

In this review is presented an innovative technology for use of animal and vegetable waste with high pollution levels in microbial fuel cell (MFC) as an alternative to waste remediation and simultaneously producing electricity and fertilizer for agriculture. A brief history of MFC, the studies about the electron transfer mechanisms, discussion of the biological nanowires in bacteria and the use of chemical mediators or carriers of electrons are explained. The factors influencing the performance of MFCs, the application in waste and sewage treatment and power generation are also discussed.

Desenvolvimento de processo de produção de conjuntos eletrodo-membrana-eletrodo para células a combustível baseadas no uso de membrana polimérica condutora de prótons (PEMFC) por impressão a tela

Proton exchange membrane fuel cell (PEMFC) requires membrane electrode assemblies (MEA) to generate electrical energy from hydrogen and oxygen. In this study a MEA production process by sieve printing and an ink composition were developed to produce catalyst layers of MEAs. The deposition of the exact catalyst content was possible on cathodes and anodes with only one print step. The optimal ink developed shown viscosity of 2.75 Pa s, density 1.27 g cm-3, total solid content of 33.76 % and tack of 92 U.T. The electrodes prepared in only one printing step showed higher performance than those prepared in several steps.

Desenvolvimento de tecnologia para confecção de eletrodos e conjuntos eletrodo-membrana-eletrodo (MEA) por impressão à tela para aplicação em módulos de potência de células PEMFC

Significant functions in the Proton Exchange Membrane Fuel Cells (PEMFCs) rely on Gas Diffusion Layers (GDLs), such as control the water balance in the membrane electrode assembly (MEA), allow suitable gas permeability and porosity, etc. Aware of the GDL importance in the cell performance and its great demand in scale-up projects, the fuel cell research group at Instituto de Pesquisas Energéticas e Nucleares (IPEN) has developed a Sieve Printing method (innovative in Brazil) as a strategic solution for producing GDL and electrodes used in high power PEMFC stacks. The method has shown to be adequate to fabricate low cost electrodes, GDLs of different dimensions and to produce any amount of MEAs for power stacks.

A utilização de etanol em célula a combustível de óxido sólido

This work reports a review on the status and technical feasibility of the application of ethanol as fuel for Solid Oxide Fuel Cells (SOFC), presenting both external reform and cell with direct utilization of ethanol. Based on this survey, both experimental results and mathematical modeling indicated the technical feasibility of power generation by ethanol SOFC, with cell units producing 450 mW/cm², sufficient for scale up to large stationary plants. The quantitative assessments in the literature show this field to be promising for researchers and private sector investment as well being a strategic technology for government policy in the short and long term.

Tasajännitetason nosto polttokennosovelluksessa

Polttokennojen, erityisesti SOFC-kennojen, tutkimuksessa on viime vuosina saavutettu merkittäviä edistysaskelia ja mahdollisuudet kennojen laajamittaiseen hyödyntämiseen paranevat koko ajan. Polttokennojen yleistyessä tarvitaan tehoelektroniikkaa muokkaamaan kennojen tasajännite verkkoon sopivaksi vaihtojännitteeksi. Verkkovaihtosuuntaaja vaatii korkeamman jännitetason, kuin polttokennosta on saatavissa, joten tasajännitetasoa on ensin nostettava. Tässä diplomityössä esitellään kolme eri hakkuritopologiaa ja perehdytään kokosiltahakkurin optimointiin. Hakkurin pääasialliset häviölähteet olivat toision diodisilta ja transistorit. Diodien vaihtaminen piidiodeista piikarbididiodeihin ei parantanut hyötysuhdetta, koska toision jännite tarkastellussa sovelluksessa oli matala. Muuntajan käämiminen litz-johtimella paransi hyötysuhdetta merkittävästi.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Vertailu kahden erityyppisen virtasyötetyn hakkurin soveltuvuudesta polttokennokäyttöihin

Concerns about condition of the environment and rising fossil fuel prices have accelerated the research of finding new cheap and environmental friendly energy source. Fuel cells are one of the most promising green technologies, especially in the field of distributed energy generation, backup power systems, transportation and mobile power generation. In this bachelor’s thesis use of fuel cells is studied, especially from the DC-DC converter point of view. This bachelor’s thesis concentrates on study of two different DC-DC converters. The aim of this thesis is to study design and steering methods for proposed converters. The ultimate aim of this thesis is to determine which one of proposed converters is most suitable for fuel cell applications.