A New ROV Design: Issues on Low Drag and Mechanical Symmetry

This paper reports the design of a new remotely operated underwater vehicle (ROV), which has been developed at the Underwater Systems and Technology Laboratory (USTL) - University of Porto. This design is contextualized on the KOS project (Kits for underwater operations). The main issues addressed here concern directional drag minimization, symmetry, optimized thruster positioning, stability and layout of ROV components. This design is aimed at optimizing ROV performance for a set of different operational scenarios. This is achieved through modular configurations which are optimized for each different scenario.

Incidence of respiratory viruses in preterm infants submitted to mechanical ventilation

The objectives of this study were to determine the incidence of infection by respiratory viruses in preterm infants submitted to mechanical ventilation, and to evaluate the clinical, laboratory and radiological patterns of viral infections among hospitalized infants in the neonatal intensive care unit (NICU) with any kind of acute respiratory failure. Seventy-eight preterm infants were studied from November 2000 to September 2002. The newborns were classified into two groups: with viral infection (Group I) and without viral infection (Group II). Respiratory viruses were diagnosed in 23 preterm infants (29.5%); the most frequent was respiratory syncytial virus (RSV) (14.1%), followed by influenza A virus (10.2%). Rhinorrhea, wheezing, vomiting and diarrhea, pneumonia, atelectasis, and interstitial infiltrate were significantly more frequent in newborns with nosocomial viral infection. There was a correlation between nosocomial viral infection and low values of C-reactive protein. Two patients with mixed infection from Group I died during the hospital stay. In conclusion, RSV was the most frequent virus in these patients. It was observed that, although the majority of viral lower respiratory tract infections had a favorable course, some patients presented a serious and prolonged clinical manifestation, especially when there was concomitant bacterial or fungal infection.

Gender differences in internet usage habits: a case study in higher education

The usage of information and communication technologies has been growing among students and teachers. In order to improve the use of the Internet as a tool to support teaching and learning it is necessary to understand the Internet usage habits of students. Thus, a study was conducted with 1397 students from five schools of the Polytechnic of Porto. The data was collected through an online questionnaire abd was analized by age range, gender and scientific field. In this paper,gender differences are analyzed and presented in 3 dimensions: type of Internet usage, communication tools and the role of the Internet tools in education.

Differences in internet and LMS usage: a case study in higher education

The Internet plays an important role in higher education institutions where Learning Management Systems (LMS) occupies a main role in the eLearning realm. In this chapter we aim to characterize the Internet and LMS usage patterns and their role in the largest Portuguese Polytechnic Institute. The usage patterns were analyzed in two components: characterization of Internet usage and the role of Internet and LMS in education. Using a quantitative approach, the data analysis describes the differences between gender, age and scientific fields. The carried qualitative analysis allows a better understanding of students’ both motivations, opinions and suggestions of improvement. The outcome of this work is the presentation of the Portuguese students’ profile regarding Internet and LMS usage patterns. We expect that these results can be used to select the most suitable digital pedagogical processes and tools to be adopted regarding the learning process and most adequate LMS’s policies.

An evaluation of manual and mechanical methods to identify Candida spp. from human and animal sources

To compare two yeast identification methods, i. e, the manual and the VITEK mechanical methods, 62 clinical samples from hemocultures and animal sources were analyzed. After identification as Candida yeasts by the VITEK method, the strains were recharacterized using manual assimilation methods and sugar fermentation tests. Our findings reveal 58% concurrent identification between the two methods for animal strains, and 51% for human hemoculture strains.

Probabilistic models for mechanical properties of prestressing strands

This study focus on the probabilistic modelling of mechanical properties of prestressing strands based on data collected from tensile tests carried out in Laboratório Nacional de Engenharia Civil (LNEC), Portugal, for certification purposes, and covers a period of about 9 years of production. The strands studied were produced by six manufacturers from four countries, namely Portugal, Spain, Italy and Thailand. Variability of the most important mechanicalproperties is examined and the results are compared with the recommendations of the ProbabilisticModel Code, as well as the Eurocodes and earlier studies. The obtained results show a very low variability which, of course, benefits structural safety. Based on those results, probabilistic modelsfor the most important mechanical properties of prestressing strands are proposed.

Febrifugine derivative antimalarial activity: quantum mechanical predictors

Plasmodium falciparum resistant strain development has encouraged the search for new antimalarial drugs. Febrifugine is a natural substance with high activity against P. falciparum presenting strong emetic property and liver toxicity, which prevent it from being used as a clinical drug. The search for analogues that could have a better clinical performance is a current topic. We aim to investigate the theoretical electronic structure by means of febrifugine derivative family semi-empirical molecular orbital calculations, seeking the electronic indexes that could help the design of new efficient derivatives. The theoretical results show there is a clustering in well-defined ranges of several electronic indexes of the most selective molecules. The model proposed for achieving high selectivity was tested with success.

The effect of adhesive thickness on the mechanical behavior of a structural polyurethane adhesive

One parameter that influences the adhesively bonded joints performance is the adhesive layer thickness. Hence, its effect has to be investigated experimentally and should be taken into consideration in the design of adhesive joints. Most of the results from literature are for typical structural epoxy adhesives which are generally formulated to perform in thin sections. However, polyurethane adhesives are designed to perform in thicker sections and might have a different behavior as a function of adhesive thickness. In this study, the effect of adhesive thickness on the mechanical behavior of a structural polyurethane adhesive was investigated. The mode I fracture toughness of the adhesive was measured using double-cantilever beam (DCB) tests with various thicknesses of the adhesive layer ranging from 0.2 to 2 mm. In addition, single lap joints (SLJs) were fabricated and tested to assess the influence of adhesive thickness on the lap-shear strength of the adhesive. An increasing fracture toughness with increasing adhesive thickness was found. The lap-shear strength decreases as the adhesive layer gets thicker, but in contrast to joints with brittle adhesives the decrease trend was less pronounced.

Mechanical properties of chemically modified portuguese pinewood

To turn wood into a construction material with enhanced properties, many methods of chemical modification have been developed in the last few decades. In this work, mechanical properties of pine wood were chemically modified, compared and evaluated. Maritime pine wood (Pinus pinaster) was modified with four chemical processes: 1,3-dimethylol-4,5- dihydroxyethyleneurea, N-methylol melamine formaldehyde, tetra-alkoxysilane and wax. The following mechanical properties were assessed experimentally: Modulus of elasticity measured statically, stiffness stabilization efficiency in different climates (30 and 87% of relative humidity), modulus of rupture, work maximum load, impact bending strength, compression, tensile and shear strength at indoor conditions (65% of relative humidity). In both types of active principle of modification, cell wall or lumen fill, no significant changes on the bending stiffness (modulus of elasticity) were found. In the remaining properties analysed significant changes in the modified wood-material took place compared to unmodified wood control: - Cell wall modification was the most effective method to achieve high stiffness stabilization efficiency (up to 60%) and also increased compression strength (up to 230%). However, modulus of rupture, tensile, shear and the impact bending strength were reduced by both resins, but in a varying extent, where the N-methylol melamine formaldehyde endured less reduction than 1,3-dimethylol-4,5-dihydroxyethyleneurea resin. In the latter, reduction up to 60% can take place. - In the lumen fill modification: tetra-alkoxysilane has no effect in the mechanical properties. Although, a slight increase in shear strength parallel to the grain was found. Wax specimens have shown a slight increase in bending strength, compression, tensile and shear strength as well as in the absorption energy capacity.

Correlation between the mechanical cycling behavior and microstructure in laser welded joints using NiTi memory shape alloys

Dissertação para obtenção do Grau de Mestre em Engenharia de Materiais

Estudo da Resistência Mecânica do Betão com Agregado Cerâmico Vermelho

Os sectores da construção e demolição de edifícios são responsáveis por um elevado volume de produção de resíduos. Estes resíduos são normalmente direcionados para aterros, que se encontram, neste momento, sobrelotados. Esta falta de capacidade de receção de resíduos tem como consequência imediata o aumento dos valores monetários associados ao depósito destes materiais excedentários. Com a elevada produção destes resíduos torna-se importante a sua reciclagem e reutilização. No caso da Engenharia Civil, uma grande produtora de resíduos, seria ainda mais interessante o seu reaproveitamento imediato na área. Nesta investigação, pretendeu-se avaliar o desempenho mecânico de betões com diferentes percentagens de agregados cerâmicos vermelhos. Essa investigação passou numa fase inicial pelo estado fresco do betão, de forma a analisar a sua trabalhabilidade. Na fase seguinte, analisou-se no estado endurecido, a resistência à compressão e resistência à tração por compressão diametral. Para concretização deste objetivo produziram-se três tipos de betões: um de referência (areia fina e brita fina), um betão com incorporação de agregados finos e grossos de cerâmica vermelha, juntamente com a areia fina e a brita fina, e o terceiro, um betão com a substituição total da areia fina por cerâmica fina. A realização desta investigação, demostrou que os betões com a incorporação de agregado cerâmico vermelho apresentam resultados de boa qualidade, sendo plausível a sua utilização em estruturas.

Estudo da Delaminação em Compósitos de Epóxido Reforçado com Borracha e Fibras Naturais

Nos últimos anos, a utilização dos materiais compósitos tem vindo a tornar-se cada vez mais comum em várias indústrias, onde se verifica uma ascensão na procura pelos mesmos. Características como o baixo peso aliado à sua alta resistência e rigidez permitem que estes materiais possuam diversas aplicações em variadas áreas, desde a medicina, aeronáutica, indústria automóvel e aeroespacial, até à indústria eletrónica. Hoje em dia, o uso de desperdícios sólidos de borracha e fibras naturais na produção de materiais compósitos é, mais que uma opção, uma necessidade ambiental. De forma a reduzir as enormes quantidades de desperdícios, foi criado um material compósito constituído por uma resina termoendurecível reforçada com esses dois tipos de desperdícios. Parâmetros de fabrico como a percentagem de borracha, o tamanho das partículas de borracha, a percentagem de fibras de cana-de-açúcar e o comprimento dessas fibras foram variados, com o objetivo de estudar a influência destes dois materiais nas propriedades mecânicas do compósito. Apesar da maior parte dos compósitos serem fabricados na forma de uma peça funcional quase pronta a ser utilizada, por vezes é necessário recorrer à maquinação de furos. Apesar das muitas técnicas de furação existentes, os defeitos resultantes deste processo aplicado aos materiais compósitos são ainda muito comuns. Desses defeitos o que mais se destaca é sem dúvida a delaminação. Trinta e seis provetes de epóxido reforçado com borracha e fibra de cana-de-açúcar foram fabricados e furados, de modo a possibilitar o estudo das propriedades mecânicas do material compósito, assim como a análise da zona danificada durante a furação. Diferentes condições de furação, como tipos de broca e velocidades de avanço diferentes, foram impostas aos provetes de forma a variar o mais possível a zona de dano de uns furos para os outros. Parâmetros como a área de dano ou ainda o fator de delaminação provam ser muito úteis na caracterização e quantificação do dano na zona periférica de um furo. Recorrendo a técnicas de processamento de imagem foi possível obter esses parâmetros. O processamento e análise de imagem pode ser feito através de vários métodos. O método utilizado neste trabalho foi o software MATLAB® associado a ferramentas de processamento de imagem. Depois de feita a análise dos furos foram realizados ensaios de esmagamento a todos os provetes. Este passo permitiu assim avaliar de que forma os parâmetros de furação influenciam a resistência mecânica do material, e se a avaliação realizada aos furos é um método viável para a avaliação da extensão de dano nesses furos.

Análise do processo de desenvolvimento de novos produtos na indústria

No âmbito da unidade curricular Dissertação/Projeto do 2º ano do Mestrado em Engenharia mecânica – Ramo Gestão Industrial do Instituto Superior de Engenharia do Porto, o presente trabalho enquadra-se na análise do processo de desenvolvimento de novos produtos na indústria, como suporte à gestão de projetos. No seguimento da necessidade que as empresas têm cada vez mais presente em investirem na melhoria do processo de desenvolvimento de novos produtos, isso conduz a uma garantia de cumprimento de prazos e qualidade, à redução de custos, aumento de vendas, aumento de receitas, satisfação de clientes, entre outros benefícios. O trabalho foi desenvolvido, na empresa Doureca Produtos Plásticos, Lda, no Departamento de Engenharia. À medida que o projeto de melhoria avançou, foi cativante observar como os resultados obtidos contribuíam para a alteração dos paradigmas de trabalho da empresa e o impacto na melhoria continua, em função do caminho traçado da busca da máxima eficiência e eficácia. As ferramentas de melhoria são o suporte ideal, que ajudam a atingir a meta da sustentabilidade dos negócios, mas o maior obstáculo, continua a ser o fator humano. A implementação destes sistemas de melhoria requer uma maior abertura para a utilização das respetivas ferramentas, e uma mobilização dos diferentes intervenientes com vista à obtenção de resultados. Após uma avaliação da situação inicial, foram identificados pontos a melhorar na organização, de seguida foi definida a visão do que deveria ser implementado tendo em conta a estratégia da empresa, e posteriormente executado um plano de implementação das melhorias. No decurso do trabalho foram implementadas novas ferramentas de auxílio para o desenvolvimento de novos produtos como suporte à gestão de projetos. Estas ferramentas são apoiadas na filosofia LEAN, de forma a eliminar desperdícios e criar valor através da melhor utilização dos recursos.

Coreceptor Usage by HIV-1 and HIV-2 Primary Isolates: The Relevance of CCR8 Chemokine Receptor as an Alternative Coreceptor

The human immunodeficiency virus replication cycle begins by sequential interactions between viral envelope glycoproteins with CD4 molecule and a member of the seven-transmembrane, G-protein-coupled, receptors' family (coreceptor). In this report we focused on the contribution of CCR8 as alternative coreceptor for HIV-1 and HIV-2 isolates. We found that this coreceptor was efficiently used not only by HIV-2 but particularly by HIV-1 isolates. We demonstrate that CXCR4 usage, either alone or together with CCR5 and/or CCR8, was more frequently observed in HIV-1 than in HIV-2 isolates. Directly related to this is the finding that the non-usage of CXCR4 is significantly more common in HIV-2 isolates; both features could be associated with the slower disease progression generally observed in HIV-2 infected patients. The ability of some viral isolates to use alternative coreceptors besides CCR5 and CXCR4 could further impact on the efficacy of entry inhibitor therapy and possibly also in HIV pathogenesis.

Multiple Mechanical Complications in ST-Segment Elevation Myocardial Infarction with Angiographically Normal Coronary Arteries

This case report discusses an unusual presentation of ST-segment elevation myocardial infarction (STEMI) with normal coronary arteries and severe mechanical complications successfully treated with surgery. An 82-year-old man presented STEMI with angiographically normal coronary arteries and no major echocardiographic alterations at discharge. At the first month follow-up, he complained of fatigue and dyspnea, and contrast echocardiography complemented by cardiac magnetic resonance imaging revealed a large left ventricular apical aneurysm with a thrombus communicating by two jets of a turbulent flow to an aneurysmatic formation of the right ventricular apex. The patient underwent a Dor procedure, which was successful. Ventricular septal defects and ventricular aneurysms are rare but devastating complications of STEMI, with almost all patients presenting multivessel coronary artery disease. Interestingly in this case, the angiographic pattern was normal.