Synergism between high-pressure processing and active packaging against Listeria monocytogenes in ready-to-eat chicken breast

The effects of high-pressure processing (HPP) in conjunction with an essential oil-based active packaging on the surface of ready-to-eat (RTE) chicken breast were investigated as post-processing listericidal treatment. Three different treatments were used, and all samples were vacuum packed: (i) HPP at 500. MPa for 1. min (control), (ii) active packaging based on coriander essential oil, and (iii) active packaging and HPP. When applied individually, active packaging and pressurisation delayed the growth of Listeria monocytogenes. The combination of HPP and active packaging resulted in a synergistic effect reducing the counts of the pathogen below the detection limit throughout 60. days storage at 4. °C. However, when these samples were stored at 8. °C, growth did occur, but again a delay in growth was observed. The effects on colour and lipid oxidation were also studied during storage and were not significantly affected by the treatments. Active packaging followed by in-package pressure treatment could be a useful approach to reduce the risk of L. monocytogenes in cooked chicken without impairing its quality. Industrial relevance: Ready-to-eat products are of great economic importance to the industry. However, they have been implicated in several outbreaks of listeriosis. Therefore, effective ways to reduce the risk from this pathogenic microorganism can be very attractive for manufacturers. This study showed that the use of active packaging followed by HPP can enhance the listericidal efficiency of the treatment while using lower pressure levels, and thus having limited effects on colour and lipid oxidation of RTE chicken breast.

Virgin Olive Oil: Losses of Antioxidant Polar Phenolic Compounds due to Storage, Packaging, and Culinary Uses

Virgin olive oil is a high quality natural product obtained only by physical means. In addition to triacylglycerols it contains nutritionally important polar and non-polar antioxidant phenols and other bioactive ingredients. The polar fraction is a complex mixture of phenolic acids, simple phenols, derivatives of the glycosides oleuropein and ligstroside, lignans, and flavonoids. These compounds contribute significantly to the stability, flavor, and biological value of virgin olive. In the various stages of production, during storage and in the culinary uses, polar phenols and other valuable bioactive ingredients may be damaged. Oxidation, photo-oxidation, enzymic hydrolysis and heating at frying temperatures have a serious adverse effect. Due to the biological importance of the oil and its unique character, analytical methods have been developed to evaluate antioxidant activity or analyse complex phenol mixtures. These are based on radical scavenging assays and chromatographic techniques. Hyphenated methods are also used including liquid chromatography-mass spectrometry and liquid chromatography-nuclear magnetic resonance spectroscopy.

Hydroprocessing of waste cooking oil over a dispersed nano catalyst: Kinetics study and temperature effect

The kinetics of hydrodeoxygenation of waste cooking oil (WCO) is investigated with unsupported CoMoS catalysts. A kinetic model is established and a comprehensive analysis of each reaction pathway is carried out. The results show that hydrodecarbonylation/decarboxylation (HDC) routes are the predominant reaction pathways in the elimination of oxygen, with the rate constant three times as high as that of hydrodeoxygenation (HDO). However, the HDC activity of the CoMoS catalyst deactivates due to gradual loss of sulfur from the catalyst. HDO process is insensitive to the sulfur deficiency. The kinetic modeling shows that direct hydrodecarbonylation of fatty acids dominates the HDC routes and, in the HDO route, fatty acids are transferred to aldehydes/alcohols and then to C-18 hydrocarbons, a final product, and the reduction of acids is the rate limiting step. The HDO route via alcohols is dominant over aldehydes due to a significantly higher reaction rate constant. The difference of C-18/C-17 ratio in unsupported and supported catalysts show that a support with Lewis acid sites may play an important role in the selectivity for the hydrodeoxygenation pathways and promoting the final product quality

Facile synthesis of nanocrystalline LiFePO4/graphene composite as cathode material for high power lithium ion batteries

We describe a simple strategy, which is based on the idea of space confinement, for the synthesis of carbon coating on LiFePO₄ nanoparticles/graphene nanosheets composites in a water-in-oil emulsion system. The prepared composite displayed high performance as a cathode material for lithium-ion battery, such as high reversible lithium storage capacity (158 mA h g^-1 after 100 cycles), high coulombic efficiency (over 97%), excellent cycling stability and high rate capability (as high as 83 mA h g ^-1 at 60 C). Very significantly, the preparation method employed can be easily adapted and be extended as a general approach to sophisticated compositions and structures for the preparation of highly dispersed nanosized structure on graphene. 

Synthesis of new vegetable oil-based polymeric materials

A crescente procura de recursos fosseis a que se tem assistido nos ultimos anos, tem resultado num crescimento sem precedentes dos precos, com consequencias imprevisiveis e que levara, no espaco de decadas, ao seu inevitavel esgotamento. A procura de um modelo de desenvolvimento sustentavel, baseado em recursos renovaveis e o grande desafio que se coloca a civilizacao no seculo XXI. A biomassa vegetal, atraves das designadas gBio-refinarias h, e uma alternativa logica para a producao de produtos quimicos e de materiais mas tambem de combustiveis e energia. Os oleos vegetais constituem uma das fracoes da biomassa vegetal, cuja exploracao tem merecido redobrada atencao nos ultimos anos, como fonte de materiais e de combustiveis. Assim, a presente dissertacao tem por objetivo o desenvolvimento de novos materiais polimericos derivados de oleos vegetais, seguindo duas abordagens distintas, nomeadamente a preparacao de polimeros atraves de polimerizacao por etapas e polimerizacao em cadeia (Parte B e C, respetivamente). Em primeiro lugar, foram sintetizados poliesteres alifaticos de cadeia longa a partir de monomeros provenientes do oleo de colza (Capitulo III). A auto-metatese do acido erucico com catalisadores de rutenio, seguida de hidrogenacao da ligacao dupla, originou o acido 1,26-hexacosanodioico, que por sua vez foi convertido em hexacosano-1,26-diol. Subsequentemente, a policondensacao do acido ƒ¿,ƒÖ-dicarboxilico de cadeia longa com o hexacosano-1,26-diol originou o poliester 26,26. O diacido C26 foi tambem polimerizado com outros alcano-diois de cadeia curta, nomeadamente o dodecano-1,12-diol e o butano-1,2-diol, produzindo, respetivamente, os poliesteres 12,26 e 4,26. Estes poliesteres de fontes 100% renovaveis possuem valores de Mn na ordem dos 8-14 kDa e valores de PDI entre 2.1 e 2.7. As propriedades destes poliesteres alifaticos foram avaliadas atraves de varias tecnicas, revelando elevada cristalinidade (com uma estrutura cristalina como a do polietileno) e elevadas temperaturas de fusao (74-104 ‹C), cristalizacao (68-92 ‹C) e degradacao (323-386 ‹C). Em segundo lugar, foram sintetizados polimeros lineares termo-reversiveis a partir de derivados do oleo de ricinio (Capitulo IV). Para tal foram preparados monomeros que incorporam aneis furanicos inseridos atraves do acoplamento tiol-eno, e que posteriormente foram polimerizados pela reacao de Diels-Alder (DA) entre os grupos furano (dieno A) e estruturas complementares do tipo maleimida (dienofilo B). Para as polimerizacoes DA foram consideradas duas abordagens diferentes, nomeadamente (i) o uso de monomeros com dois aneis furanicos terminais em conjunto com uma bismaleimida (sistemas AA+BB) e (ii) a utilizacao de um monomero que incorpora ambos os grupos reativos, furano e maleimida, na sua estrutura (sistema AB). Este estudo demonstrou claramente que ambas as estratégias foram bem sucedidas embora com diferentes resultados em termos da natureza dos produtos obtidos. Estes polímeros lineares apresentam valores relativamente baixos de Tg (-40 to -2 °C) devido à natureza flexível dos grupos separadores das funções reativas, e de Mn (4.5-9.0 kDa) dada a observada tendência de ciclização associada a concentrações baixas de monómero. A aplicação da reação de retro-DA aos polímeros em causa confirmou o seu caráter reversível, ou seja, a possibilidade de promover, em condições controladas, a despolimerização com recuperação dos monómeros de partida. Esta particularidade abre caminhos para materiais macromoleculares originais com aplicações promissoras tais como auto-reparação e reciclabilidade. Em terceiro lugar, sintetizaram-se polímeros não-lineares termo-reversíveis a partir de derivados do óleo de ricínio (Capítulo V). Para tal foram preparados monómeros trifuncionais e posteriormente polimerizados através da reação de DA entre os grupos reativos complementares furano/maleimida. Foram consideradas três abordagens distintas para preparar estes polímeros não-lineares, nomeadamente através da utilização de (i) um monómero bisfurânico em combinação com uma trismaleimida (sistema A2+B3) e (ii) um monómero trisfurânico em conjunto com uma bismaleimida (sistema A3+B2) que originaram materiais ramificados ou reticulados, e ainda (iii) a utilização de monómeros assimetricamente substituídos do tipo A2B ou AB2 capazes de originar estruturas macromoleculares hiper-ramificadas. Todos os sistemas apresentaram valores de Tg perto de 0 °C, o que era de esperar para estes materiais não-lineares. A aplicação da reação de retro-DA comprovou mais uma vez o caráter termo-reversível das polimerizações em causa. Em quarto lugar e último lugar, foram preparados copolímeros de acetato de vinilo (VAc) com monómeros derivados de óleo de girassol (Capítulo VI). Ésteres vinílicos de ácidos gordos (FAVE) foram sintetizados por transvinilação dos ácidos oleico e linoleico com VAc catalisada por um complexo de irídio. Os monómeros vinílicos preparados foram caracterizados e posteriormente homopolimerizados e copolimerizados com VAc através do uso dos grupos vinílicos terminais como função inicial de polimerização. A variação do tipo e quantidade de monómero FAVE e da quantidade de iniciador radicalar originou copolímeros de VAc com valores de Mn na gama de 1.2-3.0 kDa e valores de Tg de -5 a 16 °C. Os copolímeros foram avaliados em testes de cura oxidativa através das insaturações nas suas cadeias alifáticas para formar materiais reticulados, e os resultados sugerem que eles podem ser sistemas efetivos de cura para aplicações como tintas, vernizes e outros tipos de revestimento. Todos os materiais poliméricos preparados ao longo deste trabalho constituem contribuições atrativas para a área dos polímeros oriundos de recursos renováveis e representam uma prova indiscutível de que os óleos vegetais são percursores promissores de materiais macromoleculares com potenciais aplicações.

Natural substances and high pressure processing to preserve sea bass

Esta tese teve como objectivo estudar estratégias de conservação de pescado fresco, recorrendo ao uso de extractos e óleos essenciais de plantas e do processamento por alta pressão (HPP), usando filetes de robalo como um caso de estudo modelo. Relativamente aos extractos e óleos essenciais, avaliaram-se as suas propriedades antibacterianas e antioxidantes. Os extractos aquosos quente de poejo e de orégão e o óleo essencial de cravinho apresentaram a maior actividade antioxidante. Os óleos essenciais foram mais eficientes do que os extractos para inibir o crescimento das estirpes bacterianas testadas, tendo-se observado os menores valores de concentração mínima inibitória nos óleos essenciais de orégão, citronela, alho e orégão Espanhol. De seguida, estudou-se o efeito dos óleos essenciais de orégão Espanhol e de limão na conservação de filetes de robalo fresco tendo em conta critérios microbiológicos, químicos, físicos e sensoriais. A aplicação do óleo essencial de orégão Espanhol aumentou o tempo de vida útil dos filetes sob o ponto de vista bacteriano, mas não em termos sensoriais. A combinação dos óleos essenciais de orégão Espanhol e de limão melhorou o efeito antioxidante e reduziu a intensidade do odor e a sua eficácia em relação às Enterobacteriaceae, comparando com o tratamento com óleo essencial de orégão Espanhol per se. No sentido de reduzir o odor conferido pelos óleos essenciais realizou-se um estudo de conservação para avaliar o efeito de películas com óleos essenciais (citronela, alho e tomilho) em filetes de robalo, recorrendo a uma teste de desafio bacteriano. As películas sem óleos essenciais aumentaram o tempo de vida útil sob o ponto de vista bacteriano, mas este efeito não foi observado com a incorporação dos óleos essenciais nas películas. Em relação ao HPP, testaram-se diversas condições (nível de pressão, tempo de pressurização e taxa de pressurização) e avaliaram-se os efeitos na actividade enzimática, na qualidade global e na conservação de filetes de robalo fresco. Em geral, o aumento do nível de pressão e do tempo de pressurização diminuiu a actividade da fosfatase ácida e das enzimas proteolíticas, a carga bacteriana e a capacidade de retenção de água, enquanto que os filetes ficaram mais brancos. O HPP revelou potencial para o desenvolvimento de novos produtos: mais brancos, não translúcidos, mais firmes e com maior tempo de frescura e estabilidade microbiológica. Em conclusão, os óleos essenciais e o HPP têm potencial para conservar pescado fresco, devido aos seus efeitos na qualidade bacteriana. Ainda assim, mais esforços devem ser feitos no sentido de reduzir a transferência de odor dos óleos essenciais para o pescado e os efeitos do HPP no aspecto do pescado e na oxidação lipídica.

High temperature vapour-liquid equilibria of water-polyalcohol mixtures

Tese de doutoramento, Química (Química Tecnológica), Universidade de Lisboa, Faculdade de Ciências, 2014

Determination of the most suitable oil pipeline route using GIS least cost path analysis

The Keystone XL has a big role for transforming Canadian oil to the USA. The function of the pipeline is decreasing the dependency of the American oil industry on other countries and it will help to limit external debt. The proposed pipeline seeks the most suitable route which cannot damage agricultural and natural water recourses such as the Ogallala Aquifer. Using the Geographic Information System (GIS) techniques, the suggested path in this study got extremely high correct results that will help in the future to use the least cost analysis for similar studies. The route analysis contains different weighted overlay surfaces, each, was influenced by various criteria (slope, geology, population and land use). The resulted least cost path routes for each weighted overlay surface were compared with the original proposed pipeline and each displayed surface was more effective than the proposed Keystone XL pipeline.

ANALYSIS, MODIFICATION, AND EVALUATION OF THE COLD FLOW PROPERTIES OF VEGETABLE OILS AS BASE OIL FOR INDUSTRIAL LUBRICANTS

Poor cold flow properties of vegetable oils are a major problem preventing the usage of many abundantly available vegetable oils as base stocks for industrial lubricants. The major objective of this research is to improve the cold flow properties of vegetable oils by various techniques like additive addition and different chemical modification processes. Conventional procedure for determining pour point is ASTM D97 method. ASTM D97 method is time consuming and reproducibility of pour point temperatures is poor between laboratories. Differential Scanning Calorimetry (DSC) is a fast, accurate and reproducible method to analyze the thermal activities during cooling/heating of oil. In this work coconut oil has been chosen as representative vegetable oil for the analysis and improvement cold flow properties since it is abundantly available in the tropics and has a very high pour point of 24 °C. DSC is used for the analysis of unmodified and modified vegetable oil. The modified oils (with acceptable pour points) were then subjected to different tests for the valuation of important lubricant properties such as viscometric, tribological (friction and wear properties), oxidative and corrosion properties.A commercial polymethacrylate based PPD was added in different percentages and the pour points were determined in each case. Styrenated phenol(SP) was added in different concentration to coconut oil and each solution was subjected to ASTM D97 test and analysis by DSC. Refined coconut oil and other oils like castor oil, sunflower oil and keranja oil were mixed in different proportions and interesterification procedure was carried out. Interesterification of coconut oil with other vegetable oils was not found to be effective in lowering the pour point of coconut oil as the reduction attained was only to the extent of 2 to 3 °C.Chemical modification by acid catalysed condensation reaction with coconut oil castor oil mixture resulted in significant reduction of pour point (from 24 ºC to -3 ºC). Instead of using triacylglycerols, when their fatty acid derivatives (lauric acid- the major fatty acid content of coconut oil and oleic acid- the major fatty acid constituents of monoand poly- unsaturated vegetable oils like olive oil, sunflower oil etc.) were used for the synthesis , the pour point could be brought down to -42 ºC. FTIR and NMR spectroscopy confirmed the ester structure of the product which is fundamental to the biodegradability of vegetable oils. The tribological performance of the synthesised product with a suitable AW/EP additive was comparable to the commercial SAE20W30 oil. The viscometric properties (viscosity and viscosity index) were also (with out additives) comparable to commercial lubricants. The TGA experiment confirmed the better oxidative performance of the product compared to vegetable oils. The sample passed corrosion test as per ASTM D130 method.

Energy saving innovations, non-exhaustible sources of energy and long-run: what would happen if we run out of oil?

We formulate and solve a model of factor saving technological improvement considering three factors of production: labor, capital and energy. The productive activities have three main characteristics: first, in order to use capital goods firms need energy; second, there are two sources of energy: non-exhaustible and exhaustible; third, capital goods can be of different qualities and the quality of these goods can be changed along two dimensions -reducing the need of energy or changing the source of energy used in the production process. The economy goes through three stages of development after industrialization. In the first, firms make use of exhaustible energy and the e¢ ciency in the use of energy is constant. In the second stage, as the price of energy grows the e¢ ciency in its use is increased. In the third stage, the price of exhaustible sources is so high that firms have incentives to use non-exhaustible sources of energy. During this stage the price of energy is constant. In this set up, the end of the oil age has level effects on consumption and output but it does not cause the collapse of the economic system.

A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

Effects of forage source and soybean and marine algal oil supplementation on milk fatty acid composition in ewes

The objective of the present studies was to determine effects of basal dietary forage source on the response of milk fatty acid composition to an oil supplement based (2:1, respectively, w/w) on soybean oil and marine algae biomass oil high in cis-9, cis-12 C18:2n − 3 and C22:6n − 3, respectively. In Study 1, Hampshire × Dorset ewes (48) were randomly assigned to one of four treatments and 12 pens in a completely randomized design blocked on the basis of lambing date and number of lambs suckled. Control rations (60:40 forage:concentrate, dry matter (DM) basis) based on alfalfa pellets (AP) or corn silage (CS) were fed from lambing. Beginning at 22 days postpartum, three pens of ewes fed AP and three pens of ewes fed CS were supplemented with oil (30 g/kg of ration DM) in place of corn meal. Average ewe DM intake (DMI) and average daily gain (ADG) were measured weekly. Milk yield and composition were measured at 42 days postpartum. DMI was lower (P<0.02) for CS and for oil, but milk yield was not affected by forage source or oil supplementation. Milk fat content was higher for oil (P<0.10) and milk protein content was higher for AP (P<0.04). Total CLA concentration (g/100 g fatty acids) increased (P<0.01) with CS and oil, and the response to oil was greater for AP (P<0.04). Similarly, total trans-C18:1 and C22:6ω−3 concentrations were higher for CS and oil, but the response to oil was greater for CS (P<0.06 and P<0.01, respectively). In Study 2, the experiment was repeated using alfalfa haylage (AH) instead of AP. The DMI decreased (P<0.05) with oil feeding, but was not affected by forage source. Milk yield was decreased by feeding oil with AH, but not by feeding oil with CS (P<0.03). Milk fat content tended to be increased by feeding oil with AH, but tended to be decreased by feeding oil with CS (P<0.08). Total CLA concentration was increased (P<0.01) for AH versus CS and by oil, and the response to oil supplementation was greater for AH (P<0.01). In contrast, total trans-C18:1 concentration was higher for CS versus AH, with a greater response to oil for CS (P<0.05). Feeding marine oil increased the C22:6ω−3 (P<0.01) concentration, and the response was greater for AH (P<0.04). To further characterize the response of milk fat composition to dietary oil in ewes, a third study used six pens of three ewes each assigned to either the control CS diet used for Study 2 or the same diet supplemented with 45 g/kg (DM basis) of the oil mixture. Feeding oil had no effect on DMI, milk yield or milk fat concentration, but again increased (P<0.001) total trans-C18:1 and C22:6ω−3 concentrations and numerically increased (114%) total CLA concentration. Milk fatty acid composition responses to supplemental vegetable and marine oils were affected by forage source. Milk trans-C18:1 concentration was higher when CS was fed in Studies 1 and 2, but the effect of forage species on CLA concentration differed between studies, which may reflect differences in diet PUFA content and consumption, as well as amounts of dietary starch and fiber consumed. Despite large increases in trans-C18:1 concentration, milk fat content was not decreased by feeding unsaturated oils to ewes, even at diet levels of 45 g/kg of ration DM.

Examination of the persistency of milk fatty acid composition responses to fish oil and sunflower oil in the diet of dairy cows

Based on the potential benefits of cis-9, trans-11 conjugated linoleic acid (CLA) for human health, there is a need to develop effective strategies for enhancing milk fat CLA concentrations. Levels of cis-9, trans-11 CLA in milk can be increased by supplements of fish oil (FO) and sunflower oil (SO), but there is considerable variation in the response. Part of this variance may reflect time-dependent ruminal adaptations to high levels of lipid in the diet, which lead to alterations in the formation of specific biohydrogenation intermediates. To test this hypothesis, 16 late lactation Holstein-British Friesian cows were used in a repeated measures randomized block design to examine milk fatty acid composition responses to FO and SO in the diet over a 28-d period. Cows were allocated at random to corn silage-based rations (8 per treatment) containing 0 (control) or 45 g of oil supplement/ kg of dry matter consisting (1:2; wt/wt) of FO and SO (FSO), and milk composition was determined on alternate days from d 1. Compared with the control, the FSO diet decreased mean dry matter intake (21.1 vs. 17.9 kg/d), milk fat (47.7 vs. 32.6 g/kg), and protein content (36.1 vs. 33.3 g/kg), but had no effect on milk yield (27.1 vs. 26.4 kg/d). Reductions in milk fat content relative to the FSO diet were associated with increases in milk trans-10 18: 1, trans-10, cis-12 CLA, and trans-9, cis-11 CLA concentrations (r(2) = 0.74, 0.57, and 0.80, respectively). Compared with the control, the FSO diet reduced milk 4: 0 to 18: 0 and cis 18:1 content and increased trans 18:1, trans 18:2, cis-9, trans-11 CLA, 20: 5 n-3, and 22: 6 n-3 concentrations. The FSO diet caused a rapid elevation in milk cis-9, trans-11 CLA content, reaching a maximum of 5.37 g/100 g of fatty acids on d 5, but these increases were transient, declining to 2.35 g/100 g of fatty acids by d 15. They remained relatively constant thereafter. Even though concentrations of trans-11 18: 1 followed the same pattern of temporal changes as cis-9, trans-11 CLA, the total trans 18:1 content of FSO milk was unchanged because of the concomitant increases in the concentration of other isomers (Delta(4-10) and Delta(12-15)), predominantely trans-10 18:1. In conclusion, supplementing diets with FSO enhances milk fat cis-9, trans-11 CLA content, but the high level of enrichment declines because of changes in ruminal biohydrogenation that result in trans-10 replacing trans-11 as the major 18:1 biohydrogenation intermediate formed in the rumen.