The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Innovations of ageing and societal transition : Dynamics of change of the socio-technical regime of ageing

The purpose of this dissertation is to examine the dynamics of the socio-technical system in the field of ageing. The study stems from the notion that the ageing of the population as a powerful megatrend has wide societal effects, and is not just a matter for the social and health sector. The central topic in the study is change: not only the age structures and structures of society are changing, but also at the same time there is constant development, for instance, in technologies, infrastructures and cultural perceptions. The changing concept of innovation has widened the understanding of innovations related to ageing from medical and assistive technological innovations to service and social innovations, as well as systemic innovations at different levels, which means the intertwined and co-evolutionary change in technologies, structures, services and thinking models. By the same token, the perceptions of older people and old age are becoming more multi-faceted: old age is no longer equated to illnesses and decline, but visions of active ageing and a third age have emerged, which are framed by choices, opportunities, resources and consumption in later life. The research task in this study is to open up the processes and mechanisms of change in the field of ageing, which are studied as a complex, multi-level and interrelated socio-technical system. The question is about co-effective elements consisting of macro-level landscape changes, the existing socio-technical regime (the rule system, practices and structures) and bottom-up niche-innovations. Societal transitions do not account for the things inside the regime alone, or for the long-term changes in the landscape, nor for the radical innovations, but for the interplay between all these levels. The research problem is studied through five research articles, which offer micro-level case studies to macro-level phenomenon. Each of the articles focus on different aspects related to ageing and change, and utilise various datasets. The framework of this study leans on the studies of socio-technical systems and multi-level perspective on transitions mainly developed by Frank Geels. Essential factors in transition from one socio-technological regime to another are the co-evolutionary processes between landscape changes, regime level and experimental niches. Landscape level changes, like the ageing of the population, destabilise the regime in the forms of coming pressures. This destabilization offers windows for opportunity to niche-innovations outside or at fringe of the regime, which, through their breakthrough, accelerate the transition process. However, the change is not easy because of various kinds of lock-ins and inertia, which tend to maintain the stability of the regime. In this dissertation, a constructionist approach of society is applied leaning mainly to the ideas of Anthony Giddens’ theory of structuration, with the dual nature of structures. The change is taking place in the interplay between actors and structures: structures shape people’s practices, but at the same time these practices constitute and reproduce social systems. Technology and other material aspects, as part of socio-technical systems, and the use of them, also take part in the structuration process. The findings of the study point out that co-evolutionary and co-effective relationships between economic, cultural, technological and institutional fields, as well as relationships between landscape changes, changes in the local and regime-level practices and rule systems, are a very complex and multi-level dynamic socio-technical phenomenon. At the landscape level of ageing, which creates the pressures and triggers to the regime change, there are three remarkable megatrends: demographic change, changes in the global economy and the development of technologies. These exert pressures to the socio-technical regime, which as a rule system is experiencing changes in the form of new markets and consumer habits, new ways of perceiving ageing, new models of organising the health care and other services and as new ways of considering innovation and innovativeness. There are also inner dynamics in the relationships between these aspects within the regime. These are interrelated and coconstructed: the prevailing perceptions of ageing and innovation, for instance, reflect the ageing policies, innovation policies, societal structures, organising models, technology and scientific discussion, and vice versa. Technology is part of the inner dynamics of the sociotechnological regime. Physical properties of the artefacts set limitations and opportunities with regard to their functions and uses. The use of and discussion about technology, contributes producing and reproducing the perceptions of old age. For societal transition, micro-level changes are also needed, in form of niche-innovations, for instance new services, organisational models or new technologies, Regimes, as stabilitystriven systems, tend to generate incremental innovations, but radically new innovations are generated in experimental niches protected from ‘normal’ market selection. The windows of opportunity for radical novelties may be opened if the circumstances are favourable for instance by tensions in the socio-technical regime affected by landscape level changes. This dissertation indicates that a change is taking place, firstly, in the dynamic interactionbetween levels, as a result of purposive action and governance to some extent. Breaking the inertia and using the window of opportunity for change and innovation offered by dynamics between levels, presupposes the actors’ special capabilities and actions such as dynamic capabilities and distance management. Secondly, the change is taking place the socio-technological negotiations inside the regime: interaction between technological and social, which is embodied in the use of technology. The use of technology includes small-level contextual scripts that also participate in forming broader societal scripts (for instance defining old age at the society level), which in their turn affect the formation of policies for innovation and ageing. Thirdly, the change is taking place by the means of active formation of the multi-actor innovation networks, where the role of distance management is crucial to facilitate the communication between actors coming from different backgrounds as well as to help the niches born outside the regime to utilise the window of opportunity offered by regime destabilisation. This dissertation has both theoretical and practical contributions. This study participates in the discussion of action-oriented view on transition by opening up of the socio-technological, coevolutionary processes of the multi-faceted phenomenon of ageing, which has lacked systematic analyses. The focus of this study, however, is not on the large-scale coordination and governance, but rather on opening up the incremental elements and structuration processes, which contribute to the transition little by little, and which can be affected to. This increases the practical importance of this dissertation, by highlighting the importance of very tiny, everyday elements in the change processes in the long run.

Computer tools applied to analysis of solar water heaters

The simulation programs are important tools to analyze the different energetic alternatives, including the use of renewable energy. The objective of this study was to analyze comparatively the different computer tools available for modeling of solar water heaters. Among the main simulation software of solar thermal systems, there are: RETScreen International, EnergyPlus, TRNSYS, SolDesigner, SolarPro, e T*SOL. Among the tools mentioned, only EnergyPlus and RETScreen International are free, but they allow obtaining interesting results when applied together. The first one has a detailed module of energy analysis of solar water heaters, while the second one provides an detailed economic feasibility study and an assessment of emissions of greenhouse gases. RETScreen International and EnergyPlus programs are aimed at a diverse audience, including designers, researchers and energy planners.

The accumulation of financial and social capital as a means to achieve a sustained competitive advantage for consumer co-operatives

By so far, scholars have discussed how the characteristics of consumer co-operatives (cooperative principles, values and the dual role of members as the users and owners) can potentially give them a competitive advantage over investor-owned firms (IOFs). In addition, concern for the community (as partly derived from locality and regionality) has been seen as a potential source of success for consumer co-operatives. On the other hand, the geographicbound purpose of consumer co-operation causes that consumer co-operative can be regarded as a challenging company form to manage. This is because, according to the purpose of consumer co-operation, co-operatives are obligated to 1) provide the owners with services and goods that are needed and do so at more affordable prices than their competitors do and/or 2) to operate in areas in which competitors do not want to operate (for example, because of the low profitability in certain area of business or region). Thus, consumer co-operatives have to operate very efficiently in order to execute this geographic-bound corporate purpose (e.g. they cannot withdraw from the competition during the declining stages of business). However, this efficiency cannot be achieved by any means; as the acceptance from the important regional stakeholders is the basic operational precondition and lifeline in the long run. Thereby, the central question for the survival and success of consumer co-operatives is; how should the consumer co-operatives execute its corporate purpose so it can be the best alternative to its members in the long run? This question has remained unanswered and lack empirical evidence in the previous studies on the strategic management of consumer cooperation. In more detail, scholars have not yet empirically investigated the question: How can consumer co-operatives use financial and social capital to achieve a sustained competitive advantage? It is this research gap that this doctoral dissertation aims to fulfil. This doctoral dissertation aims to answer the above questions by combining and utilizing interview data from S Group co-operatives and the central organizations in S Group´s network (overall, 33 interviews were gathered), archival material and 56 published media articles/reports. The study is based on a qualitative case study approach that is aimed at theory development, not theory verification (as the theory is considered as nascent in this field of study). Firstly, the findings of this study indicate that consumer co-operatives accumulate financial capital; 1) by making profit (to invest and grow) and 2) by utilizing a network-based organizational structure (local supply chain economies). As a result of financial capital accumulation, consumer co-operatives are able to achieve efficiency gains but also remain local. In addition, a strong financial capital base increases consumer co-operatives´ independence, competitiveness and their ability to participate in regional development (which is in accordance with their geographically bound corporate purpose). Secondly, consumer cooperatives accumulate social capital through informal networking (with important regional stakeholders), corporate social responsibility (CSR) behaviour and CSR reporting, pursuing common good, and interacting and identity sharing. As a result of social capital accumulation, consumer co-operatives are able to obtain the resources for managing; 1) institutional dependencies and 2) customer relations. By accumulating both social and financial capital through the above presented actions, consumer co-operatives are able to achieve sustained competitive advantage. Finally, this thesis provides useful ideas and new knowledge for cooperative managers concerning why and how consumer co-operatives should accumulate financial and social capital (to achieve sustained competitive advantage), while aligning with their corporate purpose.

The effects of maternal hyperglycemia on human umbilical vascular gene expression and neonatal rat lung development

Background: Maternal diabetes affects many fetal organ systems, including the vasculature and the lungs. The offspring of diabetic mothers have respiratory adaptation problems after birth. The mechanisms are multifactorial and the effects are prolonged during the postnatal period. An increasing incidence of diabetic pregnancies accentuates the importance of identifying the pathological mechanisms, which cause the metabolic and genetic changes that occur in offspring, born to diabetic mothers. Aims and methods: The aim of this thesis was to determine changes both in human umbilical cord exposed to maternal type 1 diabetes and in neonatal rat lungs after streptozotocin-induced maternal hyperglycemia, during pregnancy. Rat lungs were used as a model for the potential disease mechanisms. Gene expression alterations were determined in human umbilical cords at birth and in rat pup lungs at two week of age. During the first two postnatal weeks, rat lung development was studied morphologically and histologically. Further, the effect of postnatal hyperoxia on hyperglycemia-primed rat lungs was investigated at one week of age to mimic the clinical situation of supplemental oxygen treatment. Results: In the umbilical cord, maternal diabetes had a major negative effect on the expression of genes involved in blood vessel development. The genes regulating vascular tone were also affected. In neonatal rat lungs, intrauterine hyperglycemia had a prolonged effect on gene expression during late alveolarization. The most affected pathway was the upregulation of extracellular matrix proteins. Newborn rat lungs exposed to intrauterine hyperglycemia had thinner saccular walls without changes in airspace size, a smaller relative lung weight and lung total tissue area, and increased cellular apoptosis and proliferation compared to control lungs, possibly reflecting an aberrant maturational adaptation. At one and two weeks of age, cell proliferation and secondary crest formation were accelerated in hyperglycemia-exposed lungs. Postnatal hyperoxic exposure, alone caused arrested alveolarization with thin-walled and enlarged alveoli. In contrast, the dual exposure of intrauterine hyperglycemia and postnatal hyperoxia resulted in the phenotype of thick septa together with arrested alveolarization and decreased number of small pulmonary arteries. Conclusions: Maternal diabetic environment seems to alter the umbilical cord gene expression profile of the regulation of vascular development and function. Fetal hyperglycemia may additionally affect the genetic regulation of the postnatal lung development and may actually induce prolonged structural alterations in neonatal lungs together with a modifying effect on the deleterious pulmonary exposure of postnatal hyperoxia. This, combined with the novel human umbilical cord gene data could serve as stepping stones for future therapies to curb developmental aberrations.

Value engineering of InnoTrackTM

Middle section module of InnoTrackTM moving walk was re-engineered according to value analysis process. Self-supporting steel structure for moving walk was created as a result of this process. Designed structure was verified and validated by prototype tests and finite element method calculations. Self-supporting steel structure replaces the original design of middle section module in InnoTrackTM. Designed structure provides higher satisfaction to customers’ needs and at the same time, it uses less resources. The redesigned middle section module provides higher value to the customer.

Modelling of ultrasound assisted mixing in Newtonian and non-Newtonian liquids

The purpose of this work is to obtain a better understanding of behaviour of possible ultrasound appliance on fluid media mixing. The research is done in the regard to Newtonian and non-Newtonian fluids. The process of ultrasound appliance on liquids is modelled in COMSOL Multiphysics software. The influence of ultrasound using is introduced as waveform equation. Turbulence modelling is fulfilled by the k-ε model in Newtonian fluid. The modeling of ultrasound assisted mixing in non-Newtonian fluids is based on the power law. To verify modelling results two practical methods are used: Particle Image Velocimetry and measurements of mixing time. Particle Image Velocimetry allows capturing of velocity flow field continuously and presents detailed depiction of liquid dynamics. The second way of verification is the comparison of mixing time of homogeneity. Experimentally achievement of mixing time is done by conductivity measurements. In modelling part mixing time is achieved by special module of COMSOL Multiphysics – the transport of diluted species. Both practical and modelling parts show similar radial mechanism of fluid flow under ultrasound appliance – from the horn tip fluid moves to the bottom and along the walls goes back. Velocity profiles are similar in modelling and experimental part in the case of Newtonian fluid. In the case of non-Newtonian fluid velocity profiles do not agree. The development track of ultrasound-assisted mixing modelling is presented in the thesis.

Regulation of the kinin receptors after induction of myocardial infarction: a mini-review

It is well known that the responses to vasoactive kinin peptides are mediated through the activation of two receptors termed bradykinin receptor B1 (B1R) and B2 (B2R). The physiologically prominent B2R subtype has certainly been the subject of more intensive efforts in structure-function studies and physiological investigations. However, the B1R activated by a class of kinin metabolites has emerged as an important subject of investigation within the study of the kallikrein-kinin system (KKS). Its inducible character under stress and tissue injury is therefore a field of major interest. Although the KKS has been associated with cardiovascular regulation since its discovery at the beginning of the last century, less is known about the B1R and B2R regulation in cardiovascular diseases like hypertension, myocardial infarction (MI) and their complications. This mini-review will summarize our findings on B1R and B2R regulation after induction of MI using a rat model. We will develop the hypothesis that differences in the expression of these receptors may be associated with a dual pathway of the KKS in the complex mechanisms of myocardial remodeling.

Main food sources of carotenoids, according to the purpose and degree of processing, for beneficiaries of the 'Bolsa Família' in Brazil

The intake of carotenoids is associated with antioxidant properties and some of these substances have activity of pro-vitamin A. This study aimed to estimate the intake of carotenoids (average values) by the Brazilian population focusing on beneficiaries of the 'Bolsa Família' Program and identify the dietary sources, according to the purpose and degree of processing and the inclusion of food additives. The database used is the personal food consumption module of the Household Budget Survey of 2008-2009, conducted by the Brazilian Institute of Geography and Statistics. The content of carotenoids in foods was obtained primarily from a National data source. Food products were classified into three categories: 1) fresh and minimally processed foods; 2) processed foods (containing food additives, except for flavoring and coloring agents); and 3) highly processed foods (containing flavoring and coloring agents). Insufficient intakes were identified for the conditional cash transfer program beneficiaries (3,547.1 µg). Fresh and minimally processed foods supplied between 48.6% (for girls) and 65.7% (for male adults) of pro-vitamin carotenoids. Processed foods were sources of between 55.5% and 57.0% of lutein + zeaxanthin for elderly and between 58.0% and 67.8% of lycopene for adults. Highly processed foods contributed to less than 5.0% of total carotenoids.

Performance improvement in mediterranean operations using risk management analysis : Case study of Containerships Group Ltd

Emerging markets of Northern Africa and Turkey provide growth opportunities for logistics service companies in the middle of low growth environment of European Union. The purpose of this research is to explore and analyze the risk factors in container shipping industry and third party logistics (3PL) services. The research empirically examined the risk factors, which are related within the interaction between these two parties in emerging markets of Mediterranean area. The previous studies have provided a valuable insight into the operational risks faced by container shipping industries. However, most of these studies have focused on one or several operational risk factors from a single point of view, and no studies have inclusively examined the possible operational risks faced in the container shipping industry from dual perspective of 3PL provider and its customers. A questionnaire has been deployed to collect related data; and the impacts of the risks were then be assessed and ranked using the method of risk mapping. Respondents were located in Turkey, Algeria, Tunisia, and Libya. Research presents the most important risk factors identified, and compares them between 3PL provider and its customers. The research also provide some risk mitigation strategies for the key risk factors, and tried to figure out a common risk picture, which guides the managers in both sides to have a better decisions and as a result, improve the performance of the container shipping operations. Challenge during project execution time was that customers identified vast amount of more risks than what was the case with logistics service operator.

Problem solving and computer-assisted instruction in science education : analysis of research findings and the research process /

The quantitative component of this study examined the effect of computerassisted instruction (CAI) on science problem-solving performance, as well as the significance of logical reasoning ability to this relationship. I had the dual role of researcher and teacher, as I conducted the study with 84 grade seven students to whom I simultaneously taught science on a rotary-basis. A two-treatment research design using this sample of convenience allowed for a comparison between the problem-solving performance of a CAI treatment group (n = 46) versus a laboratory-based control group (n = 38). Science problem-solving performance was measured by a pretest and posttest that I developed for this study. The validity of these tests was addressed through critical discussions with faculty members, colleagues, as well as through feedback gained in a pilot study. High reliability was revealed between the pretest and the posttest; in this way, students who tended to score high on the pretest also tended to score high on the posttest. Interrater reliability was found to be high for 30 randomly-selected test responses which were scored independently by two raters (i.e., myself and my faculty advisor). Results indicated that the form of computer-assisted instruction (CAI) used in this study did not significantly improve students' problem-solving performance. Logical reasoning ability was measured by an abbreviated version of the Group Assessment of Lx)gical Thinking (GALT). Logical reasoning ability was found to be correlated to problem-solving performance in that, students with high logical reasoning ability tended to do better on the problem-solving tests and vice versa. However, no significant difference was observed in problem-solving improvement, in the laboratory-based instruction group versus the CAI group, for students varying in level of logical reasoning ability.Insignificant trends were noted in results obtained from students of high logical reasoning ability, but require further study. It was acknowledged that conclusions drawn from the quantitative component of this study were limited, as further modifications of the tests were recommended, as well as the use of a larger sample size. The purpose of the qualitative component of the study was to provide a detailed description ofmy thesis research process as a Brock University Master of Education student. My research journal notes served as the data base for open coding analysis. This analysis revealed six main themes which best described my research experience: research interests, practical considerations, research design, research analysis, development of the problem-solving tests, and scoring scheme development. These important areas ofmy thesis research experience were recounted in the form of a personal narrative. It was noted that the research process was a form of problem solving in itself, as I made use of several problem-solving strategies to achieve desired thesis outcomes.

Marginal/minority popular music : the concept of the "third space" and the case for "hybridities" of cultures/identities /

The topic of this thesis is marginaVminority popular music and the question of identity; the term "marginaVminority" specifically refers to members of racial and cultural minorities who are socially and politically marginalized. The thesis argument is that popular music produced by members of cultural and racial minorities establishes cultural identity and resists racist discourse. Three marginaVminority popular music artists and their songs have been chosen for analysis in support of the argument: Gil Scott-Heron's "Gun," Tracy Chapman's "Fast Car" and Robbie Robertson's "Sacrifice." The thesis will draw from two fields of study; popular music and postcolonialism. Within the area of popular music, Theodor Adorno's "Standardization" theory is the focus. Within the area of postcolonialism, this thesis concentrates on two specific topics; 1) Stuart Hall's and Homi Bhabha's overlapping perspectives that identity is a process of cultural signification, and 2) Homi Bhabha's concept of the "Third Space." For Bhabha (1995a), the Third Space defines cultures in the moment of their use, at the moment of their exchange. The idea of identities arising out of cultural struggle suggests that identity is a process as opposed to a fixed center, an enclosed totality. Cultures arise from historical memory and memory has no center. Historical memory is de-centered and thus cultures are also de-centered, they are not enclosed totalities. This is what Bhabha means by "hybridity" of culture - that cultures are not unitary totalities, they are ways of knowing and speaking about a reality that is in constant flux. In this regard, the language of "Otherness" depends on suppressing or marginalizing the productive capacity of culture in the act of enunciation. The Third Space represents a strategy of enunciation that disrupts, interrupts and dislocates the dominant discursive construction of US and THEM, (a construction explained by Hall's concept of binary oppositions, detailed in Chapter 2). Bhabha uses the term "enunciation" as a linguistic metaphor for how cultural differences are articulated through discourse and thus how differences are discursively produced. Like Hall, Bhabha views culture as a process of understanding and of signification because Bhabha sees traditional cultures' struggle against colonizing cultures as transforming them. Adorno's theory of Standardization will be understood as a theoretical position of Western authority. The thesis will argue that Adorno's theory rests on the assumption that there is an "essence" to music, an essence that Adorno rationalizes as structure/form. The thesis will demonstrate that constructing music as possessing an essence is connected to ideology and power and in this regard, Adorno's Standardization theory is a discourse of White Western power. It will be argued that "essentialism" is at the root of Western "rationalization" of music, and that the definition of what constitutes music is an extension of Western racist "discourses" of the Other. The methodological framework of the thesis entails a) applying semiotics to each of the three songs examined and b) also applying Bhabha's model of the Third Space to each of the songs. In this thesis, semiotics specifically refers to Stuart Hall's retheorized semiotics, which recognizes the dual function of semiotics in the analysis of marginal racial/cultural identities, i.e., simultaneously represent embedded racial/cultural stereotypes, and the marginal raciaVcultural first person voice that disavows and thus reinscribes stereotyped identities. (Here, and throughout this thesis, "first person voice" is used not to denote the voice of the songwriter, but rather the collective voice of a marginal racial/cultural group). This dual function fits with Hall's and Bhabha's idea that cultural identity emerges out of cultural antagonism, cultural struggle. Bhabha's Third Space is also applied to each of the songs to show that cultural "struggle" between colonizers and colonized produces cultural hybridities, musically expressed as fusions of styles/sounds. The purpose of combining semiotics and postcolonialism in the three songs to be analyzed is to show that marginal popular music, produced by members of cultural and racial minorities, establishes cultural identity and resists racist discourse by overwriting identities of racial/cultural stereotypes with identities shaped by the first person voice enunciated in the Third Space, to produce identities of cultural hybridities. Semiotic codes of embedded "Black" and "Indian" stereotypes in each song's musical and lyrical text will be read and shown to be overwritten by the semiotic codes of the first person voice, which are decoded with the aid of postcolonial concepts such as "ambivalence," "hybridity" and "enunciation."

The Effectiveness of Learning Portfolios: A Study of Quality Assurance Programs of Selected Health Regulatory Colleges in Ontario

Health regulatory colleges promote quality practice and continued competence through Quality Assurance (QA) programs. For many colleges, a QA program includes the use of portfolios that incorporate self-directed learning. The purpose of this study was to determine some of the issues surrounding the effectiveness of QA portfolio programs. The literature review revealed that portfolios are valuable tools, but gaps in knowledge include a comparative analysis of QA programs and the perspective of regulatory college administrators. Data were collected through interviews with 6 administrators and a review of 14 portfolio models described on college websites. The results from the two data sources were applied to Robert Stake's responsive evaluation framework to identify issues related to the portfolio's effectiveness (Stake, 1967). The learning components of portfolios were analyzed through the humanist and constructivist lenses. All 14 portfolio models were found to have 3 main components: self-diagnosis, learning plan and activities, and self-evaluation. However, differences were uncovered in learners' autonomy in selecting learning activities, methods of portfolio evaluation, and the relationship between the portfolio and other QA components. The results revealed a dual philosophy of learning in portfolio models and an apparent contradiction between the needs of the individual learner and the organization. Paths for future research include the tenuous relationship between competence and learning, and the impact of technical approaches on selfdirected learning initiatives. A key recommendation is to acknowledge the unique identity of each profession so that health regulatory colleges can address legislative demands and learner needs.

Synthesis and Characterisation of Thermoplastic Ionomers based on Natural Rubber

Chemically modified novel thermo-reversible zinc sulphonated ionomers based on natural rubber (NR), radiation induced styrene grafted natural rubber (RI-SGNR), and chemically induced styrene grafted natural rubber (CI-SGNR) were synthesized using acetyl sulphate/zinc acetate reagent system. Evidence for the attachment of sulphonate groups has been furnished by FTIR spectra. which was supplanted by FTNMR results. Estimation of the zinc sulphonate group was done using spectroscopic techniques such as XRFS and ICPAES. The TGA results prove improvement in the therrno-oxidative stability of the modified natural rubber. Both DSC and DMTA studies show that the incorporation of the ionic groups affect the thermal transition of the base polymer. Retention of the improved physical properties of the novel ionomers even after three repeated cycles of mastication and molding at 120 degree C may be considered as the evidence for the reprocessabiJity of the ionomer. Effect of both particulate (carbon black. silica & zinc stearate) and fibrous fillers (nylon & glass) on the properties of the radiation induced styrene grafted natural rubber ionomer has been evaluated. Incorporation of HAF carbon black results in maximum improvement in physical properties. Silica reinforces the backbone chain and weakens the ionic associations. Zinc stearate plays the dual role of reinforcement and ptasticization. The nylon and glass filled lonorner compounds show good improvement in the physical properties in comparison with the neat ionomer. Dispersion and adhesion of the fillers in the ionomer matrix has been amply supported by their SEM micrographs. Microwave probing of the electrical behavior of the 26.5 ZnSRISGNR ionomer reveals that the maximum relative complex conductivity and the complex permittivity appear at the frequency of 2.6 GHz. The complex conductivity of the base polymer increases from 1.8x 10.12 S/cm to 3.3xlO·4 S/cm. Influence of fillers on the dielectric constant and conductivity of the new ionic thermoplastic elastomer has been studied. The ionomer I nylon compound shows the highest microwave conductivity. Use of the 26.5 ZnS-RISGNR ionomer as a compatibilizer for obtaining the technologically compatible blends from the immiscible SBR/NBR system has been verified. The heat fugitive ionic cross-linked natural rubber may be, therefore, useful as an alternative to vulcanized rubber and thermoplastic elastomer

Studies on some Metal Complexes of Dithio Ligands

The thesis deals with our studies on the synthesis and elucidation of structure of some metal complexes of dithio ligands, such as the dithiocarbamates, xanthates and 2-aminocyclopent-1-ene-1-dithiocarboxylate and its N-alkyl derivatives.2-Aminocyclopent-1-ene-1-dithiocarboxylate (ACDA) is an interesting ligand, because of its potential dual capability of bonding between the metal and the ligand. Since the earlier reports on the complexes of ACDA contain contradictory ideas on the nature of its bonding, it was thought worthwhile to undertake a detailed and systematic study of these type of complexes. As the ACDA complexes have very low solubilities in solvents like chloroform, we have used the isopropyl derivative of ACDA as the ligand. The increased solubility of these complexes have made it possible to investigate their NMR and solution electronic spectra.The complexes of this ligand have not yet been reported in the literature.We have synthesised some new mixed ligand complexes of dithiocarbamates by reacting bis(dithiocarbamato)-µ-dichloro dicopper complexes (obtained by the reaction of mixed benzoic dithiocarbamic anhydride and copper(II) chloride) with ACDA or its N-alkyl derivatives.Interactions of metal halides with the mixed anhydrides formed from benzoylchloride and xanthates have also been investigated. Novel complexes of the type, [Cu2(RXant)CI] (R=i-Bu, i-Pr, n-Bu or n-Pr)) have been isolated from the reaction of copper(II) chloride and the mixed anhydride, and these reactions appear to be like the clock reactions reported in the literature.It also deal with the characterisation of the complexes of the type [Hg(R2d t c )X] (X=Cl, Br or 1),[Cu3(R2dtc)6][Cu2Br6] and [Cu(R2dtc)Cl2](R2=Me2,Et2,Pip,Morph or Pyrr)respectively, synthesised by simple and novel routes, different from those reported earlier.