Synthesis, structural and ferromagnetic properties of La1-xKxMnO3 (0.0 <= x <= 0.25) phases by solution combustion method

We describe the solution combustion synthesis and characterization of La1-xKxMnO3 (0.0 <= x <= 0.25) perovskite phases, which is a low temperature initiated, rapid route to prepare metal oxides. As-synthesized compounds are amorphous in nature; crystallinity was observed on heating at 800 degrees C for 5 min. Structural parameters were determined by the Rietveld refinement method using powder XRD data. Parent LaMnO3 compound crystallizes in the orthorhombic structure (space group Pbnm, No. 62). Potassium substituted compounds were crystallized with rhombohedral symmetry (space group R-3c, No. 167). The ratio of the Mn3+/Mn4+ was determined by the iodometric titration. The Fourier transform infrared spectrum (FTIR) shows two absorption bands for Mn-O stretching vibration (v, mode), Mn-O-Mn deformation vibration (v(b) mode) around 600 cm(-1) and 400 cm(-1) for the compositions, x = 0.0, 0.05 and 0-10. Four-probe electrical resistivity measurements reveal a composition controlled metal to insulator transition (TM-1), the maximum TM-1 was observed for the composition La0.85K0.15MnO3 at 287 K. Room temperature vibrating sample magnetometer data indicate that for the composition up to x = 0-10, the compounds are paramagnetic whereas composition with x = 0.15, 0.20 and 0.25 show magnetic moments of 27, 29 and 30 emu/g, respectively.

Elastic modulus of Ti-6Al-4V-xB alloys with B up to 0.55 wt.%

An anomalous variation in the experimental elastic modulus, E, of Ti-6Al-4V-xB (with x up to 0.55 wt.%) is reported. Volume fractions and moduli of the constituent phases were measured using microscopy and nanoindentation,respectively. These were used in simple micromechanical models to examine if the E values could be rationalized. Experimental E values higher than the upper bound estimates suggest complex interplay between microstructural modifications, induced by the addition of B, and properties.

VIBRANTe 2.0

ARTIST STATEMENT VIBRANTe 2.0 was inspired by a research project for Parkinson’s disease patients aimed at developing a wearable device to collect relevant data for patients and medical health professionals. Vibrante is a Spanish word that translates to vibrant; literally meaning shaking or vibrations. Vibrante also has a dual meaning including vibrancy, energy, activity, and liveliness. Parkinson’s can be a debilitating disease, but it does not mean the person has to lose energy, activeness or vibrancy. As technology moves from being worn to becoming implantable and completely hidden within the body, the very notion of its physicality becomes difficult to grasp. While the human body hides implantable technology, VIBRANTe 2.0 intentionally hides the human body by making it invisible to reveal the technology stitched within. Wires become veins, delivering lifeblood to the technology inside, allowing it to pulsate and exist, while motherboards become networked hubs by which information is transferred through and within the body, performing functions that mirror and often surpass human performance capabilities. Ultimately, VIBRANTe 2.0 seeks to prompt the viewer to reflect on the potential ramifications of the complete immersion of technology into the human body. CONTEXT Technology is increasingly penetrating all aspects of our environment, and the rapid uptake of devices that live near, on or in our bodies is facilitating radical new ways of working, relating and socialising. Such technology, with its capacity to generate previously unimaginable levels of data, offers the potential to provide life-augmenting levels of interactivity. However, the absorption of technology into the very fabric of clothes, accessories and even bodies begins to dilute boundaries between physical, technological and social spheres, generating genuine ethical and privacy concerns and potentially having implications for human evolution. Embedding technology into the fabric of our clothes, accessories, and even the body enable the acquisition of and the connection to vast amounts of data about people and environments in order to provide life-augmenting levels of interactivity. Wearable sensors for example, offer the potential for significant benefits in the future management of our wellbeing. Fitness trackers such as ‘Fitbit’ and ‘Garmen’ provide wearers with the ability to monitor their personal fitness indicators while other wearables provide healthcare professionals with information that improves diagnosis and observation of medical conditions. This exhibition aimed to illustrate this shifting landscape through a selection of experimental wearable and interactive works by local, national and international artists and designers. The exhibition will also provide a platform for broader debate around wearable technology, our mediated future-selves and human interactions in this future landscape. EXHIBITION As part of Artisan’s Wearnext exhibition, the work was on public display from 25 July to 7 November 2015 and received the following media coverage: [Please refer to Additional URLs]

A 100MHz to 1GHz, 0.35V to 1.5V supply 256 x 64 SRAM mock using symmetrized 9T SRAM cell with controlled read

In this paper, we present Dynamic Voltage and Frequency Managed 256 x 64 SRAM block in 65nm technology, for frequency ranging from 100MHz to 1GHz. The total energy is minimized for any operating frequency in the above range and leakage energy is minimized during standby mode. Since noise margin of SRAM cell deteriorates at low voltages, we propose Static Noise Margin improvement circuitry, which symmetrizes the SRAM cell by controlling the body bias of pull down NMOS transistor. We used a 9T SRAM cell that isolates Read and Hold Noise Margin and has less leakage. We have implemented an efficient technique of pushing address decoder into zigzag-super-cut-off in stand-by mode without affecting its performance in active mode of operation. The Read Bit Line (RBL) voltage drop is controlled and pre-charge of bit lines is done only when needed for reducing power wastage.

Sinteractivity, proton conductivity and chemical stability of BaZr 0.7In0.3O3-δ for solid oxide fuel cells (SOFCs)

In3+ was used as dopant for BaZrO3 proton conductor and 30 at%-doped BaZrO3 samples (BaZr0.7In 0.3O3-δ, BZI) were prepared as electrolyte materials for proton-conducting solid oxide fuel cells (SOFCs). The BZI material showed a much improved sinteractivity compared with the conventional Y-doped BaZrO 3. The BZI pellets reached almost full density after sintering at 1600 °C for 10 h, whereas the Y-doped BaZrO3 samples still remained porous under the same sintering conditions. The conductivity measurements indicated that BZI pellets showed smaller bulk but improved grain boundary proton conductivity, when compared with Y-doped BaZrO3 samples. A total proton conductivity of 1.7 × 10-3 S cm -1 was obtained for the BZI sample at 700 °C in wet 10% H 2 atmosphere. The BZI electrolyte material also showed adequate chemical stability against CO2 and H2O, which is promising for application in fuel cells.

Grain boundary sliding during diffusion and dislocation creep in a Mg-0.7 pct Al alloy

Early studies on grain boundary sliding (GBS) in Mg alloys have suggested frequently that the contribution of GBS to creep is high even under conditions corresponding to dislocation creep. The role of creep strain and grain size in influencing the experimental measurements has not been clearly identified. Grain boundary sliding measurements were conducted in detail over experimental conditions corresponding to diffusion creep as well as dislocation creep in a single-phase Mg-0.7 wt pet Al alloy. The results indicated clearly that the GBS contribution to creep was Very high during,, diffusion creep at low stresses (similar to 75 pct) and substantially reduced during dislocation creep at high stresses (similar to 15 pct). These measurements were consistent with the observation of significant intragranular slip band activity observed in most grains at high stresses and very little slip band activity at low stresses. The experimental measurements and analysis indicated also that the GBS contribution to creep was high during the initial stages of creep and decreased to a steady-state value at large strains.

Low-frequency resistance fluctuations in metal films under current stressing at low temperature (T<0.3Tmelting)

In this paper, we report a systematic study of low frequency 1∕fα resistance fluctuation in thin metal films (Ag on Si) at different stages of damage process when the film is subjected to high current stressing. The resistance fluctuation (noise) measurement was carried out in situ using a small ac bias that has been mixed with the dc stressing current. The experiment has been carried out as a function of temperature in the range of 150–350 K. The experiment establishes that the current stressed film, as it undergoes damage due to various migration forces, develops an additional low-frequency noise spectral power that does not have the usual 1∕f spectral shape. The magnitude of extra term has an activated temperature dependence (activation energy of ≈0.1 eV) and has a 1∕f1.5 spectral dependence. The activation energy is the same as seen from the temperature dependence of the lifetime of the film. The extra 1∕f1.5 spectral power changes the spectral shape of the noise power as the damage process progress. The extra term likely arising from diffusion starts in the early stage of the migration process during current stressing and is noticeable much before any change can be detected in simultaneous resistance measurements. The experiment carried out over a large temperature range establish a strong correlation between the evolution of the migration process in a current stressed film and the low-frequency noise component that is not a 1∕f noise.

Hydration and distortion of peptide helices in crystals. α-Helical structure of a dodecapeptide, Boc-(Ala-Leu-Aib)4-OMe

The dodecapeptide Boc-(Ala-Leu-Aib)(4)-OMe crystallized with two independent helical molecules in a triclinic cell. The two molecules are very similar in conformation, with a 3(10)-helix turn at the N-terminus followed by an alpha-helix, except for an elongated N(7)...O(3) distance in both molecules. All the helices in the crystal pack in a parallel motif. Eleven water sites have been found in the head-to-tail region between the apolar helices that participate in peptide-water hydrogen bonds and a network of water-water hydrogen bonds. The crystal parameters are as follows: 2(C58H104N12O15)+ca. 10H(2)O, space group P1 with a = 12.946(2), b = 17.321(3), c = 20.465(4) Angstrom, alpha = 103.12(2), beta = 105.63(2), gamma = 107.50(2)degrees, Z = 2, R = 10.9% for 5152 data observed > 3 sigma(F), resolution 1.0 Angstrom. In contrast to the shorter sequences [Karle et al. (1988)Proc. Natl. Acad. Sci. USA 85, 299-303] and Boc-(Ala-Leu-Aib)(2)-OMe [Karle et al. (1989) Biopolymers 28, 773-781], no insertion of a water molecule into the helix is observed. However, the elongated N---O distance between Ala(7) NH and Aib(3) CO in both molecules (molecule A, 3.40 Angstrom; molecule B, 3.42 Angstrom) is indicative of an incipient break in the helices. (C) Munksgaard 1994.

Techno Teacher Moms: Web 2.0 Connecting Mothers in the Home Education Community

Home education is on the rise in Australia. However, unlike parents who choose mainstream schooling, these parents often lack the support of a wider community to help them on their educational and parenting journey. This support is especially lacking as many people in the wider community find the choice to home education confronting. As such, these parents may feel isolated and alienated in the general population as their choice to home educate is questioned at best, and ridiculed at worst. These parents often find sanctuary online in homeschool groups on Facebook. This chapter explores the ways that Facebook Groups are used by marginalized and disenfranchised families who home educate to meet with others who are likeminded and aligned with their beliefs and philosophies. It is through these groups that parents, in relation to schooling it is especially mothers, are able to ask for advice, to vent, to explore options and find connections that may be lacking in the wider community.

Studies in sesquiterpenes—XXVI : Synthesis of 2,2,6-trimethyl-3-oxo-1-carbomethoxybicyclo[0,3,3]octane, a degradation product of patchouli alcohol

The synthesis of the title compound is described and results of some experiments on the degradation of patchouli alcohol are reported.

Search for the rare decays B+→μ+μ-K+, B0→μ+μ-K*(892)0, and Bs0→μ+μ-ϕ at CDF

We search for b to s\mu^+\mu^- transitions in B meson (B^+, B^0, or B^0_s) decays with 924pb^{-1} of p pbar collisions at sqrt(s)=1.96 TeV collected with the CDF II detector at the Fermilab Tevatron. We find excesses with significances of 4.5, 2.9, and 2.4 standard deviations in the B^+ to \mu^+\mu^-K^+, B^0 to \mu^+\mu^-K^*(892)^0, and B_s^0 to \mu^+\mu^-\phi decay modes, respectively. Using B to J/psi h (h = K^+, K^*(892)^0, phi) decays as normalization channels, we report branching fractions for the previously observed B^+ and B^0 decays, BR(B^+ to \mu^+\mu^-K^+)=(0.59\pm0.15\pm0.04) x 10^{-6}, and BR(B^0 to \mu^+\mu^-K^*(892)^0)=(0.81\pm0.30\pm0.10) x 10^{-6}, where the first uncertainty is statistical, and the second is systematic. These measurements are consistent with the world average results, and are competitive with the best available measurements. We set an upper limit on the relative branching fraction BR(B_s^0 to \mu^+\mu^-\phi)/BR(B_s^0 to J/\psi\phi)

Search for the rare decays B+→μ+μ-K+, B0→μ+μ-K*(892)0, and Bs0→μ+μ-ϕ at CDF

We search for b→sμ+μ- transitions in B meson (B+, B0, or Bs0) decays with 924  pb-1 of pp̅ collisions at √s=1.96  TeV collected with the CDF II detector at the Fermilab Tevatron. We find excesses with significances of 4.5, 2.9, and 2.4 standard deviations in the B+→μ+μ-K+, B0→μ+μ-K*(892)0, and Bs0→μ+μ-ϕ decay modes, respectively. Using B→J/ψh (h=K+, K*(892)0, ϕ) decays as normalization channels, we report branching fractions for the previously observed B+ and B0 decays, B(B+→μ+μ-K+)=(0.59±0.15±0.04)×10-6, and B(B0→μ+μ-K*(892)0)=(0.81±0.30±0.10)×10-6, where the first uncertainty is statistical, and the second is systematic. We set an upper limit on the relative branching fraction B(Bs0→μ+μ-ϕ)/B(Bs0→J/ψϕ)<2.6(2.3)×10-3 at the 95(90)% confidence level, which is the most stringent to date.