Lamb mode diversity imaging for non-destructive testing of plate-like structures

Several Lamb wave modes can be coupled to a particular structure, depending on its geometry and transducer used to generate the guided waves. Each Lamb mode interacts in a particular form with different types of defects, like notches, delamination, surface defects, resulting in different information which can be used to improve damage detection and characterization. An image compounding technique that uses the information obtained from different propagation modes of Lamb waves for non-destructive testing of plate-like structures is proposed. A linear array consisting of 16 piezoelectric elements is attached to a 1 mm thickness aluminum plate, coupling the fundamental A0 and S0 modes at the frequencies of 100 kHz and 360 kHz, respectively. For each mode two images are obtained from amplitude and phase information: one image using the Total Focusing Method (TFM) and one phase image obtained from the Sign Coherence Factor (SCF). Each TFM image is multiplied by the SCF image of the respective mode to improve contrast and reduce side and grating lobes effects. The high dispersive characteristic of the A0 mode is compensated for adequate defect detection. The information in the SCF images is used to select one of the TFM mode images, at each pixel, to obtain the compounded image. As a result, dead zone is reduced, resolution and contrast are improved, enhancing damage detection when compared to the use of only one mode. © 2013 Elsevier Ltd.

Wavespeed measurement in buried water distribution pipes and its significance in leak location

To determine the location of leaks in buried water pipes, acoustic methods are often used. These have proven to be very effective in metallic pipes but have been problematic in modern plastic pipes. In this paper the reason why this is so is discussed together with some measurements that were made on a bespoke test rig built by South Staffs Water plc. A particular problem is the estimate of the wavespeed. Tables are frequently used for this purpose, but these are often inaccurate and this means that a leak cannot be located accurately. An in-situ measure of the wavespeed is thus preferable. In this paper it is shown that there are significant issues in obtaining an accurate estimate of the wavespeed when a leak is present in the system. A method is proposed that overcomes some of these problems, which is discussed and is demonstrated using some data from the bespoke test-rig. © (2013) Trans Tech Publications.

Uma Contribuição aos Sistemas de Monitoramento de Integridade Estrutural Baseados na Impedância Eletromecânica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

ZTD em tempo quase real via Estações GNSS Terrestres: estratégia de processamento para o GIPSY-OASIS II e combinação das séries temporais

Pós-graduação em Ciências Cartográficas - FCT

Proliferating cell nuclear antigen immunoreaction in adrenal-tumors

Aims mid background: We studied, retrospectively, 33 cases of adrenal tumors of children at the Pediatric Endocrinology Unit, Children's Institute, Sao Paulo State University Medical School, from 1975 to 1993. Ail patients had at least 2 years of follow-up with a few exceptions. Methods: Clinical follow-up data were correlated with histopathologic review, laboratory data and cell kinetic evaluation (based on detection of proliferating cell nuclear antigens). Results: With one exception, all the patients had presented signs of androgen production and had high levels of dehydro-epiandrosterone-sulfate. Tumor weight evaluation represented a good parameter of neoplasm evolution: of 19 cases weighing less than 250 g, 17 had no evidence of disease after surgery, and 2 had an unfavorable prognosis. Of 14 cases weighing more than 250 g, only 1 had no evidence of disease and 13 had an unfavorable evolution. Conclusions: Proliferating cell nuclear antigen (PCNA) was not helpful to evaluate adrenal neoplasm evolution: our study did not show any correlation between PCNA score and prognosis.

Avaliação dos efeitos dos inseticidas malation e fipronil sobre a viabilidade e regeneração de girardia tigrina (Platyhelminthe, tricladida)

In this study were carried out toxicity tests and the evaluation of sub lethal effects of the insecticides malathion and fipronil, over the test system of Girardia tigrina, using for these analyses a great variety of methods. For evaluation of the lethal concentrations of the products, adult planarians were exposed to several different concentrations. All the tests were carried out in duplicate, maintained on the shelter of the light, on a temperature 24-26ºC and they had the duration of 96h, with observations at each 24h. The results were statically valued by the tests U of Mann- Whitney, Spearman-Karber, ANOVA and Pearson correlation. The effects over the system-test, in the different tested concentrations, varied in accordance with the time of exposition. The EC50 given by the test of Spearman-Karber was of 12,5mg/L for malathion and 13,4mg/L for fipronil. The evaluation of sub lethal effects was composed by analyses of the potential of regeneration; histological, for tissue damage evaluation; d; and the “comet assay”, for DNA damage detection. The specimens split up and exposed to the insecticides demonstrated, between other effects, retardation in development of the regenerative blastema. The histological evaluation has shown that exposed planarians to lower concentrations of the insecticides cause more significant damage against the tissues and some specific cell types. Through the comet assay, significant damages were noticed in the DNA in all the treatments, when compared with the control group. Such damages may result in reproduction and immunity alterations, which reduce the competitive efficiency and, consequently, the survival chances of these organisms.

Detecção de danos em estruturas guiadas usando ondas de alta frequência

Pós-graduação em Engenharia Mecânica - FEIS

Detecção de microrganismos de infecções bucais: perspectivas e cuidados a serem seguidos

The diagnosis of head and neck infections constitutes relevant step in their treatment. However, in spite of the fact that most of diseases in head and neck region are infectious in nature, several reasons collaborated for dentists do not ask laboratory tests in order to help clinical diagnosis. By mean of this review literature, based on research articles about the newest and most reliable methods of diagnosis for clinical laboratories, the authors discuss the advantages and disadvantages of each selected method and the relevant aspects in transportation of the specimens to the laboratory. Saliva, biofilm, pus, and blood are the most frequent specimens for microbial diagnosis, being that the most used methods are culture and those based on detection of deoxyribonucleic acid by polymerase chain reaction method. Whereas, the culture depends on cellular viability, and has reduced sensitivity, as well as needs favorable conditions in the sample collection and transportation, PCR shows high sensitivity and specificity, but it does not allow the determination of antibiogram, what reduces its usefulness. In addition, few laboratories possess conditions to perform cultivation of obligate anaerobes or have experience in the molecular detection of these microorganisms.

Lamb mode diversity imaging fornon-destructivetesting of plate-likestructures

Several Lamb wave modes can be coupled to a particular structure, depending on its geometry and transducer used to generate the guided waves. Each Lamb mode interacts in a particular form with different types of defects, like notches, delamination, surface defects, resulting in different information which can be used to improve damage detection and characterization. An image compounding technique that uses the information obtained from different propagation modes of Lamb waves for non-destructive testing of plate-like structures is proposed. A linear array consisting of 16 piezoelectric elements is attached to a 1 mm thickness aluminum plate, coupling the fundamental A0 and SO modes at the frequencies of 100 kHz and 360 kHz, respectively. For each mode two images are obtained from amplitude and phase information: one image using the Total Focusing Method (TFM) and one phase image obtained from the Sign Coherence Factor (SCF). Each TFM image is multiplied by the SCF image of the respective mode to improve contrast and reduce side and grating lobes effects. The high dispersive characteristic of the A0 mode is compensated for adequate defect detection. The information in the SCF images is used to select one of the TFM mode images, at each pixel, to obtain the compounded image. As a result, dead zone is reduced, resolution and contrast are improved, enhancing damage detection when compared to the use of only one mode. (C) 2013 Elsevier Ltd. All rights reserved. (AU)

Useful computer vision techniques for human-robot interaction

[ES]This paper describes some simple but useful computer vision techniques for human-robot interaction. First, an omnidirectional camera setting is described that can detect people in the surroundings of the robot, giving their angular positions and a rough estimate of the distance. The device can be easily built with inexpensive components. Second, we comment on a color-based face detection technique that can alleviate skin-color false positives. Third, a simple head nod and shake detector is described, suitable for detecting affirmative/negative, approval/dissaproval, understanding/disbelief head gestures.

Systematic studies of protein immobilization by surface plasmon field-enhanced fluorescence spectroscopy

The research interest of this study is to investigate surface immobilization strategies for proteins and other biomolecules by the surface plasmon field-enhanced fluorescence spectroscopy (SPFS) technique. The recrystallization features of the S-layer proteins and the possibility of combining the S-layer lattice arrays with other functional molecules make this protein a prime candidate for supramolecular architectures. The recrystallization behavior on gold or on the secondary cell wall polymer (SCWP) was recorded by SPR. The optical thicknesses and surface densities for different protein layers were calculated. In DNA hybridization tests performed in order to discriminate different mismatches, recombinant S-layer-streptavidin fusion protein matrices showed their potential for new microarrays. Moreover, SCWPs coated gold chips, covered with a controlled and oriented assembly of S-layer fusion proteins, represent an even more sensitive fluorescence testing platform. Additionally, S-layer fusion proteins as the matrix for LHCII immobilization strongly demonstrate superiority over routine approaches, proving the possibility of utilizing them as a new strategy for biomolecular coupling. In the study of the SPFS hCG immunoassay, the biophysical and immunological characteristics of this glycoprotein hormone were presented first. After the investigation of the effect of the biotin thiol dilution on the coupling efficiently, the interfacial binding model including the appropriate binary SAM structure and the versatile streptavidin-biotin interaction was chosen as the basic supramolecular architecture for the fabrication of a SPFS-based immunoassay. Next, the affinity characteristics between different antibodies and hCG were measured via an equilibrium binding analysis, which is the first example for the titration of such a high affinity interaction by SPFS. The results agree very well with the constants derived from the literature. Finally, a sandwich assay and a competitive assay were selected as templates for SPFS-based hCG detection, and an excellent LOD of 0.15 mIU/ml was attained via the “one step” sandwich method. Such high sensitivity not only fulfills clinical requirements, but is also better than most other biosensors. Fully understanding how LHCII complexes transfer the sunlight energy directionally and efficiently to the reaction center is potentially useful for constructing biomimetic devices as solar cells. After the introduction of the structural and the spectroscopic features of LHCII, different surface immobilization strategies of LHCII were summarized next. Among them the strategy based on the His-tag and the immobilized metal (ion) affinity chromatography (IMAC) technique were of great interest and resulted in different kinds of home-fabricated His-tag chelating chips. Their substantial protein coupling capacity, maintenance of high biological activity and a remarkably repeatable binding ability on the same chip after regeneration was demonstrated. Moreover, different parameters related to the stability of surface coupled reconstituted complexes, including sucrose, detergent, lipid, oligomerization, temperature and circulation rate, were evaluated in order to standardize the most effective immobilization conditions. In addition, partial lipid bilayers obtained from LHCII contained proteo-liposomes fusion on the surface were observed by the QCM technique. Finally, the inter-complex energy transfer between neighboring LHCIIs on a gold protected silver surface by excitation with a blue laser (λ = 473nm) was recorded for the first time, and the factors influencing the energy transfer efficiency were evaluated.

Grating coupled surface plasmon enhanced fluorescence spectroscopy

Over the last three decades, sensors based on the phenomenon of surface plasmon resonance have proven particularly suitable for real time thin film characterization, gas detection, biomolecular interaction examination and to supplement electrochemical methods. Systems based on prism coupling have been combined with fluorescence detection under the name of surface plasmon fluorescence spectroscopy to increase sensitivity even further. Alternatively, metal gratings can be employed to match photons for plasmon resonance. The real time monitoring of binding reactions not yet been reported in the combination of fluorescence detection and grating coupling. Grating-based systems promise more competitive products, because of reduced operating costs, and offer benefits for device engineering. This thesis is comprised of a comprehensive study of the suitability of grating coupling for fluorescence based analyte detection. Fundamental properties of grating coupled surface plasmon fluorescence spectroscopy are described, as well as issues related to the commercial realization of the method. Several new experimental techniques are introduced and demonstrated in order to optimize performance in certain areas and improve upon capabilities in respect to prism-based systems. Holographically fabricated gratings are characterized by atomic force microscopy and optical methods, aided by simulations and profile parameters responsible for efficient coupling are analyzed. The directional emission of fluorophores immobilized on a grating surface is studied in detail, including the magnitude and geometry of the fluorescence emission pattern for different grating constants and polarizations. Additionally, the separation between the minimum of the reflected intensity and the maximum fluorescence excitation position is examined. One of the key requirements for the commercial feasibility of grating coupling is the cheap and faithful mass production of disposable samples from a given master grating. The replication of gratings is demonstrated by a simple hot embossing method with good reproducibility to address this matter. The in-situ fluorescence detection of analyte immobilization and affinity measurements using grating coupling are described for the first time. The physical factors related to the sensitivity of the technique are assessed and the lower limit of detection of the technique is determined for an exemplary assay. Particular attention is paid to the contribution of bulk fluorophores to the total signal in terms of magnitude and polarization of incident and emitted light. Emission from the bulk can be a limiting factor for experiments with certain assay formats. For that reason, a novel optical method, based on the modulation of both polarization and intensity of the incident beam, is introduced and demonstrated to be capable of eliminating this contribution.

Untersuchungen zum Mechanismus der Zytotoxizität von alkylierenden Agenzien in malignen Melanomzellen

Maligne Melanome sind gegenüber Chemotherapeutika relativ resistent. Das methylierende Alkylanz Temozolomid sowie das chlorethylierende und DNA-Interstrand Crosslink (ICL) bildende Alkylanz Fotemustin kommen bei der Behandlung des malignen Melanoms als Mittel erster Wahl zum Einsatz. In der vorliegenden Arbeit konnte das erste Mal nachgewiesen werden, dass die zytotoxische Wirkung von Temozolomid und Fotemustin in Melanomzellen durch Apoptose vermittelt wird. Unter Verwendung klinisch relevanter Dosen der beiden Alkylantien konnte die Induktion von Apoptose durch vier unabhängige Methoden (Bestimmung der SubG1-Fraktion und der Apoptose- / Nekrose-Frequenz, Aktivierung der Effektorcaspasen-3 und -7 sowie Spaltung von PARP-1) nachgewiesen werden. Die Alkylierungen an der O6-Position des Guanins, welche durch beide Agenzien induziert werden, sind auch in Melanomzellen die wichtigsten Zytotoxizität-bewirkenden Läsionen in der DNA, und die O6-Methylguanin-DNA-Methyltransferase (MGMT) ist folglich ein herausragender Resistenzmarker. Eine der verwendeten Zelllinien (D05) exprimierte p53-Wildtypprotein. Diese Zelllinie war resistenter als alle anderen Zelllinien gegenüber Temozolomid und Fotemustin. Dies weist darauf hin, dass p53 nicht die Apoptoseinduktion in Melanomzellen verstärkt. Die Prozessierung des O6MeG erfolgt über die Mismatch-Reparatur (MMR) unter Generierung von DNA-Doppelstrangbrüchen (DSBs). Die Untersuchung der durch Temozolomid induzierten DSBs, nachgewiesen durch gammaH2AX-Induktion, korrelierte direkt mit der apoptotischen Antwort von Melanomzelllinien und DSBs können somit als eine entscheidende apoptoseauslösende Größe angesehen werden. Eine Resistenz gegenüber dem methylierenden Temozolomid in der Zelllinie MZ7 konnte auf einen Defekt in der MMR-Schadenserkennung auf der Ebene des MutSalpha-Komplexes zurückgeführt werden. Dieser Defekt hatte keinen Einfluss auf die Fotemustin-vermittelte Apoptoseinduktion. Neben MGMT konnte somit die MMR als Resistenzfaktor gegenüber methylierenden Agenzien in Melanomen identifiziert werden. Die Fotemustin-induzierte Apoptose wurde in Melanomzelllinien im Detail untersucht. Es konnte erstmals gezeigt werden, dass Fotemustin-bedingte ICLs in Zellen einen G2/M-Arrest im Behandlungszyklus induzieren. Wie anhand G1-arretierter Zellen nachgewiesen werden konnte, war das Durchlaufen der DNA-Replikation vor Erreichen des Arrests für die Induktion der Apoptose notwendig. Die Prozessierung von ICLs ist im Vergleich zu Methylierungen der DNA deutlich komplexer. Dies könnte erklären, warum in Melanomzellen die durch gammaH2AX-Induktion repräsentierten DSBs nicht mit der Sensitivität der einzelnen Zelllinien korreliert. Die Untersuchung unterschiedlich sensitiver Zelllinien zeigte ein vergleichbares Schadensniveau an ICLs und eine ebenso vergleichbare initiale Prozessierung derselben unter Generierung von DSBs. Die Prozessierung dieser sekundären Läsionen, welche anhand der Abnahme von gammaH2AX-Foci untersucht wurde, war hingegen in der sensitiveren Melanomzelllinie deutlich weniger effektiv. Es konnte weiterhin nachgewiesen werden, dass eine uneffektive Prozessierung der sekundären Läsionen einhergeht mit einer verstärkten und länger anhaltenden Aktivierung der in der DSB-Detektion beteiligten Kinase ATM und der Checkpoint Kinase 1. Es wäre daher denkbar, dass eine verstärkte Aktivität dieser Kinasen proapoptotische Signale vermittelt. Unterschiede in der Prozessierung der sekundären Läsionen könnten somit ein wichtiger Marker der ICL-induzierten Apoptose darstellen. Des weitern konnte nachgewiesen werden, dass nach Fotemustingabe die mitochondrial-vermittelte Apoptose einen effektiven Exekutionsweg in Melanomen darstellt. Während Cytochrom C-Freigabe, Bcl-2-Abnahme an den Mitochondrien, Bax-Rekrutierung und Caspase-9 Aktivität nachgewiesen werden konnten, wurden keine Hinweise auf eine Fas-Rezeptor-vermittelte Apoptose gefunden. Die Unfähigkeit, Rezeptor-vermittelte Apoptose zu unterlaufen, könnte die Bedeutungslosigkeit des p53-Gens in Melanomen begründen, da gerade dieser Weg in der Alkylantien-induzierten Apoptose in anderen Zellsystemen eine große Relevanz besitzt. Bei der Suche nach einem alternativen proapoptotischen Signalweg konnten Hinweise für die Beteiligung des Rb/E2F-1-Wegs, welcher über p73 agiert, in einer p53-mutierten Melanomzelllinie gefunden werden. Einen Einfluss der Proteine Survivin und XIAP als Resistenzfaktoren auf die Fotemustin-induzierte Apoptose wurde hingegen nicht nachgewiesen.

The Family Pasteurellaceae

This chapter describes the systematics and evolution of Pasteurellaceae with emphasis on new information generated since the 3rd edition of The Prokaryotes which only included chapters dealing with Haemophilus, Actinobacillus, and Pasteurella. A major source of new information for the current chapter has been provided by whole genome sequences now available for many taxa of the family. Some 100 species and species-like taxa have been documented and 18 genera of Pasteurellaceae reported so far. Members of the family include specialized commensals, potential pathogens, or pathogens of vertebrates and mainly survive poorly in other habitats including the external environment. The pathogenic members are of major importance to animal production and human health. Members of Pasteurellaceae have relatively small genomes, probably as a result of adaption to a special habitat. The most important species in veterinary microbiology include Pasteurella multocida, Actinobacillus pleuropneumoniae, [Haemophilus] parasuis, Mannheimia haemolytica, Bibersteinia trehalosi, and Avibacterium paragallinarum, while Haemophilus influenzae and Aggregatibacter actinomycetemcomitans represent the most important species as to human disease. Traditional isolation techniques are still used in both human and veterinary clinical diagnostic laboratories although genetically based diagnostic methods have replaced traditional biochemical/physiological methods for characterization and identification. For all species, MALDI-TOF can now be used as a diagnostic tool. As control and if MALDI-TOF equipment is not at hand, PCR-based specific detection is possible for Pasteurella multocida, Actinobacillus pleuropneumoniae, [Haemophilus] parasuis, Mannheimia haemolytica, Avibacterium paragallinarum, Gallibacterium anatis, Haemophilus influenzae, and Aggregatibacter actinomycetemcomitans. A lot of work has been directed towards identification of virulence factors and understanding host microbe interactions involved in disease.

Fully Automatic CT Segmentation for Computer-Assisted Pre-operative Planning of Hip Arthroscopy

Extraction of both pelvic and femoral surface models of a hip joint from CT data for computer-assisted pre-operative planning of hip arthroscopy is addressed. We present a method for a fully automatic image segmentation of a hip joint. Our method works by combining fast random forest (RF) regression based landmark detection, atlas-based segmentation, with articulated statistical shape model (aSSM) based hip joint reconstruction. The two fundamental contributions of our method are: (1) An improved fast Gaussian transform (IFGT) is used within the RF regression framework for a fast and accurate landmark detection, which then allows for a fully automatic initialization of the atlas-based segmentation; and (2) aSSM based fitting is used to preserve hip joint structure and to avoid penetration between the pelvic and femoral models. Validation on 30 hip CT images show that our method achieves high performance in segmenting pelvis, left proximal femur, and right proximal femur surfaces with an average accuracy of 0.59 mm, 0.62 mm, and 0.58 mm, respectively.