Experimental validation of a proposed single-phase five-level active rectifier operating with model predictive current control

This paper presents a model predictive current control applied to a proposed single-phase five-level active rectifier (FLAR). This current control strategy uses the discrete-time nature of the active rectifier to define its state in each sampling interval. Although the switching frequency is not constant, this current control strategy allows to follow the reference with low total harmonic distortion (THDF). The implementation of the active rectifier that was used to obtain the experimental results is described in detail along the paper, presenting the circuit topology, the principle of operation, the power theory, and the current control strategy. The experimental results confirm the robustness and good performance (with low current THDF and controlled output voltage) of the proposed single-phase FLAR operating with model predictive current control.

Long-Term Control of Endemic Hospital-Wide Methicillin-Resistant Staphylococcus aureus (MRSA): The Impact of Targeted Active Surveillance for MRSA in Patients and Healthcare Workers

To evaluate the long-term impact of successive interventions on rates of methicillin-resistant Staphylococcus aureus (MRSA) colonization or infection and MRSA bacteremia in an endemic hospital-wide situation. DESIGN:Quasi-experimental, interrupted time-series analysis. The impact of the interventions was analyzed by use of segmented regression. Representative MRSA isolates were typed by use of pulsed-field gel electrophoresis. SETTING:A 950-bed teaching hospital in Seville, Spain. PATIENTS:All patients admitted to the hospital during the period from 1995 through 2008. METHODS:Three successive interventions were studied: (1) contact precautions, with no active surveillance for MRSA; (2) targeted active surveillance for MRSA in patients and healthcare workers in specific wards, prioritized according to clinical epidemiology data; and (3) targeted active surveillance for MRSA in patients admitted from other medical centers. RESULTS:Neither the preintervention rate of MRSA colonization or infection (0.56 cases per 1,000 patient-days [95% confidence interval {CI}, 0.49-0.62 cases per 1,000 patient-days]) nor the slope for the rate of MRSA colonization or infection changed significantly after the first intervention. The rate decreased significantly to 0.28 cases per 1,000 patient-days (95% CI, 0.17-0.40 cases per 1,000 patient-days) after the second intervention and to 0.07 cases per 1,000 patient-days (95% CI, 0.06-0.08 cases per 1,000 patient-days) after the third intervention, and the rate remained at a similar level for 8 years. The MRSA bacteremia rate decreased by 80%, whereas the rate of bacteremia due to methicillin-susceptible S. aureus did not change. Eighty-three percent of the MRSA isolates identified were clonally related. All MRSA isolates obtained from healthcare workers were clonally related to those recovered from patients who were in their care. CONCLUSION:Our data indicate that long-term control of endemic MRSA is feasible in tertiary care centers. The use of targeted active surveillance for MRSA in patients and healthcare workers in specific wards (identified by means of analysis of clinical epidemiology data) and the use of decolonization were key to the success of the program.

Semiactive backstepping control for vibration attenuation in structures equipped with magnetorheological actuatorscat

This paper deals with the problem of semiactive vibration control of civil engineering structures subject to unknown external disturbances (for example, earthquakes, winds, etc.). Two kinds of semiactive controllers are proposed based on the backstepping control technique. The experimental setup used is a 6-story test structure equipped with shear-mode semiactive magnetorheological dampers being installed in the Washington University Structural Control and Earthquake Engineering Laboratory (WUSCEEL). The experimental results obtained have verified the effectiveness of the proposed control algorithms

A mixed H2/H∞-based semiactive control for vibration mitigation in flexible structures

In this paper, we address this problem through the design of a semiactive controller based on the mixed H2/H∞ control theory. The vibrations caused by the seismic motions are mitigated by a semiactive damper installed in the bottom of the structure. It is meant by semiactive damper, a device that absorbs but cannot inject energy into the system. Sufficient conditions for the design of a desired control are given in terms of linear matrix inequalities (LMIs). A controller that guarantees asymptotic stability and a mixed H2/H∞ performance is then developed. An algorithm is proposed to handle the semiactive nature of the actuator. The performance of the controller is experimentally evaluated in a real-time hybrid testing facility that consists of a physical specimen (a small-scale magnetorheological damper) and a numerical model (a large-scale three-story building)

Catechol-binding serines of beta(2)-adrenergic receptors control the equilibrium between active and inactive receptor states.

The binding free energy for the interaction between serines 204 and 207 of the fifth transmembrane helix of the beta(2)-adrenergic receptor (beta(2)-AR) and catecholic hydroxyl (OH) groups of adrenergic agonists was analyzed using double mutant cycles. Binding affinities for catecholic and noncatecholic agonists were measured in wild-type and mutant receptors, carrying alanine replacement of the two serines (S204A, S207A beta(2)-AR), a constitutive activating mutation, or both. The free energy coupling between the losses of binding energy attributable to OH deletion from the ligand and from the receptor indicates a strong interaction (nonadditivity) as expected for a direct binding between the two sets of groups. However, we also measured a significant interaction between the deletion of OH groups from the receptor and the constitutive activating mutation. This suggests that a fraction of the decrease in agonist affinity caused by serine mutagenesis may involve a shift in the conformational equilibrium of the receptor toward the inactive state. Direct measurements using a transient transfection assay confirm this prediction. The constitutive activity of the (S204A, S207A) beta(2)-AR mutant is 50 to 60% lower than that of the wild-type beta(2)-AR. We conclude that S204 and S207 do not only provide a docking site for the agonist, but also control the equilibrium of the receptor between active (R*) and inactive (R) forms.

Analysis of Active Magnet Bearing Control Software

Problems of the designing active magnet bearingcontrol are developed. The estimation controller are designed and applied to a rigid rotor. The mathematical model of the active magnet bearing controller is developed. This mathematical model is realized on a DSP. The results of this realization are analyzed. The conclusions about the digital signal processing are made.

Semiactive backstepping control for vibration attenuation in structures equipped with magnetorheological actuatorscat

This paper deals with the problem of semiactive vibration control of civil engineering structures subject to unknown external disturbances (for example, earthquakes, winds, etc.). Two kinds of semiactive controllers are proposed based on the backstepping control technique. The experimental setup used is a 6-story test structure equipped with shear-mode semiactive magnetorheological dampers being installed in the Washington University Structural Control and Earthquake Engineering Laboratory (WUSCEEL). The experimental results obtained have verified the effectiveness of the proposed control algorithms

A mixed H2/H∞-based semiactive control for vibration mitigation in flexible structures

In this paper, we address this problem through the design of a semiactive controller based on the mixed H2/H∞ control theory. The vibrations caused by the seismic motions are mitigated by a semiactive damper installed in the bottom of the structure. It is meant by semiactive damper, a device that absorbs but cannot inject energy into the system. Sufficient conditions for the design of a desired control are given in terms of linear matrix inequalities (LMIs). A controller that guarantees asymptotic stability and a mixed H2/H∞ performance is then developed. An algorithm is proposed to handle the semiactive nature of the actuator. The performance of the controller is experimentally evaluated in a real-time hybrid testing facility that consists of a physical specimen (a small-scale magnetorheological damper) and a numerical model (a large-scale three-story building)

Semiactive control strategies for vibration mitigation in adaptronic structures equipped with magnetorheological dampers

Los sistemas tales como edificios y veh¨ªculos est¨¢n sujetos a vibraciones que pueden causar mal funcionamiento, incomodidad o colapso. Para mitigar estas vibraciones, se suelen instalar amortiguadores. Estas estructuras se convierten en sistemas adaptr¨®nicos cuando los amortiguadores son controlables. Esta tesis se enfoca en la soluci¨®n del problema de vibraciones en edificios y veh¨ªculos usando amortiguadores magnetoreol¨®gicos (MR). Estos son unos amortiguadores controlables caracterizados por una din¨¢mica altamente no lineal. Adem¨¢s, los sistemas donde se instalan se caracterizan por la incertidumbre param¨¦trica, la limitaci¨®n de medidas y las perturbaciones desconocidas, lo que obliga al uso de t¨¦cnicas complejas de control. En esta tesis se usan Backstepping, QFT y H2/H¡Þ mixto para resolver el problema. Las leyes de control se verifican mediante simulaci¨®n y experimentaci¨®n.

A helmet mounted display system with active gaze control for visual telepresence

The objective of a Visual Telepresence System is to provide the operator with a high fidelity image from a remote stereo camera pair linked to a pan/tilt device such that the operator may reorient the camera position by use of head movement. Systems such as these which utilise virtual reality style helmet mounted displays have a number of limitations. The geometry of the camera positions and of the displays is generally fixed and is most suitable only for viewing elements of a scene at a particular distance. To address such limitations, a prototype system has been developed where the geometry of the displays and cameras is dynamically controlled by the eye movement of the operator. This paper explores why it is necessary to actively adjust the display system as well as the cameras and justifies the use of mechanical adjustment of the displays as an alternative to adjustment by electronic or image processing methods. The electronic and mechanical design is described including optical arrangements and control algorithms. The performance and accuracy of the system is assessed with respect to eye movement.

Performance analysis of the unconstrained FxLMS algorithm for active noise control

The paper analyzes the performance of the unconstrained filtered-x LMS (FxLMS) algorithm for active noise control (ANC), where we remove the constraints on the controller that it must be causal and has finite impulse response. It is shown that the unconstrained FxLMS algorithm always converges to, if stable, the true optimum filter, even if the estimation of the secondary path is not perfect, and its final mean square error is independent of the secondary path. Moreover, we show that the sufficient and necessary stability condition for the feedforward unconstrained FxLMS is that the maximum phase error of the secondary path estimation must be within 90°, which is the only necessary condition for the feedback unconstrained FxLMS. The significance of the analysis on a practical system is also discussed. Finally we show how the obtained results can guide us to design a robust feedback ANC headset.

Dynamic vergence telepresence system incorporating active gaze control

Visual Telepresence system which utilize virtual reality style helmet mounted displays have a number of limitations. The geometry of the camera positions and of the display is fixed and is most suitable only for viewing elements of a scene at a particular distance. In such a system, the operator's ability to gaze around without use of head movement is severely limited. A trade off must be made between a poor viewing resolution or a narrow width of viewing field. To address these limitations a prototype system where the geometry of the displays and cameras is dynamically controlled by the eye movement of the operator has been developed. This paper explores the reasons why is necessary to actively adjust both the display system and the cameras and furthermore justifies the use of mechanical adjustment of the displays as an alternative to adjustment by electronic or image processing methods. The electronic and mechanical design is described including optical arrangements and control algorithms, An assessment of the performance of the system against a fixed camera/display system when operators are assigned basic tasks involving depth and distance/size perception. The sensitivity to variations in transient performance of the display and camera vergence is also assessed.

Optimal design of smart structures using bonded plezoelectrics for vibration control

Smart material technology has become an area of increasing interest for the development of lighter and stronger structures which are able to incorporate actuator and sensor capabilities for collocated control. In the design of actively controlled structures, the determination of the actuator locations and the controller gains, is a very important issue. For that purpose, smart material modelling, modal analysis methods, control and optimization techniques are the most important ingredients to be taken into account. The optimization problem to be solved in this context presents two interdependent aspects. The first one is related to the discrete optimal actuator location selection problem which is solved in this paper using genetic algorithms. The second is represented by a continuous variable optimization problem, through which the control gains are determined using classical techniques. A cantilever Euler-Bernoulli beam is used to illustrate the presented methodology.