Controller design for variable-speed permanent magnet wind turbine generators interfaced with Z-source inverter

Increased awareness of environmental concerns has caused greater interest in developing power sources based on renewable technologies, such as wind. Due to the intermittent nature of the wind speed, output voltage and frequency of the direct driven permanent magnet synchronous generators (PMSG) are normally unsteady. Recently proposed Z-source inverter has been considered as a potential solution for grid interfacing wind power generators, thanks to buck-boost function that the single stage Z-source inverter can offer. Two control methodologies, namely unified controller for isolated operation and a multi-loop controller for grid interfaced operation are investigated in this paper. Theoretical analysis of these two control schemes is presented and experimental results to verify the effectiveness of the control method are also included.

Z-source converter based grid-interface for variable-speed permanent magnet wind turbine generators

A Z-source inverter based grid-interface for a variable-speed wind turbine connected to a permanent magnet synchronous generator is proposed. A control system is designed to harvest maximum wind energy under varied wind conditions with the use of the permanent magnet synchronous generator, diode-rectifier and Z-source inverter. Control systems for speed regulation of the generator and for DC- and AC- sides of the Z-source inverter are investigated using computer simulations and laboratory experiments. Simulation and experimental results verify the efficacy of the proposed approach.

A review of international speed enforcement policies and practices : evidence-based recommendations for best practice

Extensive research has highlighted the positive and exponential relationship between vehicle speed and crash risk and severity. Speed enforcement policies and practices throughout the world have developed dramatically as new technology becomes available, however speeding remains a pervasive problem internationally that significantly contributes to road trauma. This paper adopted a three-pronged approach to review speed enforcement policies and practices by: (i) describing and comparing policies and practices adopted in a cross-section of international jurisdictions; (ii) reviewing the available empirical evidence evaluating the effectiveness of various approaches, and; (iii) providing recommendations for the optimisation speed enforcement. The review shows the enforcement strategies adopted in various countries differ both in terms of the approaches used and how they are specifically applied. The literature review suggests strong and consistent evidence that police speed enforcement, in particular speed cameras, can be an effective tool for reducing vehicle speeds and subsequent traffic crashes. Drawing from this evidence, recommendations for best practice are proposed, including the specific instances in which various speed enforcement approaches typically produce the greatest road safety benefits, and perhaps most importantly, that speed enforcement programs must utilise a variety of strategies tailored to specific situations, rather than a one-size-fits-all approach.

New sale and leasing requirements for owners of swimming pools and their application to strata schemes

This article considers the changes to the Swimming Pools Act 1992 (NSW)(Act) which established a State-wide online register of all private swimming pools in NSW requiring pool owners to register their pools by 19 November 2013. Amendments to the Act introduced changes to the conveyancing and residential tenancy regulations to require vendors and landlords to have a valid Compliance Certificate issued for their swimming pool before offering the property for sale or lease. This article provides a brief overview of the new sale and leasing requirements effective from 29 April 2014, focusing on its application to lot owners within strata and community title schemes and other owners of water front properties with pools on Crown Land Reserves.

Influence of visible work activity on drivers’ speed choice at roadworks

Vehicle traffic through roadwork sites creates a hazardous work environment, with speed limit noncompliance a major contributor to the high risk and high severity of roadwork crashes. This paper examines responses to an online survey to better understand the factors underlying drivers’ work zone speed choices. Drivers’ stated speed choice was compared between two photographs of the same work zone section – one with workers and machinery present and another with no visible activity. Drivers also provided comments on any aspect of roadwork safety they thought was important. A paired t-test of stated speed choice revealed that significantly lower mean speeds were nominated when workers and machinery were clearly present and active (41.7 vs 53.5 km/h, p<0.01). Participants expressed concern about roadwork signage and reduced speed limits being left in place when there was no apparent work activity. Driver perceptions, and thus compliance, may be improved through technological and operational changes.

Characteristics of low-speed vehicle run-over events in children : an 11-year review

Objectives: The purpose of this study was to investigate the characteristics associated with fatal and non-fatal low-speed vehicle run-over (LSVRO) events in relation to person, incident and injury characteristics, in order to identify appropriate points for intervention and injury prevention. Methods: Data on all known LSVRO events in Queensland, Australia, over 11 calendar years (1999–2009) were extracted from five different databases representing the continuum of care ( prehospital to fatality) and manually linked. Descriptive and multivariate analyses were used to analyse the sample characteristics in relation to demographics, health service usage, outcomes, incident characteristics, and injury characteristics. Results: Of the 1641 LSVRO incidents, 98.4% (n=1615) were non-fatal, and 1.6% were fatal (n=26). Over half the children required admission to hospital (56%, n=921); mean length of stay was 3.4 days. Younger children aged 0–4 years were more frequently injured, and experienced more serious injuries with worse outcomes. Patterns of injury (injury type and severity), injury characteristics (eg, time of injury, vehicle type, driver of vehicle, incident location), and demographic characteristics (such as socioeconomic status, indigenous status, remoteness), varied according to age group. Almost half (45.6%; n=737) the events occurred outside major cities, and approximately 10% of events involved indigenous children. Parents were most commonly the vehicle drivers in fatal incidents. While larger vehicles such as four-wheel drives (4WD) were most frequently involved in LSVRO events resulting in fatalities, cars were most frequently involved in non-fatal events. Conclusions: This is the first study, to the authors’ knowledge, to analyse the characteristics of fatal and non-fatal LSVRO events in children aged 0–15 years on a state-wide basis. Characteristics of LSVRO events varied with age, thus age-specific interventions are required. Children living outside major cities, and indigenous children, were over-represented in these data. Further research is required to identify the burden of injury in these groups.

Incidence of paediatric fatal and non-fatal low speed vehicle run over events in Queensland, Australia : eleven year analysis

Background The purpose of this study was to estimate the incidence of fatal and non-fatal Low Speed Vehicle Run Over (LSVRO) events among children aged 0–15 years in Queensland, Australia, at a population level. Methods Fatal and non-fatal LSVRO events that occurred in children resident in Queensland over eleven calendar years (1999-2009) were identified using ICD codes, text description, word searches and medical notes clarification, obtained from five health related data bases across the continuum of care (pre-hospital to fatality). Data were manually linked. Population data provided by the Australian Bureau of Statistics were used to calculate crude incidence rates for fatal and non-fatal LSVRO events. Results There were 1611 LSVROs between 1999–2009 (IR = 16.87/100,000/annum). Incidence of non-fatal events (IR = 16.60/100,000/annum) was 61.5 times higher than fatal events (IR = 0.27/100,000/annum). LSVRO events were more common in boys (IR = 20.97/100,000/annum) than girls (IR = 12.55/100,000/annum), and among younger children aged 0–4 years (IR = 21.45/100000/annum; 39% or all events) than older children (5–9 years: IR = 16.47/100,000/annum; 10–15 years IR = 13.59/100,000/annum). A total of 896 (56.8%) children were admitted to hospital for 24 hours of more following an LSVRO event (IR = 9.38/100,000/annum). Total LSVROs increased from 1999 (IR = 14.79/100,000) to 2009 (IR = 18.56/100,000), but not significantly. Over the 11 year period, there was a slight (non –significant) increase in fatalities (IR = 0.37-0.42/100,000/annum); a significant decrease in admissions (IR = 12.39–5.36/100,000/annum), and significant increase in non-admissions (IR = 2.02-12.77/100,000/annum). Trends over time differed by age, gender and severity. Conclusion This is the most comprehensive, population-based epidemiological study on fatal and non-fatal LSVRO events to date. Results from this study indicate that LSVROs incur a substantial burden. Further research is required on the characteristics and risk factors associated with these events, in order to adequately inform injury prevention. Strategies are urgently required in order to prevent these events, especially among young children aged 0-4 years.

Effect of mobile phone use and aggression on speed selection by young drivers : a driving simulator study

Aggressive driving has been associated with engagement in other risky driving behaviours, such as speeding; while drivers using their mobile phones have an increased crash risk, despite the tendency to reduce their speed. Research has amassed separately for mobile phone use and aggressive driving among younger drivers, however little is known about the extent to which these behaviours may function independently and in combination to influence speed selection behaviour. The main aim of the current study was to investigate the effect of driver aggression (measured by the Driving Anger Expression Inventory) and mobile phone use on speed selection by young drivers. The CARRS-Q advanced driving simulator was used to test the speed selection of drivers aged 18 to 26 years (N = 32) in a suburban (60kph zone) driving context. A 2 (level of driving anger expression: low, high) X 3 (mobile phone use condition: baseline, hands-free, hand-held) mixed factorial ANOVA was conducted with speed selection as the dependent variable. Results revealed a significant main effect for mobile phone use condition such that speed selection was lowest for the hand-held condition and highest for the baseline condition. Speed selection, however, was not significantly different across the levels of driving anger expression; nor was there a significant interaction effect between the mobile phone use and driving anger expression. As young drivers are over-represented in road crash statistics, future research should further investigate the combined impact of driver aggression and mobile phone use on speed selection.

A sensitivity analysis of train speed and its effect on railway capacity

Increasing train speeds is conceptually a simple and straight forward method to expand railway capacity, for example in comparison to other more extensive and elaborate alternatives. In this article an analytical capacity model has been investigated as a means of performing a sensitivity analysis of train speeds. The results of this sensitivity analysis can help improve the operation of this railway system and to help it cope with additional demands in the future. To test our approach a case study of the Rah Ahane Iran (RAI) national railway network has been selected. The absolute capacity levels for this railway network have been determined and the analysis shows that increasing trains speeds may not be entirely cost effective in all circumstances.

A new look at the restrictions on the speed and magnitude of train loads for bridge management

In current bridge management systems (BMSs), load and speed restrictions are applied on unhealthy bridges to keep the structure safe and serviceable for as long as possible. But the question is, whether applying these restrictions will always decrease the internal forces in critical components of the bridge and enhance the safety of the unhealthy bridges. To find the answer, this paper for the first time in literature, looks into the design aspects through studying the changes in demand by capacity ratios of the critical components of a bridge under the train loads. For this purpose, a structural model of a simply supported bridge, whose dynamic behaviour is similar to a group of real railway bridges, is developed. Demand by capacity ratios of the critical components of the bridge are calculated, to identify their sensitivity to increase of speed and magnitude of live load. The outcomes of this study are very significant as they show that, on the contrary to what is expected, by applying restriction on speed, the demand by capacity ratio of components may increase and make the bridge unsafe for carrying live load. Suggestions are made to solve the problem.

The effects of flight speed on ranging performance of bats using frequency modulated echolocation pulses

Many species of bat use ultrasonic frequency modulated (FM) pulses to measure the distance to objects by timing the emission and reception of each pulse. Echolocation is mainly used in flight. Since the flight speed of bats often exceeds 1% of the speed of sound, Doppler effects will lead to compression of the time between emission and reception as well as an elevation of the echo frequencies, resulting in a distortion of the perceived range. This paper describes the consequences of these Doppler effects on the ranging performance of bats using different pulse designs. The consequences of Doppler effects on ranging performance described in this paper assume bats to have a very accurate ranging resolution, which is feasible with a filterbank receiver. By modeling two receiver types, it was first established that the effects of Doppler compression are virtually independent of the receiver type. Then, used a cross-correlation model was used to investigate the effect of flight speed on Doppler tolerance and range–Doppler coupling separately. This paper further shows how pulse duration, bandwidth, function type, and harmonics influence Doppler tolerance and range–Doppler coupling. The influence of each signal parameter is illustrated using calls of several bat species. It is argued that range–Doppler coupling is a significant source of error in bat echolocation, and various strategies bats could employ to deal with this problem, including the use of range rate information are discussed.

Reliable Fault Diagnosis for Low-Speed Bearings Using Individually Trained Support Vector Machines With Kernel Discriminative Feature Analysis

This paper proposes a highly reliable fault diagnosis approach for low-speed bearings. The proposed approach first extracts wavelet-based fault features that represent diverse symptoms of multiple low-speed bearing defects. The most useful fault features for diagnosis are then selected by utilizing a genetic algorithm (GA)-based kernel discriminative feature analysis cooperating with one-against-all multicategory support vector machines (OAA MCSVMs). Finally, each support vector machine is individually trained with its own feature vector that includes the most discriminative fault features, offering the highest classification performance. In this study, the effectiveness of the proposed GA-based kernel discriminative feature analysis and the classification ability of individually trained OAA MCSVMs are addressed in terms of average classification accuracy. In addition, the proposedGA- based kernel discriminative feature analysis is compared with four other state-of-the-art feature analysis approaches. Experimental results indicate that the proposed approach is superior to other feature analysis methodologies, yielding an average classification accuracy of 98.06% and 94.49% under rotational speeds of 50 revolutions-per-minute (RPM) and 80 RPM, respectively. Furthermore, the individually trained MCSVMs with their own optimal fault features based on the proposed GA-based kernel discriminative feature analysis outperform the standard OAA MCSVMs, showing an average accuracy of 98.66% and 95.01% for bearings under rotational speeds of 50 RPM and 80 RPM, respectively.

The influence of flight speed on the ranging performance of bats using frequency modulated echolocation pulses

Many species of bat use ultrasonic frequency modulated (FM) pulses to measure the distance to objects by timing the emission and reception of each pulse. Echolocation is mainly used in flight. Since the flight speed of bats often exceeds 1% of the speed of sound,Doppler effects will lead to compression of the time between emission and reception as well as an elevation of the echo frequencies, resulting in a distortion of the perceived range. This paper describes the consequences of these Doppler effects on the ranging performance of bats using different pulse designs. The consequences of Doppler effects on ranging performance described in this paper assume bats to have a very accurate ranging resolution, which is feasible with a filterbank receiver. By modeling two receiver types, it was first established that the effects of Doppler compression are virtually independent of the receiver type. Then, used a cross-correlation model was used to investigate the effect of flight speed on Doppler tolerance and range–Doppler coupling separately. This paper further shows how pulse duration, bandwidth, function type, and harmonics influence Doppler tolerance and range–Doppler coupling. The influence of each signal parameter is illustrated using calls of several bat species. It is argued that range–Doppler coupling is a significant source of error in bat echolocation, and various strategies bats could employ to deal with this problem, including the use of range rate information are discussed.

Effect of mobile phone use and aggression on speed selection by young drivers : a driving simulator study

Aggressive driving has been associated with engagement in other risky driving behaviours, such as speeding; while drivers using their mobile phones have an increased crash risk, despite the tendency to reduce their speed. Research has amassed separately for mobile phone use and aggressive driving among younger drivers, however little is known about the extent to which these behaviours may function independently and in combination to influence speed selection behaviour. The main aim of the current study was to investigate the effect of driver aggression (measured by the Driving Anger Expression Inventory) and mobile phone use on speed selection by young drivers. The CARRS-Q advanced driving simulator was used to test the speed selection of drivers aged 18 to 26 years (N = 32) in a suburban (60kph zone) driving context. A 2 (level of driving anger expression: low, high) X 3 (mobile phone use condition: baseline, hands-free, hand-held) mixed factorial ANOVA was conducted with speed selection as the dependent variable. Results revealed a significant main effect for mobile phone use condition such that speed selection was lowest for the hand-held condition and highest for the baseline condition. Speed selection, however, was not significantly different across the levels of driving anger expression; nor was there a significant interaction effect between the mobile phone use and driving anger expression. As young drivers are over-represented in road crash statistics, future research should further investigate the combined impact of driver aggression and mobile phone use on speed selection.

ICEPOLE: High-speed, hardware-oriented authenticated encryption

This paper introduces our dedicated authenticated encryption scheme ICEPOLE. ICEPOLE is a high-speed hardware-oriented scheme, suitable for high-throughput network nodes or generally any environment where specialized hardware (such as FPGAs or ASICs) can be used to provide high data processing rates. ICEPOLE-128 (the primary ICEPOLE variant) is very fast. On the modern FPGA device Virtex 6, a basic iterative architecture of ICEPOLE reaches 41 Gbits/s, which is over 10 times faster than the equivalent implementation of AES-128-GCM. The throughput-to-area ratio is also substantially better when compared to AES-128-GCM. We have carefully examined the security of the algorithm through a range of cryptanalytic techniques and our findings indicate that ICEPOLE offers high security level.