Quadrant/octant sequencing and the role of coherent structures in bed load sediment entrainment

To permit the tracking of turbulent flow structures in an Eulerian frame from single-point measurements, we make use of a generalization of conventional two-dimensional quadrant analysis to three-dimensional octants. We characterize flow structures using the sequences of these octants and show how significance may be attached to particular sequences using statistical mull models. We analyze an example experiment and show how a particular dominant flow structure can be identified from the conditional probability of octant sequences. The frequency of this structure corresponds to the dominant peak in the velocity spectra and exerts a high proportion of the total shear stress. We link this structure explicitly to the propensity for sediment entrainment and show that greater insight into sediment entrainment can be obtained by disaggregating those octants that occur within the identified macroturbulence structure from those that do not. Hence, this work goes beyond critiques of Reynolds stress approaches to bed load entrainment that highlight the importance of outward interactions, to identifying and prioritizing the quadrants/octants that define particular flow structures. Key Points <list list-type=''bulleted'' id=''jgrf20196-list-0001''> <list-item id=''jgrf20196-li-0001''>A new method for analysing single point velocity data is presented <list-item id=''jgrf20196-li-0002''>Flow structures are identified by a sequence of flow states (termed octants) <list-item id=''jgrf20196-li-0003''>The identified structure exerts high stresses and causes bed-load entrainment

Equivalent roughness of gravel-bed rivers

The relation between the equivalent roughness and different grain size percentiles of the sediment in gravel-bed rivers was determined under the hypothesis that the vertical distribution of the flow velocity follows a logarithmic law. A set of 954 data points was selected from rivers with gravel size sediment or larger, with a non-sinuous alignment and free of vegetation or obstacles. According to the results, the ks roughness is equivalent to approximately 2.4D90, 2.8D84, and 6.1D50. No correlation was detected between the sediment sorting and the sediment mobility index on one hand, and, on the other, the coefficient of proportionality of each grain size percentile.

luporum : Configuració UCI mitjançant una API REST

L'empresa Routek SL manté una distribució anomenada qMp basada en la distribució OpenWRT. Tant la distribució OpenWRT, com l'ampliació de Routek SL qMp, disposen d'un sistema de configuració anomenat Unified Configuration Interface (UCI). Una de les característiques d'aquest sistema és que les configuracions dels programes que l'usen segueixen una mateixa sintaxi. El projecte luporum descrit en aquesta memòria explica com s'ha realitzat el desenvolupament d'una API REST que facilita que es pugui gestionar aquesta configuració remotament, fent peticions HTTP.

Task-induced deactivation from rest extends beyond the default mode brain network

Activity decreases, or deactivations, of midline and parietal cortical brain regions are routinely observed in human functional neuroimaging studies that compare periods of task-based cognitive performance with passive states, such as rest. It is now widely held that such task-induced deactivations index a highly organized"default-mode network" (DMN): a large-scale brain system whose discovery has had broad implications in the study of human brain function and behavior. In this work, we show that common task-induced deactivations from rest also occur outside of the DMN as a function of increased task demand. Fifty healthy adult subjects performed two distinct functional magnetic resonance imaging tasks that were designed to reliably map deactivations from a resting baseline. As primary findings, increases in task demand consistently modulated the regional anatomy of DMN deactivation. At high levels of task demand, robust deactivation was observed in non-DMN regions, most notably, the posterior insular cortex. Deactivation of this region was directly implicated in a performance-based analysis of experienced task difficulty. Together, these findings suggest that task-induced deactivations from rest are not limited to the DMN and extend to brain regions typically associated with integrative sensory and interoceptive processes.

Treatment of rats with a self-selected hyperlipidic diet, increases the lipid content of the main adipose tissue sites in a proportion similar to that of the lipids in the rest of organs and tissues

Adipose tissue (AT) is distributed as large differentiated masses, and smaller depots covering vessels, and organs, as well as interspersed within them. The differences between types and size of cells makes AT one of the most disperse and complex organs. Lipid storage is partly shared by other tissues such as muscle and liver. We intended to obtain an approximate estimation of the size of lipid reserves stored outside the main fat depots. Both male and female rats were made overweight by 4-weeks feeding of a cafeteria diet. Total lipid content was analyzed in brain, liver, gastrocnemius muscle, four white AT sites: subcutaneous, perigonadal, retroperitoneal and mesenteric, two brown AT sites (interscapular and perirenal) and in a pool of the rest of organs and tissues (after discarding gut contents). Organ lipid content was estimated and tabulated for each individual rat. Food intake was measured daily. There was a surprisingly high proportion of lipid not accounted for by the main macroscopic AT sites, even when brain, liver and BAT main sites were discounted. Muscle contained about 8% of body lipids, liver 1-1.4%, four white AT sites lipid 28-63% of body lipid, and the rest of the body (including muscle) 38-44%. There was a good correlation between AT lipid and body lipid, but lipid in"other organs" was highly correlated too with body lipid. Brain lipid was not. Irrespective of dietary intake, accumulation of body fat was uniform both for the main lipid storage and handling organs: large masses of AT (but also liver, muscle), as well as in the"rest" of tissues. These storage sites, in specialized (adipose) or not-specialized (liver, muscle) tissues reacted in parallel against a hyperlipidic diet challenge. We postulate that body lipid stores are handled and regulated coordinately, with a more centralized and overall mechanisms than usually assumed.

CFD study of penetration and mixing of fuel in a circulating fluidized bed furnace

The aim of this thesis is to study the mixing of fuel and, also to some extent, the mixing of air in a circulating fluidized bed boiler. In the literature survey part of this thesis, a review is made of the previous experimental studies related to the fuel and air mixing in the circulating fluidized beds. In the simulation part of it the commercial computational fluid dynamics software (FLUENT) is used with the Eulerian multiphase model for studying the fuel mixing in the two and three-dimensional furnace geometries. The results of the three-dimensional simulations are promising and, therefore suggestions are made for the future simulations. The two-dimensional studies give new information of the effects of the fluidization velocity, fuel particle size and fuel density on the fuel mixing. However, the present results show that three-dimensional models produce more realistic representation of the circulating fluidized bed behavior.

Nutritional potential of green banana flour obtained by drying in spouted bed

This study evaluated the chemical composition of peeled and unpeeled green banana Cavendish (AAA) flour obtained by drying in spouted bed, aiming at adding nutritional value to food products. The bananas were sliced and crushed to obtain a paste and fed to the spouted bed dryer (12 cm height and T = 80 ºC) in order to obtain flour. The flours obtained were subjected to analysis of moisture, protein, ash, carbohydrates, total starch, resistant starch, fiber. The green banana flours, mainly unpeeled, are good sources of fiber and resistant starch with an average of 21.91g/100g and 68.02g/100g respectively. The protein content was found in an average of 4.76g/100g, being classified as a low biological value protein with lysine as the first limiting amino acid. The results showed that unpeeled green banana flour obtained by spouted bed drying can be a valuable tool to add nutritional value to products in order to increase their non-digestible fraction.

Advanced control methods for reducing nitrogen oxides in a fluidized bed boiler

Tämän työn tarkoituksena oli löytää keinoja erään leijukerroskattilan typenoksidipäästöjen vähentämiseksi. Koska päästöt olivat jo alunperin alhaiset leijukerrostekniikan ja hybridin SNCR/SCR –typenpoistolaitteiston ansiosta, päätettiin päästöjä lähteä vähentämään parantamalla ammoniakkiruiskutuksen säätöä. Alkuperäinen ammoniakkiruiskutuksen säätö oli liian hidas, jotta satunnaisten häiriöiden aiheuttamat typenoksidipiikit olisi pystytty poistamaan. Ammoniakkiruiskutusta parannettiin lisäämällä jokaiseen ammoniakkilinjaan mäntäpumput, joiden avulla ammoniakkia voidaan syöttää sinne, missä sitä eniten tarvitaan. Ammoniakkiruiskutuksen säätöön kehitettiin uusi sumeaan logiikkaan perustuva säätäjä. Myös muita kehittyneitä säätömenetelmiä kuten neuroverkkoa hyödynnettiin säätäjän kehityksessä. Ammoniakkiruiskutuksen säätäjää testattiin menestyksekkäästi Ruotsissa Brista Kraftin Märstassa sijaitsevalla voimalaitoksella

Development of Furnace Model for Bubbling Fluidized Bed Boiler

The aim of this thesis was to develop a model, which can predict heat transfer, heat release distribution and vertical temperature profile of gas phase in the furnace of a bubbling fluidized bed (BFB) boiler. The model is based on three separate model components that take care of heat transfer, heat release distribution and mass and energy balance calculations taking into account the boiler design and operating conditions. The model was successfully validated by solving the model parameters on the basis of commercial size BFB boiler test run information and by performing parametric studies with the model. Implementation of the developed model for the Foster Wheeler BFB design procedures will require model validation with existing BFB database and possibly more detailed measurements at the commercial size BFB boilers.

Characterization Method for Comminution Behavior of Limestone and Fuel Ash in a Circulating Fluidized Bed Boiler

Työn tavoite oli kehittää karakterisointimenetelmät kalkkikiven ja polttoaineen tuhkan jauhautumisen ennustamiselle kiertoleijukattilan tulipesässä. Kiintoainekäyttäytymisen karakterisoinnilla ja mallintamisella voidaan tarkentaa tulipesän lämmönsiirron ja tuhkajaon ennustamista. Osittain kokeelliset karakterisointimenetelmät perustuvat kalkkikiven jauhautumiseen laboratoriokokoluokan leijutetussa kvartsiputkireaktorissa ja tuhkan jauhatumiseen rotaatiomyllyssä. Karakterisointimenetelmät ottavat huomioon eri-laiset toimintaolosuhteet kaupallisen kokoluokan kiertoleijukattiloissa. Menetelmät kelpoistettiin kaupallisen kokoluokan kiertoleijukattiloista mitattujen ja fraktioittaisella kiintoainemallilla mallinnettujen taseiden avulla. Kelpoistamistaseiden vähäisyydestä huolimatta karakterisointimenetelmät arvioitiin virhetarkastelujen perusteella järkeviksi. Karakterisointimenetelmien kehittämistä ja tarkentamista tullaan jatkamaan.

Comparison of different methods to forecast hospital bed needs

Objectives : This study compares three methods to forecast the number of acute somatic hospital beds needed in a Swiss academic hospital over the period 2010-2030. Design : Information about inpatient stays is provided through a yearly mandatory reporting of Swiss hospitals, containing anonymized data. Forecast of the numbers of beds needed compares a basic scenario relying on population projections with two other methods in use in our country that integrate additional hypotheses on future trends in admission rates and length of stay (LOS).

Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.