Strong visible up-conversion emissions and thermometric applications of Er3+-Yb3+ codoped Al2O3 prepared by the sol-gel method

The Er3+-Yb3+ codoped Al2O3 has been prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)(3)]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)(3) center dot 5H(2)O] and ytterbium nitrate [Yb(NO3)(3) center dot 5H(2)O]. The phase structure, including only two crystalline types of doped Al2O3 phases, theta and gamma, was obtained for the 1 mol% Er3+ and 5 mol% Yb3+ codoped Al2O3 at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300-825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er3+-Yb3+ codoped Al2O3 plays an important role in the application of high temperature sensor.

Optical transitions of Er3+ and Yb3+ ions in novel oxyfluoride bismuth-germanium glass: Observation of up-conversion

Er3+/Yb3+-codoped novel oxyfluoride bismuth-germanium glass was prepared and its up-conversion fluorescence property under 975 nm excitation has been studied. Intense green and weak red emissions centered at 525, 546, and 657 nm, corresponding to the transitions 2H(11/2) -> I-4(15/2), S-4(3/2) -> I-4(15/2), and F-4(9/2) -> I-4(15/2), respectively, were observed at room temperature. The possible up-conversion mechanism was also evaluated. The optimal Yb3+-Er3+ concentration ratio is found based on the direct lifetime measurements of excited levels for Er3+ ion. The structure of this novel oxyfluoride bismuth-germanium glass has been investigated by peak-deconvolution of FT-Raman spectrum, and the structural information was obtained from the peak wavenumbers. This novel oxyfluoride bismuth-germanium glass with relatively lower maximum phonon energy (similar to 731 cm(-1)) can be used as potential host material for up-conversion lasers. (c) 2005 Elsevier B.V. All rights reserved.

Rapid quantitative detection of Yersinia pestis by lateral-flow immunoassay and up-converting phosphor technology-based biosensor

Up-converting phosphor technology (UPT)-based lateral-flow immunoassay has been developed for quantitative detection of Yersinia pestis rapidly and specifically. In this assay, 400 nm up-converting phosphor particles were used as the reporter. A sandwich immumoassay was employed by using a polyclonal antibody against F1 antigen of Y. pestis immobilized on the nitrocellulose membrane and the same antibody conjugated to the UPT particles. The signal detection of the strips was performed by the UPT-based biosensor that could provide a 980 nm IR laser to excite the phosphor particles, then collect the visible luminescence emitted by the UPT particles and finally convert it to the voltage as a signal. V-T and V-c stand for the multiplied voltage units for the test and the control line, respectively, and the ratio V-T/V-C is directly proportional to the number of Y pestis in a sample. We observed a good linearity between the ratio and log CFU/ml of Y pestis above the detection limit, which was approximately 10(4) CFU/mI. The precision of the intra- and inter-assay was below 15% (coefficient of variation, CV). Cross-reactivity with related Gram-negative enteric bacteria was not found. The UPT-LF immunoassay system presented here takes less than 30 min to perform from the sample treatment to the data analysis. The current paper includes only preliminary data concerning the biomedical aspects of the assay, but is more concentrated on the technical details of establishing a rapid manual assay using a state-of-the-art label chemistry. (c) 2006 Elsevier B.V. All rights reserved.

Sperm cryopreservation of Indian major carp, Labeo rohita: cryodiluents, sperm: cryodiluent dilution ratio and cryoprotectan t concentration

Cryogenic preservation trials of spermatozoa of Labeo rohita were carried out. Twenty four cryodiluents (extender + cryoprotectant), with the combination of six extenders such as egg-yolk citrate, urea-egg-yolk, 0.9% NaCl, Kurokura-2, Ma and Mb and four cryoprotectants viz. DMSO, glycerol, methanol and ethanol, were used to screen out the suitable cryodiluents. Sperm was preserved in 0.25ml plastic straw in programmable freezer. Two step freezing method was followed. Sperm preserved with egg-yolk citrate and urea-egg-yolk containing 10% DMSO showed best post-thaw motility (80%) followed by 0.9% NaCl (60%) and Kurokura-2(30%) solutions. Sperm with the extenders M" and Mb clotted at the time of equilibration and also after few days of preservation. Egg-yolk citrate mixed with ethanol and methanol also showed good percentage of motility (80%) but egg-yolk citrate with glycerol showed less sperm motility (>60%). To determine suitable dilution ratio of milt and cryodiluent two best extender eggyolk citrate and urea-egg-yolk with four cryoprotectants such as DMSO, glycerol, methanol and ethanol at different ratio viz 1:2,1:4,1:7,1:10,1:15 and 1:20 were used. Highest post-thaw motility (>80%) was observed when milt was preserved with egg-yolk citrate containing 10% DMSO at 1:2, 1:4, 1:7 and 1:10 dilutions. Meanwhile using glycerol as cryoprotectants provided less post thaw motility at lower dilution ratio but with the increase of its dilution showed good sperm motility compared with other cryoprotectants. Finally, evaluation on the effect of cryoprotectant concentration on post-thaw sperm motility was conducted. Egg-yolk citrate and four cryoprotectant i.e. DMSO, glycerol, methanol and ethanol with six different concentrations namely 5%,7%, 10%, 15%, 20% and 30%.were evaluated. Among the cryoprotectants DMSO, methanol and ethanol showed highest post-thaw motility (about 80%) at 7% and 10% concentrations. Although glycerol was not suitable at low concentration but its 20% and 30% concentration levels provided best post-thaw motility. No post-thaw motility was obtained with DMSO at 30% concentration. The overall analysis on cryoprotectant concentration indicated that below 5% and above 20% cryoprotectant concentrations could not be suitable for effective cryopreservation of spermatozoa.

Optimum dietary carbohydrate to lipid ratio in stinging catfish, Heteropneustes fossilis (Bloch, 1792)

A feeding trial of 8 weeks was conducted in a static indoor rearing system to investigate the optimum carbohydrate to lipid ratio (CHO:L ratio) in stinging catfish, Heteropneustes fossilis. Five iso-nitrogenous (35% crude protein) and iso-energetic (17.06 kJ gˉ¹ gross energy (GE)) fish meal based diets with varying carbohydrate to lipid (CHO:L g/g) ratios of 0.60, 0.98, 1.53, 2.29 and 3.44 for diets 1-5, were tested, respectively. The diets containing a fixed protein to energy ratio (P:E ratio) of 20.50-mg protein kJˉ¹ GE were fed to triplicate groups of 40 fish (per 70-L tank). Fish were fed 5% of their body weight per day adjusted fortnightly. Diet 1, containing 10% carbohydrate and 17% lipids with a CHO:L ratio of 0.60 produced the poorest (p<0.05) growth rates, feed and protein efficiency. Increasing carbohydrate content in the diets to 26% concomitant with a reduction in lipid content to 11% with a CHO:L ration of 2.29 of diet 5 significantly improved (p<0.05) growth rates, feed and protein efficiency. But did not differ with diet 4, containing CHO:L ratio 2.29. A further increase in dietary carbohydrate up to 31% and a decrease in lipids levels to 9% with a CHO:L ratio ranging from 2.29 to 3.44 (diet 4-5) did not significantly improve the fish performance. Apparent net protein utilisation (ANPU) of fish fed diet 5 was higher (p<0.05) than for diets 1 and 2 but did not differ from diets 3 and 4. Higher lipid deposition (p<0.05) in whole body was observed with decreasing dietary CHO:L ratios as increasing lipid levels. Whole body protein of fish fed varying CHO:L diets did not show any discernible changes among the dietary treatments. This study revealed that H. fossilis can perform equally well on diets containing carbohydrate ranging from 26 to 31%, with 9 to 11% lipid or at CHO:L g/g ratio of 2.29-3.44.

SuperJunction IGBTS: An evolutionary step of silicon power devices with high impact potential

15 years ago the vertical SuperJunction (SJ) concept conceived for SJ power MOSFETs was the last, major breakthrough in the field of silicon power devices. Today, the SuperJunction MOSFET technologies have reached a mature stage characterized by gradual performance improvements. SuperJunction Insulated Gate Bipolar Transistors (SJ IGBTs) could interrupt this stagnation holding promise to revitalize voltage classes from 600 up to 1200 V. Such SJ IGBTs surpass by a very significant margin their SJ MOSFET counterparts both in terms of power handling capability, on-state and turn-off losses, all at the same time. On the higher end of the voltage class, SJ IGBTs would top the performance of 1.2 kV IGBTs by a similar margin. © 2012 IEEE.

A simple criterion for filament break-up in drop-on-demand inkjet printing

Jets from drop-on-demand inkjet print-heads consist of a main drop with a trailing filament, which either condenses into the main drop, or breaks up into satellite drops. Filament behaviour is quantitatively similar to that of larger, free symmetrical filamentscan be predicted from the aspect ratio and Ohnesorge number. Symmetrical filaments generated from inkjet print-heads show the same behaviour. A simple model, based on competition between the processes of axial shortening and radial necking, predicts the critical aspect ratio below which the jet condenses into a single drop. The success of this simple criterion supports the underlying physical model. © 2013 American Institute of Physics.

Particulate matter emission during start-up and transient operation of a spark-ignition engine

In order to understand why emissions of Particulate Matter (PM) from Spark-Ignition (SI) automobiles peak during periods of transient operation such as rapid accelerations, a study of controlled, repeatable transients was performed. Time-resolved engine-out PM emissions from a modern four-cylinder engine during transient load and air/fuel ratio operation were examined, and the results could be fit in most cases to a first order time response. The time constants for the transient response are similar to those measured for changes in intake valve temperature, reflecting the strong dependence of PM emissions on the amount of liquid fuel in the combustion chamber. In only one unrepeatable case did the time response differ from a first order function: showing an overshoot in PM emissions during transition from the initial to the final steady state PM emission level. PM emissions during controlled, motored start-up experiments show a peak at start-up followed by a period during which emissions are either relatively constant or drift somewhat. When the fuel injection and ignition are shut off, PM emissions also peak briefly, but rapidly decay to low levels. Qualitative implications on the study and modeling of PM emissions during transient engine operation are discussed. Copyright © 1999 Society of Automotive Engineers, Inc.

Effect of95 241Am(n, γ) reaction branching ratio on fuel cycle and reactor design characteristics

The growing interest in innovative reactors and advanced fuel cycle designs requires more accurate prediction of various transuranic actinide concentrations during irradiation or following discharge because of their effect on reactivity or spent-fuel emissions, such as gamma and neutron activity and decay heat. In this respect, many of the important actinides originate from the 241Am(n,γ) reaction, which leads to either the ground or the metastable state of 242Am. The branching ratio for this reaction depends on the incident neutron energy and has very large uncertainty in the current evaluated nuclear data files. This study examines the effect of accounting for the energy dependence of the 241Am(n,γ) reaction branching ratio calculated from different evaluated data files for different reactor and fuel types on the reactivity and concentrations of some important actinides. The results of the study confirm that the uncertainty in knowing the 241Am(n,γ) reaction branching ratio has a negligible effect on the characteristics of conventional light water reactor fuel. However, in advanced reactors with large loadings of actinides in general, and 241Am in particular, the branching ratio data calculated from the different data files may lead to significant differences in the prediction of the fuel criticality and isotopic composition. Moreover, it was found that neutron energy spectrum weighting of the branching ratio in each analyzed case is particularly important and may result in up to a factor of 2 difference in the branching ratio value. Currently, most of the neutronic codes have a single branching ratio value in their data libraries, which is sometimes difficult or impossible to update in accordance with the neutron spectrum shape for the analyzed system.

Graphene nanoribbon blends with P3HT for organic electronics.

In organic field-effect transistors (OFETs) the electrical characteristics of polymeric semiconducting materials suffer from the presence of structural/morphological defects and grain boundaries as well as amorphous domains within the film, hindering an efficient transport of charges. To improve the percolation of charges we blend a regioregular poly(3-hexylthiophene) (P3HT) with newly designed N = 18 armchair graphene nanoribbons (GNRs). The latter, prepared by a bottom-up solution synthesis, are expected to form solid aggregates which cannot be easily interfaced with metallic electrodes, limiting charge injection at metal-semiconductor interfaces, and are characterized by a finite size, thus by grain boundaries, which negatively affect the charge transport within the film. Both P3HT and GNRs are soluble/dispersible in organic solvents, enabling the use of a single step co-deposition process. The resulting OFETs show a three-fold increase in the charge carrier mobilities in blend films, when compared to pure P3HT devices. This behavior can be ascribed to GNRs, and aggregates thereof, facilitating the transport of the charges within the conduction channel by connecting the domains of the semiconductor film. The electronic characteristics of the devices such as the Ion/Ioff ratio are not affected by the addition of GNRs at different loads. Studies of the electrical characteristics under illumination for potential use of our blend films as organic phototransistors (OPTs) reveal a tunable photoresponse. Therefore, our strategy offers a new method towards the enhancement of the performance of OFETs, and holds potential for technological applications in (opto)electronics.

The low TN : TP ratio, a cause or a result of Microcystis blooms?

An enclosure experiment in the shallow, subtropical Lake Donghu, China, was performed in the summer of 2001 to examine the effect of TN:TP (total phosphorus) ratios and P-reduction on the occurrence of Microcysitis blooms. The treatments were performed with enough amounts of N but with different amounts of P in the water column and sediment. Microcystis blooms occurred in the enclosures either with an initial TN:TP <29 or TN:TP >29 where the nutrients (N, P) were high enough. Microcysitis blooms never occurred in the treatments with low P concentration in spite of the presence of sufficient N. The P-rich sediments served as an important source for the P supply in the water column, and such a process was activated greatly by the outburst of Microcystis blooms which pumped up selectively P from the sediments and thus decreased the TN:TP ratios. Therefore, the low TN:TP ratio is not a cause but rather a result of Microcystis blooms. (C) 2002 Elsevier Science Ltd. All rights reserved.

High-power electroabsorption modulator for radio over fibre system

An electroabsorption modulator using an intra-step quantum well (IQW) active region is fabricated for a radio over fibre system. The strain-compensated InGaAsP/InGaAsP IQW shows good material quality and improved modulation properties, high extinction ratio efficiency (10 dB V-1) and low capacitance (< 0.42 pF), with which high frequency (> 15 GHz) can be obtained. High-speed measurement under high-power excitation shows no power saturation up to an excitation power of 21 dBm. To our knowledge, the input optical power is the highest reported for a multi-quantum well EAM without a heat sink.

Compensation ratio-dependent concentration of a VInH4 complex in n-type liquid encapsulated Czochralski InP

The concentration of hydroen-indium vacancy complex VInH4 in liquid encapsulated Czochralski undoped and Fe-doped n-type InP has been studied by low-temperature infrared absorption spectroscopy. The VInH4 complex is found to be a dominant intrinsic shallow donor defect with concentrations up to similar to 10(16) cm(-3) in as-grown liquid encapsulated Czochralski InP. The concentration of the VInH4 complex is found to increase with the compensation ratio in good agreement with the proposed defect formation model of Walukiewicz [W. Walukiewicz, Phys. Rev. B 37, 4760 (1998); Appl. Phys. Lett. 54, 2094 (1989)], which predicts a Fermi-level-dependent concentration of amphoteric defects. (C) 1998 American Institute of Physics, [S0003-6951(98)04435-0].

Relationship between load/unload response ratio and damage variable and its application

The physics-based parameter: load/unload response ratio (LURR) was proposed to measure the proximity of a strong earthquake, which achieved good results in earthquake prediction. As LURR can be used to describe the damage degree of the focal media qualitatively, there must be a relationship between LURR and damage variable (D) which describes damaged materials quantitatively in damage mechanics. Hence, based on damage mechanics and LURR theory, taking Weibull distribution as the probability distribution function, the relationship between LURR and D is set up and analyzed. This relationship directs LURR applied in damage analysis of materials quantitatively from being qualitative earlier, which not only provides the LURR method with a more solid basis in physics, but may also give a new approach to the damage evaluation of big scale structures and prediction of engineering catastrophic failure. Copyright (c) 2009 John Wiley & Sons, Ltd.

Relationship between load/unload response ratio and damage variable and its application

The physics-based parameter: load/unload response ratio (LURR) was proposed to measure the proximity of a strong earthquake, which achieved good results in earthquake prediction. As LURR can be used to describe the damage degree of the focal media qualitatively, there must be a relationship between LURR and damage variable (D) which describes damaged materials quantitatively in damage mechanics. Hence, based on damage mechanics and LURR theory, taking Weibull distribution as the probability distribution function, the relationship between LURR and D is set up and analyzed. This relationship directs LURR applied in damage analysis of materials quantitatively from being qualitative earlier, which not only provides the LURR method with a more solid basis in physics, but may also give a new approach to the damage evaluation of big scale structures and prediction of engineering catastrophic failure. Copyright (c) 2009 John Wiley & Sons, Ltd.