Elementos de apoio ao dimensionamento de secções compostas em light steel framing

Dissertação de Mestrado, Engenharia Civil, Especialização em Estruturas, Instituto Superior de Engenharia, Universidade do Algarve, 2016

Estudo da resistência ao fogo de pilares de aço inserido em paredes

O comportamento ao fogo de pilares de aço inseridos em paredes de edifícios é substancialmente diferente dos pilares quando isolados. O contacto com as paredes provoca por um lado um efeito de redução das temperaturas, revelando-se de certa forma favorável em termos de comportamento ao fogo, mas por outro lado provocando um aquecimento diferencial das secções levando ao aparecimento de esforços desfavoráveis (momentos fletores) nos pilares, aumentando a instabilidade. Este último fenómeno designa-se de “Thermal Bowing”, provocado pelo aquecimento diferencial, deve ser avaliado por uma quantificação rigorosa das temperaturas nos perfis de aço. O estudo foi realizado em dois níveis, numérico e experimental. Foram testados pilares inseridos em paredes de alvenaria, tanto com a alma paralela como perpendicular à parede. Pretendeu-se assim, avaliar o efeito da ação térmica diferencial no comportamento estrutural dos pilares e concluir qual o efeito das paredes sobre estes na sua resistência estrutural. Foram ainda alvo de análise o nível de carregamento e a esbelteza do pilar. Compararam-se os resultados dos ensaios experimentais com os estudos numéricos, reproduzindo as condições utilizadas nos ensaios experimentais, por forma a contribuir para o desenvolvimento/melhoria dos métodos de dimensionamento dos pilares em situação de incêndio. O programa experimental comportou a realização de ensaios em pilares de aço de secção H, embebidos em paredes. A modelação numérica dos ensaios foi realizada utilizando o programa de computador de elementos finitos ABAQUS, elaborando-se uma análise geométrica e material não - linear. Os principais resultados deste trabalho de investigação foram uma melhor avaliação da evolução de temperaturas na secção transversal dos pilares de aço com aquecimento diferencial, inseridos em paredes, deslocamentos, forças de restrição e esforço axial daí decorrentes. A partir destes resultados, realizou-se uma análise detalhada do deslocamento do centro de gravidade ao longo do tempo, provocada pela degradação das propriedades mecânicas do aço.

Metamorfose planar via métodos Level Set e Particle Level Set para a reconstrução de superfícies tridimensionais

Evolving interfaces were initially focused on solutions to scientific problems in Fluid Dynamics. With the advent of the more robust modeling provided by Level Set method, their original boundaries of applicability were extended. Specifically to the Geometric Modeling area, works published until then, relating Level Set to tridimensional surface reconstruction, centered themselves on reconstruction from a data cloud dispersed in space; the approach based on parallel planar slices transversal to the object to be reconstructed is still incipient. Based on this fact, the present work proposes to analyse the feasibility of Level Set to tridimensional reconstruction, offering a methodology that simultaneously integrates the proved efficient ideas already published about such approximation and the proposals to process the inherent limitations of the method not satisfactorily treated yet, in particular the excessive smoothing of fine characteristics of contours evolving under Level Set. In relation to this, the application of the variant Particle Level Set is suggested as a solution, for its intrinsic proved capability to preserve mass of dynamic fronts. At the end, synthetic and real data sets are used to evaluate the presented tridimensional surface reconstruction methodology qualitatively.

Metamorfose planar via métodos Level Set e Particle Level Set para a reconstrução de superfícies tridimensionais

Evolving interfaces were initially focused on solutions to scientific problems in Fluid Dynamics. With the advent of the more robust modeling provided by Level Set method, their original boundaries of applicability were extended. Specifically to the Geometric Modeling area, works published until then, relating Level Set to tridimensional surface reconstruction, centered themselves on reconstruction from a data cloud dispersed in space; the approach based on parallel planar slices transversal to the object to be reconstructed is still incipient. Based on this fact, the present work proposes to analyse the feasibility of Level Set to tridimensional reconstruction, offering a methodology that simultaneously integrates the proved efficient ideas already published about such approximation and the proposals to process the inherent limitations of the method not satisfactorily treated yet, in particular the excessive smoothing of fine characteristics of contours evolving under Level Set. In relation to this, the application of the variant Particle Level Set is suggested as a solution, for its intrinsic proved capability to preserve mass of dynamic fronts. At the end, synthetic and real data sets are used to evaluate the presented tridimensional surface reconstruction methodology qualitatively.

Politetrafluoroetileno e esclera humana no tratamento cirúrgico de perfuração escleral em coelhos

Purpose: An experimental study to evaluate the behavior of polytetrafluoroethylene (Gore-Tex®) compared with human sclera, in scleral perforations induced in rabbits eyes was performed. Methods: Twenty-two eyes of rabbits were submitted to scleral perforation followed by Gore-Tex® graft in the left eye and human sclera graft in the right eye respectively. During one month the postoperative evolution was analyzed every day: intensity of hyperemia, presence of infection, secretion, rejection and tonicity of the eyes. Results: No cases of secretion, infection or rejection were observed. The histological sections showed fibrosis in the eyes with Gore-Tex®, good adhesion and epithelization. Conclusion: The Gore-Tex® showed to be a plausible material to be used as graft in scleral defects with some advantages such as easy obtention, good handling and durability.

Tratamento da retinopatia diabética: percepções de pacientes em Rio Claro (SP) - Brasil

PURPOSE: To collect information and opinions from a group of diabetic patients regarding diabetic retinopathy and its treatment, in order to get reliable information that can help to improve programs and actions to control and prevent this ocular disease. METHODS: A cross-sectional study was performed. The sample was from 980 diabetic patients seen in a diabetic association. A previous questionnaire was made with general questions about the main subject. Thereafter, an appropriate questionnaire was prepared. RESULTS: The sample showed that among 299 patients with age ranging from 16 to 83 years, with a mean of 57 years, mainly female (67.91%) did not know how severe their disease was (30.8%), or believed that it was not a serious problem (19.7%). The laser technique to solve diabetic retinopathy was known by 60.2% of the patients. It was reported as the only treatment available by 24.1%. Among the reasons for no treatment 59.8% reported that they did not think it was necessary and 29.7% could not afford it. CONCLUSIONS: Patients showed lack of knowledge about how serious is diabetic retinopathy, the possibility of using laser technique for it and the severity of the disease. Some patients believed in the efficacy of the treatment and some patients did not, but all of them reported that they were afraid of submitting to it.

Avaliação dos tipos de glaucoma no serviço de oftalmologia da UNICAMP

PURPOSE: To evaluate the frequency of different types of glaucoma at the Hospital das Clínicas of Campinas State University. METHODS: Cross-sectional study of 329 patients followed at the Glaucoma Service of Campinas State University from October 1 to December 20, 2000. The frequency of each type of glaucoma and the treatment were analyzed. RESULTS: There were 329 patients examined at the Glaucoma Service: 132 (40.1%) were referred to the service as glaucoma suspects and 197 (59.9%) as glaucoma patients. Ninety of the 132 glaucoma suspects had glaucoma (68.2%) and 42 are still under investigation (31.8%). Among the 329 patients, 283 (86%) had glaucoma, 42 (12.8%) were glaucoma suspects, 2 (0.6%) had ocular hypertension and 2 (0.6%) did not have glaucoma. There were 530 eyes with glaucoma: 298 (56.2%) with primary open angle glaucoma, 108 (20.4%) with chronic angle closure glaucoma, 21 (4%) with glaucoma following cataract surgery, 19 (3.6%) congenital glaucoma and 16 (3%) with low-tension glaucoma. All patients received initial clinical treatment with IOP-lowering medication. After a mean follow up of 10.5 months, 89 (16.8%) underwent laser therapy: 72 (13.6%) iridotomy, 7 (1.3%) trabeculoplasty and 10 (1.9%) panphotocoagulation. A hundred and seventy nine (33%) eyes required surgical treatment. CONCLUSION: The most frequent types of glaucoma were primary open angle and angle closure glaucoma. Low tension glaucoma and glaucoma associated with exfoliation syndrome were uncommon in this population.

Proposição, validação e aplicação de um novo metodo para analise cinematica tridimensional da movimentação da caixa toracica durante a respiração

Universidade Estadual de Campinas . Faculdade de Educação Física

Proposta de avaliação da simetria e transferencia de peso e a relação dessa condição com a atividade funcional do hemiplegico

Universidade Estadual de Campinas . Faculdade de Educação Física

Metodologia para analise da movimentação da caixa toracica durante a respiração

Universidade Estadual de Campinas . Faculdade de Educação Física

Dentin permeability of the apical third in different groups of teeth

This ex vivo study evaluated dentin permeability of the root canal in the apical third of different human groups of teeth. Eighty teeth were used, 8 from each dental group: maxillary and mandibular central incisors, lateral incisors and canines, maxillary first premolars (buccal and palatal roots), mandibular first premolars, and maxillary and mandibular second premolars, totalizing 88 roots that were distributed in 11 groups. The root canals were instrumented, irrigated with 1% NaOCl and 15% EDTA. Roots were immersed in 10% copper sulfate for 30 min and then in 1% rubeanic acid alcohol solution for the same period; this chemical reaction reveals dentin permeability by the formation of copper rubeanate, which is a dark-colored compound. Semi-serial 100-µm-thick cross-sections were obtained from the apical third of the roots. Five sections of each apical third were washed, dehydrated, cleared and mounted on glass slides for examination under optical microscopy. The percentage of copper ion infiltration and the amount of tubular dentin were quantified by morphometric analysis. The penetration of copper ions in the apical third ranged from 4.60 to 16.66%. The mandibular central and lateral incisors presented the highest dentin permeability (16.66%), while the maxillary canines and mandibular second and first premolars presented the lowest dentin permeability (4.60%, 4.80% and 5.71%, respectively; p<0.001). The other teeth presented intermediate permeability. In conclusion, dye penetration into dentin tubules at the apical region is strongly dependent on the group of teeth evaluated.

Effectiveness of different final irrigation protocols in removing debris in flattened root canals

This study evaluated in vitro the capacity of debris removal from the apical third of flattened root canals, using different final irrigation protocols. Thirty human mandibular central incisors with a mesiodistal flattened root were prepared using rotary instrumentation by Endo-Flare 25.12 and Hero 642 30.06, 35.02, 40.02 files, irrigated with 2 mL of 1% NaOCl after each file. The specimens were randomly distributed into 5 groups according to the final irrigation of root canals: Group I: 10 mL of distilled water (control), Group II: 10 mL of 1% NaOCl for 8 min, Group III: 2 mL of 1% NaOCl for 2 min (repeated 4 times), Group IV: 10 mL of 2.5% NaOCl for 8 min, and Group V: 10 mL of 2.5% NaOCl for 2 min (repeated 4 times). The apical thirds of the specimens were subjected to histological processing and 6-μm cross-sections were obtained and stained with hematoxylin-eosin. The specimens were examined under optical microscopy at ×40 magnification and the images were subjected to morphometric analysis using the Scion image-analysis software. The total area of root canal and the area with debris were measured in square millimeters. Analysis of variance showed no statistically significant difference (p>0.05) among the groups GI (2.39 ± 3.59), GII (2.91 ± 2.21), GIII (0.73 ± 1.36), GIV (0.95 ± 0.84) and GV (0.51 ± 0.22). In conclusion, the final irrigation protocols evaluated in this study using the Luer syringe presented similar performance in the removal of debris from the apical third of flattened root canals.

Influence of cervical preflaring on determinationof apical file size in mandibular molars: SEM analysis

This study investigated the influence of cervical preflaring with different rotary instruments on determination of the initial apical file (IAF) in mesiobuccal roots of mandibular molars. Fifty human mandibular molars whose mesial roots presented two clearly separated apical foramens (mesiobuccal and mesiolingual) were used. After standard access opening and removal of pulp tissue, the working length (WL) was determined at 1 mm short of the root apex. Five groups (n=10) were formed at random, according to the type of instrument used for cervical preflaring. In group 1, the size of the IAF was determined without preflaring of the cervical and middle root canal thirds. In groups 2 to 5, preflaring was performed with Gates-Glidden drills, ProTaper instruments, EndoFlare instruments and LA Axxes burs, respectively. Canals were sized manually with K-files, starting with size 08 K-files, inserted passively up to the WL. File sizes were increased until a binding sensation was felt at the WL and the size of the file was recorded. The instrument corresponding to the IAF was fixed into the canal at the WL with methylcyanoacrylate. The teeth were then sectioned transversally 1 mm short of the apex, with the IAF in position. Cross-sections of the WL region were examined under scanning electron microscopy and the discrepancies between canal diameter and the diameter of IAF were calculated using the tool "rule" (FEG) of the microscope's proprietary software. The measurements (µm) were analyzed statistically by Kruskal-Wallis and Dunn's tests at 5% significance level. There were statistically significant differences among the groups (p<0.05). The non-flared group had the greatest discrepancy (125.30 ± 51.54) and differed significantly from all flared groups (p<0.05). Cervical preflaring with LA Axxess burs produced the least discrepancies (55.10 ± 48.31), followed by EndoFlare instruments (68.20 ± 42.44), Gattes Glidden drills (68.90 ± 42.46) and ProTaper files (77.40 ± 73.19). However, no significant differences (p>0.05) were found among the rotary instruments. In conclusion, cervical preflaring improved IAF fitting to the canals at the WL in mesiobuccal roots of maxillary first molars. The rotary instruments evaluated in this study did not differ from each other regarding the discrepancies produced between the IAF size and canal diameter at the WL.