热处理对尼龙1010结构影响研究

采用ＷＡＸＤ，ＳＡＸＳ方法研究了热处理对尼龙１０１０聚集态结构的影响．结果表明，在温度为１７５℃左右对样品进行退火处理可获得较完善的结晶．利用Ｗｃ．ｘ~Ｔ关系曲线外推法得到尼龙１０１０样品的Ｔｇ大约为５８℃．根据一维电子密度相关函数法求得了系列样品在所研究条件下的结晶片层厚，过渡层厚，长周期和结晶非晶相间的密度差．得到了不同退火条件尼龙１０１０样品的结晶相密度ρｃ．

THE INFLUENCE OF GAMMA-RADIATION ON POLYAMIDE-1010 AGGREGATE STRUCTURES

The influence of gamma-radiation on polyamide 1010 aggregate structures and crystal damage were examined by using wide angle X-ray diffraction (WAXD) and small angle X-ray scattering (SAXS) techniques. The results revealed that some structural parameters of the aggregated state, the density differences and the degree of crystallinity W-c,W-x, essentially decreased with increasing radiation dose, but the specific surface O-s increased. Crosslinking and scission of irradiated polyamide 1010 samples occurred mainly in amorphous and interphase regions, and crystal damage and amorphization induced by gamma-radiation spread from the interphase and extended into the crystal phase with increasing radiation dose. This result also indicated that the (010) reflection with the hydrogen bond was more susceptible to the action of radiation.

EFFECT OF IRRADIATION ON CRYSTALLINITY AND MECHANICAL-PROPERTIES OF ULTRAHIGH MOLECULAR-WEIGHT POLYETHYLENE

Ultrahigh molecular weight polyethylene (UHMWPE) has been irradiated (0-40 Mrad) with a Co-60 source at room temperature under vacuum. The crystallinity has been investigated by differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS). The mechanical properties have been determined at room temperature. A significant increase of heat of fusion can be seen at low irradiation doses, which is attributed to crystallization, caused by chain scission during the process of irradiation. It is also observed that the thickness of the lamellae changes with irradiation dose. The Young's modulus has been improved significantly after irradiation at low doses. (C) 1993 John Wiley & Sons, Inc.

MOLECULAR CHARACTERISTICS AND CRYSTALLINE-STRUCTURE OF ETHYLENE-DIMETHYLAMINOETHYL-METHACRYLATE COPOLYMERS

The relationship between molecular and crystalline structural characteristics of the ethylene -dimethylaminoethylmethacrylate copolymers (EDAM) was investigated and related to melt flow index MI and average gross content of DAM comonomer, in comparison with low density polyethylene (LDPE) produced by the common high-pressure radical polymerization process. Although the average molecular weight and its distribution are influenced predominantly by the polymerization conditions, DAM-content seems not to depend significantly on molecular weight according to the GPC-FT/IR measurement. Comonomer sequence distributions were determined quantitatively with the C-13-NMR spectra entirely assigned by DEPT and H-1-C-13 COSY techniques. The result suggests the alternating copolymerization tendency and surprisingly coincides with the simulation out-puts based on the assumption of continuous complete mixing reactor model, using Mayo-Lewis equation and the same Q-e values as previously reported on different types of copolymers such as EVA and St.DAM (VA;vinylacetate, St;styrene). It was confirmed by WAXD and SAXS analyses that the crystallinity X(c) and the thickness of lamellar crystal l(c) decreased with increasing DAM-content, whereas the a-lattice and b-lattice dimensions enlarged. X(c) and l(c) can definitely be correlated to the heats of fusion and crystallization measured by DSC. The average size of spherulites measured with light scattering photometry tends to be enlarged with decreasing molecular weight (increasing MI) and DAM-content.

CRYSTAL-STRUCTURE AND THERMODYNAMIC PARAMETERS OF NYLON-1010

WAXD, SAXS, FTIR, DSC and density techniques have been used to investigate the crystal structure, crystal density rho(c), amorphous density rho(a), equilibrium heat of fusion DELTAH(m)degrees and equilibrium melting temperature T(m)degrees. By extrapolating the straight lines in the FTIR absorbance against density plot to zero intensity, rho(c) and rho(a) were estimated to be 1.098 and 1.003 g/cm3 respectively. The rho(c) obtained was too low in value. From X-ray diffraction patterns of uniaxially oriented fibres, the crystal structure of Nylon-1010 was determined. The Nylon-1010 crystallized in the triclinic system, with lattice dimensions: a = 4.9 angstrom, b = 5.4 angstrom, c = 27.8 angstrom, alpha = 49-degrees, beta = 77-degrees, gamma = 63.5-degrees. The unit cell contained one monomeric unit, the space group was P1BAR, and the correct value of rho(c) was 1.135 g/cm3. The degree of crystallinity of the polymer was determined as about 60% (at RT) using Ruland's method. SAXS has been used to investigate the crystalline lamellar thickness, long period, transition zone, the specific inner surface and the electron density difference between the crystalline and amorphous regions for Nylon-1010. The analysis of data was based upon a one-dimensional electron-density correlation function. DELTAH(m)degrees was estimated to be 244.0 J/g by extrapolation of DELTAH(m)degrees in the plot of heat of fusion against specific volume of semicrystalline specimens to the completely crystalline condition (V(sp)c = 1/rho(c)). Owing to the ease of recrystallization of melt-crystallized Nylon-1010 specimens, the well-known Hoffman's T(m)-T(c) method failed in determining T(m)degrees and a Kamide double extrapolation method was adopted. The T(m)degrees value so obtained was 487 K.

STRUCTURE OF MESOMORPHIC FORM OF ISOTACTIC POLYPROPYLENE

The structure of quenched isotactic polypropylene (iPP) films, including samples etched with fuming nitric acid (FNA), has been studied by infrared (IR) spectra, wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), and differential scanning calorimetry (DSC) measurements. The changes of IR, SAXS, DSC, and WAXD results induced by annealing for etched samples have been compared with those for unetched ones. The IR absorbance spectrum of the quenched iPP etched by FNA did not change. In addition, the SAXS intensity did not increase when these samples were annealed, indicating that the total (IR) crystallinity (i.e., the content of chain segments in the helical conformations) of the etched samples does not increase. However, WAXD patterns of the samples changed in a manner similar to those of the unetched one, from the original two blurred diffraction peaks to the sharp crystal patterns of alpha-form iPP, suggesting that the mesomorphic (or liquid crystal-like) phase has reorganized to alpha-form crystals. It is concluded that the change of WAXD of quenched iPP films during annealing results mainly from transformation of order in the mesomorphic phase, rather than only from an increase of crystal size. In other words, mesomorphic-form iPP is not constituted by any known crystals (such as alpha or beta crystals) in small sizes; its WAXD pattern reflects truly the degree of order in the mesomorphic phase.

间苯二甲酸对嵌段共聚酯结构和性能的影响

本文通过X光衍射、DSC、SAXS等方法,考察了间苯二甲酸的含量对聚对苯二甲酸乙二醇-聚己二酸乙二醇多嵌段共聚酯结构和性能的影响,发现合成时间苯二甲酸的加入,使共聚酯的W_(α,x)T_m、I_(?)均下降,同时,力学性能也下降,但间苯二甲酸含量为10％的共聚酯的力学性能最佳。

聚乙烯醇/聚乙烯基吡咯烷酮共混体系的结晶行为

用DSC、WAXD和SAXS研究了聚乙烯醇(PVAl)/聚乙烯基吡咯烷酮(PVP)共混体系的结晶行为.PVAl的结晶度随PVP含量增加而减少,并存在结晶度为零的组成(PVAl)的重量分数约为50％.与纯PVAl相比,共混物的温度区间T_m-T_g减小,表明PVP对PVAl的结晶起抑制作用.共混物中PVAl的结晶速度下降,具体表现为PVAl过冷区随PVP含量增加而扩大,动力学速度常数减小,球晶增长速度下降.纯PVAl和共混体系的等温结晶速率均遵循Avrami方程.退火样品的长周期、片晶厚度和过渡层厚度大于相同组成未退火样品.两者长周期随PVP含量增长加显著增大,片晶厚度增长次之,过渡层厚度变化不大.

聚己内酯和聚氧化乙烯共混体系中的两类片晶相间堆砌

对聚(ε-己内酯)(PCL)/聚氧化乙烯(PEO)共混物的相差显微镜、广角X-射线衍射(WAXD)、小角X-射线散射(SAXS)及示差扫描量热计(DSC)等的研究表明,只有当共混物中PCL(或PEO)的含量低于20％时,两组份是相容的.当PCL含量低于20％时,在共混物中形成了PEO片晶和PCL片晶相间堆砌的结晶形态,当PEO含量不超过20％时,PEO则完全以非晶形式混入PCL的非晶区,同时阻碍了PCL的结晶.可见在结晶过程中,相容的两组份对共混体系形态结构的影响却不尽相同.

PEO/PBHE共混体系X射线散射研究

在聚环氧乙烷(PEO)/聚双酚A羟基醚(PBHE)共混体系中PEO是一个强质子受体,而PBHE是一个强质子给体,两者极易形成氢键,十分有利于形成互容对。笔者研究了PEO/PBHE共混体系的相容性,等温及非等温结晶动力学,本文根据Vonk提出的一维电子密度相关函数,分析了PEO/PBHE的SAXS现象,求得了共混体系的结晶度,片晶层厚度,过渡层厚度及长周期等结构参数。

3,4-聚异戊二烯的磺化反应及其离聚体的结构研究

本工作合成了磺化的3,4-聚异戊二烯及其离子聚合体,IR和NMR谱图证明对3,4-聚异戊二烯的磺化反应是成功的,并且磺酸基团主要与3,4-链节的侧基双键发生反应。WAXD对磺化3,4-聚异戊二烯及其离聚体的研究表明,磺化度的增加使离聚体的结晶能力降低,SAXS结果表明,在离子含量为3.29mol％的离聚体中,未观察到离子簇聚集,只观察到多重离子对的散射。

聚甲基丙烯酸甲酯-聚四氢呋喃嵌段共聚物微观结构的研究

我们用SAXS、TEM等方法研究了分子量分散性较大的PMMA-b-PTHF两嵌段共聚物的微相结构。试样的分子量多分散系数为1.99,PMMA的重量分数为0.48。实验结果表明,其平衡微相结构并不是层状微区,而是在尺寸上也具有一定分散性的球状微区,微区之间并未形成三维有序的大晶格结构,而是一种无规聚集结构。这和单分散两嵌段共聚物理论所预言的结果是不同的。

尼龙-1010结晶结构

用WAXD方法测定了Nylon-1010为三斜晶系结晶结构;α=4.9(?),b=5.4(?),c=27.8(?),α=49°,β=77°,γ=63.5°,每个聚合物单胞含有一个重复单元,空间群为P(?)。模压试样用Ruland方法分析结晶度为60％。以上。电子密度相关函数法分析了SAXS现象,求得了Nylon-1010结晶片层厚度、过渡层厚度、长周期、比内表面及电子密度差。

聚乙烯醇/聚乙烯基吡咯烷酮共混体系相容性研究

用DSC、FTIR、SAXS和测定Flory-Huggins相互作用参数等方法对聚乙二醇(PVA1)/聚乙烯基吡咯烷酮(PVP)共混体系的研究。结果表明,该体系具有完全互容的性质。共混物只有一个玻璃化转变温度。用DMSO作溶剂浇铸的膜光学透明。PVA1的长周期和片晶厚度均随PVP含量增加而增大,但后者增大的幅度比前者小得多,表明PVP和PVA1的非晶部分形成均相并夹入到球晶内部。共混物中PVP羰基吸收峰和PVA1的羟基吸收峰与相应均聚物相比,在红外光谱图中皆向低频方向迁移,迁移波数随第二组分含量的增加而增大。表明二者间有氢键生成。用平衡熔点计算的Flory-Huggins相互作用参数为-0.88。

环氧树脂/聚氧化乙烯共混物及其与硫氰化钠络合物的结构研究(Ⅰ)

对不同分子量聚氧乙烯(PEO)以不同比例与双酚A二缩水甘油醚型环氧树脂(ER)制得的交联共混物ER/PEO,以及再与NaSCN络合后的产物用WAXD,SAXS,DSC和SEM等方法进行了研究,结果表明:随着ER含量的增加,ER/PEO共混物由晶态转为非晶态。ER/PEO属单斜晶系;与NaSCN络合后,体系结晶性变差。ER/PEO-NaSCN属三斜晶系,其长周期比相应ER/PEO交联共混物的长周期值大。EP的加入使非晶层增厚,结晶片层变薄,长周期值增加。