A 5GHz1.8V Low Power CMOS Low-Noise Amplifier

Wireless local-area networks (WLANs) have been deployed as office and home communications infrastructures worldwide. The diversification of the standards, such as IEEE 802.11 series demands the design of RF front-ends. Low power consumption is one of the most important design concerns in the application of those technologies. To maintain competitive hardware costs, CMOS has been used since it is the best solution for low cost and high integration processing, allowing analog circuits to be mixed with digital ones. In the receiver chain, the low noise amplifier (LNA) is one of the most critical blocks in a transceiver design. The sensitivity is mainly determined by the LNA noise figure and gain. It interfaces with the pre-select filter and the mixer. Furthermore, since it is the first gain stage, care must be taken to provide accurate input match, low-noise figure, good linearity and a sufficient gain over a wide band of operation. Several CMOS LNAs have been reported during the last decade, showing that the most research has been done at 802.11/b and GSM standards (900-2400MHz spectrum) and more recently at 802.11/a (5GHz band). One of the more significant disadvantages of 802.11/b is that the frequency band is crowded and subject to interference from other technologies, as is 2.4GHz cordless phones and Bluetooth. As the demand for radio-frequency integrated circuits, operating at higher frequency bands, increases, the IEEE 802.11/a standard becomes a very attractive option to wireless communication system developers. This paper presents the design and implementation of a low power, low noise amplifier aimed at IEEE 802.11a for WLAN applications. It was designed to be integrated with an active balun and mixer, representing the first step toward a fully integrated monolithic WLAN receiver. All the required circuits are integrated at the same die and are powered by 1.8V supply source. Preliminary experimental results (S-parameters) are shown and promise excellent results. The LNA circuit design details are illustrated in Section 2. Spectre simulation results focused at gain, noise figure (NF) and input/output matching are presented in Section 3. Finally, conclusions and comparison with other recently reported LNAs are made in Section 4, followed by future work.

Automatic diagnosis of liver steatosis by ultrasound using autoregressive tissue characterization

Liver steatosis is mainly a textural abnormality of the hepatic parenchyma due to fat accumulation on the hepatic vesicles. Today, the assessment is subjectively performed by visual inspection. Here a classifier based on features extracted from ultrasound (US) images is described for the automatic diagnostic of this phatology. The proposed algorithm estimates the original ultrasound radio-frequency (RF) envelope signal from which the noiseless anatomic information and the textural information encoded in the speckle noise is extracted. The features characterizing the textural information are the coefficients of the first order autoregressive model that describes the speckle field. A binary Bayesian classifier was implemented and the Bayes factor was calculated. The classification has revealed an overall accuracy of 100%. The Bayes factor could be helpful in the graphical display of the quantitative results for diagnosis purposes.

Melhoria da eficiência de amplificadores de potência para sinais RF com envolvente variável

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Electrónica e Telecomunicações

Design and evaluation of multi-band RF energy harvesting circuits and antennas for WSNs

Radio frequency (RF) energy harvesting is an emerging technology that will enable to drive the next generation of wireless sensor networks (WSNs) without the need of using batteries. In this paper, we present RF energy harvesting circuits specifically developed for GSM bands (900/1800) and a wearable dual-band antenna suitable for possible implementation within clothes for body worn applications. Besides, we address the development and experimental characterization of three different prototypes of a five-stage Dickson voltage multiplier (with match impedance circuit) responsible for harvesting the RF energy. Different printed circuit board (PCB) fabrication techniques to produce the prototypes result in different values of conversion efficiency. Therefore, we conclude that if the PCB fabrication is achieved by means of a rigorous control in the photo-positive method and chemical bath procedure applied to the PCB it allows for attaining better values for the conversion efficiency. All three prototypes (1, 2 and 3) can power supply the IRIS sensor node for RF received powers of -4 dBm, -6 dBm and -5 dBm, and conversion efficiencies of 20, 32 and 26%, respectively. © 2014 IEEE.

Automated design of microwave discrete tuning differential capacitance circuits in Si-integrated technologies

A genetic algorithm used to design radio-frequency binary-weighted differential switched capacitor arrays (RFDSCAs) is presented in this article. The algorithm provides a set of circuits all having the same maximum performance. This article also describes the design, implementation, and measurements results of a 0.25 lm BiCMOS 3-bit RFDSCA. The experimental results show that the circuit presents the expected performance up to 40 GHz. The similarity between the evolutionary solutions, circuit simulations, and measured results indicates that the genetic synthesis method is a very useful tool for designing optimum performance RFDSCAs.

Projeto, desenvolvimento e implementação de um robô nadador de inspiração biológica

A elaboração deste trabalho surge no âmbito da unidade curricular de Tese/Dissertação, pertencente ao Mestrado em Engenharia Eletrotécnica e Computadores, ramo de Automação e Sistemas, do Instituto Superior de Engenharia do Porto (ISEP). Este trabalho enquadra-se no âmbito da robótica de inspiração biológica no meio aquático. Pretendeu-se com este trabalho desenvolver e implementar um robô nadador de inspiração biológica. Inicialmente foi realizado um estudo acerca da locomoção dos peixes, para perceber a sua forma de se movimentar. Foi ainda efetuado um estudo acerca dos robôs nadadores existentes, de forma a verificar a sua constituição e formas de locomoção. Numa fase inicial foi desenvolvido um protótipo e, de seguida, procedeu-se à implementação do robô de uma forma sequencial. Implementou-se a estrutura do robô, com o objetivo de se assemelhar o mais possível com um peixe biológico. Foram utilizados servomotores para a locomoção do robô. Para que o robô possua a capacidade de se movimentar numa determinada direção recorreu-se à utilização de uma bússola digital. Posteriormente introduziu-se um emissor/recetor de radiofrequência (RF) para ligar/desligar o robô. Numa fase final procederam-se aos testes da locomoção do robô. Nos ensaios realizados verificou-se que o robô conseguiu nadar com estabilidade e com sentido de direção.

Prototipagem de um sistema de gestão de armazém com recurso à identificação por radiofrequência

A evolução tecnológica atingiu um ritmo que muitas empresas têm dificuldade de acompanhar, existem diversas opções no mercado, para um mesmo objectivo, e tornasse determinante o processo de tomada de decisão sobre qual tecnologia adoptar para determinado objectivo. O alvo de estudo desta dissertação de mestrado, é uma das tecnologias, que últimamente tem ganho especial relevo, quando aplicada ao ambiente industrial, o RFID (Radio Frequency Identification Devices). Na presente dissertação, foi efectuado um levantamento do estado da arte, na área da identificação automática, com especial foco no RFID. Esta revisão bibliográfica teve como principal objectivo perceber quais as tecnologias concorrentes do RFID, e explorar quais as suas principais características tecnológicas e funcionais, bem como as vantagens no uso desta tecnologia de forma a sustentar a implementação de um sistema protótipo de gestão de armazém. O contributo final da dissertação, consiste numa aplicação que tem como principal objectvo simular os fluxos de infomação resultantes dos fluxos fisícos de materiais em ambiente de armazém. Foi também tido em conta no desenvolvimento da aplicação, a demonstração de algumas das mais valias que esta tecnologia pode trazer para a gestão de armazéns. Para implementação da aplicação destaca-se a utilização da arquitectura MVC (Model-view-controlador), em ambiente web, para permitir uma descentalização do software no ambiente indoor do armazém.

Transimpedance amplifier for early detection of breast cancer

Breast cancer is the most common type of cancer worldwide. The effectiveness of its treatment depends on early stage detection, as well as on the accuracy of its diagnosis. Recently, diagnosis techniques have been submitted to relevant breakthroughs with the upcoming of Magnetic Resonance Imaging, Ultrasound Sonograms and Positron Emission Tomography (PET) scans, among others. The work presented here is focused on studying the application of a PET system to a Positron Emission Mammography (PEM) system. A PET/PEM system works under the principle that a scintillating crystal will detect a gamma-ray pulse, originated at the cancerous cells, converting it into a correspondent visible light pulse. The latter must then be converted into an electrical current pulse by means of a Photo- -Sensitive Device (PSD). After the PSD there must be a Transimpedance Amplifier (TIA) in order to convert the current pulse into a suitable output voltage, in a time period lower than 40 ns. In this Thesis, the PSD considered is a Silicon Photo-Multiplier (SiPM). The usage of this recently developed type of PSD is impracticable with the conventional TIA topologies, as it will be proven. Therefore, the usage of the Regulated Common-Gate (RCG) topology will be studied in the design of the amplifier. There will be also presented two RCG variations, comprising a noise response improvement and differential operation of the circuit. The mentioned topology will also be tested in a Radio-Frequency front-end, showing the versatility of the RCG. A study comprising a low-voltage self-biasing feedback TIA will also be shown. The proposed circuits will be simulated with standard CMOS technology (UMC 130 nm), using a 1.2 V power supply. A power consumption of 0.34 mW with a signal-to-noise ratio of 43 dB was achieved.

Non-gyrator type active inductors

Modern CMOS radio frequency (RF) Receivers have enabled efficient and increasing applications. The main requirement is to have system in a single chip, in order to minimize area and cost. For the purpose it is required the development of inductorless circuits for the key blocks of an RF receiver. Examples of this key blocks are RC oscillators, RF band pass filters, and Low Noise Amplifiers. The present dissertation presents an inductorless wideband MOSFET-only RF Non-Gyrator Type of Active Inductors with low area, low cost, and very low power, capable of covering the whole WMTS, and ISM, band and intended for biomedical applications. The proposed circuit is based on a floating capacitor connected between two controlled current sources. The first current source, which is controlled by the circuit input voltage, has two objectives: supply current to the capacitor (

Quadrature generators based on ring oscillators and shift registers

Quadrature oscillators are key elements in modern radio frequency (RF) transceivers and very useful nowadays in wireless communications, since they can provide: low quadrature error, low phase-noise, and wide tuning range (useful to cover several bands). RC oscillators can be fully integrated without the need of external components (external high Q-inductors), optimizing area, cost, and power consumption. The conventional structure of ring oscillator offers poor frequency stability and phasenoise, low quality factor (Q), and besides being vulnerable to process, voltage and temperature (PVT) variations, its performance degrades as the frequency of operation increases. This thesis is devoted to quadrature oscillators and presents a detailed comparative study of ring oscillator and shift register (SR) approaches. It is shown that in SRs both phase-noise and phase error are reduced, while ring oscillators have the advantage of occupying less area and less consumption due to the reduced number of components in the circuit. Thus, although ring oscillators are more suitable for biomedical applications, SRs are more appropriate for wireless applications, especially when specification requirements are more stringent and demanding. The first architecture studied consists in a simple CMOS ring oscillator employing an odd number of static single-ended inverters as delay cells. Subsequently, the quadrature 4-stage ring oscillator concept is shown and post-layout simulations are presented. The 3 and 4-phase single-frequency local oscillator (LO) generators employing SRs are presented, the latter with 50% and 25% duty-cycles. The circuits operate at 600 MHz and 900 MHz, and were designed in a 130 nm standard CMOS technology with a voltage supply of 1.2 V.

Advances and future challenges in printed batteries

There is an increasing interest in thin and flexible energy storage devices to meet modern society needs for applications such as, radio frequency sensing, interactive packaging and other consumer products. Printed batteries comply these requirements and are an excellent alternative to conventional batteries for many applications. Flexible and micro-batteries are also included in the area of printed batteries whenever fabricated by printing technologies. The main characteristics, advantages, disadvantages, developments, and printing techniques of printed batteries are presented and discussed in this review. The state-of-art takes into account both the research and industrial levels. In the academic one, the research progress of printed batteries is summarized divided in lithium-ion battery (Li-ion), zinc-manganese dioxide (Zn-MnO2), and other battery types with emphasis on the different materials for anode, cathode and separator as well as in the battery design. With respect to the industrial state-of-art, materials, device formulations and manufacturing techniques are presented. Finally, the prospects and challenges of printed batteries are discussed.

Energy harvesting device based on a metallic glass/PVDF magnetoelectric laminated composite

A flexible and low cost energy harvester device based on the magnetoelectric (ME) effect has been designed using Fe64Co17Si7B12 as amorphous magnetostrictive ribbons and PVDF as the piezoelectric element. Sandwich-type laminated composite of 3 cm long has been fabricated by gluing these ribbons to the PVDF with the Devcon 5 minute epoxy. Good power output and power density of 6.4 μW and 1.5 mW/cm3, respectively, have been obtained through a multiplier circuit. All values have been measured at the magnetomechanical resonance of the laminate. The effect of the length of the ME laminate on the power output has been also studied, exhibiting a decay as the length of the ME laminate does. Nevertheless, good performance of such device has been obtained for a 0.5 cm long device, working already at 337 KHz, within the low radio frequency (LRF) range.

Desenvolvimento e caracterização de díodos orgânicos emissores de luz

Dissertação de mestrado integrado em Engenharia Eletrónica Industrial e Computadores

Novas funcionalidades para dispositivos médicos invasivos com imagem

Tese de Doutoramento em Engenharia Eletrónica e de Computadores.

Children's play and leisure : connections with emotional competence

O jogo e o lazer são elementos importantes para o desenvolvimento das crianças. O objetivo geral desta tese foi o de investigar o modo como o jogo e o lazer estão relacionados com diferentes aspetos das competências emocional e social das crianças e jovens. Nesta tese foram investigados três aspetos do jogo: o tempo, a forma e o nível social, diferentes formas de lazer, e vários elementos chave do funcionamento sócio-emocional, através da combinação de observações naturalistas, tarefas, questionários e de um método inovador de mensuração, baseado em Identificação por Rádio-Frequência. O panorama que surge dos estudos incluídos nesta tese é que o jogo e o lazer estão relacionados com o funcionamento sócio-emocional, embora de formas distintas, e por vezes inesperadas. Os estudos no recreio revelaram que as crianças envolvem-se predominantemente no jogo de atividade física. Contudo, enquanto que uma forma de jogo de atividade física, o jogo de exercício, foi associado a melhor competência social, a outra forma, o jogo de luta-e-perseguição, foi associado à agressividade. O facto de o jogo de faz-de-conta, em estudos anteriores, ter sido maioritariamente estudado em espaços interiores, pode explicar o porquê das associações negativas encontradas entre o jogo de faz-de-conta, quer em grupo, quer solitário (nas raparigas) e a competência sócio-emocional, que contrastam com a literatura. De facto, as crianças que não conseguem juntar-se aos seus pares no jogo de exercício podem optar por esta alternativa, o que sugere que crianças socialmente competentes poderão retirar maior vantagem das oportunidades existentes, adaptando melhor os seus comportamentos de jogo. As crianças mais velhas têm geralmente mais liberdade de decisão sobre o seu tempo de lazer. Quando perguntámos às crianças mais velhas e aos adolescentes como passavam a sua semana, as atividades de ecrã destacaram-se. Contudo, as atividades de ecrã e as atividades intelectuais foram relacionadas a mais problemas de saúde mental, enquanto que as atividades desportivas foram associadas a melhor saúde mental. Concluindo, diferentes formas de jogo e de lazer podem ter diferentes funções, de uma forma positiva ou negativa, dependendo da situação em que a criança se encontra.