Preferential CO oxidation over a copper-cerium oxide catalyst in a microchannel reactor

The activity of a 5-wt% Cu/CeO2-x catalyst during preferential CO oxidation in hydrogen-rich gas mixtures was studied in a microchannel reactor. The CO concentration dropped from 1 vol.% to 10 ppm at a selectivity of 60%, at a temperature of 190 degrees C, and a weight hour space velocity (WHSV) of 55,000 cm(3) g(-1) h(-1). Both the CO concentration and the temperature increased when the WHSV was increased from 50,000 to 500,000 cm(3) g(-1) h(-1). An increase of the O-2 concentration from a 1.2 to 3 fold excess reduced the CO concentration to 10 ppm in a broad temperature interval of 50 degrees C at WHSVs up to 275,000 cm(3) g(-1) h(-1). The preferential CO oxidation could be carried out at higher flow rates and at higher selectivities in the microchannel reactor compared to a fixed-bed flow reactor. (C) 2008 Elsevier B.V. All rights reserved.

Chemical control through dissociative electron attachment - A study on pentafluorotoluene, pentafluoroaniline and pentafluorophenol

In a combined experimental and theoretical study on dissociative electron attachment (DEA) to pentafluorotoluene, pentafluoroaniline and pentafluorophenol in the energy range 0-3 eV we reveal the role of rearrangement and hydrogen bonded intermediates in the DEA process and show that HF formation can be used to enable otherwise inaccessible, efficient low energy DEA processes.

Dissociative electron attachment to C2F5 radicals

Dissociative electron attachment to the reactive C2F5 molecular radical has been investigated with two complimentary experimental methods; a single collision beam experiment and a new flowing afterglow Langmuir probe technique. The beam results show that F- is formed close to zero electron energy in dissociative electron attachment to C2F5. The afterglow measurements also show that F- is formed in collisions between electrons and C2F5 molecules with rate constants of 3.7 × 10-9 cm3 s-1 to 4.7 × 10-9 cm3 s-1 at temperatures of 300–600 K. The rate constant increases slowly with increasing temperature, but the rise observed is smaller than the experimental uncertainty of 35%.

Prey field switching based on preferential behaviour can induce Lévy flights

Using the foraging movements of an insectivorous bat, Myotis mystacinus, we describe temporal switching of foraging behaviour in response to resource availability. These observations conform to predictions of optimized search under the Lévy flight paradigm. However, we suggest that this occurs as a result of a preference behaviour and knowledge of resource distribution. Preferential behaviour and knowledge of a familiar area generate distinct movement patterns as resource availability changes on short temporal scales. The behavioural response of predators to changes in prey fields can elicit different functional responses, which are considered to be central in the development of stable predator-prey communities. Recognizing how the foraging movements of an animal relate to environmental conditions also elucidates the evolution of optimized search and the prevalence of discrete strategies in natural systems. Applying techniques that use changes in the frequency distribution of movements facilitates exploration of the processes that underpin behavioural changes. © 2012 The Author(s) Published by the Royal Society. All rights reserved.

Maternal Religiosity, Family Resources and Stressors, and Parent-Child Attachment Security in Northern Ireland

This study explores the associations between mothers' religiosity, and families' and children's functioning in a stratified random sample of 695 Catholic and Protestant motherchild dyads in socially deprived areas in Belfast, Northern Ireland, a region which has experienced centuries of sectarian conflict between Protestant Unionists and Catholics Nationalists. Findings based on mother and child surveys indicated that even in this context of historical political violence associated with religious affiliation, mothers' religiosity played a consistently positive role, including associations with multiple indicators of better family functioning (i.e., more cohesion and behavioral control and less conflict, psychological distress, and adjustment problems) and greater parentchild attachment security. Mothers' religiosity also moderated the association between parentchild attachment security and family resources and family stressors, enhancing positive effects of cohesion and mother behavioral control on motherchild attachment security, and providing protection against risks associated with mothers' psychological distress. Findings are discussed in terms of implications for understanding the role of religiosity in serving as a protective or risk factor for children and families.

The impact of hyperemesis gravidarum on maternal mental health and maternal-fetal attachment

In addition to physical health risks, it has been postulated that hyperemesis gravidarum (HG) - severe and persistent nausea and vomiting during pregnancy - can adversely affect maternal mental health and maternal-fetal attachment.

Evaluation of a Final Year Work-shadowing Attachment

The transition from medical student to junior doctor is well recognised to be a difficult and stressful period. To ease this transition, most UK universities have a work-shadowing period (WSP), during which students can learn practical skills needed for forthcoming employment. The aim of this study was to evaluate the WSP at Queen's University Belfast, and gain the views of both students and Foundation Programme Supervisors and Directors (FPSDs). The study utilised both qualitative (focus groups) and quantitative (questionnaires) approaches. The FPSDs completed a specific questionnaire designed for this study, while the students completed the university's internal quality assurance questionnaire. Twenty-eight of the 37 (76%) FPSDs and 106 / 196 (54%) students completed the questionnaires. Focus groups were conducted with up to 10 students in each group in both a regional centre and a district general hospital at the start and the end of the WSP as well as 8 weeks into working life. The transcripts of the focus groups were analysed and themes identified. A number of deficiencies with the current WSP were identified, including concerns about the use of log books, the timing of the attachment and relatively low levels of supervision provided by senior hospital staff members. As a result, students felt unprepared for commencing work, with particular mention given to medical emergencies, prescribing, and the emotional aspects of the job. A number of recommendations are made, including the need for more senior input to ensure better student attendance, participation and clinical interaction. Furthermore, students should be offered additional supervised responsibility for delivery of patient care and more experiential learning with respect to drug prescribing and administration. The study also suggests that more needs to be done to help ease the emotional and psychological stresses of the early FY1 period. These issues have been resolved to a large extent with the introduction of the new final year Student Assistantship module in the academic year 2010-2011. © The Ulster Medical Society, 2012.

Molecular rearrangement reactions in the gas phase triggered by electron attachment

Bond formation and rearrangement reactions in gas phase electron attachment were studied through dissociative electron attachment (DEA) to pentafluorotoluene (PFT), pentafluoroaniline (PFA) and pentafluorophenol (PFP) in the energy range 0-14 eV. In the case of PFA and PFP, the dominant processes involve formation of [M - HF](-) through the loss of neutral HF. This fragmentation channel is most efficient at low incident electron energy and for PFP it is accompanied by a substantial conformational change of the anionic fragment. At higher energy, HF loss is also observed as well as a number of other fragmentation processes. Thermochemical threshold energies have been computed for all the observed fragments and classical trajectories of the electron attachment process were calculated to elucidate the fragmentation mechanisms. For the dominant reaction channel leading to the loss of HF from PFP, the minimum energy path was calculated using the nudged elastic band method.

Effect of laser treatment on the attachment and viability of mesenchymal stem cell responses on shape memory NiTi alloy

The objectives of this study were to investigate the effect of laser-induced surface features on the morphology, attachment and viability of mesenchymal stem cells (MSCs) at different periods of time, and to evaluate the biocompatibility of different zones: laser-melted zone (MZ), heat-affected zone (HAZ) and base metal (BM) in laser-treated NiTi alloy. The surface morphology and composition were studied by scanning electron microscope (SEM) and X-ray photoemission spectroscopy (XPS), respectively. The cell morphology was examined by SEM while the cell counting and viability measurements were done by haemocytometer and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) colorimetric assay. The results indicated that the laser-induced surface features, such as surface roughening, presence of anisotropic dendritic pattern and complete surface Ni oxidation were beneficial to improve the biocompatibility of NiTi as evidenced by the highest cell attachment (4 days of culture) and viability (7 days of culture) found in the MZ. The biocompatibility of the MZ was the best, followed by the BM with the HAZ being the worst. The defective and porous oxide layer as well as the coarse grained structure might attribute to the inferior cell attachment (4 days of culture) and viability (7 days of culture) on the HAZ compared with the BM which has similar surface morphology.

Banking compliance and dependence corruption: towards an attachment perspective

Why did banking compliance fail so badly in the recent financial crisis and why, according to many, does it continue to do so? Rather than point to the lack of oversight of individuals in bank compliance roles, as many commentators do, in this paper I examine in depth the organizational context that surrounded people in such roles. I focus on those compliance personnel who did speak out about risky practices in their banks, who were forced to escalate the problem and 'whistle-blow' to external parties, and who were punished for doing so. Drawing on recent empirical data from a wider study, I argue that the concept of dependence corruption is useful in this setting, and that it can be extended to encompass interpersonal attachments. This, in turn, problematises the concept of dependence corruption because interpersonal attachments in organisational settings are inevitable. The paper engages with recent debates on whether institutional corruption is an appropriate lens for studying private-sector organisations by arguing for a focus on roles, rather than remaining at the level of institutional fields or individual organisations. Finally, the paper contributes to studies on banking compliance in the context of the recent crisis; without a deeper understanding of those who were forced to extremes to simply do their jobs, reform of the banking sector will prove difficult.

Green Space Attachment and Health: A Comparative Study in Two Urban Neighborhoods

The positive relationships between urban green space and health have been well documented. Little is known, however, about the role of residents’ emotional attachment to local green spaces in these relationships, and how attachment to green spaces and health may be promoted by the availability of accessible and usable green spaces. The present research aimed to examine the links between self-reported health, attachment to green space, and the availability of accessible and usable green spaces. Data were collected via paper-mailed surveys in two neighborhoods (n = 223) of a medium-sized Dutch city in the Netherlands. These neighborhoods differ in the perceived and objectively measured accessibility and usability of green spaces, but are matched in the physically available amount of urban green space, as well as in demographic and socio-economic status, and housing conditions. Four dimensions of green space attachment were identified through confirmatory factor analysis: place dependence, affective attachment, place identity and social bonding. The results show greater attachment to local green space and better self-reported mental health in the neighborhood with higher availability of accessible and usable green spaces. The two neighborhoods did not differ, however, in physical and general health. Structural Equation Modelling confirmed the neighborhood differences in green space attachment and mental health, and also revealed a positive path from green space attachment to mental health. These findings convey the message that we should make green places, instead of green spaces.

The effect of preferential paw usage on dogs' (Canis familiaris) performance in a manipulative problem-solving task

In a number of species, individuals showing lateralized hand/paw usage (i.e. the preferential use of either the right or left paw) compared to ambilateral individuals have been shown to be more proactive in novel situations. In the current study we used an established test to assess preferential paw usage in dogs (the Kong test) and then compared the performance of ambilateral and lateralized dogs as well as left- vs. right-pawed dogs in a novel manipulative problem solving task. Results showed an equal proportion of ambilateral and lateralized dogs but contrary to predictions non-lateralized dogs were faster at accessing the apparatus in test trials. No differences emerged between right- and left-pawed dogs. Results are discussed in relation to previous studies on lateralization. © 2013 Elsevier B.V.

Effects of tobacco products on the attachment and growth of periodontal ligament fibroblasts

BACKGROUND: Cigarette smoking is one of the most significant risk factors in the development and further advancement of inflammatory periodontal disease, however, the role of either nicotine or its primary metabolite cotinine in the progression of periodontitis is unclear. This study aimed to investigate the effects of nicotine and cotinine on the attachment and growth of fibroblasts derived from human periodontal ligament (PDL).

METHODS: Primary cultures were prepared from the roots of extracted premolar teeth. Cells were used at both low (P3 to P5) and high (P11 to P13) passage. Cell numbers were determined over 14 days using either the 3-(4,5-dimethylthiazol-2-yl)-2, 5-diphenyl tetrazolium bromide (MTT) assay or with a Coulter counter. Cultures were exposed to culture medium supplemented with 1) 15% fetal calf serum (FCS) only; 2) 1% FCS only; 3) 1% FCS and nicotine (concentration range 5 ng/ml to 10 mg/ml); or 4) 1% FCS and cotinine (concentration range 0.5 ng/ml to 10 microg/ml).

RESULTS: Nicotine significantly (P <0.05, by ANOVA) inhibits attachment and growth of low passage cells at concentrations >1 mg/ml and high passage PDL fibroblasts at concentrations >0.5 mg/ml. Cotinine, at the highest concentration used (10 microg/ml), appeared to inhibit attachment and growth of both low and high passage fibroblasts but this was not statistically significant (P >0.05, by ANOVA).

CONCLUSIONS: Tobacco products inhibit attachment and growth of human PDL fibroblasts. This may partly explain the role of these substances in the progression of periodontitis.

Bottom up strategies for the morphology control of BaTiO3 particulates

As propriedades funcionais dos materiais ferroeléctricos tais como a polarização reversível, piroelectricidade, piezoelectricidade, elevada actividade óptica não linear e comportamento dieléctrico não linear são fundamentais para a sua aplicação em sensores, microactuadores, detectores de infravermelhos, filtros de fase de microondas e memórias não-voláteis. Nos últimos anos, motivado pelas necessidades industriais de redução do tamanho dos dispositivos microelectrónicos, aumentando a eficiência volumétrica, tem sido feito um grande esforço ao nível da investigação para desenvolver estruturas ferroeléctricas à escala micro- e nano- métrica. É sabido que a redução de tamanho em materiais ferroeléctricos afecta significamente as suas propriedades. Neste sentido e considerando que foi previsto teoreticamente por cálculos ab initio que estruturas do tipo nanocilindros e nanodiscos apresentariam um novo tipo de ordem ferroeléctrica e, na expectativa de alcançar conhecimento para o desenvolvimento de uma nova geração de dispositivos microelectróncos, existe um grande interesse em desenvolver métodos de fabrico de nanoestruturas ferroeléctricas unidimensionais (1D) tais como nanocilindros e nanotubos. As estratégias de fabrico de nanoestruturas 1D até agora descritas na literatura indicam claramente as dificuldades inerentes à sua preparação. Existem duas grandes vias de síntese destas nanoestruturas: i) o método “topdown” que consiste na redução de tamanho de um dado material até à obtenção duma estrutura 1D; e ii) o método “bottom-up” em que átomos, iões e moléculas são agrupados para formar um material 1D. O método “top down” envolve em geral técnicas de desgaste, como o uso do feixe de electrões, que apesar de permitirem elevada precisão no posicionamento e no controlo do tamanho, falham em termos de resolução, exigem muito tempo e causam facilmente defeitos que deterioram as propriedades físicas destes materiais. Na metodologia “bottom up” a utilização de moléculas ou estruturas “molde” tem sido a mais explorada. As estructuras 1D podem também ser preparadas sem recorrer a “moldes”. Neste caso a agregação orientada é promovida pelo recurso a aditivos que controlam o crescimento dos cristais em direcções preferenciais. Neste contexto, neste trabalho utilizaram-se duas estratégias “bottom up” de baixo custo para a preparação de nanopartículas de titanato de bário (BaTiO3) com morfologia controlada: 1) síntese química (em solução e em fase vapor) com utilização de nanotubos de titanato TiNTs) como “moldes” e precursores de titânio 2) síntese química em solução com presença de aditivos. Os nanotubos de titanato de sódio foram preparados por síntese hidrotermal. Como existiam muitas dúvidas acerca da natureza estrutural e do mecanismo de formação dos NTs, a parte inicial do trabalho foi dedicada à realização de um estudo sistemático dos parâmetros intervenientes na síntese e à caracterização da sua estrutura e microestrutura. Foi demonstrado que os NTs têm a fórmula geral A2Ti2O5 (A = H+ or Na+), e não TiO2 (anátase) com defendido por vários autores na literatura, e podem ser preparados por método hidrotermal em meio fortemente alcalino usando como fonte de titânio TiO2 comercial na forma de anátase ou rútilo. A menor reactividade do rútilo exige temperaturas de síntese superiores ou tempos de reacção mais longos. A forma tubular resulta do tratamento hidrotermal e não de processos de lavagem e neutralização subsequentes. Se os NTs forem tratados após a síntese hidrotérmica em água a 200 ºC, transformam-se em nanocilindros. Uma das partes principais desta tese consistiu na investigação do papel dos NTs de titanato no crescimento anisotrópico de BaTiO3. O potencial funcionamento dos NTs como “moldes” para além de precursores foi testado em reacção com hidróxido de bário em síntese em solução e por reacção com um precursor orgânico de bário em fase vapor. Tendo por base os estudos cinéticos realizados, bem como as alterações estruturais e morfológicas das amostras, é possível concluir que a formação do BaTiO3 a partir de NTs de titanato de sódio, ocorre por dois mecanismos dependendo da temperatura e tempo de reacção. Assim, a baixa temperatura e curto tempo de reacção verifica-se que se formam partículas dendríticas de BaTiO3 cuja superfície é bastante irregular (“wild”) e que apresentam estrutura pseudo-cúbica. Estas partículas formam-se por reacção topotáctica na fronteira dos nanotubos de titanato de sódio. A temperaturas mais altas e/ou reacções mais longas, a reacção é controlada por um mecanismo de dissolução e precipitação com formação de dendrites de BaTiO3 tetragonais com superfície mais regular (“seaweed”). A microscopia de força piezoeléctrica mostrou que as dendrites “seaweeds“ possuem actividade piezoeléctrica superior à das dendrites “wild”, o que confirma o papel desempenhado pela estrutura e pela concentração de defeitos na rede na coerência e ordem ferroeléctrica de nanoestruturas. Os nossos resultados confirmam que os NTs de titanato não actuam facilmente como “moldes” na síntese em solução de BaTiO3 já que a velocidade de dissolução dos NTs em condições alcalinas é superior à velocidade de formação do BaTiO3. Assumindo que a velocidade de reacção dos NTs com o precursor de bário é superior em fase vapor, efectuou-se a deposição de um precursor orgânico de bário por deposição química de vapor sobre um filme de NTs de titnato de sódio depositados por deposição electroforética. Estudou-se a estabilidade dos NTs nas diferentes condições do reactor. Quando os NTs são tratados a temperaturas superiores a 700 ºC, ocorre a transformação dos NTs em nanocilindros de anatase por um mecanismo de agregação orientada. Quando se faz a deposição do precursor de bário, seguida de calcinação a 700 ºC em atmosfera oxidante de O2, verifica-se que a superficie dos NTs fica coberta com nanocristais de BaTiO3 independentemente da concentração de bário. O papel dos NTs de titanato no crescimento anisotrópico de BaTiO3 em fase vapor é assim descrito pela primeira vez. Em relação à metodologias de crescimento de partículas na ausência de “moldes” mas com aditivos fez-se um estudo sistemático utilizando 5 aditivos de natureza differente. As diferenças entre aditivos foram sistematizadas tendo em conta as diferenças estruturais e morfológicas verificadas. Está provado que os aditivos podem funcionar como modificadores de crescimento cristalino por alteração do seu padrão de crescimento ou por alteração da cinética de crescimento das faces cristalográficas do cristal. Entre os aditivos testados verificou-se que o ácido poliacrilíco adsorve em faces específicas do BaTiO3 alterando a cinética de crescimento e induzindo a agregação orientada das partículas. O polivinilpirrolidona, o docecilsulfato de sódio e hidroxipropilmetilcelulose actuam mais como inibidores de crescimento do que como modificadores do tipo de crescimento. A D-frutose aumenta a energia de activação da etapa de nucleação não ocorrendo formação de BaTiO3 para as mesmas condições dos outros aditivos. Esta tese clarifica o papel dos NTs de titanato de sódio enquanto precursores e “moldes” no crescimento anisotrópico de BaTiO3 em solução e em fase vapor. É feita também a abordagem do controlo morfológico do BaTiO3 através do uso de aditivos. As estratégias de preparação de BaTiO3 propostas são de baixo custo, reprodutíveis e fáceis de efectuar. Os resultados contribuem para uma melhor compreensão da relação tamanho – morfologia – propriedade em materiais ferroeléctricos nanométricos com vista à sua potencial aplicação.