Effect of zirconia surface treatments on the shear strength of zirconia/veneering ceramic composites

Aim of the investigation was to assess the effect of different surface treatments on the bond strength of veneering ceramics to zirconia. In a shear test, the influences of polishing, sandblasting, and silica-coating of the zirconia surface on bonding were assessed with five different veneering ceramics. In addition the effect of liner application was examined. With one veneering ceramic, the impact of regeneration firing of zirconia was also evaluated. Statistical analysis was performed with one-way ANOVA and post hoc Scheffé's test. Failure in every case occurred in the veneering ceramic adjacent to the interface with a thin layer of ceramic remaining on the zirconia surface, indicating that bond strength was higher than the cohesive strength of the veneering ceramic. Shear strength ranged from 23.5 +/- 3.4 MPa to 33.0 +/- 6.8 MPa without explicit correlation to the respective surface treatment. Regeneration firing significantly decreased the shear strength of both polished and sandblasted surfaces. Findings of this study revealed that bonding between veneering ceramics and zirconia might be based on chemical bonds. On this note, sandblasting was not a necessary surface pretreatment to enhance bond strength and that regeneration firing was not recommended.

Surface InGaAs nanostructures for sensing applications

El desarrollo de sensores está ganando cada vez mayor importancia debido a la concienciación ciudadana sobre el medio ambiente haciendo que su desarrollo sea muy elevado en todas las disciplinas, entre las que cabe destacar, la medicina, la biología y la química. A pesar de la existencia de estos dispositivos, este área está aún por mejorar, ya que muchos de los materiales propuestos hasta el momento e incluso los ya comercializados muestran importantes carencias de funcionamiento, eficiencia e integrabilidad entre otros. Para la mejora de estos dispositivos, se han propuesto diversas aproximaciones basadas en nanosistemas. Quizá, uno de las más prometedoras son las nanoestructuras de punto cuántico, y en particular los semiconductores III-V basados en la consolidada tecnología de los arseniuros, las cuáles ofrecen excelentes propiedades para su uso como sensores. Además, estudios recientes demuestran su gran carácter sensitivo al medio ambiente, la posibilidad de funcionalizar la superficie para la fabricación de sensores interdisciplinares y posibilididad de mejorar notablemente su eficiencia. A lo largo de esta tesis, nos centramos en la investigación de SQD de In0.5Ga0.5As sobre substratos de GaAs(001) para el desarrollo de sensores de humedad. La tesis abarca desde el diseño, crecimiento y caracterización de las muestras hasta la el posterior procesado y caracterización de los dispositivos finales. La optimización de los parámetros de crecimiento es fundamental para conseguir una nanoestructura con las propiedades operacionales idóneas para un fin determinado. Como es bien sabido en la literatura, los parámetros de crecimiento (temperatura de crecimiento, relación de flujos del elemento del grupo V y del grupo I II (V/III), velocidad de crecimiento y tratamiento térmico después de la formación de la capa activa) afectan directamente a las propiedades estructurales, y por tanto, operacionales de los puntos cuánticos (QD). En esta tesis, se realiza un estudio de las condiciones de crecimiento para el uso de In0.5Ga0.5As SQDs como sensores. Para los parámetros relacionados con la temperatura de crecimiento de los QDs y la relación de flujos V / I I I se utilizan los estudios previamente realizados por el grupo. Mientras que este estudio se centrará en la importancia de la velocidad de crecimiento y en el tratamiento térmico justo después de la nucleación de los QDs. Para ello, se establece la temperatura de creciemiento de los QDs en 430°C y la relación de flujos V/III en 20. Como resultado, los valores más adecuados que se obtienen para la velocidad de crecimiento y el tratamiento térmico posterior a la formación de los puntos son, respectivamente, 0.07ML/s y la realización de una bajada y subida brusca de la temperatura del substrato de 100°C con respecto a la temperatura de crecimiento de los QDs. El crecimiento a una velocidad lo suficientemente alta que permita la migración de los átomos por la superficie, pero a su vez lo suficientemente baja para que se lleve a cabo la nucleación de los QDs; en combinación con el tratamiento brusco de temperatura que hace que se conserve la forma y composición de los QDs, da lugar a unos SQDs con un alto grado de homogeneidad y alta densidad superficial. Además, la caracterización posterior indica que estas nanoestructuras de gran calidad cristalina presentan unas propiedades ópticas excelentes incluso a temperatura ambiente. Una de las características por la cual los SQD de Ino.5Gao.5As se consideran candidatos prometedores para el desarrollo de sensores es el papel decisivo que juega la superficie por el mero hecho de estar en contacto directo con las partículas del ambiente y, por tanto, por ser capaces de interactuar con sus moléculas. Así pues, con el fin de demostrar la idoneidad de este sistema para dicha finalidad, se evalúa el impacto ambiental en las propiedades ópticas y eléctricas de las muestras. En un primer lugar, se analiza el efecto que tiene el medio en las propiedades ópticas. Para dicha evaluación se compara la variación de las propiedades de emisión de una capa de puntos enterrada y una superficial en distintas condiciones externas. El resultado que se obtiene es muy claro, los puntos enterrados no experimentan un cambio óptico apreciable cuando se varían las condiciones del entorno; mientras que, la emisión de los SQDs se modifica significativamente con las condiciones del medio. Por una parte, la intensidad de emisión de los puntos superficiales desaparece en condiciones de vacío y decrece notablemente en atmósferas secas de gases puros (N2, O2). Por otra parte, la fotoluminiscencia se conserva en ambientes húmedos. Adicionalmente, se observa que la anchura a media altura y la longitud de onda de emisión no se ven afectadas por los cambios en el medio, lo que indica, que las propiedades estructurales de los puntos se conservan al variar la atmósfera. Estos resultados apuntan directamente a los procesos que tienen lugar en la superficie entre estados confinados y superficiales como responsables principales de este comportamiento. Así mismo, se ha llevado a cabo un análisis más detallado de la influencia de la calidad y composición de la atmósfera en las propiedades ópticas de los puntos cuánticos superficiales. Para ello, se utilizan distintas sustancias con diferente polaridad, composición atómica y masa molecular. Como resultado se observa que las moléculas de menor polaridad y más pesadas causan una mayor variación en la intensidad de emisión. Además, se demuestra que el oxígeno juega un papel decisivo en las propiedades ópticas. En presencia de moléculas que contienen oxígeno, la intensidad de fotoluminiscencia disminuye menos que en atmósferas constituidas por especies que no contienen oxígeno. Las emisión que se observa respecto a la señal en aire es del 90% y del 77%, respectivamente, en atmósferas con presencia o ausencia de moléculas de oxígeno. El deterioro de la señal de emisión se atribuye a la presencia de defectos, enlaces insaturados y, en general, estados localizados en la superficie. Estos estados actúan como centros de recombinación no radiativa y, consecuentemente, se produce un empeoramiento de las propiedades ópticas de los SQDs. Por tanto, la eliminación o reducción de la densidad de estos estados superficiales haría posible una mejora de la intensidad de emisión. De estos experimentos de fotoluminiscencia, se deduce que las interacciones entre las moléculas presentes en la atmósfera y la superficie de la muestra modifican la superficie. Esta alteración superficial se traduce en un cambio significativo en las propiedades de emisión. Este comportamiento se atribuye a la posible adsorción de moléculas sobre la superficie pasivando los centros no radiativos, y como consecuencia, mejorando las propiedades ópticas. Además, los resultados demuestran que las moléculas que contienen oxígeno con mayor polaridad y más ligeras son adsorbidas con mayor facilidad, lo que hace que la intensidad óptica sufra variaciones despreciables con respecto a la emisión en aire. Con el fin de desarrollar sensores, las muestras se procesan y los dispositivos se caracterizan eléctricamente. El procesado consiste en dos contactos cuadrados de una aleación de Ti/Au. Durante el procesado, lo más importante a tener en cuenta es no realizar ningún ataque o limpieza que pueda dañar la superficie y deteriorar las propiedades de las nanostructuras. En este apartado, se realiza un análisis completo de una serie de tres muestras: GaAs (bulk), un pozo cuántico superficial (SQW) de Ino.5Gao.5As y SQDs de Ino.5Gao.5As. Para ello, a cada una de las muestras se le realizan medidas de I-V en distintas condiciones ambientales. En primer lugar, siguiendo los resultados obtenidos ópticamente, se lleva a cabo una comparación de la respuesta eléctrica en vacío y aire. A pesar de que todas las muestras presentan un carácter más resistivo en vacío que en aire, se observa una mayor influencia sobre la muestra de SQD. En vacío, la resistencia de los SQDs decrece un 99% respecto de su valor en aire, mientras que la variación de la muestras de GaAs e Ino.5Gao.5As SQW muestran una reducción, respectivamente, del 31% y del 20%. En segundo lugar, se realiza una evaluación aproximada del posible efecto de la humedad en la resistencia superficial de las muestras mediante la exhalación humana. Como resultado se obtiene, que tras la exhalación, la resistencia disminuye bruscamente y recupera su valor inicial cuando dicho proceso concluye. Este resultado preliminar indica que la humedad es un factor crítico en las propiedades eléctricas de los puntos cuánticos superficiales. Para la determinación del papel de la humedad en la respuesta eléctrica, se somete a las muestras de SQD y SQW a ambientes con humedad relativa (RH, de la siglas del inglés) controlada y se analiza el efecto sobre la conductividad superficial. Tras la variación de la RH desde 0% hasta el 70%, se observa que la muestra SQW no cambia su comportamiento eléctrico al variar la humedad del ambiente. Sin embargo, la respuesta de la muestra SQD define dos regiones bien diferenciadas, una de alta sensibilidad para valores por debajo del 50% de RH, en la que la resistencia disminuye hasta en un orden de magnitud y otra, de baja sensibilidad (>50%), donde el cambio de la resistencia es menor. Este resultado resalta la especial relevancia no sólo de la composición sino también de la morfología de la nanostructura superficial en el carácter sensitivo de la muestra. Por último, se analiza la influencia de la iluminación en la sensibilidad de la muestra. Nuevamente, se somete a las muestras SQD y SQW a una irradiación de luz de distinta energía y potencia a la vez que se varía controladamente la humedad ambiental. Una vez más, se observa que la muestra SQW no presenta ninguna variación apreciable con las alteraciones del entorno. Su resistencia superficial permanece prácticamente inalterable tanto al modificar la potencia de la luz incidente como al variar la energía de la irradiación. Por el contrario, en la muestra de SQD se obtiene una reducción la resistencia superficial de un orden de magnitud al pasar de condiciones de oscuridad a iluminación. Con respecto a la potencia y energía de la luz incidente, se observa que a pesar de que la muestra no experimenta variaciones notables con la potencia de la irradiación, esta sufre cambios significativos con la energía de la luz incidente. Cuando se ilumina con energías por encima de la energía de la banda prohibida (gap) del GaAs (Eg ~1.42 eV ) se produce una reducción de la resistencia de un orden de magnitud en atmósferas húmedas, mientras que en atmósferas secas la conductividad superficial permanece prácticamente constante. Sin embargo, al inicidir con luz de energía menor que Eg, el efecto que se produce en la respuesta eléctrica es despreciable. Esto se atribuye principalmente a la densidad de portadores fotoactivados durante la irradiación. El volumen de portadores excita dos depende de la energía de la luz incidente. De este modo, cuando la luz que incide tiene energía menor que el gap, el volumen de portadores generados es pequeño y no contribuye a la conductividad superficial. Por el contrario, cuando la energía de la luz incidente es alta (Eg), el volumen de portadores activados es elevado y éstos contribuyen significantemente a la conductividad superficial. La combinación de ambos agentes, luz y humedad, favorece el proceso de adsorción de moléculas y, por tanto, contribuye a la reducción de la densidad de estados superficiales, dando lugar a una modificación de la estructura electrónica y consecuentemente favoreciendo o dificultando el transporte de portadores. ABSTRACT Uncapped three-dimensional (3D) nanostructures have been generally grown to assess their structural quality. However, the tremendous growing importance of the impact of the environment on life has become such nanosystems in very promising candidates for the development of sensing devices. Their direct exposure to changes in the local surrounding may influence their physical properties being a perfect sign of the atmosphere quality. The goal of this thesis is the research of Ino.5Gao.5As surface quantum dots (SQDs) on GaAs(001), covering from their growth to device fabrication, for sensing applications. The achievement of this goal relies on the design, growth and sample characterization, along with device fabrication and characterization. The first issue of the thesis is devoted to analyze the main growth parameters affecting the physical properties of the Ino.5Gao.5As SQDs. It is well known that the growing conditions (growth temperature , deposition rate, V/III flux ratio and treatment after active layer growth) directly affect the physical properties of the epilayer. In this part, taking advantage of the previous results in the group regarding Ino.5Gao.5As QD growth temperature and V/III ratio, the effect of the growth rate and the temperature treatment after QDs growth nucleation is evaluated. Setting the QDs growth temperature at 430°C and the V/III flux ratio to ~20, it is found that the most appropriate conditions rely on growing the QDs at 0.07ML/s and just after QD nucleation, rapidly dropping and again raising 100°C the substrate temperature with respect to the temperature of QD growth. The combination of growing at a fast enough growth rate to promote molecule migration but sufficiently slow to allow QD nucleation, together with the sharp variation of the temperature preserving their shape and composition yield to high density, homogeneous Ino.5Gao.5As SQDs. Besides, it is also demonstrated that this high quality SQDs show excellent optical properties even at room temperature (RT). One of the characteristics by which In0.5Ga0.5As/GaAs SQDs are considered promising candidates for sensing applications is the crucial role that surface plays when interacting with the gases constituting the atmosphere. Therefore, in an attempt to develop sensing devices, the influence of the environment on the physical properties of the samples is evaluated. By comparing the resulting photoluminescence (PL) of SQDs with buried QDs (BQDs), it is found that BQDs do not exhibit any significant variation when changing the environmental conditions whereas, the external conditions greatly act on the SQDs optical properties. On one hand, it is evidenced that PL intensity of SQDs sharply quenches under vacuum and clearly decreases under dry-pure gases atmospheres (N2, O2). On the other hand, it is shown that, in water containing atmospheres, the SQDs PL intensity is maintained with respect to that in air. Moreover, it is found that neither the full width at half maximun nor the emission wavelength manifest any noticeable change indicating that the QDs are not structurally altered by the external atmosphere. These results decisively point to the processes taking place at the surface such as coupling between confined and surface states, to be responsible of this extraordinary behavior. A further analysis of the impact of the atmosphere composition on the optical characteristics is conducted. A sample containing one uncapped In0.5Ga0.5As QDs layer is exposed to different environments. Several solvents presenting different polarity, atomic composition and molecular mass, are used to change the atmosphere composition. It is revealed that low polarity and heavy molecules cause a greater variation on the PL intensity. Besides, oxygen is demonstrated to play a decisive role on the PL response. Results indicate that in presence of oxygen-containing molecules, the PL intensity experiments a less reduction than that suffered in presence of nonoxygen-containing molecules, 90% compared to 77% signal respect to the emission in air. In agreement with these results, it is demonstrated that high polarity and lighter molecules containing oxygen are more easily adsorbed, and consequently, PL intensity is less affected. The presence of defects, unsaturated bonds and in general localized states in the surface are proposed to act as nonradiative recombination centers deteriorating the PL emission of the sample. Therefore, suppression or reduction of the density of such states may lead to an increase or, at least, conservation of the PL signal. This research denotes that the interaction between sample surface and molecules in the atmosphere modifies the surface characteristics altering thus the optical properties. This is attributed to the likely adsoption of some molecules onto the surface passivating the nonradiative recombination centers, and consequently, not deteriorating the PL emission. Aiming for sensors development, samples are processed and electrically characterized under different external conditions. Samples are processed with two square (Ti/Au) contacts. During the processing, especial attention must be paid to the surface treatment. Any process that may damage the surface such as plasma etching or annealing must be avoided to preserve the features of the surface nanostructures. A set of three samples: a GaAs (bulk), In0.5Ga0.5As SQDs and In0.5Ga0.5As surface quantum well (SQW) are subjected to a throughout evaluation. I-V characteristics are measured following the results from the optical characterization. Firstly, the three samples are exposed to vacuum and air. Despite the three samples exhibit a more resistive character in vacuum than in air, it is revealed a much more clear influence of the pressure atmosphere in the SQDs sample. The sheet resistance (Rsh) of SQDs decreases a 99% from its response value under vacuum to its value in air, whereas Rsh of GaAs and In0.5Ga0.5As SQW reduces its value a 31% and a 20%, respectively. Secondly, a rough analysis of the effect of the human breath on the electrical response evidences the enormous influence of moisture (human breath is composed by several components but the one that overwhelms all the rest is the high concentration of water vapor) on the I-V characteristics. Following this result, In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW are subjected to different controlled relative humidity (RH) environments (from 0% to 70%) and electrically characterized. It is found that SQW shows a nearly negligible Rsh variation when increasing the RH in the surroundings. However, the response of SQDs to changes in the RH defines two regions. Below 50%, high sensitive zone, Rsh of SQD decreases by more than one order of magnitude, while above 50% the dependence of Rsh on the RH becomes weaker. These results remark the role of the surface and denote the existence of a finite number of surface states. Nevertheless, most significantly, they highlight the importance not only of the material but also of the morphology. Finally, the impact of the illumination is determined by means of irradiating the In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW samples with different energy and power sources. Once again, SQW does not exhibit any correlation between the surface conductivity and the external conditions. Rsh remains nearly unalterable independently of the energy and power of the incident light. Conversely, Rsh of SQD experiences a decay of one order of magnitude from dark-to-photo conditions. This is attributed to the less density of surface states of SQW compared to that of SQDs. Additionally, a different response of Rsh of SQD with the energy of the impinging light is found. Illuminating with high energy light results in a Rsh reduction of one order of mag nitude under humid atmospheres, whereas it remains nearly unchanged under dry environments. On the contrary, light with energy below the bulk energy bandgap (Eg), shows a negligible effect on the electrical properties regardless the local moisture. This is related to the density of photocarriers generated while lighting up. Illuminating with excitation energy below Eg affects a small absorption volume and thus, a low density of photocarriers may be activated leading to an insignificant contribution to the conductivity. Nonetheless, irradiating with energy above the Eg can excite a high density of photocarriers and greatly improve the surface conductivity. These results demonstrate that both illumination and humidity are therefore needed for sensing. The combination of these two agents improves the surface passivation by means of molecule adsorption reducing the density of surface states, thus modifying the electronic structures, and consequently, promoting the carrier motion.

Surface studies in ultra high vacuum

An ultra high vacuum system capable of attaining pressures of 10-12 mm Hg was used for thermal desorption experiments. The metal chosen for these experiments was tantalum because of its suitability for thermal desorption experiments and because relatively little work has been done using this metal. The gases investigated were carbon monoxide, hydrogen and ethylene. The kinetic and thermodynamic parameters relating to the desorption reaction were calculated and the values obtained related to the reaction on the surface. The thermal desorption reaction was not capable of supplying all the information necessary to form a complete picture of the desorption reaction. Further information was obtained by using a quadrupole mass spectrometer to analyse the desorbed species. The identification of the desorbed species combined with the value of the desorption parameters meant that possible adatom structures could be postulated. A combination of these two techniques proved to be a very powerful tool when investigating gas-metal surface reactions and gave realistic values for the measured parameters such as the surface coverage, order of reaction, the activation energy and pre-exponential function for desorption. Electron microscopy and X-ray diffraction were also used to investigate the effect of the gases on the metal surface.

The characterisation of clean metal surfaces

The most perfectly structured metal surface observed in practice is that of a field evaporated field-ion microscope specimen. This surface has been characterised by adopting various optical analogue techniques. Hence a relationship has been determined between the structure of a single plane on the surface of a field-ion emitter and the geometry of a binary zone plate. By relating the known focussing properties of such a zone plate to those obtained from the projected images of such planes in a field-ion micrograph, it is possible to extract new information regarding the local magnification of the image. Further to this, it has been shown that the entire system of planes comprising the field-ion imaging surface may be regarded as a moire pattern formed between over-lapping zone plates. The properties of such moire zone plates are first established in an analysis of the moire pattern formed between zone plates on a flat surface. When these ideas are applied to the field-ion image it becomes possible to deduce further information regarding the precise topography of the emitter. It has also become possible to simulate differently proJected field-ion images by overlapping suitably aberrated zone plates. Low-energy ion bombardment is an essential preliminary to much surface research as a means of producing chemically clean surfaces. Hence it is important to know the nature and distribution of the resultant lattice damage, and the extent to which it may be removed by annealing. The field-ion microscope has been used to investigate such damage because its characterisation lies on the atomic scale. The present study is concerned with the in situ sputtering of tungsten emitters using helium, neon, argon and xenon ions with energies in the range 100eV to 1keV, together with observations of the effect of annealing. The relevance of these results to surface cleaning schedules is discussed.

Atmospheric plasma treatment of porous polymer constructs for tissue engineering applications

Porous 3D polymer scaffolds prepared by TIPS from PLGA (53:47) and PS are intrinsically hydrophobic which prohibits the wetting of such porous media by water. This limits the application of these materials for the fabrication of scaffolds as supports for cell adhesion/spreading. Here we demonstrate that the interior surfaces of polymer scaffolds can be effectively modified using atmospheric air plasma (AP). Polymer films (2D) were also modified as control. The surface properties of wet 2D and 3D scaffolds were characterised using zeta-potential and wettability measurements. These techniques were used as the primary screening methods to assess surface chemistry and the wettability of wet polymer constructs prior and after the surface treatment. The surfaces of the original polymers are rather hydrophobic as highlighted but contain acidic functional groups. Increased exposure to AP improved the water wetting of the treated surfaces because of the formation of a variety of oxygen and nitrogen containing functions. The morphology and pore structure was assessed using SEM and a liquid displacement test. The PLGA and PS foam samples have central regions which are open porous interconnected networks with maximum pore diameters of 49 μm for PLGA and 73 μm for PS foams. (Figure Presented) © 2007 Wiley-VCH Verlag GmbH & Co. KGaA.

Electro and Magneto-Electropolished Surface Micro-Patterning on Binary and Ternary Nitinol

In this study, an Atomic Force Microscopy (AFM) roughness analysis was performed on non-commercial Nitinol alloys with Electropolished (EP) and Magneto-Electropolished (MEP) surface treatments and commercially available stents by measuring Root-Mean-Square (RMS) , Average Roughness (Ra), and Surface Area (SA) values at various dimensional areas on the alloy surfaces, ranging from (800 x 800 nm) to (115 x 115µm), and (800 x 800 nm) to (40 x 40 µm) on the commercial stents. Results showed that NiTi-Ta 10 wt% with an EP surface treatment yielded the highest overall roughness, while the NiTi-Cu 10 wt% alloy had the lowest roughness when analyzed over (115 x 115 µm). Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analysis revealed unique surface morphologies for surface treated alloys, as well as an aggregation of ternary elements Cr and Cu at grain boundaries in MEP and EP surface treated alloys, and non-surface treated alloys. Such surface micro-patterning on ternary Nitinol alloys could increase cellular adhesion and accelerate surface endothelialization of endovascular stents, thus reducing the likelihood of in-stent restenosis and provide insight into hemodynamic flow regimes and the corrosion behavior of an implantable device influenced from such surface micro-patterns.

Assessment of biodegradable magnesium alloys for enhanced mechanical and biocompatible properties

Biomaterials have been used for more than a century in the human body to improve body functions and replace damaged tissues. Currently approved and commonly used metallic biomaterials such as, stainless steel, titanium, cobalt chromium and other alloys have been found to have adverse effects leading in some cases, to mechanical failure and rejection of the implant. The physical or chemical nature of the degradation products of some implants initiates an adverse foreign body reaction in the tissue. Some metallic implants remain as permanent fixtures, whereas others such as plates, screws and pins used to secure serious fractures are removed by a second surgical procedure after the tissue has healed sufficiently. However, repeat surgical procedures increase the cost of health care and the possibility of patient morbidity. This study focuses on the development of magnesium based biodegradable alloys/metal matrix composites (MMCs) for orthopedic and cardiovascular applications. The Mg alloys/MMCs possessed good mechanical properties and biocompatible properties. Nine different compositions of Mg alloys/MMCs were manufactured and surface treated. Their degradation behavior, ion leaching, wettability, morphology, cytotoxicity and mechanical properties were determined. Alloying with Zn, Ca, HA and Gd and surface treatment resulted in improved mechanical properties, corrosion resistance, reduced cytotoxicity, lower pH and hydrogen evolution. Anodization resulted in the formation of a distinct oxide layer (thickness 5-10 μm) as compared with that produced on mechanically polished samples (~20-50 nm) under ambient conditions. It is envisaged that the findings of this research will introduce a new class of Mg based biodegradable alloys/MMCs and the emergence of innovative cardiovascular and orthopedic implant devices.^

Study of porcelain-zirconia composites for dental applications

Materiais compósitos restauradores representam um dos mais bem sucedidos biomateriais na pesquisa moderna, na substituição do tecido biológico em aparência e função. Nesta linha, a porcelana feldspática tem sido largamente usada em odontologia devido suas interessantes qualidades como estabilidade de cor, propriedades estéticas, elevada durabilidade mecânica, biocompatibilidade, baixa condutividade térmica e elevada resistência ao desgaste. Entretanto, este material é frágil e pode falhar em ambiente oral devido ao micro-vazamento, baixa resistência à tração, descolagem ou fratura. Assim, para melhorar as propriedades mecânicas da porcelana, a zircônia parcialmente estabilizada com Ítria (Y-TZP) pode ser uma boa alternativa para fortalecer e produzir infraestruturas totalmente cerâmicas (coroas e próteses parciais fixas). Portanto, este estudo tem por objetivo avaliar as propriedades mecânicas e características microestruturais da porcelana reforçada com zircônia (3Y-TZP) em diferentes conteúdos e as variáveis que afetam as propriedades mecânicas destes materiais. O estudo de caracterização revelou que a zircônia comercial apresenta melhores resultados quando comparada com a zircônia sintetizada pelo CPM. Assim, os estudos seguintes utilizaram a zircônia comercial para todos os testes requeridos. As partículas de zircônia apresentam elevadas propriedades mecânicas quando comparadas a zircônia aglomerada. Os diferentes conteúdos revelam que as propriedades mecânicas dos compósitos aumentam com o aumento do conteúdo volumétrico até 30% vol.% (198,5Mpa), ou seja, maior resistência à flexão quando comparada com os outros compósitos. Do mesmo modo, a resistência ao desgaste para os compósitos com (30%, vol.% de zircônia) apresenta valores superiores quando comparado aos demais compósitos. Na adesão cerâmico-cerâmico a porcelana exibe elevada adesão para a superfície de zircônia porosa quando comparada a superfície rugosa. Os furos superficiais (PZ) e aplicação de compósitos com camada intermediária (RZI) na zircônia causam separadamente uma melhoria da resistência ao cisalhamento da zircônia-porcelana quando comparados as amostras convencionais de zircônia-porcelana (RZ), embora não sejam estatisticamente significativas (p>0.05). A presença de uma camada intermediaria produz um aumento significativo na força de ligação (~55%) em relação as amostras convencionais (RZ). Portanto, a correta a correta configuração e tratamento superficial podem produzir subestruturas com qualidade e força de ligação adequadas aos requisitos odontológicos.

Formation of sub-7 nm feature size PS-b-P4VP block copolymer structures by solvent vapour process

The nanometer range structure produced by thin films of diblock copolymers makes them a great of interest as templates for the microelectronics industry. We investigated the effect of annealing solvents and/or mixture of the solvents in case of symmetric Poly (styrene-block-4vinylpyridine) (PS-b-P4VP) diblock copolymer to get the desired line patterns. In this paper, we used different molecular weights PS-b-P4VP to demonstrate the scalability of such high χ BCP system which requires precise fine-tuning of interfacial energies achieved by surface treatment and that improves the wetting property, ordering, and minimizes defect densities. Bare Silicon Substrates were also modified with polystyrene brush and ethylene glycol self-assembled monolayer in a simple quick reproducible way. Also, a novel and simple in situ hard mask technique was used to generate sub-7nm Iron oxide nanowires with a high aspect ratio on Silicon substrate, which can be used to develop silicon nanowires post pattern transfer.

Swellable polymer films containing Au nanoparticles for point-of-care therapeutic drug monitoring using surface-enhanced Raman spectroscopy

Large (10 × 10 cm) sheets of surface-enhanced Raman spectroscopy (SERS) active polymer have been prepared by stabilising metal nanoparticle aggregates within dry hydroxyethylcellulose (HEC) films. In these films the aggregates are protected by the polymer matrix during storage but in use they are released when aqueous analyte droplets cause the films to swell to their gel form. The fact that these "Poly-SERS" films can be prepared in bulk but then cut to size and stored in air before use means that they provide a cost effective and convenient method for routine SERS analysis. Here we have tested both Ag and Au Poly-SERS films for use in point-of-care monitoring of therapeutic drugs, using phenytoin as the test compound. Phenytoin in water could readily be detected using Ag Poly-SERS films but dissolving the compound in phosphate buffered saline (PBS) to mimic body fluid samples caused loss of the drug signal due to competition for metal surface sites from Cl^- ions in the buffer solution. However, with Au Poly-SERS films there was no detectable interference from Cl^- and these materials allowed phenytoin to be detected at 1.8 mg L^-1, even in PBS. The target range of detection of phenytoin in therapeutic drug monitoring is 10-20 mg L^-1. With the Au Poly-SERS films, the absolute signal generated by a given concentration of phenytoin was lower for the films than for the parent colloid but the SERS signals were still high enough to be used for therapeutic monitoring, so the cost in sensitivity for moving from simple aqueous colloids to films is not so large that it outweighs the advantages which the films bring for practical applications, in particular their ease of use and long shelf life.

Développement et caractérisation de nouveaux nanocomposites polymères électriquement conductueurs pour plaques bipolaires de piles à combustible à membrane échangeuse de protons, PEMFC

Face à la diminution des ressources énergétiques et à l’augmentation de la pollution des énergies fossiles, de très nombreuses recherches sont actuellement menées pour produire de l’énergie propre et durable et pour réduire l’utilisation des sources d’énergies fossiles caractérisées par leur production intrinsèque des gaz à effet de serre. La pile à combustible à membrane échangeuse de protons (PEMFC) est une technologie qui prend de plus en plus d’ampleur pour produire l’énergie qui s’inscrit dans un contexte de développement durable. La PEMFC est un dispositif électrochimique qui fonctionne selon le principe inverse de l’électrolyse de l’eau. Elle convertit l’énergie de la réaction chimique entre l’hydrogène et l’oxygène (ou l’air) en puissance électrique, chaleur et eau; son seul rejet dans l’atmosphère est de la vapeur d’eau. Une pile de type PEMFC est constituée d’un empilement Électrode-Membrane-Électrode (EME) où la membrane consiste en un électrolyte polymère solide séparant les deux électrodes (l’anode et la cathode). Cet ensemble est intégré entre deux plaques bipolaires (BP) qui permettent de collecter le courant électrique et de distribuer les gaz grâce à des chemins de circulation gravés sur chacune de ses deux faces. La plupart des recherches focalisent sur la PEMFC afin d’améliorer ses performances électriques et sa durabilité et aussi de réduire son coût de production. Ces recherches portent sur le développement et la caractérisation des divers éléments de ce type de pile; y compris les éléments les plus coûteux et les plus massifs, tels que les plaques bipolaires. La conception de ces plaques doit tenir compte de plusieurs paramètres : elles doivent posséder une bonne perméabilité aux gaz et doivent combiner les propriétés de résistance mécanique, de stabilité chimique et thermique ainsi qu’une conductivité électrique élevée. Elles doivent aussi permettre d’évacuer adéquatement la chaleur générée dans le cœur de la cellule. Les plaques bipolaires métalliques sont pénalisées par leur faible résistance à la corrosion et celles en graphite sont fragiles et leur coût de fabrication est élevé (dû aux phases d’usinage des canaux de cheminement des gaz). C’est pourquoi de nombreuses recherches sont orientées vers le développement d’un nouveau concept de plaques bipolaires. La voie la plus prometteuse est de remplacer les matériaux métalliques et le graphite par des composites à matrice polymère. Les plaques bipolaires composites apparaissent attrayantes en raison de leur facilité de mise en œuvre et leur faible coût de production mais nécessitent une amélioration de leurs propriétés électriques et mécaniques, d’où l’objectif principal de cette thèse dans laquelle on propose: i) un matériau nanocomposite développé par extrusion bi-vis qui est à base de polymères chargés d’additifs solides conducteurs, incluant des nanotubes de carbone. ii) fabriquer un prototype de plaque bipolaire à partir de ces matériaux en utilisant le procédé de compression à chaud avec un refroidissement contrôlé. Dans ce projet, deux polymères thermoplastiques ont été utilisés, le polyfluorure de vinylidène (PVDF) et le polyéthylène téréphtalate (PET). Les charges électriquement conductrices sélectionnées sont: le noir de carbone, le graphite et les nanotubes de carbones. La combinaison de ces charges conductrices a été aussi étudiée visant à obtenir des formulations optimisées. La conductivité électrique à travers l’épaisseur des échantillons développés ainsi que leurs propriétés mécaniques ont été soigneusement caractérisées. Les résultats ont montré que non seulement la combinaison entre les charges conductrices influence les propriétés électriques et mécaniques des prototypes développés, mais aussi la distribution de ces charges (qui de son côté dépend de leur nature, leur taille et leurs propriétés de surface), avait aidé à améliorer les propriétés visées. Il a été observé que le traitement de surface des nanotubes de carbone avait aidé à l’amélioration de la conductivité électrique et la résistance mécanique des prototypes. Le taux de cristallinité généré durant le procédé de moulage par compression des prototypes de plaques bipolaires ainsi que la cinétique de cristallisation jouent un rôle important pour l’optimisation des propriétés électriques et mécaniques visées.

Synthesis, characterization and chemical vapor deposition of transition metal di(tert-butyl)amido compounds

Although the transition metal chemistry of many dialkylamido ligands has been well studied, the chemistry of the bulky di(tert-butyl)amido ligand has been largely overlooked. The di(tert-butyl)amido ligand is well suited for synthesizing transition metal compounds with low coordination numbers; such compounds may exhibit interesting structural, physical, and chemical properties. Di(tert-butyl)amido complexes of transition metals are expected to exhibit high volatilities and low decomposition temperatures, thus making them well suited for the chemical vapor deposition of metals and metal nitrides. Treatment of MnBr₂(THF)₂, FeI₂, CoBr₂(DME), or NiBr₂(DME) with two equivalents of LiN(t-Bu)2 in benzene affords the two-coordinate complex M[N(t-Bu)₂]₂, where M is Mn, Fe, Co, or Ni. Crystallographic studies show that the M-N distances decrease across the series: 1.9365 (Mn), 1.8790 (Fe), 1.845 (Co), 1.798 Å (Ni). The N-M- N angles are very close to linear for Mn and Fe (179.30 and 179.45°, respectively), but bent for Co and Ni (159.2 and 160.90°, respectively). As expected, the d⁵ Mn complex has a magnetic moment of 5.53 μΒ that is very close to the spin only value. The EPR spectrum is nearly axial with a low E/D ratio of 0.014. The d⁶ Fe compound has a room temperature magnetic moment of 5.55 μΒ indicative of a large orbital angular momentum contribution. It does not exhibit a Jahn-Teller distortion despite the expected doubly degenerate ground state. Applied field Mössbauer spectroscopy shows that the effective internal hyperfine field is unusually large, Hint = 105 T. The magnetic moments of Co[N(t-Bu)₂]₂ and Ni[N(t-Bu)₂]₂ are 5.24 and 3.02 μΒ respectively. Both are EPR silent at 4.2 K. Treatment of TiCl₄ with three equivalents of LiN(t-Bu)2 in pentane affords the briding imido compound Ti₂[μ-N(t-Bu)]₂Cl₂[N(t-Bu)₂]₂ via a dealkylation reaction. Rotation around the bis(tert-butyl)amido groups is hindered, with activation parameters of ΔH‡ = 12.8 ± 0.6 kcal mol-1 and ΔS‡ = -8 ± 2 cal K-1 ·mol-1, as evidenced by variable temperature 1H NMR spectroscopy. Treatment of TiCl₄ with two equivalents of HN(t-Bu)₂ affords Ti₂Cl₆[N(t-Bu)₂]₂. This complex shows a close-contact of 2.634(3) Å between Ti and the carbon atom of one of the CH₃ substituents on the tert-butyl groups. Theoretical considerations and detailed structural comparisons suggest this interaction is not agostic in nature, but rather is a consequence of interligand repulsions. Treatment of NiI₂(PPh3)₂ and PdCl₂(PPh₃)₂ with LiN(t-Bu)₂in benzene affords Ni[N(t-Bu)₂](PPh₃)I and Pd₃(μ₂-NBut₂)2(μ₂-PPh₂)Ph(PPh₃) respectively. The compound Ni[N(t-Bu)₂](PPh₃)I has distorted T-shape in geometry, whereas Pd₃(μ₂-NBut₂)₂(μ₂-PPh₂)Ph(PPh₃) contains a triangular palladium core. Manganese nitride films were grown from Mn[N(t-Bu)₂]₂ in the presence of anhydrous ammonia. The growth rate was several nanometers per minute even at the remarkably low temperature of 80⁰C. As grown, the films are carbon- and oxygen-free, and have a columnar morphology. The spacings between the columns become smaller and the films become smoother as the growth temperature is increased. The composition of the films is consistent with a stoichiometry of Mn₅N₂.

Effect of graphene substrate on the SERS Spectra of Aromatic bifunctional molecules on metal nanoparticles

The design of molecular sensors plays a very important role within nanotechnology and especially in the development of different devices for biomedical applications. Biosensors can be classified according to various criteria such as the type of interaction established between the recognition element and the analyte or the type of signal detection from the analyte (transduction). When Raman spectroscopy is used as an optical transduction technique the variations in the Raman signal due to the physical or chemical interaction between the analyte and the recognition element has to be detected. Therefore any significant improvement in the amplification of the optical sensor signal represents a breakthrough in the design of molecular sensors. In this sense, Surface-Enhanced Raman Spectroscopy (SERS) involves an enormous enhancement of the Raman signal from a molecule in the vicinity of a metal surface. The main objective of this work is to evaluate the effect of a monolayer of graphene oxide (GO) on the distribution of metal nanoparticles (NPs) and on the global SERS enhancement of paminothiophenol (pATP) and 4-mercaptobenzoic acid (4MBA) adsorbed on this substrate. These aromatic bifunctional molecules are able to interact to metal NPs and also they offer the possibility to link with biomolecules. Additionally by decorating Au or Ag NPs on graphene sheets, a coupled EM effect caused by the aggregation of the NPs and strong electronic interactions between Au or Ag NPs and the graphene sheets are considered to be responsible for the significantly enhanced Raman signal of the analytes [1-2]. Since there are increasing needs for methods to conduct reproducible and sensitive Raman measurements, Grapheneenhanced Raman Scattering (GERS) is emerging as an important method [3].

Evaluation of dry protonated calcium alginate beads for biosorption applications and studies of lead uptake

Alginate polysaccharide is a promising biosorbent for metal uptake. Dry protonated calcium alginate beads for biosorption applications were prepared, briefly characterized and tested for lead uptake. Several advantages of this biosorbent are reported and discussed in comparison with other alginate-based sorbents. The alginate beads contained 4.7 mmol/g of COOH groups, which suffered hydrolysis near pH 4. The Weber and Morris model, applied to kinetic results of lead uptake, showed that intraparticle diffusion was the rate-controlling step in lead sorption by dry alginate beads. Equilibrium experiments were performed and the data were fitted with different isotherm models. The Langmuir equation was the most adequate to model lead sorption. The maximum uptake capacity (qmax) was estimated as 339 mg/g and the Langmuir constant (b) as 0.84 l/mg. These values were compared with that of other sorbents found in the literature, indicating that dry protonated calcium alginate beads are among the best biosorbents for the treatment and recovery of heavy metals from aqueous streams.

Morphological analysis of glass, carbon and glass/carbon fiber posts and bonding to self or dual-cured resin luting agents

OBJECTIVE: The aim of this study was to evaluate the morphology of glass (GF), carbon (CF) and glass/carbon (G/CF) fiber posts and their bond strength to self or dual-cured resin luting agents. MATERIAL AND METHODS: Morphological analysis of each post type was conducted under scanning electron microscopy (SEM). Bond strength was evaluated by microtensile test after bisecting the posts and re-bonding the two halves with the luting agents. Data were subjected to two-way ANOVA and Tukey's test (α=0.05). Failure modes were evaluated under optical microscopy and SEM. RESULTS: GF presented wider fibers and higher amount of matrix than CF, and G/CF presented carbon fibers surrounded by glass fibers, and both involved by matrix. For CF and GF, the dual-cured material presented significantly higher (p<0.05) bond strength than the self-cured agent. For the dual agent, CF presented similar bond strength to GF (p>0.05), but higher than that of G/CF (p<0.05). For the self-cured agent, no significant differences (p>0.05) were detected, irrespective of the post type. For GF and G/CF, all failures were considered mixed, while a predominance of adhesive failures was detected for CF. CONCLUSION: The bonding between fiber posts and luting agents was affected by the type of fibers and polymerization mode of the cement. When no surface treatment of the post is performed, the bonding between glass fiber post and dual-cured agent seems to be more reliable.