Extractants to assess zinc phytoavailability in mineral fertilizer and industrial by-products

Efficient analytical methods for the quantification of plant-available Zn contained in mineral fertilizers and industrial by-products are fundamental for the control and marketing of these inputs. In this sense, there are some doubts on the part of the scientific community as well as of the fertilizer production sector, whether the extractor requested by the government (Normative Instruction No. 28, called 2nd extractor), which is citric acid 2 % (2 % CA) (Brasil, 2007b), is effective in predicting the plant availability of Zn via mineral fertilizers and about the agronomic significance of the required minimal solubility of 60 % compared to the total content (HCl) (Brasil, 2007a). The purpose of this study was to evaluate the alternative extractors DTPA, EDTA, neutral ammonium citrate (NAC), buffer solution pH 6.0, 10 % HCl, 10 % sulfuric acid, 1 % acetic acid, water, and hot water to quantify the contents of Zn available for maize and compare them with indices of agronomic efficiency of fertilizers and industrial by-products when applied to dystrophic Clayey Red Latosol and Dystrophic Alic Red Yellow Latosol with medium texture. The rate of Zn applied to the soil was 5 mg kg-1, using the sources zinc sulfate, commercial granular zinc, ash and galvanic sludge, ash and two brass slags. Most Zn was extracted from the sources by DTPA, 10 % HCl, NAC, 1% acetic acid, and 10 % sulfuric acid. Recovery by the extractors 2 % CA, EDTA, water, and hot water was low. The agronomic efficiency index was found to be high when using galvanic sludge (238 %) and commercial granular zinc (142 %) and lower with brass slag I and II (67 and 27 %, respectively). The sources galvanizing ash and brass ash showed solubility lower than 60 % in 2 % CA, despite agronomic efficiency indices of 78 and 125 %, respectively. The low agronomic efficiency index of industrial by-products such as brass slag I and galvanizing ash can be compensated by higher doses, provided there is no restriction, as well as for all other sources, in terms of contaminant levels of arsenic, cadmium, chromium, lead, and mercury as required by law (Normative Instruction No 27/2006). The implementation of 2nd extractor 2 % CA and the requirement of minimum solubility for industrial by-products could restrict the use of alternative sources as potential Zn sources for plants.

Anàlisi d’un incendi en una nau industrial a Gavà. Conclusions per a l’aplicació del (RSCIEI) en naus de tipus A en horitzontal

1. SINISTRE D’UNA NAU INDÚSTRIAL A GAVÀ 2. ANÀLISI DE SINISTRES DE PÒRTICS ENTRE MITGERES 3. CONTROL DE LA FALLADA DE LES ESTRUCTURES AMB MESURES PASSIVES 3.1 Definició del model simulats 3.2 Paràmetres de càlcul amb OZONE 3.3 Corbes d’incendi resultants del model de zones 1D 3.4 Control tèrmic de l’estructura amb sistemes de ventilació 3.5 Control tèrmic de l’estructura amb aïllament 3.6 Taula de resultats 3.7 Conclusions 1D 4. SIMULACIÓ DELS INCENDIS AMB FIRE DYNAMICS SIMULATOR

Three essays on major trends in a slow clockspeed industry : the case of industrial automation

The motivation for this research initiated from the abrupt rise and fall of minicomputers which were initially used both for industrial automation and business applications due to their significantly lower cost than their predecessors, the mainframes. Later industrial automation developed its own vertically integrated hardware and software to address the application needs of uninterrupted operations, real-time control and resilience to harsh environmental conditions. This has led to the creation of an independent industry, namely industrial automation used in PLC, DCS, SCADA and robot control systems. This industry employs today over 200'000 people in a profitable slow clockspeed context in contrast to the two mainstream computing industries of information technology (IT) focused on business applications and telecommunications focused on communications networks and hand-held devices. Already in 1990s it was foreseen that IT and communication would merge into one Information and communication industry (ICT). The fundamental question of the thesis is: Could industrial automation leverage a common technology platform with the newly formed ICT industry? Computer systems dominated by complex instruction set computers (CISC) were challenged during 1990s with higher performance reduced instruction set computers (RISC). RISC started to evolve parallel to the constant advancement of Moore's law. These developments created the high performance and low energy consumption System-on-Chip architecture (SoC). Unlike to the CISC processors RISC processor architecture is a separate industry from the RISC chip manufacturing industry. It also has several hardware independent software platforms consisting of integrated operating system, development environment, user interface and application market which enables customers to have more choices due to hardware independent real time capable software applications. An architecture disruption merged and the smartphone and tablet market were formed with new rules and new key players in the ICT industry. Today there are more RISC computer systems running Linux (or other Unix variants) than any other computer system. The astonishing rise of SoC based technologies and related software platforms in smartphones created in unit terms the largest installed base ever seen in the history of computers and is now being further extended by tablets. An underlying additional element of this transition is the increasing role of open source technologies both in software and hardware. This has driven the microprocessor based personal computer industry with few dominating closed operating system platforms into a steep decline. A significant factor in this process has been the separation of processor architecture and processor chip production and operating systems and application development platforms merger into integrated software platforms with proprietary application markets. Furthermore the pay-by-click marketing has changed the way applications development is compensated: Three essays on major trends in a slow clockspeed industry: The case of industrial automation 2014 freeware, ad based or licensed - all at a lower price and used by a wider customer base than ever before. Moreover, the concept of software maintenance contract is very remote in the app world. However, as a slow clockspeed industry, industrial automation has remained intact during the disruptions based on SoC and related software platforms in the ICT industries. Industrial automation incumbents continue to supply systems based on vertically integrated systems consisting of proprietary software and proprietary mainly microprocessor based hardware. They enjoy admirable profitability levels on a very narrow customer base due to strong technology-enabled customer lock-in and customers' high risk leverage as their production is dependent on fault-free operation of the industrial automation systems. When will this balance of power be disrupted? The thesis suggests how industrial automation could join the mainstream ICT industry and create an information, communication and automation (ICAT) industry. Lately the Internet of Things (loT) and weightless networks, a new standard leveraging frequency channels earlier occupied by TV broadcasting, have gradually started to change the rigid world of Machine to Machine (M2M) interaction. It is foreseeable that enough momentum will be created that the industrial automation market will in due course face an architecture disruption empowered by these new trends. This thesis examines the current state of industrial automation subject to the competition between the incumbents firstly through a research on cost competitiveness efforts in captive outsourcing of engineering, research and development and secondly researching process re- engineering in the case of complex system global software support. Thirdly we investigate the industry actors', namely customers, incumbents and newcomers, views on the future direction of industrial automation and conclude with our assessments of the possible routes industrial automation could advance taking into account the looming rise of the Internet of Things (loT) and weightless networks. Industrial automation is an industry dominated by a handful of global players each of them focusing on maintaining their own proprietary solutions. The rise of de facto standards like IBM PC, Unix and Linux and SoC leveraged by IBM, Compaq, Dell, HP, ARM, Apple, Google, Samsung and others have created new markets of personal computers, smartphone and tablets and will eventually also impact industrial automation through game changing commoditization and related control point and business model changes. This trend will inevitably continue, but the transition to a commoditized industrial automation will not happen in the near future.

Diseño e implementación de una Web dinámica como herramienta para el control de obras en base al coste del proceso de construcción

En la actualidad estamos sufriendo una situación de crisis económica de dimensiones desproporcionadas e inusuales, la cual está obligando a todas las empresas a globalizar en mayor medida el ámbito de actuación de sus negocios, por lo que muchas empresas que trabajaban exclusivamente en el ámbito local o nacional han tenido que expandirse hacia el exterior. Este hecho, añadido a la fortísima competencia existente en el mercado, obligará a todas estas empresas a tener que controlar en mayor medida la actividad productiva, y a hacerlo utilizando tecnologías que faciliten el flujo de la información dentro de la empresa, hagan que la distancia no sea un problema para la transmisión de esa información, y con las que todos los usuarios manejen los mismos datos. El sector de la construcción es uno de los más castigados por la citada crisis, y probablemente uno de los más retrasados en lo que respecta a utilización de Tecnologías de la Información y la Comunicación. El objetivo principal de este trabajo es el diseño e implementación de una web dinámica como herramienta para medir la eficiencia en el control de la actividad productiva de una empresa constructora. La manera de medir esta eficiencia será mediante la comparación mensual de los costes previstos para las diferentes obras que deba ejecutar la empresa (los cuales podemos llamar estándar) y los que se vayan produciendo realmente. La herramienta diseñada podría ir aumentando su utilidad si, añadiendo módulos mediante la ampliación de la base de datos y diseñando las pertinentes nuevas páginas web para el sitio, se usa también para otros menesteres además del control de la actividad productiva por comparación entre costes previstos y reales. Es decir, que se podría llegar a gestionar la información de todas las actividades de la empresa (compras, recursos humanos, contabilidad, gestión de calidad, etc.). Por lo tanto, una web dinámica como la expuesta en el trabajo podría servir como semilla para el desarrollo de un ERP (Enterprise Resource Planning).

Disseny d'un sistema de control del consum d'aigua automàtic

Avui en dia s’ha convertit en una necessitat tenir cura del medi ambient i optimitzar els recursos naturals. En el camp per estalviar energia s’han fet grans progressos i disposem d’un gran ventall de dispositius que ens ajuden i ens faciliten l’optimització del consum d’energia. Però és una realitat que en l’estalvi del consum d’aigua el progrés ha estat molt menor i es limita molt a donar consells i repartir dosificadors d’aigua. Qui no ha vist carrers o jardins o cases inundades amb milers de litres d’aigua? Aquesta realitat m’ha portat a dissenyar i desenvolupar un prototip que em permeti tenir un millor control del consum d’aigua. El prototip, a trets principals, consta d’un sensor, una electrovàlvula i una placa Arduino Atmega. El sensor ens permet mesurar els litres consumits durant un cert període de temps. Passat aquest temps de mostreig es compara els litres consumits amb el consum habitual, en aquell període de temps. En cas de sobrepassar el volum programat es tancarà l’electrovàlvula de forma automàtica i rebrem un SMS al telèfon. L’activació de l’alarma es pot ajustar que sigui al igualar-se els dos valors, litres programats i litres consumits. També es pot programar el percentatge que cal sobrepassar de litres consumits per activar l’alarma, com el temps de mostreig. El fet de poder programar tots aquests valors ens permet fer un ajust ideal per a la instal·lació que es vol tenir controlada. A més, el prototip es pot utilitzar per enviar a la companyia d’aigua el valor del comptador de forma automàtica. D’aquesta forma la companyia d’aigua també optimitza recursos estalviant-se el desplaçament de personal a la instal·lació per fer la lectura corresponent. El prototip està basat amb un Arduino Atmega que ens permet el processament de les dades programades i capturades pel sensor. També s’ha incorporat una pantalla TFT Touch 2’8”, que permet visualitzar i programar els valors d’una forma molt més intuïtiva. Per enviar els SMS s’utilitza una placa d’Arduino Cel·lular Shield - SM5100B, a la qual només cal afegir una targeta SIM. A priori, el prototip té un elevat cost al fabricar una sola unitat i pot semblar poc útil. Però ens pot estalviar alguna sorpresa en les factures d’aigua si tenim una fuita i no ens n’adonem fins a veure el rebut de la companyia. Si es fabriqués a grans quantitats es podria abaratir el preu i fer-lo encara més engrescador.

Control de producció de màquines flexogràfiques

Control de producció de maquinària industrial del sector de les arts gràfiques, concretament d'impressores flexogràfiques.

Industrial nanoparticle application : representative survey among Swiss companies shows low usage and basic protection means

Manufactured nanoparticles are introduced into industrial processes, but they are suspected to cause similar negative health effects as ambient particles. The poor knowledge about the scale of this introduction did not allow global risk analysis so far. In 2006 a targeted telephone survey among Swiss companies (1) showed the usage of nanoparticles in a few selected companies but did not provide data to extrapolate on the totality of the Swiss workforce. To gain this kind of information a layered representative questionnaire survey among 1'626 Swiss companies was conducted in 2007. Data was collected about the number of potentially exposed persons in the companies and their protection strategy. The response rate was 58.3%. An expected number of 586 companies (95%−confidence interval 145 to 1'027) was shown by this study to use nanoparticles in Switzerland. Estimated 1'309 (1'073 to 1'545) workers do their job in the same room as a nanoparticle application. Personal protection was shown to be the predominant type of protection means. Companies starting productions with nanomaterials need to consider incorporating protection measures into the plans. This will not only benefit the workers' health, but will also likely increase the competitiveness of the companies. Technical and organisational protection means are not only more cost−effective on the long term, but are also easier to control. Guidelines may have to be designed specifically for different industrial applications, including fields outside nanotechnology, and adapted to all sizes of companies.

Aplicació de verificació i control de codi de barres i datamatrix

A les línies de producció de l’empresa Laboratorios Hipra, s’ha plantejat imprimir els codis de les caixes mitjançant nous làsers amb la tècnica de delineat làser, amb aquests nous models de làser es vol imprimir codis datamatrix. Per tal que això sigui possible, és molt important poder tenir un control de les impressions realitzades pel làser, ja que en cas contrari, podrien empaquetar-se caixes amb un marcatge erroni. S’ha dissenyatuna aplicació capaç de verificar i controlar les impressions realitzades pels làsers. Aquesta aplicació ha de ser capaç de verificar i controlar les caixes marcades tant amb codis de barres com amb datamatrix, a més a més de mostrar totes les dades dels marcatges per una pantalla SCADA. L’aplicació també incorpora un sistema d’expulsió de les caixes amb un marcatge d’inferior qualitat a la desitjada en cada moment

Control hardware and Condition Monitoring System for Intersector Weld/Cut Robot

Työ sisältää ohjaislaitteiston vertailun ja valinnan rinnakkaisrakenteista robottia varten sekä kunnonvalvontajärjestelmän periaatteiden laadinnan kyseistä robottia varten. Ohjauslaitteisto sisältää teollisuustietokoneen sekä kenttäväylän. Sekä tietokoneesta että väylästä on teoriaosuus ja yksityiskohtaisempi valintaosuus. Teoriaosuudessa selitetään tarkemmin laitteiden toimintaperiaatteista. Valintaosuudessa kerrotaanmiksi jokin tietty laite on valittu käytettäväksi robotin ohjauksessa. Kunnonvalvontateoria ja rinnakkaisrakenteisen robotin kunnonvalvonnan keinot ovat työn toinen osa. Teoriaosa sisältää yleisluonteisen selvityksen vikaantumisesta ja valvonnasta. Erikoisrobotin kunnonvalvonnan keinot esitetään työssä tietyssä järjestyksessä. Ensin esitetään mahdolliset vikatilanteet. Toisessa kohdassa havainnollistetaan vikojen havaitseminen.

Disseny d'una nau bioclimàtica sense ús determinat, ubicat al Polígon Industrial "Camí dels Frares" de Lleida

L'objecte del present projecte tècnic és la descripció de la climatització d'una nau industrial bioclimàtica, fent ús de sistemes passius i si fos necessari, de sistemes actius. El concepte de bioclimàtic procedeix de bios-vida i clima - orientació. El propòsit d'aquest disseny arquitectònic és que des del punt de vista energètic permeti que la nau mantingui un nivell de confort tant en hivern com en estiu, aplicant una sèrie de criteris de disseny a fi d'utilitzar els elements constructius i funcionals propis de l'edifici per tal d'aconseguir un bon control del seu comportament energètic.

Equip per a la recuperació de fluids d'un automòbil

El projecte defineix un equip per a l'extracció de fluids d'un vehicle fora d'ús. Aquest extreu per separat els combustibles, els olis, el líquid de frens i l'anticongelant. El sistema d'extracció es realitza per una bomba de buit, a partir del buit creat en un calderí hi entra el líquid corresponent per diferència de pressió i conduint els líquids als dipòsits d'emmagatzematge. L'equip consta d'un conjunt de conductes, vàlvules, filtres i sensors i també inclou un autòmat pel seu control automàtic.

FPGA-Based Control Design for Power Electronic Applications

Tehoelektoniikkalaitteella tarkoitetaan ohjaus- ja säätöjärjestelmää, jolla sähköä muokataan saatavilla olevasta muodosta haluttuun uuteen muotoon ja samalla hallitaan sähköisen tehon virtausta lähteestä käyttökohteeseen. Tämä siis eroaa signaalielektroniikasta, jossa sähköllä tyypillisesti siirretään tietoa hyödyntäen eri tiloja. Tehoelektroniikkalaitteita vertailtaessa katsotaan yleensä niiden luotettavuutta, kokoa, tehokkuutta, säätötarkkuutta ja tietysti hintaa. Tyypillisiä tehoelektroniikkalaitteita ovat taajuudenmuuttajat, UPS (Uninterruptible Power Supply) -laitteet, hitsauskoneet, induktiokuumentimet sekä erilaiset teholähteet. Perinteisesti näiden laitteiden ohjaus toteutetaan käyttäen mikroprosessoreja, ASIC- (Application Specific Integrated Circuit) tai IC (Intergrated Circuit) -piirejä sekä analogisia säätimiä. Tässä tutkimuksessa on analysoitu FPGA (Field Programmable Gate Array) -piirien soveltuvuutta tehoelektroniikan ohjaukseen. FPGA-piirien rakenne muodostuu erilaisista loogisista elementeistä ja niiden välisistä yhdysjohdoista.Loogiset elementit ovat porttipiirejä ja kiikkuja. Yhdysjohdot ja loogiset elementit ovat piirissä kiinteitä eikä koostumusta tai lukumäärää voi jälkikäteen muuttaa. Ohjelmoitavuus syntyy elementtien välisistä liitännöistä. Piirissä on lukuisia, jopa miljoonia kytkimiä, joiden asento voidaan asettaa. Siten piirin peruselementeistä voidaan muodostaa lukematon määrä erilaisia toiminnallisia kokonaisuuksia. FPGA-piirejä on pitkään käytetty kommunikointialan tuotteissa ja siksi niiden kehitys on viime vuosina ollut nopeaa. Samalla hinnat ovat pudonneet. Tästä johtuen FPGA-piiristä on tullut kiinnostava vaihtoehto myös tehoelektroniikkalaitteiden ohjaukseen. Väitöstyössä FPGA-piirien käytön soveltuvuutta on tutkittu käyttäen kahta vaativaa ja erilaista käytännön tehoelektroniikkalaitetta: taajuudenmuuttajaa ja hitsauskonetta. Molempiin testikohteisiin rakennettiin alan suomalaisten teollisuusyritysten kanssa soveltuvat prototyypit,joiden ohjauselektroniikka muutettiin FPGA-pohjaiseksi. Lisäksi kehitettiin tätä uutta tekniikkaa hyödyntävät uudentyyppiset ohjausmenetelmät. Prototyyppien toimivuutta verrattiin vastaaviin perinteisillä menetelmillä ohjattuihin kaupallisiin tuotteisiin ja havaittiin FPGA-piirien mahdollistaman rinnakkaisen laskennantuomat edut molempien tehoelektroniikkalaitteiden toimivuudessa. Työssä on myösesitetty uusia menetelmiä ja työkaluja FPGA-pohjaisen säätöjärjestelmän kehitykseen ja testaukseen. Esitetyillä menetelmillä tuotteiden kehitys saadaan mahdollisimman nopeaksi ja tehokkaaksi. Lisäksi työssä on kehitetty FPGA:n sisäinen ohjaus- ja kommunikointiväylärakenne, joka palvelee tehoelektroniikkalaitteiden ohjaussovelluksia. Uusi kommunikointirakenne edistää lisäksi jo tehtyjen osajärjestelmien uudelleen käytettävyyttä tulevissa sovelluksissa ja tuotesukupolvissa.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Permanent magnet synchronous motor for industrial inverter applications - analysis and design

During the latest few years the need for new motor types has grown, since both high efficiency and an accurate dynamic performance are demanded in industrial applications. For this reason, new effective control systems such as direct torque control (DTC) have been developed. Permanent magnet synchronous motors (PMSM) are well suitable for new adjustable speed AC inverter drives, because their efficiency and power factor are not depending on the pole pair number and speed to the same extent as it is the case in induction motors. Therefore, an induction motor (IM) with a mechanical gearbox can often be replaced with a direct PM motor drive. Space as well as costs will be saved, because the efficiency increases and the cost of maintenance decreases as well. This thesis deals with design criterion, analytical calculation and analysis of the permanent magnet synchronous motor for both sinusoidal air-gap flux density and rectangular air-gapflux density. It is examined how the air-gap flux, flux densities, inductances and torque can be estimated analytically for salient pole and non-salient pole motors. It has been sought by means of analytical calculations for the ultimate construction for machines rotating at relative low 300 rpm to 600 rpm speeds, which are suitable speeds e.g. in Pulp&Paper industry. The calculations are verified by using Finite Element calculations and by measuring of prototype motor. The prototype motor is a 45 kW, 600 rpm PMSM with buried V-magnets, which is a very appropriate construction for high torque motors with a high performance. With the purposebuilt prototype machine it is possible not only to verify the analytical calculations but also to show whether the 600 rpm PMSM can replace the 1500 rpm IM with a gear. It can also be tested if the outer dimensions of the PMSM may be the same as for the IM and if the PMSM in this case can produce a 2.5 fold torque, in consequence of which it may be possible to achieve the same power. The thesis also considers the question how to design a permanent magnet synchronous motor for relatively low speed applications that require a high motor torqueand efficiency as well as bearable costs of permanent magnet materials. It is shown how a selection of different parameters affects the motor properties. Key words: Permanent magnet synchronous motor, PMSM, surface magnets, buried magnets

Induction motor versus permanent magnet synchronous motor in motion control applications: a comparative study

High dynamic performance of an electric motor is a fundamental prerequisite in motion control applications, also known as servo drives. Recent developments in the field of microprocessors and power electronics have enabled faster and faster movements with an electric motor. In such a dynamically demanding application, the dimensioning of the motor differs substantially from the industrial motor design, where feasible characteristics of the motor are for example high efficiency, a high power factor, and a low price. In motion control instead, such characteristics as high overloading capability, high-speed operation, high torque density and low inertia are required. The thesis investigates how the dimensioning of a high-performance servomotor differs from the dimensioning of industrial motors. The two most common servomotor types are examined; an induction motor and apermanent magnet synchronous motor. The suitability of these two motor types indynamically demanding servo applications is assessed, and the design aspects that optimize the servo characteristics of the motors are analyzed. Operating characteristics of a high performance motor are studied, and some methods for improvements are suggested. The main focus is on the induction machine, which is frequently compared to the permanent magnet synchronous motor. A 4 kW prototype induction motor was designed and manufactured for the verification of the simulation results in the laboratory conditions. Also a dynamic simulation model for estimating the thermal behaviour of the induction motor in servo applications was constructed. The accuracy of the model was improved by coupling it with the electromagnetic motor model in order to take into account the variations in the motor electromagnetic characteristics due to the temperature rise.