Human exposure to brominated flame retardants

Human polybrominated diphenyl ether (PBDE) exposure occurs through a range of pathways including: ingestion of dust including hand-to-mouth contact; inhalation (air/particulate matter); and ingestion via food including the unique nutrition sources of human milk and placental transfer. While inhalation has been deemed a minor source of exposure, ingestion of food and dust make greater contributions to overall PBDE body burden with intake via dust reported to be much higher in infants than in adults. PBDEs have been detected in samples of human milk, blood serum, cord blood, and adipose tissue worldwide. Concentrations have been found to be highest in populations from North America, followed by Australia, Europe, and Asia. While factors such as gender and parity may not affect concentrations, occupational exposure and age (infants and children) are associated with higher PBDE concentrations. In contrast to “traditional” persistent organic pollutants, there is an inverse relationship between PBDE body burden and age. Predicted body burden calculated using available information on intake and elimination rates of BFRs appears to underestimate measured human body burden data obtained through analysis of BFRs in blood or human milk. This may be due to unknown exposure or inaccurate elimination data. Further exposure studies should focus on younger age groups and an investigation of human PBDE half-lives.

Characterisation of the micro-architecture of direct writing melt electrospun tissue engineering scaffolds using diffusion tensor and computed tomography microimaging

This article describes the first steps toward comprehensive characterization of molecular transport within scaffolds for tissue engineering. The scaffolds were fabricated using a novel melt electrospinning technique capable of constructing 3D lattices of layered polymer fibers with well - defined internal microarchitectures. The general morphology and structure order was then determined using T 2 - weighted magnetic resonance imaging and X - ray microcomputed tomography. Diffusion tensor microimaging was used to measure the time - dependent diffusivity and diffusion anisotropy within the scaffolds. The measured diffusion tensors were anisotropic and consistent with the cross - hatched geometry of the scaffolds: diffusion was least restricted in the direction perpendicular to the fiber layers. The results demonstrate that the cross - hatched scaffold structure preferentially promotes molecular transport vertically through the layers ( z - axis), with more restricted diffusion in the directions of the fiber layers ( x – y plane). Diffusivity in the x – y plane was observed to be invariant to the fiber thickness. The characteristic pore size of the fiber scaffolds can be probed by sampling the diffusion tensor at multiple diffusion times. Prospective application of diffusion tensor imaging for the real - time monitoring of tissue maturation and nutrient transport pathways within tissue engineering scaffolds is discussed.

Ion-assisted precursor dissociation and surface diffusion : enabling rapid, low-temperature growth of carbon nanofibers

Growth kinetics of carbon nanofibers in a hydrocarbon plasma is studied. In addition to gas-phase and surface processes common to chemical vapor deposition, the model includes (unique to plasma-exposed catalyst surfaces) ion-induced dissociation of hydrocarbons, interaction of adsorbed species with incoming hydrogen atoms, and dissociation of hydrocarbon ions. It is shown that at low, nanodevice-friendly process temperatures the nanofibers grow via surface diffusion of carbon adatoms produced on the catalyst particle via ion-induced dissociation of a hydrocarbon precursor. These results explain a lower activation energy of nanofiber growth in a plasma and can be used for the synthesis of other nanoassemblies. © 2007 American Institute of Physics.

Low-pressure diffusion equilibrium of electronegative complex plasmas

A model for electronegative plasmas containing charged dust or colloidal grains was used. Numerical solutions based on the model demonstrate how a low-pressure diffusion equilibrium of the complex electronegative plasma system is dynamically sustained through plasma particle sources.

Comparison of block and event-related experimental designs in diffusion-weighted functional MRI

PURPOSE To compare diffusion-weighted functional magnetic resonance imaging (DfMRI), a novel alternative to the blood oxygenation level-dependent (BOLD) contrast, in a functional MRI experiment. MATERIALS AND METHODS Nine participants viewed contrast reversing (7.5 Hz) black-and-white checkerboard stimuli using block and event-related paradigms. DfMRI (b = 1800 mm/s2 ) and BOLD sequences were acquired. Four parameters describing the observed signal were assessed: percent signal change, spatial extent of the activation, the Euclidean distance between peak voxel locations, and the time-to-peak of the best fitting impulse response for different paradigms and sequences. RESULTS The BOLD conditions showed a higher percent signal change relative to DfMRI; however, event-related DfMRI showed the strongest group activation (t = 21.23, P < 0.0005). Activation was more diffuse and spatially closer to the BOLD response for DfMRI when the block design was used. DfMRIevent showed the shortest TTP (4.4 +/- 0.88 sec). CONCLUSION The hemodynamic contribution to DfMRI may increase with the use of block designs.

Building macroscale models from microscale probabilistic models : a general probabilistic approach for nonlinear diffusion and multispecies phenomena

A discrete agent-based model on a periodic lattice of arbitrary dimension is considered. Agents move to nearest-neighbor sites by a motility mechanism accounting for general interactions, which may include volume exclusion. The partial differential equation describing the average occupancy of the agent population is derived systematically. A diffusion equation arises for all types of interactions and is nonlinear except for the simplest interactions. In addition, multiple species of interacting subpopulations give rise to an advection-diffusion equation for each subpopulation. This work extends and generalizes previous specific results, providing a construction method for determining the transport coefficients in terms of a single conditional transition probability, which depends on the occupancy of sites in an influence region. These coefficients characterize the diffusion of agents in a crowded environment in biological and physical processes.

Enterprise resource planning or enterprise resource plotting? Technological, organisational and inter-organisational aspects of enterprise resource planning package adoption and diffusion

Those in organisations tend to adopt new technologies as a way to improve their functions, reduce cost and attain best practices. Thus, technology promoters (or vendors) work along those lines in order to convince adopters to invest in those technologies and develop their own organisations profit in return. The possible resultant ‘conflicts of interest’ makes the study of reasons behind IT diffusion and adoption an interesting subject. In this paper we look at IT diffusion and adoption in terms of technology (system features), organisational aspects (firm level characteristics) and inter-organisational aspects (market dynamics) in order to see who might be the real beneficiaries of technology adoption. We use ERP packages as an example of an innovation that has been widely diffused and adopted for the last 10 years. We believe that our findings can be useful to those adopting ERP packages as it gives them a wider view of the situation.

Milling and diffusion extraction : theory and practice

AN ENGINEERING Workshop was held from 21 to 24 November 2006 in Veracruz, Mexico. Forty delegates from 12 countries attended the workshop on theory and practice of milling and diffusion extraction. This report provides a general overview of activities undertaken during that workshop which consisted of five technical sessions over two days with presentations and discussions plus two days of field and factory visits. Topics covered during the technical sessions included: power transmissions, cane preparation, diffusers, mills, and a comparison of milling and diffusion.