Comparing detection and location performance of perpendicular and parallel broadside GPR antenna orientations

GPR (Ground Penetrating Radar) results are shown for perpendicular broadside and parallel broadside antenna orientations. Performance in detection and localization of concrete tubes and steel tanks is compared as a function of acquisition configuration. The comparison is done using 100 MHz and 200 MHz center frequency antennas. All tubes and tanks are buried at the geophysical test site of IAG/USP in Sao Paulo city, Brazil. The results show that the long steel pipe with a 38-mm diameter was well detected with the perpendicular broadside configuration. The concrete tubes were better detected with the parallel broadside configuration, clearly showing hyperbolic diffraction events from all targets up to 2-m depth. Steel tanks were detected with the two configurations. However, the parallel broadside configuration was generated to a much lesser extent an apparent hyperbolic reflection corresponding to constructive interference of diffraction hyperbolas of adjacent targets placed at the same depth. Vertical concrete tubes and steel tanks were better contained with parallel broadside antennas, where the apexes of the diffraction hyperbolas better corresponded to the horizontal location of the buried target disposition. The two configurations provide details about buried targets emphasizing how GPR multi-component configurations have the potential to improve the subsurface image quality as well as to discriminate different buried targets. It is judged that they hold some applicability in geotechnical and geoscientific studies. (C) 2009 Elsevier B.V. All rights reserved.

Efeito da inclinação do plano de terra para antenas de microfita multicamadas com elementos parasitas fractais

This work presents the analysis of an antenna of fractal microstrip of Koch with dielectric multilayers and inclinations in the ground plane, whose values of the angles are zero degree (without inclinations), three, seven and twelve degrees. This antenna consists of three dielectric layers arranged vertically on each other, using feeding microstrip line in patch 1, of the first layer, which will feed the remaining patches of the upper layers by electromagnetic coupling. The objective of this work is to analyze the effects caused by increase of the angle of inclination of the ground plane in some antenna parameters such as return loss, resonant frequency, bandwidth and radiation pattern. The presented results demonstrate that with the increase of the inclination angle it is possible to get antennas with characteristics multiband, with bigger bandwidth, and improving the impedance matching for each case analyzed, especially the larger angle

Caracterização de superfícies seletivas de freqüência e de antenas fractais para aplicações em redes sem fio

This work aims to investigate the behavior of fractal elements in planar microstrip structures. In particular, microstrip antennas and frequency selective surfaces (FSSs) had changed its conventional elements to fractal shapes. For microstrip antennas, was used as the radiating element of Minkowski fractal. The feeding method used was microstrip line. Some prototypes were built and the analysis revealed the possibility of miniaturization of structures, besides the multiband behavior, provided by the fractal element. In particular, the Minkowski fractal antenna level 3 was used to exploit the multiband feature, enabling simultaneous operation of two commercial tracks (Wi-Fi and WiMAX) regulated by ANATEL. After, we investigated the effect of switches that have been placed on the at the pre-fractal edges of radiating element. For the FSSs, the fractal used to elements of FSSs was Dürer s pentagon. Some prototypes were built and measured. The results showed a multiband behavior of the structure provided by fractal geometry. Then, a parametric analysis allowed the analysis of the variation of periodicity on the electromagnetic behavior of FSS, and its bandwidth and quality factor. For numerical and experimental characterization of the structures discussed was used, respectively, the commercial software Ansoft DesignerTM and a vector network analyzer, Agilent N5230A model

Análise e projeto de superfícies seletivas em frequência multibanda e/ou banda larga

Frequency selective surfaces (Frequency Selective Surface - FSS) are often used in various applications in telecommunications. Some of these applications may require that these structures have response with multiple resonance bands. Other applications require that the FSS response have large frequency range, to meet the necessary requirements. FSS to design with these features there are numerous techniques cited in the scientific literature. Thus, the purpose of this paper is to examine some common techniques such as: Overlap of FSS; Elements combined; Elements Elements convolucionados and fractals. And designing multiband FSS and / or broadband selecting simple ways in terms of construction and occupy the smallest possible space, aiming at practical applications. Given these requirements, three projects FSS were performed: a technology applied to IEEE 802.11 a/b/g/n and two projects for application in UWB. In project development, commercial software Ansoft DesignerTM and experimental results were satisfactory was used

Projeto de antenas multibandas integradas para terminais 4G

O presente trabalho apresenta um projeto e análise de uma antena monopolo planar multibanda operante nas frequências de 2000 MHz, 2500 MHz e 3500 MHz para aplicação em dispositivos móveis 3G e 4G. Dentre essas faixas estão contidos os espectros 3G (1895- 2165 MHz), 4G (2500-2690 MHz) e 4G (3400-3600 MHz) utilizadas pelo LTE e WIMAX 3,5. Para o desenvolvimento desse estudo foi tomado como referência uma antena dual-band de Hua- Ming Chen projetada para operar em sistemas ISM 1800 MHz, redes Wireless e Bluetooth 2400 MHz. O projeto proposto neste trabalho é uma modificação na estrutura da antena dual-band adaptada para tripla ressonância simultânea em frequências utilizadas em redes móveis 4G. Para alcançar o objetivo proposto utilizou-se para simulação o software CST® MICROWAVE STUDIO baseado no método Integração Finita no Domínio, as simulações foram feitas no domínio do tempo. Após obtenção satisfatória dos resultados simulados, um protótipo da antena foi confeccionado para medição e teste, os resultados apresentados são coerentes aos obtidos na simulação, o que valida o método proposto.

Parametric study of retangular patch antenna using denim textile material

—This paper presents a textile patch antenna designed for WBAN applications at 2.45 GHz ISM band. The antenna uses denim as substrate and conductive fabric for the ground plane and radiator layers. The main purpose of this paper is to analyze the influence of typical deviation of denim properties and patch radiator dimensions on the performance of the antenna. The parameters considered in the analysis are the relative permittivity and thickness of denim and the width and length of the rectangular patch radiator. The dependence of the central operation frequency of the antenna on those parameters was studied using the antenna reflection coefficient obtained from EM simulations. Rules of thumb for one-shot design were derived and applied to design a rectangular patch antenna. An antenna prototype was fabricated and measured, demonstrating a 10 dB impedance band of 4.8 % centered at 2.45 GHz, in good agreement with simulated results

A complete CMOS UWB timed-array transmitter with a 3D Vivaldi antenna array for electronic high-resolution beam spatial scanning

We present a new Ultra Wide Band (UWB) Timed- Array Transmitter System with Beamforming capability for high-resolution remote acquisition of vital signals. The system consists of four identical channels, where each is formed of a serial topology with three modules: programmable delay circuit (PDC or τ), a novel UWB 5th Gaussian Derivative order pulse generator circuit (PG), and a planar Vivaldi antenna. The circuit was designed using 0.18μm CMOS standard process and the planar antenna array was designed with filmconductor on Rogers RO3206 substrate. Spice simulations results showed the pulse generation with 104 mVpp amplitude and 500 ps width. The power consumption is 543 μW, and energy consumption 0.27 pJ per pulse using a 2V power supply at a pulse repetition rate (PRR) of 100 MHz. Electromagnetic simulations results, using CST Microwave (MW) Studio 2011, showed the main lobe radiation with a gain maximum of 13.2 dB, 35.5º x 36.7º angular width, and a beam steering between 17º and -11º for azimuthal (θ) angles and 17º and -18º for elevation (φ) angles at the center frequency of 6 GHz

Diseño de un LNA multibanda integrado con carga sintonizable y adaptación de entrada de banda ancha

Proyecto y presentación del Proyecto Fin de Carrera titulado "Diseño de un LNA multibanda integrado con carga sintonizable y adaptación de entrada de banda ancha"

Sea level measurement using single GNSS antenna SNR signals

This thesis presents a possible method to calculate sea level variation using geodetic-quality Global Navigate Satellite System (GNSS) receivers. Three antennas are used: two small antennas and a choke ring one, analyzing only Global Positioning System signals. The main goal of the thesis is to test a modified configuration for antenna set up. In particular, measurements obtained tilting one antenna to face the horizon are compared to measurements obtained from antennas looking upward. The location of the experiment is a coastal environment nearby the Onsala Space Observatory in Sweden. Sea level variations are obtained using periodogram analysis of the SNR signal and compared to synthetic gauge generated from two independent tide gauges. The choke ring antenna provides poor result, with an RMS around 6 cm and a correlation coefficients of 0.89. The smaller antennas provide correlation coefficients around 0.93. The antenna pointing upward present an RMS of 4.3 cm and the one pointing the horizon an RMS of 6.7 cm. Notable variation in the statistical parameters is found when modifying the length of the interval analyzed. In particular, doubts are risen on the reliability of certain scattered data. No relation is found between the accuracy of the method and weather conditions. Possible methods to enhance the available data are investigated, and correlation coefficient above 0.97 can be obtained with small antennas when sacrificing data points. Hence, the results provide evidence of the suitability of SNR signal analysis for sea level variation in coastal environment even in the case of adverse weather conditions. In particular, tilted configurations provides comparable result with upward looking geodetic antennas. A SNR signal simulator is also tested to investigate its performance and usability. Various configuration are analyzed in combination with the periodogram procedure used to calculate the height of reflectors. Consistency between the data calculated and those received is found, and the overall accuracy of the height calculation program is found to be around 5 mm for input height below 5 m. The procedure is thus found to be suitable to analyze the data provided by the GNSS antennas at Onsala.

Approccio teorico e numerico per la selezione di topologie d'antenna miniaturizzate su substrati magneto-dielettrici

Lo sviluppo di soluzioni sempre più pervasive, nell’ambito delle telecomunicazioni, ha determinato una necessità crescente di avere sistemi wireless con dimensioni estremamente ridotte. Tale obiettivo deve essere raggiunto evitando di incorrere nelle problematiche in termini di prestazioni di radiazione che si presentano utilizzando antenne dalle dimensioni molto ridotte rispetto la lunghezza d'onda. Tali inefficienze finiscono poi per ripercuotersi sulle funzionalità, ma sopratutto sul consumo energetico e quindi sulla sua autonomia. Nell’ambito di questa tesi, ci si è focalizzati sui materiali e in particolare su come possono essere selezionati in base alle caratteristiche delle varie topologie di antenne, con lo scopo di massimizzare le caratteristiche prestazionali dell'elemento radiante. Sarà inoltre presentata una definizione innovativa e dedicata ai materiali magneto-dielettrici del volume di campo vicino. Si concluderà infine che, nel caso di antenne rappresentate da sorgenti equivalenti magnetiche è conveniente usare materiali magnetici, mentre con sorgenti equivalenti elettriche il solo dielettrico risulta più indicato.

RFID tag localization with virtual multi-antenna systems

In questa tesi si sono valutate le prestazioni di un sistema di localizzazione multi-antenna di tag radio frequency identification (RFID) passivi in ambiente indoor. Il sistema, composto da un reader in movimento che percorre una traiettoria nota, ha come obiettivo localizzare il tag attraverso misure di fase; più precisamente la differenza di fase tra il segnale di interrogazione, emesso dal reader, e il segnale ricevuto riflesso dal tag che è correlato alla distanza tra di essi. Dopo avere eseguito una ricerca sullo stato dell’arte di queste tecniche e aver derivato il criterio maximum likelihood (ML) del sistema si è proceduto a valutarne le prestazioni e come eventuali fattori agissero sul risultato di localizzazione attraverso simulazioni Matlab. Come ultimo passo si è proceduto a effettuare una campagna di misure, testando il sistema in un ambiente reale. Si sono confrontati i risultati di localizzazione di tutti gli algoritmi proposti quando il reader si muove su una traiettoria rettilinea e su una traiettoria angolare, cercando di capire come migliorare i risultati.

Localizzazione e tracking tramite filtri statistici in sistemi multi antenna

Uno dei temi più recenti nel campo delle telecomunicazioni è l'IoT. Tale termine viene utilizzato per rappresentare uno scenario nel quale non solo le persone, con i propri dispositivi personali, ma anche gli oggetti che le circondano saranno connessi alla rete con lo scopo di scambiarsi informazioni di diversa natura. Il numero sempre più crescente di dispositivi connessi in rete, porterà ad una richiesta maggiore in termini di capacità di canale e velocità di trasmissione. La risposta tecnologica a tali esigenze sarà data dall’avvento del 5G, le cui tecnologie chiave saranno: massive MIMO, small cells e l'utilizzo di onde millimetriche. Nel corso del tempo la crescita delle vendite di smartphone e di dispositivi mobili in grado di sfruttare la localizzazione per ottenere servizi, ha fatto sì che la ricerca in questo campo aumentasse esponenzialmente. L'informazione sulla posizione viene utilizzata infatti in differenti ambiti, si passa dalla tradizionale navigazione verso la meta desiderata al geomarketing, dai servizi legati alle chiamate di emergenza a quelli di logistica indoor per industrie. Data quindi l'importanza del processo di positioning, l'obiettivo di questa tesi è quello di ottenere la stima sulla posizione e sulla traiettoria percorsa da un utente che si muove in un ambiente indoor, sfruttando l'infrastruttura dedicata alla comunicazione che verrà a crearsi con l'avvento del 5G, permettendo quindi un abbattimento dei costi. Per fare ciò è stato implementato un algoritmo basato sui filtri EKF, nel quale il sistema analizzato presenta in ricezione un array di antenne, mentre in trasmissione è stato effettuato un confronto tra due casi: singola antenna ed array. Lo studio di entrambe le situazioni permette di evidenziare, quindi, i vantaggi ottenuti dall’utilizzo di sistemi multi antenna. Inoltre sono stati analizzati altri elementi chiave che determinano la precisione, quali geometria del sistema, posizionamento del ricevitore e frequenza operativa.