Avaliação dos efeitos do implante de silicone sobre o parênquima mamário e a musculatura peitoral maior

A mamoplastia de aumento está associada a alto grau de satisfação e significativa melhora da qualidade de vida das pacientes. Apesar disso, uma das principais causas de reoperação após esse procedimento se refere a deformidades de contorno e questões volumétricas. Ainda existem poucos dados objetivos para análise volumétrica pós-operatória da mamoplastia de aumento. O parênquima mamário sofre alterações microvasculares quando sob compressão mecânica, porém o tecido muscular é mais suscetível à lesão quando submetido a pressão do que outros tecidos, tendo pouca tolerância à compressão mecânica. O objetivo deste estudo é avaliar e comparar as alterações no parênquima mamário na mamoplastia de aumento subglandular e submuscular, além de avaliar as alterações volumétricas e funcionais da musculatura peitoral após a inserção de implantes no plano submuscular. Cinquenta e oito pacientes do sexo feminino foram randomizadas em dois grupos de estudo, com 24 pacientes cada, e um grupo controle com dez pacientes, de acordo com critérios de inclusão e não inclusão. Das pacientes do grupo de estudo, 24 foram submetidas à mamoplastia de aumento com inserção de implantes no plano suglandular e 24 foram submetidas ao procedimento no plano submuscular. As pacientes do grupo subglandular realizaram análise volumétrica da glândula mamária e as pacientes dos grupos submuscular e controle, além da volumetria mamária, também realizaram volumetria do músculo peitoral maior. A avaliação volumétrica foi realizada no pré-operatório e no pós-operatório, aos seis e 12 meses, por meio de ressonância magnética. Apenas as pacientes do grupo submuscular foram submetidas à avaliação da força muscular, com a utilização de teste isocinético, no pré-operatório e no pós-operatório, aos três, seis e 12 meses. Todas as pacientes estavam sob uso de anticoncepcional oral de baixa dosagem e as pacientes do grupo submuscular permaneceram afastadas de atividades físicas por um período de dois meses no pós-operatório. O grupo subglandular apresentou 22,8% de atrofia da glândula mamária ao final dos 12 meses, enquanto que o grupo submuscular não apresentou atrofia glandular ao final de um ano. O grupo submuscular apresentou atrofia muscular de 49,80% e redução da força muscular em adução após um ano de estudo. Não se observou correlação da forca muscular com a perda volumétrica, assim como não se observou alteração de forca em abdução. Concluímos que a mamoplastia de aumento suglandular causa atrofia do parênquima mamário, enquanto que o procedimento submuscular não causa esta alteração no parênquima mamário após o período de 12 meses pós-operatórios. Em contrapartida, a mamoplastia de aumento submuscular causa atrofia do músculo peitoral maior com diminuição da força muscular em adução após 12 meses de pós-operatório, sem correlação com a alteração de volume muscular.

SiO2 coating of silver nanoparticles by photoinduced chemical vapor deposition.

Gas-phase silver nanoparticles were coated with silicon dioxide (SiO2) by photoinduced chemical vapor deposition (photo-CVD). Silver nanoparticles, produced by inert gas condensation, and a SiO2 precursor, tetraethylorthosilicate (TEOS), were exposed to vacuum ultraviolet (VUV) radiation at atmospheric pressure and varying temperatures. The VUV photons dissociate the TEOS precursor, initiating a chemical reaction that forms SiO2 coatings on the particle surfaces. Coating thicknesses were measured for a variety of operation parameters using tandem differential mobility analysis and transmission electron microscopy. The chemical composition of the particle coatings was analyzed using energy dispersive x-ray spectrometry and Fourier transform infrared spectroscopy. The highest purity films were produced at 300-400 degrees C with low flow rates of additional oxygen. The photo-CVD coating technique was shown to effectively coat nanoparticles and limit core particle agglomeration at concentrations up to 10(7) particles cm(-3).

Short-channel polymer field-effect-transistor fabrication using spin-coating-induced edge template and ink-jet printing

A method to fabricate polymer field-effect transistors with submicron channel lengths is described. A thin polymer film is spin coated on a prepatterned resist with a low resolution to create a thickness contrast in the overcoated polymer layer. After plasma and solvent etching, a submicron-sized line structure, which templates the contour of the prepattern, is obtained. A further lift-off process is applied to define source-drain electrodes of transistors. With a combination of ink-jet printing, transistors with channel length down to 400 nm have been fabricated by this method. We show that drive current density increases as expected, while the on/off current ratio 106 is achieved. © 2005 American Institute of Physics.

The elastic-plastic indentation response of a columnar thermal barrier coating

Thermal barrier coatings with a columnar microstructure are prone to erosion damage by a mechanism of surface cracking upon impact by small foreign particles. In order to explore this erosion mechanism, the elastic indentation and the elastic-plastic indentation responses of a columnar thermal barrier coating to a spherical indenter were determined by the finite element method and by analytical models. It was shown that the indentation response is intermediate between that of a homogeneous half-space and that given by an elastic-plastic mattress model (with the columns behaving as independent non-linear springs). The sensitivity of the indentation behaviour to geometry and to the material parameters was explored: the diameter of the columns, the gap width between columns, the coefficient of Coulomb friction between columns and the layer height of the thermal barrier coating. The calculations revealed that the level of induced tensile stress is sufficient to lead to cracking of the columns at a depth of about the column radius. It was also demonstrated that the underlying soft bond coat can undergo plastic indentation when the coating comprises parallel columns, but this is less likely for the more realistic case of a random arrangement of tapered columns. © 2009 Elsevier B.V.

Tin coating requirements in fish cans

Prawn, crab and clam meat were processed in experimental ca s having reduced internal tin coating of 5.6 GSM. Conventional cans having 11.2 GSM tin coating were used as control. Results showed that experimental cans behaved normally when used for canning prawns, provided the lacquer film was perfect with no exposure of metal. When there was a discontinuity in lacquer film exposing the metal blackening took place in such areas. Areas subjected to severe strains like the lock seam side and expansion rings on can ends were found to be more prone to blackening. Experimental cans were found unsuitable for canning crab meat or clam meat because in both cases the can wall as well as the contents underwent discoloration, in all cases.

Effect of laser heating temperature on coating characteristics of Stellite 6 deposited by cold spray

Laser-assisted cold spray (LCS) is a new coating and fabrication process which combines some advantages of CS: solid-state deposition, retain their initial composition and high build rate with the ability to deposit materials which are either difficult or impossible to deposit using cold spray alone. Stellite 6 powder is deposited on medium carbon steels by LCS using N 2 as carrier gas pressure. The topography, cross section thickness, structure of the coatings is examined by SEM, optical microscopy, EDX. The results show that thickness and fluctuation of coating are improved with increased deposition site temperature. Porosity of coating is affected by N 2 and deposition site temperature. In this paper, it presents optimal coating using N 2 at a pressure of 3 MPa and temperature of 450°C and deposition site temperature of 1100°C.