Massa de forragem, composição morfológica e química de capim-tanzânia sob diferentes dias de descanso e altura de resíduo pós-pastejo

The experiment was conducted at UNESP/FCAV, Jaboticabal, SP, with the objective of evaluating the influence of the rest period and height of the residue post-grazing on the dry matter mass, morphologic composition and on the chemical composition of the Tanzania-grass pre-grazing condition, under rotational grazing. The treatments consisted of the combination of two rest periods (25 and 35 days) and two residue height post-grazing (30 and 50 cm), as a complete randomized design in factorial arrangement 2 x 2, with three replications, with the grazing cycles considered as sub plots. The herbage mass of stem, leaves, dead material and the leaf: stem ratio were significantly influenced (P<0.05) by the grazing cycles. The percentage of CP in the leaf and stem and the NDF in the stem, leaf and whole plant were influenced positively (P<0.05) by the grazing cycles. It was observed that the short rest periods associated with the smallest residue height post-grazing presented the best results in terms of herbage mass and chemical characteristics of the herbage.

Digestibilidade in vitro/gás de volumosos exclusivos ou combinados avaliados pelo resíduo remanescente da digestão da matéria seca e produção de gás

Foi avaliada a digestibilidade in vitro/gás da matéria seca (MS) de quatro volumosos, exclusivos e suas combinações, na proporção de 50% na MS. Foram incubados 100 mg de amostra por tratamento, em triplicatas, em 48 h de digestão. As digestibilidades da MS e a produção de gás foram: cana-de-açúcar = 60,6%, 17,3 mL; cana-de-açúcar + silagem de milho = 63,9%, 19,6 mL; cana-de-açúcar + capim-elefante com 60 dias = 60,5%, 16,9 mL; cana-de-açúcar + capim-elefante com 180 dias = 48,6%, 14,1 mL; silagem de milho = 66,3%; silagem de milho + capim-elefante com 60 dias = 62,1%, 16,7 mL; silagem de milho + capim-elefante com 180 dias = 52,7%, 15,8 mL; capim-elefante com 60 dias = 61,5%, 16,9 mL; capim-elefante com 180 dias = 34,6%, 11,7 mL. Constatou-se que a combinação de volumosos, em alguns casos, pode diminuir a digestibilidade da MS dos volumosos de melhor qualidade.

Valor nutritivo do resíduo do processamento do caroço de algodão suplementado com levedura e avaliado em bovinos

O objetivo neste trabalho foi avaliar o consumo, a digestibilidade total e parcial da matéria seca (MS) e dos nutrientes e os parâmetros ruminais de novilhos alimentados com rações à base de resíduo do processamento do caroço de algodão (RPCA) suplementado com levedura seca de cana-de-açúcar. Foram utilizados seis novilhos Nelore canulados no rúmen e duodeno, alimentados com rações compostas de 80% RPCA e 20% concentrado, composto de milho, ureia e levedura nos níveis de 0, 20 ou 40%. O delineamento experimental adotado para análise do consumo e da digestibilidade foi em blocos casualisados e a análise dos parâmetros ruminais foi em parcela subdividida. Os consumos e a digestibilidade de nutrientes não foram influenciados pela suplementação com levedura, fato que pode estar relacionado ao alto valor da fração C do resíduo do processamento do RPCA (44,51% MS) e à baixa fração proteica de lenta degradação da levedura, que impediu a sincronização energia/nitrogênio para maior degradação do resíduo. O pH do líquido ruminal decresceu linearmente nos animais mantidos com as dietas suplementadas com levedura. em todas as dietas, o pH e a concentração de N-NH3 foram adequados para o crescimento microbiano. As concentrações ruminais de acetato, propionato, butirato e ácidos graxos voláteis totais e a relação acetato:propionato não foram influenciadas pela suplementação com levedura. O resíduo do processamento do caroço de algodão é uma opção a ser utilizada no arraçoamento de bovinos.

Resistência do solo à penetração, cobertura vegetal e produtividade do milho em plantio direto escarificado

O objetivo deste trabalho foi avaliar a influência da operação da escarificação ao longo do tempo sobre a estrutura de um solo em plantio direto, assim como os seus efeitos sobre a produtividade do milho e a formação de cobertura vegetal. O trabalho foi conduzido em um NITOSSOLO VERMELHO no município de Botucatu, São Paulo, Brasil. O delineamento experimental foi o de blocos casualizados em esquema de parcelas subdivididas, sendo as parcelas o fator manejo do solo (em plantio direto e em escarificação) e as subparcelas o fator período de avaliação (quatro e 18 meses após a escarificação) com quatro repetições por tratamento. Os resultados indicaram que, após o período de quatro meses, a escarificação reduziu significativamente a resistência do solo à penetração, até a profundidade de atuação das hastes do escarificador (0,30 m), e, após o período de 18 meses, o efeito da escarificação sobre a resistência do solo à penetração ocorreu apenas na camada superficial do solo (0,05 e 0,10 m). em área cultivada em sistema plantio direto, o efeito do preparo do solo com escarificador sobre a resistência à penetração tende a desaparecer no período de 1,5 anos. A quantidade de matéria seca na superfície do solo, em plantio direto, foi 30% superior ao solo com antecedente de escarificação pelo período de quatro meses.

Reguladores de crescimento vegetal na concentração de macronutrientes em videira Itália

Em clima tropical semi-árido, o uso de reguladores vegetais em fruteiras permite o manejo do crescimento vegetativo, tão necessário ao escalonamento da produção e ao aumento da fertilidade das gemas. Estas substâncias influenciam vários fenômenos fisiológicos relacionados com a absorção mineral, como a condutância de membrana e utilização metabólica de íons. O objetivo deste trabalho foi avaliar o crescimento vegetativo, produção de matéria seca dos ramos, concentração e quantidade acumulada de N, P, K, Ca e Mg nos ramos e nos pecíolos e produção de panículas florais em resposta ao uso de reguladores vegetais, em plantas de videira da cultivar Itália. No experimento foram avaliados três ciclos vegetativos e cinco tratamentos (controle, chlormequat - 1500 mg L-1; daminozide - 3000 mg L-1; uniconazole - 30 mg L-1 e cloreto de mepiquat - 300 mg L-1), aplicados nas plantas em pulverizações aos 35 e 70 dias após a poda. Com o chlormequat e o uniconazole ocorreu efeito cumulativo nas plantas, quando aplicados em ciclos sucessivos da cultura, favorecendo o acúmulo de nutrientes e a diferenciação de gemas férteis em comparação com as plantas controle das videiras 'Itália'. Embora o daminozide tenha inibido significativamente o crescimento das plantas, não resultou em maior acúmulo de nutrientes e emissão de panículas florais nas plantas tratadas.

Aproveitamento de resíduo de caulim em cerâmica branca

The world market of Kaolin has been growing as new investments for better quality of materials have been applied. This market produces amounts of dross that are put in the environment in a wrong way, causing damages to it. Trying to reduce these damages, researches have been done in an attempt to use kaolin dross in ceramic. The disposal of kaolin dross in the environment by the industries of the states of Rio Grande do Norte and Paraiba have great impact in society. Usually this dross is disposed clandestinely in places like roads, river banks and lands of small cities. The present work shows the characteristics of the kaolin produced by the mining company in Junco do Seridó, Paraiba state, western Seridó, 300 km from Natal, in the border of both states. After that, researches were done to study its physical and the chemistry characteristics, trying to see if it can be used in white ceramic. The samples got were bolted in fabric of 325# . The technological characteristics tried to use it as a product in white ceramic. For that, it was made a haracterization of the subject matter through enlargement analyses, ATG and ATD, elaborating three formulations that were burned in four different temperatures, 1175, 1200, 1250 and 1300 degrees centigrade up to 30 minutes. After the burning, the subjects were submitted to water absorbing tests, linear retreating, apparent porosity, apparent specific mass, resistance to flexibility and MEV. For one of the mixtures it was obtained demanded properties for a semi porous material

Fibras de licuri: um reforço vegetal alternativo de compósitos poliméricos

This research is based, at first, on the seeking of alternatives naturals reinforced in place of polymeric composites, also named reinforced plastics. Therein, this work starts with a whole licuri fiber micro structural characterization, as alternative proposal to polymeric composites. Licuri fiber is abundant on the Bahia state flora, native from a palm tree called Syagrus Coronata (Martius) Beccari. After, it was done only licuri fiber laminar composite developing studies, in order to know its behavior when impregnated with thermofix resin. The composite was developed in laminar structure shape (plate with a single layer of reinforcement) and produced industrially. The layer of reinforcement is a fabric-fiber unidirectional of licuri up in a manual loom. Their structure was made of polyester resin ortofitálica (unsaturated) only reinforced with licuri fibers. Fiber characterization studies were based on physical chemistry properties and their constitution. It was made by tension, scanning electron microscopy (SEM), x-ray diffraction (RDX) and thermal analyses (TG and DTA) tests, besides fiber chemistry analyses. Relating their mechanical properties of strength and hardness testing, they were determined through unit axial tension test and flexion in three points. A study in order to know fiber/matrix interface effects, in the final composites results, was required. To better understand the mechanical behavior of the composite, macroscopic and microscopic optical analysis of the fracture was performed

Estudo do efeito da substituição de caulim por resíduo de caulim na fabricação de cerâmica de revestimento

Companies involved in kaolin mining and treatment represent an important area of industrial development in Brazil, significantly contribution to the worldwide production of such mineral. As a result, large volumes of kaolin residue are constantly generated and abandoned in the environment, negatively contributing to its preservation. In this scenario, the objective of the present study was to characterize the residue generated from kaolin mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Three compositions were prepared using kaolin residue contents of 10%, 20% and 30%. Samples were uniaxially pressed, fired at 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results showed that the residue basically consisted of kaolinite and successfully replaced raw kaolin in the preparation of ceramic title formulations without significantly affecting the properties of the fired material

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes

Estudo do potencial de utilização do resíduo da extração de esmeraldas na fabricação de cerâmica de revestimento

Companies involved in emerald mining and treatment represent an important area of industrial development in Brazil, with significative contribution to the worldwide production of such mineral. As a result, large volumes of emerald waste are constantly generated and abandoned in the environment, negatively contributing to its preservation. By the other side the interest of the use of mining waste as additive in ceramic products has been growing from researchers in recent years. The ceramic industry is constantly seeking to the marked amplification for the sector and perfecting the quality of the products and to increase the variety of applications. The technology of obtaining of ceramic tiles that uses mining residues assists market niches little explored. In this scenario, the objective of the present study was to characterize the residue generated from emerald mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Five compositions were prepared using emerald residue contents of 0%, 10%, 20%, 30% and 40%. Samples were uniaxially pressed, fired at 1000, 1100 and 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results shows that the emerald residue, basically consisted of 73% of (SiO2 + Al2O3) and 17,77% of (MgO + Na2O+ K2O) (that facilitates sintering), can be added to the ceramic tile materials with no detrimental effect on the properties of the sintered products

Estudo da introdução de resíduo de britagem de rocha calcária e cinza de biomassa de cana-de-açúcar em formulações de argamassas colantes

The adhesive mortars are a mixture of cement, sand, and additives to polymers that retain the mixing water and promotes adherence, being used in setting on various ceramic substrates. The sand used in the production of these mortars is from the riverbeds, and with the increasing restriction of these sands extraction by environmental agencies, and often having to be transported over long distances to the consumer center. This work aims to design and physical and mechanical characterization of ecological adhesive mortar with total replacement of natural sand by sand from the crushing of limestone, and the addition of mineral ash biomass of cane sugar in partial replacement cement used in the production of adhesive mortar , aiming compositions that meet the regulatory specifications for use adhesive mortar. Standardized tests to determine the tensile bond strength (NBR 14081-4), determination of open time (NBR 14081-3) and determination of slip (NBR 14081-5) were performed. Were also conducted trials squeeze flow in different formulation, the mortar with addition of 15 % gray biomass of cane sugar for cement mortars as well as the total replacement of natural sand by sand limestone crushing, got the best performance among the mortars studied, it was found that the addition of biomass to replace cement is perfectly feasible due to its pozzolanic activity, which contributed to this reduction in the cement matrix formation of adhesive mortar

Composito de poliuretano de mamona e residuo industrial para isolacao termica e absorcao sonora

This work proposes the development of an innovative material made from a vegetable polyurethane matrix and load of industrial waste, from retread tires, for thermal insulation and environmental comfort. Experimental procedures are presented, as well as the results of the thermal and acoustic performance of this composite material, made from an expansive foam derived from the castor seed oil and fiber of scrap tires. The residue was treated superficially with sodium hydroxide, to eliminate contaminants, and characterized macroscopically and microscopically. Samples were produced with addition of residues at levels of 5%, 10%, 15% and 20% by weight, for determination of thermal properties: conductivity, heat capacity and thermal diffusivity, sound absortion index and density. The results were compared to commercially available thermal insulation and sound absorbing products. According to the analysis of results, it was concluded that the developed composite presents characteristics that qualify it as a thermal insulation with superior performance, compared to commercial available insulation, and sound absorption capacity greater than the castor oil polyurethane s, without addition of the residue

Obtenção e caracterização de extrato microencapsulado de resíduo agroindustrial de acerola

Acerola (Malpighia emarginata D.C.) is a red fruit widely cultivated in Brazil, especially in the Northeastern region. Its increasing demand is attributed to its high ascorbic acid contents. Besides ascorbic acid, widely known by its health-benefit effects, acerola is rich in anthocyanins, which contribute for the antioxidant power of the fruit. Acerola processing produces a bright-red pomace, usually discarded. The further processing of this pomace, in order to explore its antioxidant compounds, could enhance acerola market value and rentability of its processing. Both ascorbic acid and anthocyanins are highly susceptible to degradation, that can be delayed by microencapsulation, which consists on packing particles (core) in an edible matrix (wall material). This work has been made with the purpose of producing a microencapsulated acerola pomace extract, which could be used by the food industry as a functional ingredient with antioxidant and coloring properties. Antioxidant compounds were recovered by pressing the pomace diluted in a solvent (a citric acid aqueous solution), by using a central composite design, with two variables: citric acid concentration in the solvent (0-2%), and solvent: pomace mass ratio (2:1-6:1). The acerola pomace extract was then microencapsulated by spray drying. A central composite design was adopted, with three variables: inlet temperature of the spray dryer (170o-200oC), wall material: acerola solids mass ratio (2:1-5:1), and degree of maltodextrin replacement by cashew tree gum as wall material (0-100%). The cashew tree gum was used because of its similarity to arabic gum, which is regarded as the wall material by excellence. The following conditions were considered as optimal for extraction of anthocyanins and ascorbic acid: solvent/pomace ratio, 5:1, and no citric acid in the solvent. 82.47% of the anthocyanins were recovered, as well as 83.22% of the ascorbic acid. Anthocyanin and ascorbic acid retentions were favored by lower inlet temperatures, higher wall material: acerola solids mass ratio and higher maltodextrin replacement by cashew tree gum, which was presented as a promising wall material. The more adequate microencapsulation conditions, based not only on retention of antioxidant compounds but also on physical properties of the final powder, were the following: inlet temperature, 185oC; wall material: acerola solids mass ratio, 5:1, and minimum degree of maltodextrin replacement by cashew tree gum, 50%

Remoção de óleo da água de produção por flotação em coluna utilizando tensoativos de origem vegetal

In the petroleum industry, water is always present in the reservoir formation together with petroleum and natural gas and this fact provokes the production of water with petroleum, resulting in a great environmental impact. Several methods can be applied for treatment of oily waters, such as: gravitational vases, granulated media filtration systems, flotation process, centrifugation process and the use of hydrocyclones, which can also be used in a combined way. However, the flotation process has showed a great efficiency as compared with other methods, because these methods do not remove great part of the emulsified oil. In this work was investigated the use of surfactants derived from vegetable oils, OSS and OGS, as collectors, using the flotation process in a glass column with a porous plate filter in its base for the input of the gaseous steam. For this purpose, oil/water emulsions were prepared using mechanical stirring, with concentrations around 300 ppm. The air flow rate was set at 700 cm3/min and the porous plate filter used for the generation of the air bubbles has pore size varying from 16 to 40 Pm. The column operated at constant volume (1500mL). A new methodology has been developed to collect the samples, where, instead of collecting the water phase, it was collected the oil phase removed by the process in the top of the flotation column. It has been observed that it is necessary to find an optimum surfactant concentration to achieve enhanced removal efficiency. Being for OSS 1.275 mmol/L and for OGS 0.840 mmol/L, with removal efficiencies of 93% and 99%, respectively, using synthetic solutions. For the produced water, the removal in these concentrations was 75% for OSS and 65% for OGS. It is possible to remove oil from water in a flotation process using surfactants of high HLB, fact that is against the own definition of HLB (Hydrophile-Lipophile Balance). The interfacial tension is an important factor in the oil removal process using a flotation process, because it has direct interference in the coalescence of the oil drops. The spreading of the oil of the air bubble should be considered in the process, and for the optimum surfactant concentrations it reached a maximum value. The removal kinetics for the flotation process using surfactants in the optimum concentration has been adjusted according to a first order model, for synthetic water as for the produced water.

Estudo da incorporação de resíduo industrial polimérico ao CAP

This work presents the incorporation of an industrial polymeric waste into a petroleum asphalt cement with penetration grade 50-60 (CAP 50-60). The main goal of this research is the development of a polymer-modified asphalt, with improvements in its physical properties, in order to obtain a more resistant material to the traffic loads. Furthermore, the use of this polymeric waste will result in economic and environmental benefits. The CAP 50-60 used in this research was kindly supplied by LUBNOR Lubrificantes e Derivados de Petróleo do Nordeste (produced in Fazenda Belém Aracati - Ceará) and the industrial polymeric waste was provided by a button manufacturer industry, located in Rio Grande do Norte state. This polymeric waste represents an environmental problem due to its difficulty in recycling and disposal, being necessary the payment by the industry to a landfill. The difficulty in its reuse is for being this material a termofixed polymer, as a result, the button chips resulting from the molding process cannot be employed for the same purpose. The first step in this research was the characterization of the polymeric waste, using Differential Scanning Calorimetry (DSC) Infrared spectroscopy (IR spectroscopy), and Thermogravimetric analysis (TGA). Based on the results, the material was classified as unsaturated polyester. After, laboratory experiments were accomplished seeking to incorporate the polymeric waste into the asphalt binder according to a 23 experimental factorial design, using as main factors: the polymer content (2%, 7% and 14%), the temperature of the mixture (140 and 180 oC) and the reaction time (20 and 60 minutes). The characterization of the polymer-modified asphalt was accomplished by traditional tests, such as: penetration, ring and ball softening point, viscosity, ductility and flash point temperature. The obtained results demonstrated that the addition of the polymeric waste into the asphalt binder modified some of its physical properties. However, this addition can be considered as a feasible alternative for the use of the polymeric waste, which is a serious environmental and technological problem.