Design of compression reinforcement in reinforced concrete membrane

This paper presents a method to design membrane elements of concrete with orthogonal mesh of reinforcement which are subject to compressive stress. Design methods, in general, define how to quantify the reinforcement necessary to support the tension stress and verify if the compression in concrete is within the strength limit. In case the compression in membrane is excessive, it is possible to use reinforcements subject to compression. However, there is not much information in the literature about how to design reinforcement for these cases. For that, this paper presents a procedure which uses the model based on Baumann's [1] criteria. The strength limits used herein are those recommended by CEB [3], however, a model is proposed in which this limit varies according to the tensile strain which occur perpendicular to compression. This resistance model is based on concepts proposed by Vecchio e Collins [2].

Development of musculoskeletal models for the design and the pre-clinical validation of hip resurfacing prosthesis

Background. The surgical treatment of dysfunctional hips is a severe condition for the patient and a costly therapy for the public health. Hip resurfacing techniques seem to hold the promise of various advantages over traditional THR, with particular attention to young and active patients. Although the lesson provided in the past by many branches of engineering is that success in designing competitive products can be achieved only by predicting the possible scenario of failure, to date the understanding of the implant quality is poorly pre-clinically addressed. Thus revision is the only delayed and reliable end point for assessment. The aim of the present work was to model the musculoskeletal system so as to develop a protocol for predicting failure of hip resurfacing prosthesis. Methods. Preliminary studies validated the technique for the generation of subject specific finite element (FE) models of long bones from Computed Thomography data. The proposed protocol consisted in the numerical analysis of the prosthesis biomechanics by deterministic and statistic studies so as to assess the risk of biomechanical failure on the different operative conditions the implant might face in a population of interest during various activities of daily living. Physiological conditions were defined including the variability of the anatomy, bone densitometry, surgery uncertainties and published boundary conditions at the hip. The protocol was tested by analysing a successful design on the market and a new prototype of a resurfacing prosthesis. Results. The intrinsic accuracy of models on bone stress predictions (RMSE < 10%) was aligned to the current state of the art in this field. The accuracy of prediction on the bone-prosthesis contact mechanics was also excellent (< 0.001 mm). The sensitivity of models prediction to uncertainties on modelling parameter was found below 8.4%. The analysis of the successful design resulted in a very good agreement with published retrospective studies. The geometry optimisation of the new prototype lead to a final design with a low risk of failure. The statistical analysis confirmed the minimal risk of the optimised design over the entire population of interest. The performances of the optimised design showed a significant improvement with respect to the first prototype (+35%). Limitations. On the authors opinion the major limitation of this study is on boundary conditions. The muscular forces and the hip joint reaction were derived from the few data available in the literature, which can be considered significant but hardly representative of the entire variability of boundary conditions the implant might face over the patients population. This moved the focus of the research on modelling the musculoskeletal system; the ongoing activity is to develop subject-specific musculoskeletal models of the lower limb from medical images. Conclusions. The developed protocol was able to accurately predict known clinical outcomes when applied to a well-established device and, to support the design optimisation phase providing important information on critical characteristics of the patients when applied to a new prosthesis. The presented approach does have a relevant generality that would allow the extension of the protocol to a large set of orthopaedic scenarios with minor changes. Hence, a failure mode analysis criterion can be considered a suitable tool in developing new orthopaedic devices.

High resolution study of local stress inside alumina - micro mechanical analysis using laser scanning confocal microscope

The aim of this work is to measure the stress inside a hard micro object under extreme compression. To measure the internal stress, we compressed ruby spheres (a-Al2O3: Cr3+, 150 µm diameter) between two sapphire plates. Ruby fluorescence spectrum shifts to longer wavelengths under compression and can be related to the internal stress by a conversion coefficient. A confocal laser scanning microscope was used to excite and collect fluorescence at desired local spots inside the ruby sphere with spatial resolution of about 1 µm3. Under static external loads, the stress distribution within the center plane of the ruby sphere was measured directly for the first time. The result agreed to Hertz’s law. The stress across the contact area showed a hemispherical profile. The measured contact radius was in accord with the calculation by Hertz’s equation. Stress-load curves showed spike-like decrease after entering non-elastic phase, indicating the formation and coalescence of microcracks, which led to relaxing of stress. In the vicinity of the contact area luminescence spectra with multiple peaks were observed. This indicated the presence of domains of different stress, which were mechanically decoupled. Repeated loading cycles were applied to study the fatigue of ruby at the contact region. Progressive fatigue was observed when the load exceeded 1 N. As long as the load did not exceed 2 N stress-load curves were still continuous and could be described by Hertz’s law with a reduced Young’s modulus. Once the load exceeded 2 N, periodical spike-like decreases of the stress could be observed, implying a “memory effect” under repeated loading cycles. Vibration loading with higher frequencies was applied by a piezo. Redistributions of intensity on the fluorescence spectra were observed and it was attributed to the repopulation of the micro domains of different elasticity. Two stages of under vibration loading were suggested. In the first stage continuous damage carried on until certain limit, by which the second stage, e.g. breakage, followed in a discontinuous manner.

Oxidativer Stress als Modulator der NMDA-Rezeptorexpression auf zerebrovaskulären Endothelzellen

Oxidativer Stress in Form reaktiver Sauerstoffspezies (ROS) und Exzitotoxizität durch supraphysiologische Konzentrationen des Neurotransmitters Glutamat sind nicht nur beteiligt an der Pathogenese vielzähliger neurodegenerativer Erkrankungen wie Schlaganfall, Hirntrauma, Alzheimer Demenz oder Multipler Sklerose, sondern spielen zudem eine Schlüsselrolle im dort beobachteten Zusammenbruch der Blut-Hirn-Schranke. Glutamat führt durch Stimulation neuronaler und endothelialer NMDA-Rezeptoren zu einer Generierung von ROS. Nicht verfolgt worden war bisher, welche Auswirkungen ROS umgekehrt auch auf den NMDA-Rezeptor haben könnten. Im Rahmen der vorliegenden Arbeit wurde daher untersucht, ob und in welcher Weise die Exposition gegenüber reaktiven Sauerstoffspezies einen Einfluss auf die Expression und Aktivierbarkeit von NMDA-Rezeptoren auf zerebrovaskulären Endothelzellen ausübt.rnEs konnte zunächst die Expression der funktionell obligaten NR-1 Untereinheit des NMDA-Rezeptors auf der verwendeten Zelllinie b.End3 mittels Immunfluoreszenz-Mikroskopie gesichert werden. Ein Nachweis von mRNA für die Untereinheiten NR1 und NR2B, C und D erfolgte mittels RT-PCR. In der Analyse der replizierten RNA zeigten sich Hinweise für eine heterogene Komposition der exprimierten endothelialen NMDA-Rezeptoren.rnEs konnte weiter mit Hilfe der In-Cell-Western-Technik gezeigt werden, dass die Expression des NMDA-Rezeptors durch transiente Stimulation mit reaktiven Sauerstoffspezies im Sinne einer Heraufregulation moduliert werden kann. Die Stimulation der Zellen mit den reaktiven Sauerstoffspezies O2-, ONOO- und H2O2 führte dabei im Experiment zu einer deutlichen Zunahme der NR1-Expression, die spätestens nach 72 Stunden höchst signifikant war.rnUm zu überprüfen, welche Bedeutung diese Überexpression für die Integrität der Blut-Hirn-Schranke unter den exzitotoxischen Bedingungen hoher Glutamatkonzentrationen haben könnte, wurde mit Hilfe des ECIS-Systems („Electrical Cell-Substrate Impedance Sensing“) die Impedanz ROS-präexponierter Endothelmonolayer gemessen. Auf Rezeptorstimulation mit dem spezifischen Agonisten NMDA reagierten die vorbehandelten Gruppen mit einem Abfall der Impedanz gegenüber der nicht vorbehandelten Kontrolle.rnrnDie vorliegenden Ergebnisse zeigen, dass ROS in der Lage sind, funktionelle endotheliale NMDA-Rezeptoren zu induzieren und auf diesem Weg zu einem verstärkten Abfall der BHS-Integrität unter den Bedingungen exzitotoxischen und oxidativen Stresses führen. Dies stellt einen neuen Mechanismus zur Erklärung der Pathogenese des Blut-Hirn-Schrankenversagens dar.

Finite element modeling of the cement-bone interface beneath the tibial tray of a total knee arthroplasty: Study of the stress shielding effect (modellazione agli elementi finiti dell'interfaccia cemento-osso sotto il piatto tibiale di protesi totale di ginocchio: Analisi dello stress shielding)

The goal of this thesis was the study of the cement-bone interface in the tibial component of a cemented total knee prosthesis. One of the things you can see in specimens after in vivo service is that resorption of bone occurs in the interdigitated region between bone and cement. A stress shielding effect was investigated as a cause to explain bone resorption. Stress shielding occurs when bone is loaded less than physiological and therefore it starts remodeling according to the new loading conditions. µCT images were used to obtain 3D models of the bone and cement structure and a Finite Element Analysis was used to simulate different kind of loads. Resorption was also simulated by performing erosion operations in the interdigitated bone region. Finally, 4 models were simulated: bone (trabecular), bone with cement, and two models of bone with cement after progressive erosions of the bone. Compression, tension and shear test were simulated for each model in displacement-control until 2% of strain. The results show how the principal strain and Von Mises stress decrease after adding the cement on the structure and after the erosion operations. These results show that a stress shielding effect does occur and rises after resorption starts.

Implications of regional fault distribution and kinematics for the uplift of rift flanks around the Rwenzori Mountains, Southwestern Uganda

Das Ziel dieser Arbeit bestand in der Untersuchung der Störungsverteilung und der Störungskinematik im Zusammenhang mit der Hebung der Riftschultern des Rwenzori Gebirges.rnDas Rwenzori Gebirge befindet sich im NNE-SSWbis N-S verlaufenden Albertine Rift, des nördlichsten Segments des westlichen Armes des Ostafrikanischen Grabensystems. Das Albertine Rift besteht aus Becken unterschiedlicher Höhe, die den Lake Albert, Lake Edward, Lake George und Lake Kivu enthalten. Der Rwenzori horst trennt die Becken des Lake Albert und des Lake Edward. Es erstreckt sich 120km in N-S Richtung, sowie 40-50km in E-W Richtung, der h¨ochste Punkt befindet sich 5111 ü. NN. Diese Studie untersucht einen Abschnitt des Rifts zwischen etwa 1°N und 0°30'S Breite sowie 29°30' und 30°30' östlicher Länge ersteckt. Auch die Feldarbeit konzentrierte sich auf dieses Gebiet.rnrnHauptzweck dieser Studie bestand darin, die folgende These auf ihre Richtigkeit zu überprüfen: ’Wenn es im Verlauf der Zeit tatsächlich zu wesentlichen Änderungen in der Störungskinematik kam, dann ist die starke Hebung der Riftflanken im Bereich der Rwenzoris nicht einfach durch Bewegung entlang der Graben-Hauptst¨orungen zu erklären. Vielmehr ist sie ein Resultat des Zusammenspiels mehrerer tektonische Prozesse, die das Spannungsfeld beeinflussen und dadurch Änderungen in der Kinematik hervorrufen.’ Dadurch konzentrierte sich die Studie in erster Linie auf die Störungsanalyse.rnrnDie Kenntnis regionaler Änderungen der Extensionsrichtung ist entscheidend für das Verständnis komplexer Riftsysteme wie dem Ostafrikanischen Graben. Daher bestand der Kern der Untersuchung in der Kartierung von Störungen und der Untersuchung der Störungskinematik. Die Aufnahme strukturgeologischer Daten konzentrierte sich auf die Ugandische Seite des Rifts, und Pal¨aospannungen wurden mit Hilfe von St¨orungsdaten durch Spannungsinversion rekonstruiert.rnDie unterschiedliche Orientierung spr¨oder Strukturen im Gelände, die geometrische Analyse der geologischen Strukturen sowie die Ergebnisse von Mikrostrukturen im Dünnschliff (Kapitel 4) weisen auf verschiedene Spannungsfelder hin, die auf mögliche Änderungen der Extensionsrichtung hinweisen. Die Resultate der Spannungsinversion sprechen für Ab-, Über- und Blattverschiebungen sowie für Schrägüberschiebungen (Kapitel 5). Aus der Orientierung der Abschiebungen gehen zwei verschiedene Extensionsrichtungen hervor: im Wesentlichen NW-SE Extension in fast allen Gebieten, sowie NNE-SSW Extension im östlichen Zentralbereich.rnAus der Analyse von Blattverschiebungen ergaben sich drei unterschiedliche Spannungszustände. Zum Einen NNW-SSE bis N-S Kompression in Verbindung mit ENE-WSW bzw E-W Extension wurde für die nördlichen und die zentralen Ruwenzoris ausgemacht. Ein zweiter Spannungszustand mit WNW-ESE Kompression/NNE-SSW Extension betraf die Zentralen Rwenzoris. Ein dritter Spannungszustand mit NNW-SSE Extension betraf den östlichen Zentralteil der Rwenzoris. Schrägüberschiebungen sind durch dazu schräge Achsen charakterisiert, die für N-S bis NNW-SSE Kompression sprechen und ausschließlich im östlichen Zentralabschnitt auftreten. Überschiebungen, die hauptsächlich in den zentralen und den östlichen Rwenzoris auftreten, sprechen für NE-SW orientierten σ2-Achsen und NW-SE Extension.rnrnEs konnten drei unterschiedliche Spannungseinflüsse identifiziert werden: auf die kollisionsbedingte Bildung eines Überschiebungssystem folgte intra-kratonische Kompression und schließlich extensionskontrollierte Riftbildung. Der Übergang zwischen den beiden letztgenannten Spannungszuständen erfolgte Schrittweise und erzeugte vermutlich lokal begrenzte Transpression und Transtension. Gegenw¨artig wird die Störungskinematik der Region durch ein tensiles Spannungsregime in NW-SE bis N-S Richtung bestimmt.rnrnLokale Spannungsvariationen werden dabei hauptsächlich durch die Interferenzrndes regionalen Spannungsfeldes mit lokalen Hauptst¨orungen verursacht. Weitere Faktoren die zu lokalen Veränderungen des Spannungsfeldes führen können sind unterschiedliche Hebungsgeschwindigkeiten, Blockrotation oder die Interaktion von Riftsegmenten. Um den Einfluß präexistenter Strukturen und anderer Bedingungen auf die Hebung der Rwenzoris zu ermitteln, wurde der Riftprozeß mit Hilfe eines analogen ’Sandbox’-Modells rekonstruiert (Kapitel 6). Da sich die Moho-Diskontinuität im Bereich des Arbeitsgebietes in einer Tiefe von 25 km befindet, aktive Störungen aber nur bis zu einer Tiefe von etwa 20 km beobachtet werden können (Koehn et al. 2008), wurden nur die oberen 25 km im Modell nachbebildet. Untersucht und mit Geländebeobachtungen verglichen wurden sowohl die Reihenfolge, in der Riftsegmente entstehen, als auch die Muster, die sich im Verlauf der Nukleierung und des Wachstums dieser Riftsegmente ausbilden. Das Hauptaugenmerk wurde auf die Entwicklung der beiden Subsegmente gelegt auf denen sich der Lake Albert bzw. der Lake Edward und der Lake George befinden, sowie auf das dazwischenliegende Rwenzori Gebirge. Das Ziel der Untersuchung bestand darin herauszufinden, in welcher Weise das südwärts propagierende Lake Albert-Subsegment mit dem sinistral versetzten nordwärts propagierenden Lake Edward/Lake George-Subsegment interagiert.rnrnVon besonderem Interesse war es, in welcherWeise die Strukturen innerhalb und außerhalb der Rwenzoris durch die Interaktion dieser Riftsegmente beeinflußt wurden. rnrnDrei verschiedene Versuchsreihen mit unterschiedlichen Randbedingungen wurden miteinander verglichen. Abhängig vom vorherrschenden Deformationstyp der Transferzone wurden die Reihen als ’Scherungs-dominiert’, ’Extensions-dominiert’ und als ’Rotations-dominiert’ charakterisiert. Die Beobachtung der 3-dimensionalen strukturellen Entwicklung der Riftsegmente wurde durch die Kombination von Modell-Aufsichten mit Profilschnitten ermöglicht. Von den drei genannten Versuchsreihen entwickelte die ’Rotationsdominierten’ Reihe einen rautenförmiger Block im Tranferbereich der beiden Riftsegmente, der sich um 5−20° im Uhrzeigersinn drehte. DieserWinkel liegt im Bereich des vermuteten Rotationswinkel des Rwenzori-Blocks (5°). Zusammengefasst untersuchen die Sandbox-Versuche den Einfluss präexistenter Strukturen und der Überlappung bzw. Überschneidung zweier interagierender Riftsegmente auf die Entwicklung des Riftsystems. Sie befassen sich darüber hinaus mit der Frage, welchen Einfluss Blockbildung und -rotation auf das lokale Stressfeld haben.

Wet and dry model granulates under mechanical load : a confocal microscopy study

Granular matter, also known as bulk solids, consists of discrete particles with sizes between micrometers and meters. They are present in many industrial applications as well as daily life, like in food processing, pharmaceutics or in the oil and mining industry. When handling granular matter the bulk solids are stored, mixed, conveyed or filtered. These techniques are based on observations in macroscopic experiments, i.e. rheological examinations of the bulk properties. Despite the amply investigations of bulk mechanics, the relation between single particle motion and macroscopic behavior is still not well understood. For exploring the microscopic properties on a single particle level, 3D imaging techniques are required.rnThe objective of this work was the investigation of single particle motions in a bulk system in 3D under an external mechanical load, i.e. compression and shear. During the mechanical load the structural and dynamical properties of these systems were examined with confocal microscopy. Therefor new granular model systems in the wet and dry state were designed and prepared. As the particles are solid bodies, their motion is described by six degrees of freedom. To explore their entire motion with all degrees of freedom, a technique to visualize the rotation of spherical micrometer sized particles in 3D was developed. rnOne of the foci during this dissertation was a model system for dry cohesive granular matter. In such systems the particle motion during a compression of the granular matter was investigated. In general the rotation of single particles was the more sensitive parameter compared to the translation. In regions with large structural changes the rotation had an earlier onset than the translation. In granular systems under shear, shear dilatation and shear zone formation were observed. Globally the granular sediments showed a shear behavior, which was known already from classical shear experiments, for example with Jenike cells. Locally the shear zone formation was enhanced, when near the applied load a pre-diluted region existed. In regions with constant volume fraction a mixing between the different particle layers occurred. In particular an exchange of particles between the current flowing region and the non-flowing region was observed. rnThe second focus was on model systems for wet granular matter, where an additional binding liquid is added to the particle suspension. To examine the 3D structure of the binding liquid on the micrometer scale independently from the particles, a second illumination and detection beam path was implemented. In shear and compression experiments of wet clusters and bulk systems completely different dynamics compared to dry cohesive models systems occured. In a Pickering emulsion-like system large structural changes predominantly occurred in the local environment of binding liquid droplets. These large local structural changes were due to an energy interplay between the energy stored in the binding droplet during its deformation and the binding energy of particles at the droplet interface. rnConfocal microscopy in combination with nanoindentation gave new insights into the single particle motions and dynamics of granular systems under a mechanical load. These novel experimental results can help to improve the understanding of the relationship between bulk properties of granular matter, such as volume fraction or yield stress and the dynamics on a single particle level.rnrn

Unique paleopathology in a pre-Columbian mummy remnant from Southern Peru--severe cervical rotation trauma with subluxation of the axis as cause of death

We describe the multidisciplinary findings in a pre-Columbian mummy head from Southern Peru (Cahuachi, Nazca civilisation, radiocarbon dating between 120 and 750 AD) of a mature male individual (40-60 years) with the first two vertebrae attached in pathological position. Accordingly, the atlanto-axial transition (C1/C2) was significantly rotated and dislocated at 38° angle associated with a bulging brownish mass that considerably reduced the spinal canal by circa 60%. Using surface microscopy, endoscopy, high-resolution multi-slice computer tomography, paleohistology and immunohistochemistry, we identified an extensive epidural hematoma of the upper cervical spinal canal-extending into the skull cavity-obviously due to a rupture of the left vertebral artery at its transition between atlas and skull base. There were no signs of fractures of the skull or vertebrae. Histological and immunohistochemical examinations clearly identified dura, brain residues and densely packed corpuscular elements that proved to represent fresh epidural hematoma. Subsequent biochemical analysis provided no evidence for pre-mortal cocaine consumption. Stable isotope analysis, however, revealed significant and repeated changes in the nutrition during his last 9 months, suggesting high mobility. Finally, the significant narrowing of the rotational atlanto-axial dislocation and the epidural hematoma probably caused compression of the spinal cord and the medulla oblongata with subsequent respiratory arrest. In conclusion, we suggest that the man died within a short period of time (probably few minutes) in an upright position with the head rotated rapidly to the right side. In paleopathologic literature, trauma to the upper cervical spine has as yet only very rarely been described, and dislocation of the vertebral bodies has not been presented.

Stress free configuration of the human eye

Numerical simulations of eye globes often rely on topographies that have been measured in vivo using devices such as the Pentacam or OCT. The topographies, which represent the form of the already stressed eye under the existing intraocular pressure, introduce approximations in the analysis. The accuracy of the simulations could be improved if either the stress state of the eye under the effect of intraocular pressure is determined, or the stress-free form of the eye estimated prior to conducting the analysis. This study reviews earlier attempts to address this problem and assesses the performance of an iterative technique proposed by Pandolfi and Holzapfel [1], which is both simple to implement and promises high accuracy in estimating the eye's stress-free form. A parametric study has been conducted and demonstrated reliance of the error level on the level of flexibility of the eye model, especially in the cornea region. However, in all cases considered 3-4 analysis iterations were sufficient to produce a stress-free form with average errors in node location <10(-6)mm and a maximal error <10(-4)mm. This error level, which is similar to what has been achieved with other methods and orders of magnitude lower than the accuracy of current clinical topography systems, justifies the use of the technique as a pre-processing step in ocular numerical simulations.

[Pre-eclampsia and its psychosocial sequelae]

In the present work some psychosomatic conditions in the setting of preeclampsia are described. The important psychosocial consequences for women suffering from this disease and the drawback for their partners will be elucidated. Preeclampsia as a disease including hypertension, proteinuria and generalized edema is often associted with generalized seizures occuring most commonly at the end of the second trimenon of pregnancy. The disease bears a heavy risk for the mothers as well as for her unborn child. Until now the exact pathophysiological basis of the disease has not been entirely elucidated. For the pregnant woman and her psychosocial surrounding the outbreak of the disease is in most cases unexpected. During development of the disease she has to face a role change from a so far normal pregnancy to a high-risk situation. This may change also the attitude to the unborn child by herself and her partner. The preterm delivery induced therapeutically, together with the succeeding problems for the newborn complete the high psychosocial stress related to the entire situation. Therefore it is useful and important to offer psychosocial support to the mother as well as to her parter during the illness and the time after delivery.

Automation of shear-wave splitting parameter determination of local earthquakes at Yellowstone : application as indicator of crustal stress and temporal variation

Shear-wave splitting can be a useful technique for determining crustal stress fields in volcanic settings and temporal variations associated with activity. Splitting parameters were determined for a subset of local earthquakes recorded from 2000-2010 at Yellowstone. Analysis was automated using an unsupervised cluster analysis technique to determine optimum splitting parameters from 270 analysis windows for each event. Six stations clearly exhibit preferential fast polarization values sub-orthogonal to the direction of minimum horizontal compression. Yellowstone deformation results in a local crustal stress field differing from the regional field dominated by NE-SW extension, and fast directions reflect this difference rotating around the caldera maintaining perpendicularity to the rim. One station exhibits temporal variations concordant with identified periods of caldera subsidence and uplift. From splitting measurements, we calculated a crustal anisotropy of ~17-23% and crack density ~0.12-0.17 possibly resulting from stress-aligned fluid filled microcracks in the upper crust and an active hydrothermal system.

Omega-3 fatty acids and the neurovascular responses to mental stress in humans

Hypertension is the most prevalent form of cardiovascular disease (CVD) in the world, and is known to increase the risk for developing other diseases. Recently, the American Heart Association introduced a new classification of blood pressure, prehypertension (PHT). The criteria for PHT include a systolic of 120-139 mmHg and/or a diastolic blood pressure of 80-89 mmHg. It has been observed that individuals with PHT have a higher risk of developing hypertension later in life. Therefore, it is important to understand the mechanisms contributing to PHT in order to possibly prevent hypertension. Omega-3 fatty acids found in fish oils have been suggested as a means of lowering blood pressure. However, little is known on the effects of fish oil in PHT humans. Therefore we conducted two studies. In Study 1 we investigated PHT and normotensive (NT) individuals during a mental stress task. Mental stress is known to contribute to the development of hypertension. In Study 2 PHT and NT subjects were placed in an eight week double-blind placebo controlled study in which subjects consumed 9g/day of either fish oil or placebo (olive oil) in addition to their regular diets. Subjects were tested during a resting baseline (seated and supine), 5 minutes of a mental stress task, and 5 minutes of recovery both pre and post supplementation. We measured arterial pressure (AP), heart rate (HR), muscle sympathetic nerve activity (MSNA), and forearm and calf vascular responses. In Study 1 PHT demonstrated augmented AP and blunted vasodilation during mental stress, but MSNA did not change. In Study 2, fish oil did not directly influence blood pressure, MSNA or vascular responses to mental stress. However, it became clear that fish oil had an effect on some but not all subjects (both PHT and NT). Specifically, subjects who experienced a reduced blood pressure response to fish oil also demonstrated a decrease in MSNA and HR during mental stress. Collectively, the investigations in this dissertation had several novel findings. First, PHT individuals demonstrate an augmented pressor and blunted vascular response to mental stress, a response that may be contributing to the development of hypertension. Second, fish oil does not consistently lower resting blood pressure, but the interindividual responses may be related to MSNA. Third, fish oil attenuated the heart rate and MSNA responses and to mental stress in both PHT and NT. In conclusion, we found that there are both similarities and differences in the way PHT and NT individuals respond to mental stress and fish oil.

Acute alcohol ingestion and sympathetic neural responses during orthostatic stress in humans

Acute alcohol consumption has been reported to decrease mean arterial pressure (MAP) during orthostatic challenge, a response that may contribute to alcohol-mediated hypotension and eventually syncope. Muscle sympathetic nerve activity (MSNA) increases during orthostatic stress to help maintain MAP, yet the influence of alcohol on MSNA during orthostatic stress has not been determined. We hypothesized that alcohol ingestion would blunt arterial blood pressure and MSNA responses to progressive lower body negative pressure (LBNP). MAP, MSNA, and heart rate (HR) were recorded during progressive LBNP (-5, -10, -15, -20, -30, and -40 mmHg; 3 min/stage) in 30 subjects(age 24 ± 1 yrs). After an initial progressive LBNP protocol (pre-treatment), subjects were randomly assigned to consume alcohol (0.8g ethanol/kg body mass; n=15) or placebo (n=15) and then repeated the progressive LBNP protocol (post-treatment). Alcohol increased (drug × treatment, P ≤ 0.05) resting HR (59 ± 2 to 65 ± 2 beats/min) and MSNA (13 ± 3 to 19 ± 4 bursts/min) when compared to placebo. While alcohol increased MAP (83 ± 2 to 87 ± 2 mmHg), these increases were also observed with placebo (82 ± 2 to 88 ± 1 mmHg; treatment, P < 0.05; drug × treatment, P > 0.05). During progressive LBNP, a prominent decrease in MAP was observed after alcohol (drug × time × treatment, P < 0.05), but not placebo. There was also a significant attenuated response in forearm vascular resistance (FVR) during progressive LBNP (drug × time × treatment, P < 0.05). MSNA and HR increased during all LBNP protocols, but there were no differences between treatments or groups (drugs). In summary, acute alcohol ingestion induces an attenuation in blood pressure response during an orthostatic challenge, possibly due to the effect that alcohol has on impairing peripheral blood vessel constriction.

COMPRESSION BEHAVIOR AT HIGH STRAIN RATE FOR AN ULTRA HIGH PERFORMANCE CONCRETE

The need for a stronger and more durable building material is becoming more important as the structural engineering field expands and challenges the behavioral limits of current materials. One of the demands for stronger material is rooted in the effects that dynamic loading has on a structure. High strain rates on the order of 101 s-1 to 103 s-1, though a small part of the overall types of loading that occur anywhere between 10-8 s-1 to 104 s-1 and at any point in a structures life, have very important effects when considering dynamic loading on a structure. High strain rates such as these can cause the material and structure to behave differently than at slower strain rates, which necessitates the need for the testing of materials under such loading to understand its behavior. Ultra high performance concrete (UHPC), a relatively new material in the U.S. construction industry, exhibits many enhanced strength and durability properties compared to the standard normal strength concrete. However, the use of this material for high strain rate applications requires an understanding of UHPC’s dynamic properties under corresponding loads. One such dynamic property is the increase in compressive strength under high strain rate load conditions, quantified as the dynamic increase factor (DIF). This factor allows a designer to relate the dynamic compressive strength back to the static compressive strength, which generally is a well-established property. Previous research establishes the relationships for the concept of DIF in design. The generally accepted methodology for obtaining high strain rates to study the enhanced behavior of compressive material strength is the split Hopkinson pressure bar (SHPB). In this research, 83 Cor-Tuf UHPC specimens were tested in dynamic compression using a SHPB at Michigan Technological University. The specimens were separated into two categories: ambient cured and thermally treated, with aspect ratios of 0.5:1, 1:1, and 2:1 within each category. There was statistically no significant difference in mean DIF for the aspect ratios and cure regimes that were considered in this study. DIF’s ranged from 1.85 to 2.09. Failure modes were observed to be mostly Type 2, Type 4, or combinations thereof for all specimen aspect ratios when classified according to ASTM C39 fracture pattern guidelines. The Comite Euro-International du Beton (CEB) model for DIF versus strain rate does not accurately predict the DIF for UHPC data gathered in this study. Additionally, a measurement system analysis was conducted to observe variance within the measurement system and a general linear model analysis was performed to examine the interaction and main effects that aspect ratio, cannon pressure, and cure method have on the maximum dynamic stress.

The effects of aspirin and nonselective beta blockade on the acute prothrombotic response to psychosocial stress in apparently healthy subjects

We hypothesized that the 2 cardiovascular drugs aspirin and propranolol attenuate the prothrombotic response to acute psychosocial stress relative to placebo medication. We randomized 56 healthy subjects, double-blind, to 5-day treatment with an oral dose of either 100 mg of aspirin plus 80 mg of propranolol combined, single aspirin, single propranolol, or placebo medication. Thereafter, subjects underwent a 13-minute psychosocial stressor. Plasma levels of von Willebrand factor antigen (VWF:Ag), fibrinogen, coagulation factor VII (FVII:C) and XII (FXII:C) activity, and D-dimer were determined in blood samples collected immediately pre- and post-stress and 45 minutes post-stress. The stress-induced changes in prothrombotic measures were adjusted for gender, age, body mass index, mean arterial blood pressure, smoking status, and sleep quality. There was an increase in VWF:Ag levels from immediately pre-stress to 45 minutes post-stress in the placebo group relative to the 3 subject groups with verum medication (P's stress was not significantly different between the three groups with verum medication. The stress responses in fibrinogen, FVII:C, FXII:C, and D-dimer were similar in all 4 medication groups. The combination of aspirin with propranolol, single aspirin, and single propranolol all attenuated the acute response in plasma VWF:Ag levels to psychosocial stress. This suggests that these cardiovascular drugs might exert limited protection from the development of stress-triggered coronary thrombosis.