Precision and accuracy of fish length measurements obtained with two visual underwater methods

During the VITAL cruise in the Bay of Biscay in summer 2002, two devices for measuring the length of swimming fish were tested: 1) a mechanical crown that emitted a pair of parallel laser beams and that was mounted on the main camera and 2) an underwater auto-focus video camera. The precision and accuracy of these devices were compared and the various sources of measurement errors were estimated by repeatedly measuring fixed and mobile objects and live fish. It was found that fish mobility is the main source of error for these devices because they require that the objects to be measured are perpendicular to the field of vision. The best performance was obtained with the laser method where a video-replay of laser spots (projected on fish bodies) carrying real-time size information was used. The auto-focus system performed poorly because of a delay in obtaining focus and because of some technical problems.

KNOCK DETECTION BY AUDIBLE, ACCELEROMETER, PRESSURE AND IONIC CURRENT METHODS.

This paper describes the ways which are used at the present time by the Ford Motor Company for the detection of knock. A description of the available methods is given, and their relative effectiveness is assessed by analysing data taken simultaneously by all of these methods. It is shown that no one technique has an overwhelming advantage, but that each technique has its individual merits and demerits.

Materials selection in mechanical design

A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimization methods are employed for simultaneous selection of both material and shape.

Phase noise analysis of a mechanical autonomous impact oscillator with a MEMS resonator

In this paper, phase noise analysis of a mechanical autonomous impact oscillator with a MEMS resonator is performed. Since the circuit considered belongs to the class of hybrid systems, methods based on the variational model for the evaluation of either phase noise or steady state solutions cannot be directly applied. As a matter of fact, the monodromy matrix is not defined at impact events in these systems. By introducing saltation matrices, this limit is overcome and the aforementioned methods are extended. In particular, the unified theory developed by Demir is used to analyze the phase noise after evaluating the asymptotically stable periodic solution of the system by resorting to the shooting method. Numerical results are presented to show how noise sources affect the phase noise performances. © 2011 IEEE.

Alternative methods for surface texturing

Surface texturing has a great potential to improve tribological performance. First, possible texturing methods were identified and classified according to their physical principles. In sequence, some alternative texturing methods are presented. Some of them are already currently used either in industry or in laboratory, and innovations or simplifications are described for them. Others are innovative techniques. Some were explored only tentatively, where basic ideas and simple experimental investigations were developed to check their validity. Others were explored in more detail, so that their practical applicability could be identified. The first texturing method was photochemical texturing using a simple and cheap apparatus. Masking with inkjet printing before chemical etching was also successful to texture metallic samples. A new method involving electrochemical texturing, without the need to previously mask the samples to be textured have been studied in terms of voltage, current, mechanical configuration of the apparatus and electrolyte flushing. Another method aims to generate randomly distributed circular pockets on steel surfaces and involves dispersion of small acid droplets in oil. The final method involves the selective formation of hard areas on a steel surface by locallised diffusion, which should then develop into a texture during wear.

Mechanical and chemical bonding properties of ground state BeH2

The crystal structure, mechanical properties and electronic structure of ground state BeH2 are calculated employing the first-principles methods based on the density functional theory. Our calculated structural parameters at equilibrium volume are well consistent with experimental results. Elastic constants, which well obey the mechanical stability criteria, are firstly theoretically acquired. The bulk modulus B, Shear modulus G, Young's modulus E, and Poisson's ratio upsilon are deduced from the elastic constants. The bonding nature in BeH2 is fully interpreted by combining characteristics in band structure, density of states, and charge distribution. The ionicity in the Be-H bond is mainly featured by charge transfer from Be 2s to H 1s atomic orbitals while its covalency is dominated by the hybridization of H 1s and Be 2p states. The Bader analysis of BeH2 and MgH2 are performed to describe the ionic/covalent character quantitatively and we find that about 1.61 (1.6) electrons transfer from each Be (Mg) atom to H atoms.

Quantum Mechanical Study on Tunnelling and Ballistic Transport of Nanometer Si MOSFETs

Using self-consistent calculations of million-atom Schrodinger-Poisson equations, we investigate the I-V characteristics of tunnelling and ballistic transport of nanometer metal oxide semiconductor field effect transistors (MOSFET) based on a full 3-D quantum mechanical simulation under nonequilibtium condition. Atomistic empirical pseudopotentials are used to describe the device Hamiltonian and the underlying bulk band structure. We find that the ballistic transport dominates the I-V characteristics, whereas the effects of tunnelling cannot be neglected with the maximal value up to 0.8mA/mu m when the channel length of MOSFET scales down to 25 nm. The effects of tunnelling transport lower the threshold voltage V-t. The ballistic current based on fully 3-D quantum mechanical simulation is relatively large and has small on-off ratio compared with results derived from the calculation methods of Luo et al.

Extracting nanobelt mechanical properties from nanoindentation

A three-spring-in-series model is proposed for the nanobelt (NB) indentation test. Compared with the previous two-spring-in-series model, which considers the bending stiffness of atomic force microscope cantilever and the indenter/NB contact stiffness, this model adds a third spring of the NB/substrate contact stiffness. NB is highly flexural due to its large aspect ratio of length to thickness. The bending and lift-off of NB form a localized contact with substrate, which makes the Oliver-Pharr method [W. C. Oliver and G. M. Pharr, J. Mater. Res. 7, 1564 (1992)] and Sneddon method [I. N. Sneddon, Int. J. Eng. Sci. 3, 47 (1965)] inappropriate for NB indentation test. Because the NB/substrate deformation may have significant impact on the force-indentation depth data obtained in experiment, the two-spring-in-series model can lead to erroneous predictions on the NB mechanical properties. NB in indentation test can be susceptible to the adhesion influence because of its large surface area to volume ratio. NB/substrate contact and adhesion can have direct and significant impact on the interpretation of experimental data. Through the three-spring-in-series model, the influence of NB/substrate contact and adhesion is analyzed and methods of reducing such influence are also suggested. (C) 2010 American Institute of Physics. [doi:10.1063/1.3432748]

Concise methods for proton radioactivity

Concise methods are proposed to study proton radioactivity. The spectroscopic factor is obtained from relativistic mean field (RMF) theory combined with the BCS method (RMF+BCS). The assault frequency is estimated by a quantum mechanical method considering the structure of the parent nucleus. The penetrability is calculated by the WKB approximation. No additional parameters are introduced. The extracted experimental spectroscopic factors are compared with those from the calculations by the RMF+BCS, and the agreement is good, implying that the present methods work quite well for proton radioactivity. Predictions are provided for some most possible proton emissions, which may be useful for future experiments.

Structure and mechanical properties of Mg-Zn-RE system alloys

The lightest density of Mg has stimulated renewed interest in Mg based alloys for applications in the automotive, aerospace and communications industries. However, Mg in the pure form has relatively low strength, limited ductility and is susceptible to corrosion. Great efforts have been made to improve the mechanical properties of Mg alloys. Alloying Mg with other elements is one of the most important methods. An important class of Mg alloys is the Mg-Zn-RE system (RE = rare earth elements). In recent few decades, a series of new Mg-Zn-RE system alloys have been obtained, and detailed the structure and mechanical properties of the alloys. In this paper, the structure and mechanical properties of the Mg-Zn-RE alloys have been summarized. It showed that these alloys have high strength and they are prospected to be widely used in the future.

Numerical simulation of mesoscopic mechanical behaviors of gradual multi-fiber-reinforced polymer matrix composites

To simulate the deformation and the fracture of gradual multi-fiber-reinforced matrix composites, a numerical simulation method for the mesoscopic mechanical behaviors was developed on the basis of the finite element and the Monte Carlo methods. The results indicate that the strength of a composite increases if the variability of statistical fiber strengths is decreased.