Obtenção e caracterização de nanocelulose a partir de fibras de Chorisia speciosa St. Hil

Natural fibers have been highlighted as a renewable material that can replace materials from oil and its derivatives. In this context, Brazil becomes the perfect setting because of the diversity of fibers found in its territory, such as sugarcane, sisal, rice, cotton, coconut, pineapple, among others. The paineiras (Chorisia speciosa St. Hil) are typically Brazilian trees, which produce paina as fruit. These fruits are still little studied as a source of lignocellulose by research groups. This project aimed obtaining and characterization of cellulose nanofibers from the fibers from the paina fibers. Obtaining nanocellulose is practically made through simplified chemical processes. First, was performed out pre-treatments to removal of waxes, lignin and hemicellulose. The first stage of pre-treatment was carried out by alkaline aqueous solution of sodium hydroxide (NaOH) at 5wt%, where the fibers were under constant agitation for 1h at 70°C. Through alkali treatment it was possible to remove most of the lignin, hemicellulose, waxes and extractives. After the alkaline treatment was done bleaching with an aqueous solution of sodium hydroxide (NaOH) to 4wt% and hydrogen peroxide (H2O2) to 24wt% 1:1 during 2h with constant stirring to 50 °C. Through bleaching was possibe to remove residual lignin, and got cellulose with 72% of crystallinity. Nanocellulose of paina fibers was extracted using different conditions of acid hydrolysis with sulfuric acid (H2SO4) to 50wt%. After acid hydrolysis, the suspensions were centrifuged during 30 min and dialyzed in water to remove excess acid until neutral pH (6-7). Then the suspensions were passed by ultrasonification in an ultrasound 20 kHz during 1h in an ice bath. Untreated, alkalinized and bleached fibers as well as cellulose nanoparticles were characterized by the techniques of thermogravimetry ... (Complete abastract click electronic access below)

Produção de amilases de Rhizopus microsporus var. oligosporus e hidrólise enzimática do bagaço de mandioca visando a produção de etanol por Saccharomyces cerevisiae

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Obtenção e caracterização de nanocelulose a partir de fibras de Chorisia speciosa St. Hil

Natural fibers have been highlighted as a renewable material that can replace materials from oil and its derivatives. In this context, Brazil becomes the perfect setting because of the diversity of fibers found in its territory, such as sugarcane, sisal, rice, cotton, coconut, pineapple, among others. The paineiras (Chorisia speciosa St. Hil) are typically Brazilian trees, which produce paina as fruit. These fruits are still little studied as a source of lignocellulose by research groups. This project aimed obtaining and characterization of cellulose nanofibers from the fibers from the paina fibers. Obtaining nanocellulose is practically made through simplified chemical processes. First, was performed out pre-treatments to removal of waxes, lignin and hemicellulose. The first stage of pre-treatment was carried out by alkaline aqueous solution of sodium hydroxide (NaOH) at 5wt%, where the fibers were under constant agitation for 1h at 70°C. Through alkali treatment it was possible to remove most of the lignin, hemicellulose, waxes and extractives. After the alkaline treatment was done bleaching with an aqueous solution of sodium hydroxide (NaOH) to 4wt% and hydrogen peroxide (H2O2) to 24wt% 1:1 during 2h with constant stirring to 50 °C. Through bleaching was possibe to remove residual lignin, and got cellulose with 72% of crystallinity. Nanocellulose of paina fibers was extracted using different conditions of acid hydrolysis with sulfuric acid (H2SO4) to 50wt%. After acid hydrolysis, the suspensions were centrifuged during 30 min and dialyzed in water to remove excess acid until neutral pH (6-7). Then the suspensions were passed by ultrasonification in an ultrasound 20 kHz during 1h in an ice bath. Untreated, alkalinized and bleached fibers as well as cellulose nanoparticles were characterized by the techniques of thermogravimetry ... (Complete abastract click electronic access below)

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Alternativas de uso da borra de café através de hidrólise ácida, enzimática, ou como substrato para a produção das enzimas: lacase e celulase

In the industrial production of soluble coffee, huge amounts of extracted coffee residues are generated; onaverage, for eachtonne of green coffee extracted, 480 kg of coffee ground waste is produced. This is a solid residue currently used to generate energy at the steam boilers from the soluble coffee industry. Some is also used or as fertilizer on agriculture fields. Seeking a better end use, the work reported here aimed to study the viability of hydrolyzing the coffee ground residue for the production of carbohydrates. Hydrolysis was undertaken with hydrochloric acid at different temperatures and pressures, using a water bath or autoclave.An enzymatic hydrolysis with Viscozyme Lwas developed using Whatman filter paper No1 and the optimal conditions were determined using a rotational central composite experimental design (DCCR).The best conditions to hydrolyze filter paper cellulose were 50 FBG (Fungal β-glucanase) of Viscozyme L at pH 4.0 for 1.0 h and 45 ºC. The ground coffee was hydrolyzed under the same conditions as described above for filter paper, however this enzymatic hydrolysis was not efficient. A combination of enzymatic hydrolysis as a pre-treatment for the ground coffee followed by acid hydrolysis using HCl conducted in an autoclave (120 C for 2.0 h) resulted in higher production of glucose as analyzed by HPLC. Another end use of the ground coffee evaluated was as source of substrate in the culture medium to grow Botryosphaeria rhodina MAMB-05 to produce the enzymes laccase and cellulase. Highest enzyme titres obtained were with 8% (w/v) coffee grounds to which was added a minimum salts medium(Vogel), under agitation conditions (180 rpm) at 28ºC. The phenolic compounds present in the coffee grounds appear to have induced laccase by Botryosphaeria rhodina.

Síntese de ésteres graxos a partir da biomassa da microalga Chlorella sp. por hidrólise “in situ” seguido de esterificação

Neste trabalho, a produção de ésteres graxos da biomassa úmida da microalga Chlorella sp. foi investigada pelo método de hidrólise seguido de esterificação e comparado com o método convencional de extração/transesterificação. Na primeira etapa do processo de hidrólise “in situ” seguido de esterificação ocorreu à hidrólise, onde a água presente na biomassa (50 e 100% em massa) reagiu com os lipídios de reserva, na presença de H2SO4 (20, 40 e 60% em massa), sendo obtidos os ácidos graxos brutos. Na segunda etapa do processo, os ácido graxos foram submetidos à reação de esterificação por 1 ou 4 h na presença de metanol, na razão molar de 30:1 álcool:AG, com H2SO4 10% em massa a 60 ou 100 °C. De acordo com os resultados obtidos no processo de hidrólise/esterificação, os melhores rendimentos – cerca de 7,3±0,8% de FAMEs, em relação a biomassa inicial – foram obtidos na presença de 60% de catalisador e 50% de umidade, na etapa de hidrólise e 100 °C por 4 h na etapa de esterificação. No método convencional de extração-transesterificação, os melhores rendimentos – 7,1±1,8% de FAMEs em relação à biomassa seca – foram obtidos utilizando a mistura de clorofórmio:metanol 2:1 v/v. Em resumo os rendimentos obtidos nos dois métodos de produção de ésteres graxos foram próximos. No entanto, o processo de hidrólise “in situ” seguido de esterificação possui vantagens como a utilização da biomassa úmida.

Síntese de biodiesel etílico de girassol utilizando transesterificação alcalina seguido da adição on pot de H2SO4

No presente trabalho foi investigada a adição on pot de H2SO4 no processo de transesterificação do óleo de girassol com etanol e metanol empregando catalisador alcalino (NaOH e KOH). Após o processo, ocorreu uma eficiente separação tanto do biodiesel etílico como metílico de seus co-produtos. Com a adição on pot de H2SO4 todo sabão formado no meio reacional foi transformado em ácidos graxos livres e o catalisador em sal (Na2SO4 ou K2SO4). A esterificação dos ácidos graxos livres presentes no biodiesel foi aplicada para atingir os padrões de biocombustíveis. Os ácidos graxos contidos no biodiesel foram esterificados na presença de uma mistura com razão molar de 60:1 e 80:1 álcool:ácido graxo, com H2SO4 5 e 10 % em massa. Também foi avaliada a influência da quantidade de catalisador na reação paralela de saponificação. De acordo com os resultados observou-se que a quantidade de sabão formado no processo, variou entre 1,80 e 10,66 % para 1 e 2 % de catalisador, respectivamente. A adição on pot de H2SO4 permitiu aumentar o rendimento de obtenção de biodiesel, e reduziu a geração de efluentes provenientes das lavagens para remoção do sabão, quando comparado com o processo convencional. As análises foram realizadas para avaliar a qualidade do biodiesel, com exceção da estabilidade oxidativa, os demais parâmetros estão de acordo com as normas da ANP. A glicerina foi obtida com uma pureza de 95 % de glicerol com aspecto límpido e incolor, sendo seu principal contaminante o sal proveniente da neutralização do catalisador.

Activación alcalina para mezclas secas

44 p.

Fosfatase ácida e alcalina em solo sob manejo do sistema integração lavoura pecuária e floresta.

2016

Sviluppo di biosensori reagentless basati sull'enzima fosfatasi alcalina

Negli ultimi anni i biosensori enzimatici sono diventati sempre più popolari nel campo delle determinazioni rapide di analiti di interesse industriale ed ambientale. L’utilizzo di tali biosensori consente di evitare, o comunque limitare, l’impiego di metodi analitici basati su tecniche più complesse e dispendiose in termini economici e temporali. Un grande obbiettivo della ricerca negli ultimi anni è quello di costruire biosensori reagentless, ossia dispositivi pronti all’uso da parte degli analisti, indipendentemente dalla loro esperienza. In questo lavoro di tesi sono stati sviluppati dei biosensori amperometrici reagentless che sfruttano l’enzima fosfatasi alcalina (ALP), come elemento di riconoscimento biologico, ed un elettrodo screen-printed (SPE) commerciale, come trasduttore. Per gli elettrodi SPE commerciali sono stati testati modificanti a base di nanomateriali carboniosi e del polimero conduttore PEDOT:ClO4. Sono inoltre stati messi a punto diversi biosensori costruiti utilizzando sia l’enzima ALP immobilizzato che lo stesso enzima in soluzione. I test sono stati eseguiti utilizzando il substrato enzimatico “ascorbil-fosfato di sodio (AAP)” ed alcuni inibitori enzimatici. I dispositivi reagentless sono stati fabbricati mediante stampa 3D e sono stati realizzati appositamente per gli elettrodi SPE commerciali utilizzati. Tali dispositivi sono stati utilizzati per effettuare la determinazione dell’AAP in campo cosmetico e la determinazione dell’enzima ALP in campo alimentare.

EFEITO DA ASSOCIAÇÃO DE PECTINASE, INVERTASE E GLICOSE ISOMERASE NA QUALIDADE DO SUCO DE BANANA

The association of 0,03 % v/w pectinase (Clarex), 0,6 % v/w invertase (Invertase-S) and 0,5 % w/w glucose isomerase (Taka-sweet) in industrialized banana (Musa cavendishii) pulp, under conditions of hydrolysis 40oC, 15 minutes, was observed and compared to other three enzymatic treatements: 0,03 % v/w pectinase (Clarex); 0,03 % v/w pectinase (Clarex) associated to 0,6 % v/w invertase (Invertase-S); and 0,03 % v/w pectinase (Sigma) associated to 0,03 % cellulase (Sigma) to determine the quality using a group of physical, physico-chemical, chemical, microbiological and sensory properties of the banana juices obtained. These properties had not differ significantly in function of pectinases and celulase employed. The addition of invertase had increased sweetness and decreased viscosity in juice. On the other side, the addition of glucose isomerase in inverted juice was not able in increasing significantly fructose content.

Adesão de linhagem selvagem de Streptococcus thermophilus em superfície de aço inoxidável e efeitos da higienização na sua remoção

A wild strain of Streptococcus thermophilus isolated from pasteurized milk was evaluated using an experimental model with respect to its adhesion onto stainless steel surfaces and its behaviour when submitted to cleansing and sanification. In milk, the adhesion of the microorganism on to stainless steel surfaces was studied after 6 hours of contact at 45°C with agitation, and after a cleansing process involving cleaning stages with alkaline and acid detergents followed by sanification, in order to evaluate the resistance of the adhered cells. The microorganism adhered to stainless steel surfaces producing a cell load of 10(4) CFU/cm². After alkaline cleansing, no adhered cells were detected but 6 CFU/cm² were still detected on the surfaces after acid cleansing. Cleansing, followed by sanification with sodium hypochlorite, was sufficient to reduce the load of wild S. thermophilus on the stainless steel surfaces to non-detectable levels. The experimental model proved adequate for the study indicating that the wild microorganism S. thermophilus produces biofilms on stainless steel surfaces. Alkaline cleansing remove more that 99.9% of the adhered cells. The few cells adhered on the surface are removed by acid cleansing demonstrating the need to use different steps and types of detergent for efficient cleansing. The best results for the removal of these biofilms are obtained by using alkaline cleansing followed by acid cleaning, this procedure being more efficient when complemented by sanification with sodium hypochlorite.

Are skeletally mature female rats a suitable model to study osteoporosis?

OBJECTIVE: To analyze if female Wistar rats at 56 weeks of age are a suitable model to study osteoporosis. MATERIALS AND METHODS: Female rats with 6 and 36 weeks of age (n = 8 per group) were kept over a 20-week period and fed a diet for mature rodents complete in terms of Ca, phosphorous, and vitamin D. Excised femurs were measured for bone mass using dual-energy x-ray absorptiometry, morphometry, and biomechanical properties. The following serum mar-kers of bone metabolism were analyzed: parathyroid hormone (PTH), osteocalcin (OC), osteoprotegerin (OPG), receptor activator of nuclear factor Κappa B ligand (RANKL), C-terminal peptides of type I collagen (CTX-I), total calcium, and alkaline phosphatase (ALP) activity. RESULTS: Rats at 56 weeks of age showed important bone metabolism differences when compared with the younger group, such as, highest diaphysis energy to failure, lowest levels of OC, CTX-I, and ALP, and elevated PTH, even with adequate dietary Ca. CONCLUSION: Rats at 26-week-old rats may be too young to study age-related bone loss, whereas the 56-week-old rats may be good models to represent the early stages of age-related changes in bone metabolism.