Preparation of cast aluminium alloy-mica particle composites

The optimum conditions for producing cast aluminium alloy-mica particle composites, by stirring mica particles (40 to 120 mgrm) in molten aluminium alloys (above their liquidus temperatures), followed by casting in permanent moulds, are described. Addition of magnesium either as pieces along with mica particles on the surface of the melts or as a previously added alloying element was found to be necessary to disperse appreciable quantities (1.5 to 2 wt.%) of mica particles in the melts and retain them as uniform dispersions in castings under the conditions of present investigation. These castings can be remelted and degassed with nitrogen at least once with the retention of about 80% mica particles in the castings. Electron probe micro-analysis of these cast composites showed that magnesium added to the surface of the melt along with mica has a tendency to segregate around the mica particles, apparently improving the dispersability for mica particles in liquid aluminium alloys. The mechanical properties of the aluminium alloy-mica particle composite decrease with an increase in mica content, however, even at 2.2% the composite has a tensile strength of 14.22 kg mm–2 with 1.1% elongation, a compression strength of 42.61 kg mm–2, and an impact strength of 0.30 kgm cm–2. The properties are adequate for certain bearing applications, and the aluminium-mica composite bearings were found to run under boundary lubrication, semi-dry and dry friction conditions whereas the matrix alloy (without mica) bearings seized or showed stick slip under the same conditions.

The effect of temperature on height growth of Scots pine in northern Finland

The effect of temperature on height growth of Scots pine in the northern boreal zone in Lapland was studied in two different time scales. Intra-annual growth was monitored in four stands in up to four growing seasons using an approximately biweekly measurement interval. Inter-annual growth was studied using growth records representing seven stands and five geographical locations. All the stands were growing on a dry to semi-dry heath that is a typical site type for pine stands in Finland. The applied methodology is based on applied time-series analysis and multilevel modelling. Intra-annual elongation of the leader shoot correlated with temperature sum accumulation. Height growth ceased when, on average, 41% of the relative temperature sum of the site was achieved (observed minimum and maximum were 38% and 43%). The relative temperature sum was calculated by dividing the actual temperature sum by the long-term mean of the total annual temperature sum for the site. Our results suggest that annual height growth ceases when a location-specific temperature sum threshold is attained. The positive effect of the mean July temperature of the previous year on annual height increment proved to be very strong at high latitudes. The mean November temperature of the year before the previous had a statistically significantly effect on height increment in the three northernmost stands. The effect of mean monthly precipitation on annual height growth was statistically insignificant. There was a non-linear dependence between length and needle density of annual shoots. Exceptionally low height growth results in high needle-density, but the effect is weaker in years of average or good height growth. Radial growth and next year s height growth are both largely controlled by current July temperature. Nevertheless, their growth variation in terms of minimum and maximum is not necessarily strongly correlated. This is partly because height growth is more sensitive to changes in temperature. In addition, the actual effective temperature period is not exactly the same for these two growth components. Yet, there is a long-term balance that was also statistically distinguishable; radial growth correlated significantly with height growth with a lag of 2 years. Temperature periods shorter than a month are more effective variables than mean monthly values, but the improvement is on the scale of modest to good when applying Julian days or growing-degree-days as pointers.

First report of shoot blight of persimmon caused by Diaporthe neotheicola in Australia

Shoot blight symptom was found on persimmon (Diospyros kaki) in southern Western Australia in December 2010. The pathogen was isolated and identified as Diaporthe neotheicola on the basis of morphology, sequence analysis of the internal transcribed spacer (ITS) and the translation elongation factor 1-α (TEF). A pathogenicity test was conducted and Koch's postulates were fulfilled by re-isolation of the fungus from diseased tissues. This is the first report of D. neotheicola causing shoot blight on persimmon in Australia and worldwide. © 2012 Australasian Plant Pathology Society Inc.

A phylogenetic and taxonomic re-evaluation of the Bipolaris - Cochliobolus - Curvularia Complex

Three genera, Cochliobolus, Bipolaris and Curvularia form a complex that contains many plant pathogens, mostly on grasses (Poaceae) with a worldwide distribution. The taxonomy of this complex is confusing as frequent nomenclatural changes and refinements have occurred. There is no clear morphological boundary between the asexual genera Bipolaris and Curvularia, and some species show intermediate morphology. We investigated this complex based on a set of ex-type cultures and collections from northern Thailand. Combined gene analysis of rDNA ITS (internal transcribed spacer), GPDH (glyceraldehyde 3-phosphate dehydrogenase), LSU (large subunit) and EF1-α (translation elongation factor 1-α) shows that this generic complex divides into two groups. Bipolaris and Cochliobolus species clustered in Group 1 along with their type species, whereas Curvularia species (including species named as Bipolaris, Cochliobolus and Curvularia) clustered in Group 2, with its generic type. The nomenclatural conflict in this complex is resolved giving priority to the more commonly used established generic names Bipolaris and Curvularia. Modern descriptions of the genera Bipolaris and Curvularia are provided and species resolved in this study are transferred to one of these genera based on their phylogeny. © 2012 Mushroom Research Foundation.

Preparation and characterization of potato starch films plasticized with polyols

The present study investigated the potato starches and polyols which were used to prepare edible films. The amylose content and the gelatinization properties of various potato starches extracted from different potato cultivars were determined. The amylose content of potato starches varied between 11.9 and 20.1%. Onset temperatures of gelatinization of potato starches in excess water varied independently of the amylose content from 58 to 61°C determined using differential scanning calorimetry (DSC). The crystallinity of selected native starches with low, medium and high amylose content was determined by X-ray diffraction. The relative crystallinity was found to be around 10 13% in selected native potato starches containing 13 17% water. The glass transition temperature, crystallization melting behavior and relaxations of polyols, erythritol, sorbitol and xylitol, were determined using (DSC), dielectric analysis (DEA) and dynamic mechanical analysis (DMA). The glass transition temperatures of xylitol and sorbitol decreased as a result of water plasticization. Anhydrous amorphous erythritol crystallized rapidly. Edible films were obtained from solutions containing gelatinized starch, plasticizer (polyol or binary polyol mixture) and water by casting and evaporating water at 35°C. The present study investigated effects of plasticizer type and content on physical and mechanical properties of edible films stored at various relative water vapor pressures (RVP). The crystallinity of edible films with low, medium and high amylose content was determined by X-ray diffraction and they were found to be practically amorphous. Water sorption and water vapor permeability (WVP) of films was affected by the type and content of plasticizer. Water vapor permeability of films increased with increasing plasticizer content and storage RVP. Generally, Young's modulus and tensile strength decreased with increasing plasticizer and water content with a concurrent increase in elongation at break of films. High contents of xylitol and sorbitol resulted in changes in physical and mechanical properties of films probably due to phase separation and crystallization of xylitol and sorbitol which was not observed when binary polyol mixtures were used as plasticizers. The mechanical properties and the water vapor permeability (WVP) of the films were found to be independent of the amylose content.

Mannans as film formers and emulsion stabilizers

Mannans are abundant plant polysaccharides found in the endosperm of certain leguminous seeds (guar gum galactomannan, GG; locust bean gum galactomannan, LBG), in the tuber of the konjac plant (konjac glucomannan, KGM), and in softwoods (galactoglucomannan, GGM). This study focused on the effects of the chemical structure of mannans on their film-forming and emulsion-stabilizing properties. Special focus was on spruce GGM, which is an interesting new product from forest biorefineries. A plasticizer was needed for the formation of films from mannans other than KGM and the optimal proportion was 40% (w/w of polymers) glycerol or sorbitol. Galactomannans with lower galactose content (LBG, modified GG) produced films with higher elongation at break and tensile strength. The mechanical properties of GG-based films were improved by decreasing the degree of polymerization of the polysaccharide with moderate mannanase treatments. The improvement of mechanical properties of GGM-based films was sought by blending GGM with each of poly(vinyl alcohol) (PVOH), corn arabinoxylan (cAX), and KGM. Adding other polymers increased the elongation at break of GGM blend films. The tensile strength of films increased with increasing amounts of PVOH and KGM, but the effect of cAX was the opposite. Dynamic mechanical analysis showed two separate loss modulus peaks for blends of GGM and PVOH, but a single peak for all other films. Optical and scanning electron microscopy confirmed good miscibility of GGM with cAX and KGM. In contrast, films blended from GGM and PVOH showed phase separation. GGM and KGM were mixed with cellulose nanowhiskers (CNW) to form composite films. Addition of CNW to KGM-based films induced the formation of fiberlike structures with lengths of several millimeters. In GGM-based films, rodlike structures with lengths of tens of micrometers were formed. Interestingly, the notable differences in the film structure did not appear to be related to the mechanical and thermal properties of the films. Permeability properties of GGM-based films were compared to those of films from commercial mannans KGM, GG, and LBG. GGM-based films had the lowest water vapor permeability when compared to films from other mannans. The oxygen permeability of GGM films was of the same magnitude as that of commercial polyethylene / ethylene vinyl alcohol / polyethylene laminate film. The aroma permeability of GGM films was low. All films were transparent in the visible region, but GGM films blocked the light transmission in the ultraviolet region of the spectra. The stabilizing effect of GGM on a model beverage emulsion system was studied and compared to that of GG, LBG, KGM, and cAX. In addition, GG was enzymatically modified in order to examine the effect of the degree of polymerization and the degree of substitution of galactomannans on emulsion stability. Use of GGM increased the turbidity of emulsions both immediately after preparation and after storage of up to 14 days at room temperature. GGM emulsions had higher turbidity than the emulsions containing other mannans. Increasing the storage temperature to +45 ºC led to rapid emulsion breakdown, but a decrease in storage temperature increased emulsion stability after 14 days. A low degree of polymerization and a high degree of substitution of the modified galactomannans were associated with a decrease in emulsion turbidity.

Interaction of Gibberellic Acid and Indole-3-acetic Acid in the Growth of Excised Cuscuta Shoot Tips in Vitro1

Gibberellic acid (GA3) induced a marked elongation of 2.5-centimeter shoot tips of Cuscuta chinensis Lamk. cultured in vitro. In terms of the absolute amount of elongation, this growth may be the largest reported for an isolated plant system. The response to hormone was dependent on an exogenous carbohydrate supply. The hormone-stimulated growth was due to both cell division and cell elongation. The growth response progressively decreased if GA3 was given at increasingly later times after culturing, but the decreased growth response could be restored by the application of indole-3-acetic acid (IAA) to the apex. Explants deprived of GA3 gradually lost their ability to transport IAA basipetally, but this ability was also restored by auxin application. The observations are explained on the basis that: (a) the growth of Cuscuta shoot tip in vitro requires, at least, both an auxin and a gibberellin; and (b) in the absence of gibberellin the cultured shoot tip explants lose the ability to produce and/or transport auxin.

Phyllosticta spp. on cultivated Citrus in Australia

The occurrence of pathogenic and endophytic species of Phyllosticta on cultivated Citrus in Australia was investigated by DNA sequence analysis of specimens held in plant pathology herbaria and culture collections. Sequences of the internal transcribed spacer region (ITS1, 5.8S, ITS2), and partial translation elongation factor 1-alpha (TEF) gene of 41 Phyllosticta-like isolates from Citrus were compared to those sequences from the type specimens of Phyllosticta recorded from around the world. Phylogenetic analysis resolved all the sequences of Australian accessions into two major clades. One clade corresponded to P. citricarpa, which causes citrus black spot disease. The other clade contained P. capitalensis, which is a known endophyte of Citrus and many other plant species. All included herbarium accessions previously designated as Guignardia mangiferae are now designated P. capitalensis. No Australian isolates were identified as the newly described pathogens of citrus P. citriasiana or P. citrichinaensis, or the endophytes Guignarida mangiferae, P. brazilianiae, or P. citribraziliensis. © 2013 Australasian Plant Pathology Society Inc.

Molecular phylogenetic analysis reveals six new species of Diaporthe from Australia

Six new species of Diaporthe, D. beilharziae on Indigofera australis, D. fraxini-angustifoliae on Fraxinus angustifolia subsp. oxycarpa, D. litchicola on Litchi chinensis, D. nothofagi on Nothofagus cunninghamii, D. pascoei on Persea americana and D. salicicola on Salix purpurea from Australia are described and illustrated based on morphological characteristics and molecular analyses. Three of the new species no longer produced sporulating structures in culture and two of these were morphologically described from voucher specimens. Phylogenetic relationships of the new species with other Diaporthe species are revealed by DNA sequence analyses based on the internal transcribed spacer (ITS) region, and partial regions of the β-tubulin (BT) and translation elongation factor 1-alpha (TEF). © 2013 Mushroom Research Foundation.

Deformation characterization of superplastic AA7475 alloy

AA7475 alloy was deformed up to 25% elongation in INSTRON at 788K. The grain boundary sliding due to this superplastic deformation was measured by Scanning Electron Microscope. The microstructure and texture development due to this deformation at elevated temperature was analyzed from the Orientation Image Microstructures i.e. the Electron Back Scattered Diffraction Image. The Orientation Image Microstructures revealed that superplastic deformation was associated with recovery and recrystallization in-situ process.

Phyllosticta species on orchids (Orchidaceae), introducing Phyllosticta speewahensis sp. nov. (Phyllostictaceae, Ascomycota) from northern Australia

Several species of Phyllosticta (syn. Guignardia) have been described from orchids worldwide. A new species, Phyllosticta speewahensis, is proposed for a specimen isolated from leaf spots on a hybrid Vanda orchid in northern Queensland, Australia. Phylogenetic analysis of the nrDNA internal transcribed spacer region (ITS) and partial translation elongation factor 1-alpha (TEF1) gene sequences showed that P. speewahensis is most closely related to P. hostae. The likelihood that orchids harbour further cryptic species of endophytic and pathogenic Phyllosticta species is discussed.

Polyphasic characterization of four new plant pathogenic Phyllosticta species from China, Japan, and the United States

The black rot disease of Vitis species and other host genera of Vitacease is caused by Phyllosticta ampelicida and allied taxa which is considered to be a species complex. In this paper, we introduce four new species of Phyllosticta, including two from the P. ampelicida complex, based on a polyphasic characterization including disease symptoms and host association, morphology, and molecular phylogeny. The phylogenetic analysis was conducted based on the ribosomal internal transcribed spacer (ITS) region and a combined multi-locus alignment of the ITS, actin (ACT), partial translation elongation factor 1-alpha (TEF-1), and glyceraldehydes 3-phosphate dehydrogenase (GPDH) gene regions. Our study confirms the phylogenetic distinctions of the four new species, as well as their phenotypic differences with known species in the genus.

Green and brown bridges between weeds and crops reveal novel Diaporthe species in Australia

Diaporthe (syn. Phomopsis) species are well-known saprobes, endophytes or pathogens on a range of plants. Several species have wide host ranges and multiple species may sometimes colonise the same host species. This study describes eight novel Diaporthe species isolated from live and/or dead tissue from the broad acre crops lupin, maize, mungbean, soybean and sunflower, and associated weed species in Queensland and New South Wales, as well as the environmental weed bitou bush (Chrysanthemoides monilifera subsp. rotundata) in eastern Australia. The new taxa are differentiated on the basis of morphology and DNA sequence analyses based on the nuclear ribosomal internal transcribed spacer region, and part of the translation elongation factor-1α and ß-tubulin genes. The possible agricultural significance of live weeds and crop residues ('green bridges') as well as dead weeds and crop residues ('brown bridges') in aiding survival of the newly described Diaporthe species is discussed.

Starch composites with aconitic acid

The aim of this project is to examine the effectiveness of using aconitic acid (AcA), a tricarboxylic acid which contains a carbon/carbon double bond (C=C), to enhance the properties of starch-based films. Starch/glycerol cast films were prepared with 0, 2, 5, 10 and 15 wt% AcA (starch wt% basis) and the properties analysed. It was shown that AcA acted as both a cross-linking agent and also a strong plasticising agent. The 5 wt% AcA derived starch films were the most effectively cross-linked having the lowest solubility (28 wt%) and decreased swelling coefficient (35 vol.%) by approximately 3 times and 2.4 times respectively compared to the control film submerged in water (23 °C). There was also a significant increase in the film elongation at break by approximately 35 times (compared to the control) with the addition of 15 wt% AcA, emphasising the plasticising effect of AcA. However, generally there was a reduced tensile strength, softening of the film, and reduced thermal stability with increased amounts of AcA.

Rate of ribonucleic acid chain growth in Mycobacterium tuberculosis H37Rv.

Two methods were employed to measure the rate of ribonucleic acid (RNA) chain growth in vivo in Mycobacterium tuberculosis H37Rv cultures growing in Sauton medium at 37 degrees C, with a generation time of 10 h. In the first, the bacteria were allowed to assimilate [3H]uracil or [3H]guanine into their RNA for short time periods. The RNA was then extracted and hydrolyzed with alkali, and the radioactivity in the resulting nucleotides and nucleosides was measured. The data obtained by this method allowed the calculation of the individual nucleotide step times during the growth of RNA chains, from which the average rate of RNA chain elongation was estimated to be about 4 nucleotides per s. The second method employed the antibiotic rifampin, which specifically inhibits the initiation of RNA synthesis without interfering with the elongation and completion of nascent RNA chains. Usint this method, the transcription time of the 16S, 23S, and 5S ribosomal RNA genes was estimated to be 7.6 min, which corresponds to a ribosomal RNA chain growth rate of 10 nucleotides per s.