Immersion enthalpy variation of surface-modified mineral activated carbon in lead (II) aqueous solution adsorption: the relation between immersion enthalpy and adsorption capacity

An activated carbon was obtained by chemical activation with phosphoric acid, CM, from a mineral carbon. Afterwards, the carbon was modified with 2 and 5 molL-1, CMox2 and CMox5 nitric acid solutions to increase the surface acid group contents. Immersion enthalpy at pH 4 values and Pb2+ adsorption isotherms were determined by immersing activated carbons in aqueous solution. The surface area values of the adsorbents and total pore volume were approximately 560 m².g-1 and 0.36 cm³g-1, respectively. As regards chemical characteristics, activated carbons had higher acid sites content, 0.92-2.42 meq g-1, than basic sites, 0.63-0.12 meq g-1. pH values were between 7.4 and 4.5 at the point of zero charge, pH PZC. The adsorbed quantity of Pb2+ and the immersion enthalpy in solution of different pH values for CM activated carbon showed that the values are the highest for pH 4, 15.7 mgg-1 and 27.6 Jg-1 respectively. Pb2+ adsorption isotherms and immersion enthalpy were determined for modified activated carbons and the highest values were obtained for the activated carbon that showed the highest content of total acid sites on the surface.

Role of oxidation-reduction cycle of iron in direct leaching of zinc concentrate

Direct leaching is an alternative to conventional roast-leach-electrowin (RLE) zinc production method. The basic reaction of direct leach method is the oxidation of sphalerite concentrate in acidic liquid by ferric iron. The reaction mechanism and kinetics, mass transfer and current modifications of zinc concentrate direct leaching process are considered. Particular attention is paid to the oxidation-reduction cycle of iron and its role in direct leaching of zinc concentrate, since it can be one of the limiting factors of the leaching process under certain conditions. The oxidation-reduction cycle of iron was experimentally studied with goal of gaining new knowledge for developing the direct leaching of zinc concentrate. In order to obtain this aim, ferrous iron oxidation experiments were carried out. Affect of such parameters as temperature, pressure, sulfuric acid concentration, ferrous iron and copper concentrations was studied. Based on the experimental results, mathematical model of the ferrous iron oxidation rate was developed. According to results obtained during the study, the reaction rate orders for ferrous iron concentration, oxygen concentration and copper concentration are 0.777, 0.652 and 0.0951 respectively. Values predicted by model were in good concordance with the experimental results. The reliability of estimated parameters was evaluated by MCMC analysis which showed good parameters reliability.

Highly sensitive spectrophotometric methods for the determination of olanzapine

Highly sensitive and selective spectrophotometric methods (A and B) were developed for the determination of micro amounts of olanzapine (OLZ). Method A (direct method) is based on the oxidation of olanzapine with a known excess of iodine monochloride (ICl) in an acidic medium. Under the same condition, thymol blue was iodinated by unreacted ICl, and the absorbance of uniodinated thymol blue was measured at 536 nm. The decrease in ICl concentration is a measure of drug concentration. In method B (indirect method), oxidation of OLZ by a known excess of Ce(IV) in sulfuric acid medium followed by the reaction of unreacted Ce(IV) with leuco crystal violet (LCV) to crystal violet (CV), which is measured in an acetate buffer medium ( pH 4.9) at 580 nm. These methods obey the Beer's law in the concentration range of 0.2-1.6 µg mL-1 (method A) and 0.1-1.4 µg mL-1 (method B). The developed procedures have been successfully applied to the determination of OLZ in pure and in dosage forms. The results exhibit no interference from the presence of excipients. The reliability of the methods was established by parallel determination of OLZ against the reference method.

Synthesis of percarboxylic acids in microreactor

Percarboxylic acids are commonly used as disinfection and bleaching agents in textile, paper, and fine chemical industries. All of these applications are based on the oxidative potential of these compounds. In spite of high interest in these chemicals, they are unstable and explosive chemicals, which increase the risk of synthesis processes and transportation. Therefore, the safety criteria in the production process should be considered. Microreactors represent a technology that efficiently utilizes safety advantages resulting from small scale. Therefore, microreactor technology was used in the synthesis of peracetic acid and performic acid. These percarboxylic acids were produced at different temperatures, residence times and catalyst i.e. sulfuric acid concentrations. Both synthesis reactions seemed to be rather fast because with performic acid equilibrium was reached in 4 min at 313 K and with peracetic acid in 10 min at 343 K. In addition, the experimental results were used to study the kinetics of the formation of performic acid and peracetic acid. The advantages of the microreactors in this study were the efficient temperature control even in very exothermic reaction and good mixing due to the short diffusion distances. Therefore, reaction rates were determined with high accuracy. Three different models were considered in order to estimate the kinetic parameters such as reaction rate constants and activation energies. From these three models, the laminar flow model with radial velocity distribution gave most precise parameters. However, sulfuric acid creates many drawbacks in this synthesis process. Therefore, a ´´greener´´ way to use heterogeneous catalyst in the synthesis of performic acid in microreactor was studied. The cation exchange resin, Dowex 50 Wx8, presented very high activity and a long life time in this reaction. In the presence of this catalyst, the equilibrium was reached in 120 second at 313 K which indicates a rather fast reaction. In addition, the safety advantages of microreactors were investigated in this study. Four different conventional methods were used. Production of peracetic acid was used as a test case, and the safety of one conventional batch process was compared with an on-site continuous microprocess. It was found that the conventional methods for the analysis of process safety might not be reliable and adequate for radically novel technology, such as microreactors. This is understandable because the conventional methods are partly based on experience, which is very limited in connection with totally novel technology. Therefore, one checklist-based method was developed to study the safety of intensified and novel processes at the early stage of process development. The checklist was formulated using the concept of layers of protection for a chemical process. The traditional and three intensified processes of hydrogen peroxide synthesis were selected as test cases. With these real cases, it was shown that several positive and negative effects on safety can be detected in process intensification. The general claim that safety is always improved by process intensification was questioned.

Lignoselluloosapohjaisten väkevähappohydrolysaattien jatkuvatoiminen kromatografinen fraktiointi

Työssä tutkittiin lignoselluloosapohjaisten väkevähappohydrolysaattien (monosakkaridit, rikki- ja etikkahppo) jatkuvatoimista kromatografista fraktiointia käyttäen Japan Organo SMB -prosessia. Adsorbenttinä toimi happomuotoinen (H+) vahva kationinvaihtohartsi. Panostoimista fraktiointia käytettiin vertailukohtana. Jatkuvatoimisen prosessin optimoinnilla saavutettiin monosakkaridien suurimmaksi tuottavuudeksi 283 mol/(m3 h) (panosprosessille 145 mol/(m3 h). JO-prosessilla saavutettiin korkeat rikki- ja etikkahapon saannot: 97,3 % ja 93,5 %. Monosakkaridisaanto jäi hieman alhaisemmaksi (61,7 %) johtuen monosakkaridi- ja rikkihappo-profiilien hankalasta erottamisesta. Ulostulo virtojen puhtaudet olivat korkeat: 89 % monosakkarideille, 89 % rikkihapolle ja 100 % etikkahapolle.

Metallien eluointi kelatoivasta ioninvaihtimesta

Kelatoivat ioninvaihtimet ovat yleensä makrohuokoisia hartseja, joiden avulla metalleja poistetaan ja otetaan mahdollisesti talteen teollisuuden puhdistettavista jätevirroista. Ne muodostavat metalli-ionien kanssa komplekseja runkomateriaaliin kovalenttisesti liitettyjen aktiivisten funktionaalisten ryhmiensä välityksellä. Ioninvaihtimen selektiivisyys eri metalli-ioneja kohtaan vaihtelee riippuen siihen liitetystä kelatoivasta ryhmästä. Työssä tutkitaan metallien tarttumista kelatoiviin ioninvaihtimiin, sekä niiden eluoitumista adsorbentistaan. Kelatoivat ioninvaihtimet sitovat metalli-ioneja tehokkaasti ligandiensa monihampaisuudesta johtuen. Metallien tarttuminen kelatoivaan ioninvaihtimeen ei kuitenkaan ole yksiselitteistä, vaan siihen vaikuttaa muun muassa pH yhdessä monen muun tekijän kanssa. Ioninvaihtimien selektiivisyyttä tarkastellaan työssä lähinnä kovien ja pehmeiden happojen ja emästen HSAB -teorian näkökulmasta. Regeneroinnilla ioninvaihdin saadaan jälleen alkuperäiseen muotoonsa, minkä jälkeen se voidaan käyttää uudelleen. Yleensä regenerointi suoritetaan kemiallisesti. Tässä työssä ioninvaihtimien regenerointia ja kohdemetallin eluointia tarkastellaan paitsi teoriassa, myös kokeellisessa osuudessa. Kokeellisessa osuudessa tutkitaan kuparin (Cu2+) eluoitumista kelatoivasta Dowex M-4195 kationinvaihtohartsista. Kokeissa hartsi ladattiin kuparilla erillisessä panoksessa kuparin ollessa syöttöliuoksessa kuparisulfaattina. Eluointiliuoksina käytettiin 2 ja 5 molaarista rikkihappoa, sekä 2 molaarista ammoniumhydroksidia. Eluointi suoritettiin panostoimisena kolonniajona ja eluaatista otetut näytteet analysoitiin atomiadsorptiospektrofotometrillä. Analyysitulokset esitetään läpäisykäyrinä, joiden perusteella 2M ammoniumhydroksidi on kolmesta tutkitusta eluentista tehokkain eluoimaan kuparia Dowex M-4195 hartsista.

Chromatographic recovery of chemicals from acidic biomass hydrolysates

Lignocellulosic biomasses (e.g., wood and straws) are a potential renewable source for the production of a wide variety of chemicals that could be used to replace those currently produced by petrochemical industry. This would lead to lower greenhouse gas emissions and waste amounts, and to economical savings. There are many possible pathways available for the manufacturing of chemicals from lignocellulosic biomasses. One option is to hydrolyze the cellulose and hemicelluloses of these biomasses into monosaccharides using concentrated sulfuric acid as catalyst. This process is an efficient method for producing monosaccharides which are valuable platforn chemicals. Also other valuable products are formed in the hydrolysis. Unfortunately, the concentrated acid hydrolysis has been deemed unfeasible mainly due to high chemical consumption resulting from the need to remove sulfuric acid from the obtained hydrolysates prior to the downstream processing of the monosaccharides. Traditionally, this has been done by neutralization with lime. This, however, results in high chemical consumption. In addition, the by-products formed in the hydrolysis are not removed and may, thus, hinder the monosaccharide processing. In order to improve the feasibility of the concentrated acid hydrolysis, the chemical consumption should be decreased by recycling of sulfuric acid without neutralization. Furthermore, the monosaccharides and the other products formed in the hydrolysis should be recovered selectively for efficient downstream processing. The selective recovery of the hydrolysis by-products would have additional economical benefits on the process due to their high value. In this work, the use of chromatographic fractionation for the recycling of sulfuric acid and the selective recovery of the main components from the hydrolysates formed in the concentrated acid hydrolysis was investigated. Chromatographic fractionation based on the electrolyte exclusion with gel type strong acid cation exchange resins in acid (H+) form as a stationary phase was studied. A systematic experimental and model-based study regarding the separation task at hand was conducted. The phenomena affecting the separation were determined and their effects elucidated. Mathematical models that take accurately into account these phenomena were derived and used in the simulation of the fractionation process. The main components of the concentrated acid hydrolysates (sulfuric acid, monosaccharides, and acetic acid) were included into this model. Performance of the fractionation process was investigated experimentally and by simulations. Use of different process options was also studied. Sulfuric acid was found to have a significant co-operative effect on the sorption of the other components. This brings about interesting and beneficial effects in the column operations. It is especially beneficial for the separation of sulfuric acid and the monosaccharides. Two different approaches for the modelling of the sorption equilibria were investigated in this work: a simple empirical approach and a thermodynamically consistent approach (the Adsorbed Solution theory). Accurate modelling of the phenomena observed in this work was found to be possible using the simple empirical models. The use of the Adsorbed Solution theory is complicated by the nature of the theory and the complexity of the studied system. In addition to the sorption models, a dynamic column model that takes into account the volume changes of the gel type resins as changing resin bed porosity was also derived. Using the chromatography, all the main components of the hydrolysates can be recovered selectively, and the sulfuric acid consumption of the hydrolysis process can be lowered considerably. Investigation of the performance of the chromatographic fractionation showed that the highest separation efficiency in this separation task is obtained with a gel type resin with a high crosslinking degree (8 wt. %); especially when the hydrolysates contain high amounts of acetic acid. In addition, the concentrated acid hydrolysis should be done with as low sulfuric acid concentration as possible to obtain good separation performance. The column loading and flow rate also have large effects on the performance. In this work, it was demonstrated that when recycling of the fractions obtained in the chromatographic fractionation are recycled to preceding unit operations these unit operations should included in the performance evaluation of the fractionation. When this was done, the separation performance and the feasibility of the concentrated acid hydrolysis process were found to improve considerably. Use of multi-column chromatographic fractionation processes, the Japan Organo process and the Multi-Column Recycling Chromatography process, was also investigated. In the studied case, neither of these processes could compete with the single-column batch process in the productivity. However, due to internal recycling steps, the Multi-Column Recycling Chromatography was found to be superior to the batch process when the product yield and the eluent consumption were taken into account.

Permuurahaishapon valmistaminen mikroreaktorissa

Kandidaatintyön teoriaosassa perehdytään mikroreaktoreihin sekä niiden etuihin ja haasteisiin. Lisäksi esitellään lyhyesti, kuinka sekoitus näissä reaktoreissa voidaan järjestää erilaisten sekoituselementtien avulla sekä uusien ainetta lisäävien valmistusmenetelmien tarjoamat mahdollisuudet reaktorien valmistukselle. Mikroreaktorien edut liittyvät pääasiassa prosessin helpompaan hallittavuuteen, mikä johtaa mm. turvallisuuden lisääntymiseen ja energiasäästöihin. Lisäksi esitellään kokeellisessa osassa lähtöaineina käytettävät vetyperoksidi ja muurahaishappo, sekä tuotteena syntyvä permuurahaishappo ja sen käyttökohteita. Permuurahaishappoa käytetään mm. desinfiointiaineiden yhtenä komponenttina. Sitä voidaan käyttää myös paperikoneen vesikierron bakteerien tappamiseen. Epästabiiliutensa vuoksi permuurahaishappo voi räjähtää jopa huoneenlämmössä, mikä aiheuttaa merkittävän riskin sen varastoinnille ja kuljetukselle. Tästä syystä työssä tutkittu menetelmä permuurahaishapon valmistamiseksi mikroreaktorissa tarjoaa hyvän vaihtoehdon permuurahaishapon tuottamiseksi suoraan tarpeeseen. Kokeellisessa osassa permuurahaishappoa valmistettiin muurahaishaposta ja vetyperoksidista käyttäen rikkihappoa katalyyttinä reaktion nopeuttamiseksi. Lämpötilan ja viipymäajan vaikutusta tutkittiin permuurahaishapon muodostumiseen. Molempien nosto vaikutti edullisesti permuurahaishapon saantoon, mutta lämpötilan nosto lisää samalla räjähdysriskiä. Mikroreaktorissa lämpötilan nosto on kuitenkin suhteessa turvallisempaa makroreaktoriin verrattuna.

Comparison of methodologies for moisture determination on dried bee pollen samples

Bee pollen moisture value is one of the quality parameters for this product. Some countries such as Argentina, Brazil, Bulgaria, Poland and Switzerland have bee pollen regulations on quality parameters, but these are not clear regarding which method should be used for moisture determination. The aim of this paper was to compare six methods of moisture determination in dried bee pollen samples. The methods were: conventional oven at 100 °C, vacuum oven at 70 °C, desiccator with sulfuric acid, drying out process with infrared light at 85 °C, lyophilization and Karl Fisher's method. Based on the results, the best methods for moisture determination of bee pollen were the drying process with infrared and the lyophilization, since these have shown lower moisture values.

The role of metal ions in selective and sustainable processes

Sustainability and recycling are core values in today’s industrial operations. New materials, products and processes need to be designed in such a way as to consume fewer of the diminishing resources we have available and to put as little strain on the environment as possible. An integral part of this is cleaning and recycling. New processes are to be designed to improve the efficiency in this aspect. Wastewater, including municipal wastewaters, is treated in several steps including chemical and mechanical cleaning of waters. Well-cleaned water can be recycled and reused. Clean water for everyone is one of the greatest challenges we are facing today. Ferric sulphate, made by oxidation from ferrous sulphate, is used in water purification. The oxidation of ferrous sulphate, FeSO4, to ferric sulphate in acidic aqueous solutions of H2SO4 over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and several catalysts were screened: active carbon, active carbon impregnated with Pt, Rh, Pd and Ru. Both active carbon and noble metal-active carbon catalysts enhanced the oxidation rate considerably. The order of the noble metals according to the effect was: Pt >> Rh > Pd, Ru. By the use of catalysts, the production capacities of existing oxidation units can be considerably increased. Good coagulants have a high charge on a long polymer chain effectively capturing dirty particles of the opposite charge. Analysis of the reaction product indicated that it is possible to obtain polymeric iron-based products with good coagulation properties. Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60B100°C and 4B10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe2+ to Fe3+ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe2+ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe2+ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe2+ over active carbon and active carbon-noble metal catalysts. Engineering aspects were closely considered and effort was directed to utilizing existing equipment in the production of the new coagulant. Ferrous sulphate can be catalytically oxidized to produce a novel long-chained polymeric iron-based flocculent in an easy and affordable way in existing facilities. The results can be used for modelling the reactors and for scale-up. Ferric iron (Fe3+) was successfully applied for the dissolution of sphalerite. Sphalerite contains indium, gallium and germanium, among others, and the application can promote their recovery. The understanding of the reduction process of ferric to ferrous iron can be used to develop further the understanding of the dissolution mechanisms and oxidation of ferrous sulphate. Indium, gallium and germanium face an ever-increasing demand in the electronics industry, among others. The supply is, however, very limited. The fact that most part of the material is obtained through secondary production means that real production quota depends on the primary material production. This also sets the pricing. The primary production material is in most cases zinc and aluminium. Recycling of scrap material and the utilization of industrial waste, containing indium, gallium and geranium, is a necessity without real options. As a part of this study plausible methods for the recovery of indium, gallium and germanium have been studied. The results were encouraging and provided information about the precipitation of these valuables from highly acidic solutions. Indium and gallium were separated from acidic sulphuric acid solutions by precipitation with basic sulphates such as alunite or they were precipitated as basic sulphates of their own as galliunite and indiunite. Germanium may precipitate as a basic sulphate of a mixed composition. The precipitation is rapid and the selectivity is good. When the solutions contain both indium and gallium then the results show that gallium should be separated before indium to achieve a better selectivity. Germanium was separated from highly acidic sulphuric acid solutions containing other metals as well by precipitating with tannic acid. This is a highly selective method. According to the study other commonly found metals in the solution do not affect germanium precipitation. The reduction of ferric iron to ferrous, the precipitation of indium, gallium and germanium, and the dissolution of the raw materials are strongly depending on temperature and pH. The temperature and pH effect were studied and which contributed to the understanding and design of the different process steps. Increased temperature and reduced pH improve the reduction rate. Finally, the gained understanding in the studied areas can be employed to develop better industrial processes not only on a large scale but also increasingly on a smaller scale. The small amounts of indium, gallium and germanium may favour smaller and more locally bound recovery.

Metalli-ionin ja hapon erotus toisistaan kalvosuodatuksella

Työn tarkoituksena oli kuparin ja hapon erottaminen toisistaan malliaineliuoksesta membraanitekniikalla. Kaivannaisteollisuudessa happoja käytetään metalleiden liuottamiseen. Lisäksi happamia jätevesiä syntyy sulfidikaivoksissa, sadeveden liuottaessa metalleja. Raskasmetallit ovat erittäin myrkyllistä vesieliöille. Työn tavoitteena oli saada happo ja metalli hyödynnettävään muotoon. Työn kokeellisessa osassa vertailtiin kahta polymeeristä ja keraamista membraania hapon ja metallin erotuksessa. Mittauksissa käytetyt membraanit olivat: AMS Technologies A-3012 ja A-3014 sekä Inopor ® Type SKR. Syöttöliuos sisälsi kuparisulfaattia ja rikkihappoa. Suodatukset tehtiin 30 ºC lämpötilassa useissa paineissa ja pH-arvoissa. Polymeeristen membraanien suodatusnäytteistä saadut retentiot kuparille olivat vastaavia aikaisempien tutkimusten tuloksien kanssa. A-3012 kalvon kuparin retentio oli 95 % ja A-3014 kalvolle kuparin retentio oli 90 %. Lisäksi mittausten korkeimmissa pH-arvoissa (2,9-2,3) happo konsentroitui permeaattiin. Polymeerisillä membraaneilla ei ollut merkkejä kalvon likaantumisesta tai hajoamisesta. Keraamisella membraanilla mitatut tulokset eivät olleet vastaavia aikaisempien tutkimusten tuloksien kanssa. Kuparin retentio olivat 2 ja 20 prosentin välillä, eikä liuoksen pH eronnut syötön ja permeaatin välillä. Tulosten perusteella molemmat tutkitut polymeeriset membraanit soveltuvat kuparin erottamiseen happamasta liuoksesta. Mittauksissa käytetty keraaminen membraani ei sovellu tähän tehtävään.

Mäntyöljyn tislauksen esikäsittely

Raakamäntyöljy on selluteollisuuden sivutuote. Suopa erotetaan mustalipeästä ja palstoitetaan tuottaen siten raakamäntyöljyä. Raakamäntyöljy tislataan tavanomaisesti viiteen pääjakeeseen: rasvahapot, hartsihapot, mäntyöljytisle, esiöljy ja mäntyöljypiki. Näiden jakeiden lisäksi raakamäntyöljyssä on erityisesti mustalipeästä siihen erottuneita epäpuhtauksia, jotka haittaavat raakamäntyöljyn prosessointia. Epäpuhtauksia ovat orgaaniset ja epäorgaaniset yhdisteet, kuten metallit, suolat ja ligniini. Nämä epäpuhtaudet aiheuttavat haitallisia reaktioita prosessissa huonontaen siten lopputuotejakeiden laatua. Tämän lisäksi epäpuhtaudet aiheuttavat saostumia prosessilaitteissa alentaen siten prosessointitehokkuutta. Raakamäntyöljyn esikäsittelyllä tehostetaan tislauksen toimintaa. Työssä esitetään esikäsittelymenetelmistä mm. degumming-menetelmä, laimea happopesu, hiilidioksidikäsittely, valkaisu ja lämpökäsittely. Menetelmien pohjalta valitaan tätä työtä varten yksi menetelmä, jonka pohjalta suunnitellaan kokeellisessa osassa suoritettavat kokeet. Kokeellinen osuus koostuu esikokeista, varsinaisista kokeista ja lisäkokeista. Menetelmän tarkoituksena on saavuttaa epäpuhtauksille 90–95 % reduktioaste. Kokeiden onnistumista tutkitaan analysoimalla alkuperäinen raakamäntyöljy, sekä jokaisen kokeen jälkeen erotetut faasit. Työssä saavutettiin hyvä erotustehokkuus. Alkuperäisen tavoitteen mukaista reduktioastetta ei pystytty määrittämään eri analyysimenetelmien ja niiden analyysituloksissa ilmenneiden eroavaisuuksien vuoksi, mutta lisäkokeiden ansiosta pystyttiin vahvistamaan kyseisen koejärjestelmän optimaalinen poistoaste. Lisäksi työssä havaittiin että esikäsittelytulos on hyvin riippuvainen käsiteltävän raaka-aineen koostumuksesta.

Lignoselluloosapohjaisten väkevähappohydrolysaattien kromatografinen fraktiointi

Väkevän hapon katalysoiman hydrolyysin avulla lignoselluloosasta on mahdollista valmistaa arvokkaita sokereita. Katalyyttinä toimiva happo voidaan käyttää uudelleen hydrolyysissä, jos se saadaan erotettua sokereista ilman neutralointia. Tämän kandidaatintyön tavoitteena oli selvittää, soveltuuko happoretardaatiotekniikka väkevähappohydrolysaatin fraktiointiin. Työssä verrattiin happoretardaatiotekniikkaa elektrolyyttiekskluusiotekniikkaan. Työn kirjallisuusosassa käsiteltiin happoretardaation ja elektrolyyttiekskluusion teoriaa. Lisäksi esiteltiin elektrolyyttiekskluusioon ja happoretardaatioon liittyviä tutkimuksia. Työn kokeellisessa osassa suoritettiin panoskromatografiakokeita käyttäen syöttöliuoksena rikkihappoa, etikkahappoa, glukoosia ja ksyloosia sisältävää synteettistä liuosta. Erotusmateriaaleina käytettiin neljää eri anionin- ja yhtä kationinvaihtohartsia. Kokeiden perusteella tutkittiin anioninvaihtohartsin tyypin ja kolonnin latauksen vaikutusta happoretardaatiotekniikalla saavutettavaan erotustulokseen sekä verrattiin elektrolyyttiekskluusiota happoretardaatioon. Työn tulosten perusteella rikkihappo laimeni happoretardaatiotekniikalla jopa 20-kertaisesti kromatografiakolonniin syötettyyn liuokseen verrattuna, riippumatta kolonnin latauksesta ja anioninvaihtohartsista. Rikkihapon laimenemisen vuoksi happoretardaatio ei soveltunut lignoselluloosapohjaisten väkevähappohydrolysaattien fraktiointiin. Elektrolyyttiekskluusiotekniikalla rikkihapon laimeneminen oli merkittävästi vähäisempää, minkä vuoksi elektrolyyttiekskluusion todettiin soveltuvan happoretardaatiota paremmin lignoselluloosapohjaisten väkevähappohydrolysaattien fraktiointiin.

Synthesis and spectral studies of methyl heterocylic systems

2-Carboxy-2?-methyldiphenyl sulfide was prepared by the Ullmann reaction and cyclodehydrated by sulfuric acid to afford 4-methylthioxanthone. 1-Methylthioxanthone was separated from the reaction mixture obtained upon cyclodehydration of 2-carboxy-3f-methyldiphenyl sulfide. In addition, 1-, 2-, 3- and 4-methylthioxanthone 10,10-dioxides were synthesized by oxidation of the corresponding thioxanthones. o-, m- and p-N-Tolylanthranilic acids were prepared by the Ullmann reaction and used as precursors for the preparation of 1-, 2- and 4- methyl-9-chloroacridine and finally 1-, 2-, 3- and 4-methylacridone. High resolution, 60 MHz PMR spectra were obtained on the four monomethyl isomers of xanthone, thioxanthone, thioxanthone 10,10-dioxide and acridone, and on 1-, 2- and 4-methyl-9-chloroacridine. For some compounds, coupling of all three different aromatic protons to the methyl was observed, two of the couplings typically being smaller than the third. With the large (ortho) coupling being on the order of 0.5 to 1.0 Hz, it was necessary to decouple the aromatic part of the spectrum. The magnitude of the ortho benzylic constant may be related to an incomplete Tr-bond delocalization in the molecules.

The nucleophillic substitution of various chloroanthraquinones of their possible rearrangement via aryne intermediates

The work in this thesis deals mainly with nucleophilic substitution of chloroanthraquinones as a route to various starting materials which might rearrange, via aryne intermediates to afford fused-ring heterocy1ic carboxylic acids. 1-Amino-5-chloroanthraquinone was successfully prepared by reacting 1,5-dichloroanthraquinone with sodium aZide in ref1uxing dimethylsulfoxide (DMSO). It could also be prepared from the same starting material by reaction with ammonia (gas) in DMSO in the presence of potassium fluoride. Treatment of l-amino-5-chloroanthraquinone with potassium amide in liquid ammonia or with potassium t-butoxide in t-butylbenzene returned mainly starting material, although in the latter case some 1-amino-5-hydroxyanthraquinone was also isolated. 1-Hydroxy-5-chloroanthraquinone was ultimately prepared by diazotization of the amino-analog. It was recovered almost quantitatively after treatmenu'with potassium amide in liquid ammonia. The reaction with potassium t-butoxide in t-buty1benzene was anomalous and gave 1-hydroxyanthraquinone as the only iso1able product. Acridines were successfully prepared by the action of 70% sulfuric acid on 1,5-bis(p-toluidino)-anthraquinone and 1-p-toluidino-5- ch10roanthraquinone, and in the latter case, cleavage to give an acridinecarboxylate was attempted. Substituted anthraquinones reacted with sodium azide in sulfuric acid to give azepindiones by -NH insertion. Methods for separating and identifying isomeric mixtures of these compounds were examined. Attempted decarbonylation of selected azepindiones to give acridones gave mainly what were thought to be amino-benzophenone derivatives. Chloroanthraquinones were found to react with hexamethylphosphoramide (HMPA) to give mixtures of the dimethylamino- and methylaminoderivatives. Under the same conditions halogeno-nitrobenzenes and nitrophenols were substituted to give the appropriate dimethyl aminobenzenes, except in two cases. 3-Chloronitrobenzene reacted anomalously to give a small amount of 3,3'-dichloroazobenzene and a trace of 4-dimethylamino-nitrobenzene. Pentachlorophenol reacted to give a pentachlorophenylphosphorodiamidate in good yield.