Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração

The thermodynamic performance of a refrigeration system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, and lubrication characteristics as well as the overall performance (based on the Second Law of Thermodynamics) of the refrigerating system using R134a or R600a as refrigerants. The study looked at the influences of variables: i) refrigerant charge (100, 110, 120 and 130 g), ii) rotational speed of the condenser blower (800 and 1100 RPM) and iii) nanoparticle concentration (0.1 and 0.5 g/l) on the system performance based on the Taguchi method in a matrix of L8 trials with the criterion "small irreversibility is better”. They were carried pulldown and cycling tests according to NBR 12866 and NBR 12869, respectively, to evaluate the operational parameters: on-time ratio, cycles per hour, suction and discharge pressures, oil sump temperature, evaporation and condensation temperatures, energy consumption at the set-point, total energy consumption and compressor power. In order to evaluate the nanolubricant characteristics, accelerated tests were performed in a HFRR bench. In each 60 minutes test with nanolubricants at a certain concentration (0, 0.1 and 0.5 g/l), with three replications, the sphere (diameter 6.00 ± 0.05 mm, Ra 0.05 ± 0.005 um, AISI 52100 steel, E = 210 GPa, HRC 62 ± 4) sliding on a flat plate (cast iron FC200, Ra <0.5 ± 0.005 um) in a reciprocating motion with amplitude of 1 mm, frequency 20 Hz and a normal load of 1,96 N. The friction coefficient signals were recorded by sensors coupled to the HFRR system. There was a trend commented bit in the literature: a nanolubricant viscosity reduction at the low nanoparticles concentrations. It was found the dominant trend in the literature: increased thermal conductivity with increasing nanoparticles mass fraction in the base fluid. Another fact observed is the significant thermal conductivity growth of nanolubricant with increasing temperature. The condenser fan rotational speed is the most influential parameter (46.192%) in the refrigerator performance, followed by R600a charge (38.606%). The Al2O3 nanoparticles concentration in the lubricant plays a minor influence on system performance, with 12.44%. The results of power consumption indicates that the nanoparticles addition in the lubricant (0.1 g/L), together with R600a, the refrigerator consumption is reduced of 22% with respect to R134a and POE lubricant. Only the Al2O3 nanoparticles addition in the lubricant results in a consumption reduction of about 5%.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Estudo teórico das propriedades eletrônicas e termodinâmicas de nanofitas quasiperiódicas BCN

Nanoscale materials composed of boron, nitrogen, and carbon have unique properties and may be useful in new technologies. In this thesis, we investigate some properties of BCN nanoribbons constructed according to the Fibonacci quasiperiodic sequence. We analyze properties such as structural stability, electronic density of states, electronic specific heat, band structure, and energy band gap. We have performed first-principles calculations based on density functional theory implemented in the SIESTA code. The results showed that nanoribbons present a fixed value of the formation energy. The electronic density of states was used to calculate the specific heat. We found an oscillatory behavior of the electronic specific heat, in the low temperature regime. We analyze the electronic band structure to determine the energy band gap. The energy band gap oscillates as a function of the Fibonacci generation index n. Our work suggest that appropriate choice of the building block materials of the quasiperiodic sequence, may lead to a tuneable band gap of the quasiperiodic nanoribbons.

Determinação do estado fundamental de compostos antiferromagnéticos da série Tb(1-x)Y(x)RhIn(5): aproximação teórico experimental

We present the results of electrical resistivity, magnetic susceptibility, specific heat and x-ray absorption spectroscopy measurements in Tb1−xYxRhIn5 (x = 0.00, 0.15, 0.4.0, 0.50 e 0.70) single crystals. Tb1−xYxRhIn5 is an antiferromagnetic AFM compound with ordering temperature TN ≈ 46 K, the higher TN within the RRhIn5 serie (R : rare earth). We evaluate the physical properties evolution and the supression of the AFM state considering doping and Crystalline Electric Field (CEF) effects on magnetic exchange interaction between Tb3+ magnetic ions. CEF acts like a perturbation potential, breaking the (2J + 1) multiplet s degeneracy. Also, we studied linear-polarization-dependent soft x-ray absorption at Tb M4 and M5 edges to validate X-ray Absorption Spectroscopy as a complementary technique in determining the rare earth CEF ground state. Samples were grown by the indium excess flux and the experimental data (magnetic susceptibility and specific heat) were adjusted with a mean field model that takes account magnetic exchange interaction between first neighbors and CEF effects. XAS experiments were carried on Total Electron Yield mode at Laborat´onio Nacional de Luz S´ıncrotron, Campinas. We measured X-ray absorption at Tb M4,5 edges with incident polarized X-ray beam parallel and perpendicular to c-axis (E || c e E ⊥ c). The mean field model simulates the mean behavior of the whole system and, due to many independent parameters, gives a non unique CEF scheme. XAS is site- and elemental- specific technique and gained the scientific community s attention as complementary technique in determining CEF ground state in rare earth based compounds. In this work we wil discuss the non conclusive results of XAS technique in TbRhIn5 compounds.

Phase diagram of the bosonic double-exchange model

The phase diagram of the simplest approximation to double-exchange systems, the bosonic double-exchange model with antiferromagnetic (AFM) superexchange coupling, is fully worked out by means of Monte Carlo simulations, large-N expansions, and variational mean-field calculations. We find a rich phase diagram, with no first-order phase transitions. The most surprising finding is the existence of a segmentlike ordered phase at low temperature for intermediate AFM coupling which cannot be detected in neutron-scattering experiments. This is signaled by a maximum (a cusp) in the specific heat. Below the phase transition, only short-range ordering would be found in neutron scattering. Researchers looking for a quantum critical point in manganites should be wary of this possibility. Finite-size scaling estimates of critical exponents are presented, although large scaling corrections are present in the reachable lattice sizes.

Efficient numerical methods for the random-field Ising model: Finite-size scaling, reweighting extrapolation, and computation of response functions

It was recently shown [Phys. Rev. Lett. 110, 227201 (2013)] that the critical behavior of the random-field Ising model in three dimensions is ruled by a single universality class. This conclusion was reached only after a proper taming of the large scaling corrections of the model by applying a combined approach of various techniques, coming from the zero-and positive-temperature toolboxes of statistical physics. In the present contribution we provide a detailed description of this combined scheme, explaining in detail the zero-temperature numerical scheme and developing the generalized fluctuation-dissipation formula that allowed us to compute connected and disconnected correlation functions of the model. We discuss the error evolution of our method and we illustrate the infinite limit-size extrapolation of several observables within phenomenological renormalization. We present an extension of the quotients method that allows us to obtain estimates of the critical exponent a of the specific heat of the model via the scaling of the bond energy and we discuss the self-averaging properties of the system and the algorithmic aspects of the maximum-flow algorithm used.

Weak coupling of acoustic-like phonons and magnon dynamics in incommensurate spin ladder compound Sr14Cu24O41

Intriguing lattice dynamics has been predicted for aperiodic crystals that contain incommensurate substructures. Here we report inelastic neutron scattering measurements of phonon and magnon dispersions in Sr14Cu24O41, which contains incommensurate one-dimensional (1D) chain and two-dimensional (2D) ladder substructures. Two distinct acoustic phonon-like modes, corresponding to the sliding motion of one sublattice against the other, are observed for atomic motions polarized along the incommensurate axis. In the long wavelength limit, it is found that the sliding mode shows a remarkably small energy gap of 1.7-1.9 meV, indicating very weak interactions between the two incommensurate sublattices. The measurements also reveal a gapped and steep linear magnon dispersion of the ladder sublattice. The high group velocity of this magnon branch and weak coupling with acoustic phonons can explain the large magnon thermal conductivity in Sr14Cu24O41 crystals. In addition, the magnon specific heat is determined from the measured total specific heat and phonon density of states, and exhibits a Schottky anomaly due to gapped magnon modes of the spin chains. These findings offer new insights into the phonon and magnon dynamics and thermal transport properties of incommensurate magnetic crystals that contain low-dimensional substructures.

Modelling and Verification of a Correction Factor to Evaluate the Efficiency of Solar Thermal Collectors with the Rapid Test Method

A new method for the evaluation of the efficiency of parabolic trough collectors, called Rapid Test Method, is investigated at the Solar Institut Jülich. The basic concept is to carry out measurements under stagnation conditions. This allows a fast and inexpensive process due to the fact that no working fluid is required. With this approach, the temperature reached by the inner wall of the receiver is assumed to be the stagnation temperature and hence the average temperature inside the collector. This leads to a systematic error which can be rectified through the introduction of a correction factor. A model of the collector is simulated with COMSOL Multipyisics to study the size of the correction factor depending on collector geometry and working conditions. The resulting values are compared with experimental data obtained at a test rig at the Solar Institut Jülich. These results do not match with the simulated ones. Consequentially, it was not pos-sible to verify the model. The reliability of both the model with COMSOL Multiphysics and of the measurements are analysed. The influence of the correction factor on the rapid test method is also studied, as well as the possibility of neglecting it by measuring the receiver’s inner wall temperature where it receives the least amount of solar rays. The last two chapters analyse the specific heat capacity as a function of pressure and tem-perature and present some considerations about the uncertainties on the efficiency curve obtained with the Rapid Test Method.

Análise energética em central fixa de produção de massas asfálticas

O consumo energético nas indústrias é algo que tem de ser monitorizado, avaliado e orientado, visando a eficiência energética e sustentabilidade, de modo não só a reduzir o consumo de combustíveis fósseis, mas também a auxiliar a redução da fatura económica. O presente trabalho teve como principal objetivo uma análise energética, e incorpora a caracterização térmica dos materiais utilizados na indústria de produção de massas asfálticas, e o desenvolvimento de um modelo térmico que preveja o comportamento dos mesmos, na produção de massas asfálticas, em central fixa com incorporação de material reciclado a frio. Primariamente o estudo passou pela análise dos consumos energéticos da instalação, caracterizando-a segundo o Decretolei 71/2008, de 15 de Abril, tendo-se constatado, que o consumo de gás natural se evidencia como uma das principais fontes de energia e um dos principais responsáveis pela emissão de GEE (Gases de Efeito de Estufa). Posteriormente o consumo de gás natural foi distribuído pelos pontos consumidores, o cilindro exsicador e a caldeira de aquecimento de óleo térmico. O cilindro exsicador é o principal consumidor energético, com um consumo próximo de 90% do gás natural total. Seguidamente foi realizada uma caracterização dos materiais utilizados na produção de massas asfálticas segundo o DSC (Differential Scanning Calorimetry). Os materiais analisados foram o reciclado/fresado, o calcário, o pó de calcário, o seixo, a areia e o granito. Os resultados dos materiais secos demonstraram que o material com maior cp (calor específico) foi a areia e o menor o calcário. Nos resultados dos materiais saturados observou-se que o seixo apresenta maior facilidade de remoção de humidade e o reciclado/fresado apresenta menor. Por último, foi realizado um modelo térmico com utilização de um balanço mássico e energético ao processo de secagem e sobreaquecimento dos agregados no cilindro exsicador. Conclui-se que as principais influências no consumo de gás natural, na produção de massas asfálticas com inclusão de material reciclado a frio, são: a necessidade energética de aquecimento em função da temperatura a obter, e a energia necessária para remover o conteúdo em humidade presente nos diversos materiais (fresado e agregados).

The effect of neutron irradiation on the density of low-energy excitations in vitreous silica

Systematic low-temperature measurements of the thermal conductivity, specific heat, dielectric constant, and temperature-dependent ultrasound velocity have been made on a single piece of vitreous silica. These measurements were repeated after fast neutron irradiation of the material. It was found that the irradiation produced changes of the same relative magnitude in the low-temperature excess specific heat C , the thermal conductivity K, ex and the anomalous temperature dependence of the ultrasound velocity Deltav/v. A corresponding change in the temperature dependent dielectric constant was not observed. It is therefore likely that K and Deltav/v are determined by the same localized excitations responsible for C , but the temperature dependence of the dielectric constant may have a different, though possibly related, origin. Furthermore, a consistent account for the measured C , K, ex and Deltav/v of unirradiated silica is given by the tunneling-state model with a single, energy-dependent density of states. Changes in these three properties due to irradiation can be explained by altering only the density of tunneling states incorporated in the model.

Evaluation of thermo-physical properties and drying kinetics of carrots in a convective hot air drying system

This paper presents an experimental study on the evolution of carrot properties along convective drying by hot air at different temperatures (50ºC, 60ºC and 70ºC). The thermo-physical properties calculated were: specific heat, thermal conductivity, diffusivity, enthalpy, heat and mass transfer coefficients. Furthermore, the data of drying kinetics were treated and adjusted according to the three empirical models: Page, Henderson & Pabis and Logarithmic. The sorption isotherms were also determined and fitted using the GAB model. The results showed that, generally, the thermo-physical properties presented a decline during the drying process, and the decrease was faster for the temperature of 70ºC. It was possible to verify that the Page model presented the best prediction ability for the representation of kinetics of the drying process. The GAB model used to fit the sorption isotherms showed a good prediction capacity and, at a given water activity, despite some variations, the amount of water sorbed increased with the decrease of drying temperature.

Variação da composição nutricional e propriedades de cenouras durante a secagem

Este trabalho teve como objetivo a determinação das propriedades da cenoura (Daucus carota L.), da variedade Nantes, antes, durante e após a secagem por convecção a três temperaturas diferentes (50, 60 e 70 ºC).De forma a verificar as alterações ao nível de diferentes propriedades, tais como: propriedades químicas (humidade, proteínas, fibras, cinzas, açúcares e 'aw') propriedades físicas (textura, cor, porosidade e densidade) e propriedades termofísicas (calor específico, condutividade térmica, difusividade e entalpia). Dos resultados obtidos foi possível concluir que a temperatura de secagem de 70 º C foi a que mais afetou as propriedades químicas analisadas, tais como a humidade, proteínas e açúcares redutores, onde estes sofreram uma diminuição ao longo das secagens. A 'aw' também apresentou uma diminuição ao longo das secagens, onde apresentou um menor valor na secagem a 70 ºC, tendo passado de 0,97 para 0,69, enquanto as temperaturas de 50 ºC e 60 ºC apresentaram um valor final igual, de 0,74. No que diz respeito às propriedades físicas, verificou-se que em relação à textura registaram-se evoluções semelhantes em termos de dureza, mastigabilidade e gomosidade, na medida em que sofreram uma acentuada diminuição nas primeiras horas de secagem, e a temperatura de 70 ºC foi a que mais afetou estas propriedades. No caso da cor a temperatura de 60 ºC foi a que provocou uma maior diferença de cor, a qual ao longo da secagem esta foi aumentando. A porosidade sofreu um aumento com as secagens devido à diminuição da humidade, no entanto a temperatura de 70 ºC foi a que obteve uma menor porosidade, e as temperaturas de 50 ºC e 60 ºC apresentaram valores de porosidade semelhantes. As propriedades termofísicas registaram uma diminuição ao longo da secagem, onde o calor específico sofreu uma maior diminuição com a temperatura de 70 ºC, passando de 3,90 kJ/kg.K para 1,99 kJ/kg.K. A condutividade térmica também sofreu uma maior diminuição com a temperatura de 70 ºC, diminuindo de 0,5243 W/m.K para 0,2782 W/m.K. A difusividade foi de igual forma afetada pela temperatura de 70 ºC, tendo diminuído de 1,50×10-7 m2/s para 1,06×10-7 m2/s. No caso da entalpia, esta sofreu uma maior diminuição com a temperatura de 50 ºC, passando de 233 J/kg para 96,7 J/kg. As isotérmicas de sorção foram ajustadas ao modelo de GAB, onde se verificou que apesar de algumas oscilações a quantidade de água sorvida a uma determinada aw, aumentou com a diminuição da temperatura.Os dados da cinética de secagem foram tratados e ajustados de acordo com três modelos: Page, Henderson & Pabis e Logarítmico, tendo-se verificado que o modelo de Page foi o que mostrou melhor descrever os processos em estudo, enquanto o pior modelo para descrever a cinética de secagem foi o Logarítmico.

Estudo de modelos simplificados com interações de longo alcance no ensemble microcanônico

Tese (doutorado)Universidade de Brasília, Instituto de Física, Programa de Pós-Graduação em Física, 2015.

Production and characterization of novel thermoplastic (nano)composite materials for additive manufacturing applications

The increasing environmental global regulations have directed scientific research towards more sustainable materials, even in the field of composite materials for additive manufacturing. In this context, the presented research is devoted to the development of thermoplastic composites for FDM application with a low environmental impact, focusing on the possibility to use wastes from different industrial processes as filler for the production of composite filaments for FDM 3D printing. In particular carbon fibers recycled by pyro-gasification process of CFRP scraps were used as reinforcing agent for PLA, a biobased polymeric matrix. Since the high value of CFs, the ability to re-use recycled CFs, replacing virgin ones, seems to be a promising option in terms of sustainability and circular economy. Moreover, wastes from different agricultural industries, i.e. wheat and rice production processes, were valorised and used as biofillers for the production of PLA-biocomposites. The integration of these agricultural wastes into PLA bioplastic allowed to obtain biocomposites with improved eco-sustainability, biodegradability, lightweight, and lower cost. Finally, the study of novel composites for FDM was extended towards elastomeric nanocomposite materials, in particular TPU reinforced with graphene. The research procedure of all projects involves the optimization of production methods of composite filaments with a particular attention on the possible degradation of polymeric matrices. Then, main thermal properties of 3D printed object are evaluated by TGA, DSC characterization. Additionally, specific heat capacity (CP) and Coefficient of Linear Thermal Expansion (CLTE) measurements are useful to estimate the attitude of composites for the prevention of typical FDM issues, i.e. shrinkage and warping. Finally, the mechanical properties of 3D printed composites and their anisotropy are investigated by tensile test using distinct kinds of specimens with different printing angles with respect to the testing direction.