Clean development mechanism and joint implementation in China and Russia as related to industrial energy projects

Being highly discussed the problem of climate change and global warming has been keeping importance for several of decades. As a response to the world’s need in solution for climate change disasters, the United Nations Framework Convention on Climate Change was adopted in 1992 and supplemented with the Kyoto protocol in 1997. This work is aimed to give better understanding of the Convention, Kyoto Protocol with its mechanisms and their function, related to energy projects in such case countries, as Russia and China, in order to assist evaluation of projects cost-effectiveness. It provides basic information about the Convention and the Protocol with their regulations, overview of present situation and future post-Kyoto forecasts, while the most attention is concentrated on the clean development mechanism and joint implementation step-by-step project cycles and specific regulations in given countries. The current study disclosed that CDM and JI project cycles are resulting in a complicated process. By the moment it requires step-by-step following of a number of methodologies, spending time and finance to particular project development. Uncertainties about post-Kyoto period bring additional risk to the projects and complicate any business decision concerning Kyoto Protocol.

Energy efficiency parameters in variable speed drives

The main purpose of this thesis is to measure and evaluate how accurately the current energy saving calculation in ABB’s new variable speed drive ACS850 works. The main topic of this thesis is energy-efficiency parameters. At the beginning of this thesis centrifugal pump, squirrel cage motor and variable speed drive, including some equations related to them, are being introduced. Also methods of throttling control and variable speed drive control of centrifugal pumps are being introduced. These subjects are introduced because the energy saving calculation in ACS850 is related to the centrifugal pumps usually driven by squirrel cage motors. The theory also includes short section about specific energy of pumping. Before measurements the current energy saving calculation of ACS850 is being introduced and analyzed. The measurements part includes introduction of measuring equipment, measurement results, summary and analysis of the measurements. At the end of this thesis a proposal for an improvement to the current energy saving calculation is being introduced and few proposals are made for new energy-efficiency parameters, which could be added to variable speed drives. At the end are also thoughts

Utilisation of biomass for energy production in the North-West Russian forest industry

Traditionally, fossil fuels have always been the major sources of the modern energy production. However prices on these energy sources have been constantly increasing. The utilization of local biomass resources for energy production can substitute significant part of the required energy demand in different energy sectors. The introduction of the biomass usage can easily be started in the forest industry first as it possesses biomass in a large volume. The forest industry energy sector has the highest potential for the fast bioenergy development in the North-West Russia. Therefore, the question concerning rational and effective forest resources use is important today as well as the utilization of the forestry by-products. This work describes and analyzes the opportunities of utilising biomass, mainly, in the form of the wood by-products, for energy production processes in general, as well as for the northwest Russian forest industry conditions. The study also covers basic forest industry processes and technologies, so, the reader can get familiar with the information about the specific character of the biomass utilization. The work gives a comprehensive view on the northwest forest industry situation from the biomass utilisation point of view. By presenting existing large-scale sawmills and pulp and paper mills the work provides information for the evaluation of the future development of CHP investments in the northwest Russian forest industry.

Sustainable Waste-to-Energy Production: Performance Evaluation of Distributed Generation fuelled by Landfill Gas

The environmental impact of landfill is a growing concern in waste management practices. Thus, assessing the effectiveness of the solutions implemented to alter the issue is of importance. The objectives of the study were to provide an insight of landfill advantages, and to consolidate landfill gas importance among others alternative fuels. Finally, a case study examining the performances of energy production from a land disposal at Ylivieska was carried out to ascertain the viability of waste to energy project. Both qualitative and quantitative methods were applied. The study was conducted in two parts; the first was the review of literatures focused on landfill gas developments. Specific considerations were the conception of mechanism governing the variability of gas production and the investigation of mathematical models often used in landfill gas modeling. Furthermore, the analysis of two main distributed generation technologies used to generate energy from landfill was carried out. The review of literature revealed a high influence of waste segregation and high level of moisture content for waste stabilization process. It was found that the enhancement in accuracy for forecasting gas rate generation can be done with both mathematical modeling and field test measurements. The result of the case study mainly indicated the close dependence of the power output with the landfill gas quality and the fuel inlet pressure.

Isolation of compounds attractive to the leaf-cutting ant Atta sexdens rubropilosa forel (hymenoptera: Formicidae) from Mabea fistulifera elaiosome

Mabea fistulifera (Euphorbiaceae)is a pioneer plant species with seeds dispersed by the ant Atta sexdens rubropilosa. Since the ants are attracted to the seeds to use its elaiosome as a source of energy, we investigated its composition. The elaiosomes from 13,000 seeds were extracted with a methanol:chloroform mixture (2:1 v/v) and yielded 22% of a residue. This residue was fractionated by column chromatography and its composition determined by infrared spectroscopy and chromatography/mass spectrometry (GC-MS). The elaiosome lipids are constituted mainly by free fatty acids, triacylglycerols and minor quantities of monoacylglycerols or diacylglycerols.

Environmental policy instruments concerning industrial end-use energy efficiency

Energy efficiency and saving energy are the main question marks when thinking of reducing carbon dioxide emissions or cutting costs. The objective of thesis is to evaluate policy instruments concerning end-use energy efficiency of heavy industry in European Union. These policy instruments may be divided in various ways, but in this thesis the division is to administrative, financial, informative and voluntary instruments. Administrative instruments introduced in this thesis are Directive on Integrated Pollution Prevention and Control, Directive on Energy End-use Efficiency and Energy Services, and Climate and Energy Package. Financial means include energy and emission taxation, EU Emission Trading Scheme and diverse support systems. Informative instruments consist of horizontal BAT Reference Document for Energy Efficiency, as well as substantial EU documents including Green Paper on Energy Efficiency, Action Plan for Energy Efficiency and An Energy Policy for Europe. And finally, voluntary instruments include environmental managements systems like ISO 14001 and EMAS, energy auditing and benchmarking. The efficiency of different policy instruments vary quite a lot. Informative instruments lack the commitment from industry and are thus almost ineffective, contrary to EU Emission Trading Scheme, which is said to be the solution to climate problems. The efficiency of administrative means can be placed between those mentioned and voluntary instruments are still quite fresh to be examined fruitfully. However, each instrument has their potential and challenges. Cases from corporate world strengthen the results from theoretical part. Cases were written mainly on the basis of interviews. The interviewees praised the energy efficiency contract of Finnish industry, but the EU ETS takes the leading role of policy instruments. However, for industry the reductions do not come easily.

A model for specific interactions of manganese-phthalocyanine in protic media

Extinction coefficients (e) changes of manganese phthalocyanine (Mn-Pc) were studied in different organic solvents and related to solvent polarity scales; (Kosower's values (Z), Dimroth's values (E T), donor numbers (DN) and linear solvation energy relationships (LSER) or linear free energy relationships (LFER));, theoretical molecular orbital calculations and ligand/solvent coordination processes in order to predict molecular interaction with the medium and identification of predominant intermolecular forces.

Perspectives for the production and usage of wood chips as a source of energy in the North-West of Russia

The development of bioenergy on the basis of wood fuels has received considerable attention in the last decades. The combination of large forest resources and reliance on fossil fuels makes the issue of wood chips usage in Russia an actual topic for the analysis. The main objective of this study is to disclose the current state and perspectives for the production of wood chips and their usage as a source of energy in the North-West of Russia. The study utilizes an integrated approach to explore the market of wood chips on the basis of comprehensive analysis of documentation and expert opinions. The analysis of wood chips market was performed for eight regions of the North-West district of Russia within two major dimensions: its current state and perspectives in the nearest five years. The results of the study show a comprehensive picture of the wood chips market, including the potential for wood chips production, the specific features of production and consumption and the perspectives for the market development within the regions of the North-West district of Russia. The study demonstrated that the market of wood chips is underdeveloped in the North-West of Russia. The findings of the work may be used by forest companies for the strategic planning.

The effects of location, feedstock availability, and supply-chain logistics on the greenhouse gas emissions of forest-biomass energy utilization in Finland

Forest biomass represents a geographically distributed feedstock, and geographical location affects the greenhouse gas (GHG) performance of a given forest-bioenergy system in several ways. For example, biomass availability, forest operations, transportation possibilities and the distances involved, biomass end-use possibilities, fossil reference systems, and forest carbon balances all depend to some extent on location. The overall objective of this thesis was to assess the GHG emissions derived from supply and energy-utilization chains of forest biomass in Finland, with a specific focus on the effect of location in relation to forest biomass’s availability and the transportation possibilities. Biomass availability and transportation-network assessments were conducted through utilization of geographical information system methods, and the GHG emissions were assessed by means of lifecycle assessment. The thesis is based on four papers in which forest biomass supply on industrial scale was assessed. The feedstocks assessed in this thesis include harvesting residues, smalldiameter energy wood and stumps. The principal implication of the findings in this thesis is that in Finland, the location and availability of biomass in the proximity of a given energyutilization or energy-conversion plant is not a decisive factor in supply-chain GHG emissions or the possible GHG savings to be achieved with forest-biomass energy use. Therefore, for the greatest GHG reductions with limited forest-biomass resources, energy utilization of forest biomass in Finland should be directed to the locations where most GHG savings are achieved through replacement of fossil fuels. Furthermore, one should prioritize the types of forest biomass with the lowest direct supply-chain GHG emissions (e.g., from transport and comminution) and the lowest indirect ones (in particular, soil carbon-stock losses), regardless of location. In this respect, the best combination is to use harvesting residues in combined heat and power production, replacing peat or coal.

Commercialization of Modern Renewable Energy

The threat of global warming and its consequences are widely recognized, and the question of how to proceed with the long transition towards fossil fuel -neutral economies concerns many nations and people. At the same time the world’s primary energy use is predicted to increase significantly during the next decades as a result of global population and welfare increase. Improved energy efficiency and increased use of renewable energy sources in the world’s energy mix play important roles in the future energy production and consumption. The objective of this thesis is to study how novel renewable energy technologies, such as distributed small-scale bio-fueled combined heat and power production and wind power technologies could be commercialized efficiently. A wide array of attributes may contribute to the diffusion of new products. In general, the bioenergy and wind power technologies are in emerging phases, and the diffusion stage varies from country to country. The effects of firms’ technology choices, collaboration and alliances are studied in this thesis. Furthermore, the roles of national energy infrastructure and energy support schemes in the commercialization of new renewable energy products are explored. The empirical data is based on energy expert interviews, financial and patent data, and literature reviews of different case studies. The thesis comprises two parts. The first part provides an overview of the study, and the second part includes six research publications. The results reveal that small-scale bio-fueled combined heat and power production and wind power technologies are still in emerging phases in their life cycles, and energy support schemes are crucial in the market diffusion. The study contributes to earlier findings in the literature and industry by confirming that adequate energy policies and energy infrastructure are fundamental in the commercialization of novel renewable energy technologies. Firm-specific issues, including business relationships and new business models, and market-related issues will have a more significant role in the market penetration in the future, when the technologies mature and become competitive without political support schemes.

Energy saving potential in reservoir pumping

Pumping systems account for up to 22 % of the energy consumed by electrical motors in European industry. Many studies have shown that there is also a lot of potential for energy savings in these systems with the improvement of devices, flow control or surrounding sys-tem. The best method for more energy efficient pumping has to be found for each system separately. This thesis studies how energy saving potential in reservoir pumping system is affected by surrounding variables, such as the static head variation and friction factor. The objective is to create generally applicable graphs to quickly compare methods for reducing pumping system’s energy costs. The gained results are several graphs showcasing how the chosen variables affect energy saving potential of the pumping system in one specific case. To judge if these graphs are generally applicable, more testing with different pumps and environments are required.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Fundraising and investor relations in social enterprise: Marketing your way out of the pioneer gap in African off-grid renewable energy

Social enterprises apply the best of business for the pursuit of social or environmental mission while also generating revenues. Globally, nearly 1,3 billion people lack access to electricity, as well as another billion having access to only low quality and infrequent electricity. Off-grid renewable energy, like solar, will increasingly have a key role in the solution of the energy access issue. The pioneer gap in off-grid renewable energy consists of financing (or funding) gaps and capacity gaps, to do with both the early stage of the enterprises in question, as well as the early stage of the whole industry. The gaps are emphasised by specific characteristics of off-grid renewable energy business models and the requirements of operating in bottom-of-the-pyramid markets. The marketing perspective to fundraising is chosen to uncover the possible role enterprises themselves have in bridging the pioneer gap. The purpose of this thesis is to study how social enterprises operating in off-grid renewable energy in Africa utilise marketing activities in their investor relations in bridging the pioneer gap. This main research question is divided into the following sub-questions:  How does the pioneer gap affect fundraising for these enterprises?  How are the funding needs for these enterprises characterised?  How do these enterprises build trust in their investor relations? The theoretic framework is built on relationship marketing and investor relations, with an emphasis on creation of trust. The research is conducted as a thematical case study. Primary data is gathered via semi-structured interviews with six solar energy companies and two accelerators. According to the findings, the main components affecting trust-creation are diminished information asymmetry and perceived risk, mission alignment as well as a personal fit or relationship with the investor. Therefore, an enterprise can utilise e.g. the following marketing activities in their investor relations to bridge the pioneer gap: ensuring investor material, the enterprise story and presenting of them is clear, concise and complete to “package” the enterprise as an investment; taking investor needs and motivations into account as well as utilising existing investors as ambassadors.

Apply of energy storages in electricity distribution networks and reserve capacity applications

The Thesis is dedicated to development of an operative tool to support decision making of battery energy storages implementation in distribution networks. The basics of various battery technologies, their perspectives and challenges are represented in the Thesis. Mathematical equations that describe economic effect from battery energy storage installation are offered. The main factors that influence profitability of battery settings have been explored and mathematically defined. Mathematical model and principal trends of battery storage profitability under an impact of the major factors are determined. The meaning of annual net value was introduced to show the difference between savings and required costs. The model gives a clear vision for dependencies between annual net value and main factors. Proposals for optimal network and battery characteristics are suggested.

Protein-energy malnutrition halts hemopoietic progenitor cells in the G0/G1 cell cycle stage, thereby altering cell production rates

Protein energy malnutrition (PEM) is a syndrome that often results in immunodeficiency coupled with pancytopenia. Hemopoietic tissue requires a high nutrient supply and the proliferation, differentiation and maturation of cells occur in a constant and balanced manner, sensitive to the demands of specific cell lineages and dependent on the stem cell population. In the present study, we evaluated the effect of PEM on some aspects of hemopoiesis, analyzing the cell cycle of bone marrow cells and the percentage of progenitor cells in the bone marrow. Two-month-old male Swiss mice (N = 7-9 per group) were submitted to PEM with a low-protein diet (4%) or were fed a control diet (20% protein) ad libitum. When the experimental group had lost about 20% of their original body weight after 14 days, we collected blood and bone marrow cells to determine the percentage of progenitor cells and the number of cells in each phase of the cell cycle. Animals of both groups were stimulated with 5-fluorouracil. Blood analysis, bone marrow cell composition and cell cycle evaluation was performed after 10 days. Malnourished animals presented anemia, reticulocytopenia and leukopenia. Their bone marrow was hypocellular and depleted of progenitor cells. Malnourished animals also presented more cells than normal in phases G0 and G1 of the cell cycle. Thus, we conclude that PEM leads to the depletion of progenitor hemopoietic populations and changes in cellular development. We suggest that these changes are some of the primary causes of pancytopenia in cases of PEM.