High-performance liquid chromatography of the renal blood flow marker p-aminohippuric acid (PAH) and its metabolite N-acetyl PAH improves PAH clearance measurements.

PAH (N-(4-aminobenzoyl)glycin) clearance measurements have been used for 50 years in clinical research for the determination of renal plasma flow. The quantitation of PAH in plasma or urine is generally performed by colorimetric method after diazotation reaction but the measurements must be corrected for the unspecific residual response observed in blank plasma. We have developed a HPLC method to specifically determine PAH and its metabolite NAc-PAH using a gradient elution ion-pair reversed-phase chromatography with UV detection at 273 and 265 nm, respectively. The separations were performed at room temperature on a ChromCart (125 mmx4 mm I.D.) Nucleosil 100-5 microm C18AB cartridge column, using a gradient elution of MeOH-buffer pH 3.9 1:99-->15:85 over 15 min. The pH 3.9 buffered aqueous solution consisted in a mixture of 375 ml sodium citrate-citric acid solution (21.01 g citric acid and 8.0 g NaOH per liter), added up with 2.7 ml H3PO4 85%, 1.0 g of sodium heptanesulfonate and completed ad 1000 ml with ultrapure water. The N-acetyltransferase activity does not seem to notably affect PAH clearances, although NAc-PAH represents 10.2+/-2.7% of PAH excreted unchanged in 12 healthy subjects. The performance of the HPLC and the colorimetric method have been compared using urine and plasma samples collected from healthy volunteers. Good correlations (r=0.94 and 0.97, for plasma and urine, respectively) are found between the results obtained with both techniques. However, the colorimetric method gives higher concentrations of PAH in urine and lower concentrations in plasma than those determined by HPLC. Hence, both renal (ClR) and systemic (Cls) clearances are systematically higher (35.1 and 17.8%, respectively) with the colorimetric method. The fraction of PAH excreted by the kidney ClR/ClS calculated from HPLC data (n=143) is, as expected, always <1 (mean=0.73+/-0.11), whereas the colorimetric method gives a mean extraction ratio of 0.87+/-0.13 implying some unphysiological values (>1). In conclusion, HPLC not only enables the simultaneous quantitation of PAH and NAc-PAH, but may also provide more accurate and precise PAH clearance measurements.

Influence of stationary phase and eluent properties on chromatographic separation of carbohydrates

In this thesis, the sorption and elastic properties of the cation-exchange resins were studied to explain the liquid chromatographic separation of carbohydrates. Na+, Ca2+ and La3+ form strong poly(styrene-co-divinylbenzene) (SCE) as well as Na+ and Ca2+ form weak acrylic (WCE) cation-exchange resins at different cross-link densities were treated within this work. The focus was on the effects of water-alcohol mixtures, mostly aqueous ethanol, and that of the carbohydrates. The carbohydrates examined were rhamnose, xylose, glucose, fructose, arabinose, sucrose, xylitol and sorbitol. In addition to linear chromatographic conditions, non-linear conditions more typical for industrial applications were studied. Both experimental and modeling aspectswere covered. The aqueous alcohol sorption on the cation-exchangers were experimentally determined and theoretically calculated. The sorption model includes elastic parameters, which were obtained from sorption data combined with elasticity measurements. As hydrophilic materials cation-exchangers are water selective and shrink when an organic solvent is added. At a certain deswelling degree the elastic resins go through glass transition and become as glass-like material. Theincreasing cross-link level and the valence of the counterion decrease the sorption of solvent components in the water-rich solutions. The cross-linkage or thecounterions have less effect on the water selectivity than the resin type or the used alcohol. The amount of water sorbed is higher in the WCE resin and, moreover, the WCE resin is more water selective than the corresponding SCE resin. Theincreased aliphatic part of lower alcohols tend to increase the water selectivity, i.e. the resins are more water selective in 2-propanol than in ethanol solutions. Both the sorption behavior of carbohydrates and the sorption differences between carbohydrates are considerably affected by the eluent composition and theresin characteristics. The carbohydrate sorption was experimentally examined and modeled. In all cases, sorption and moreover the separation of carbohydrates are dominated by three phenomena: partition, ligand exchange and size exclusion. The sorption of hydrophilic carbohydrates increases when alcohol is added into the eluent or when carbohydrate is able to form coordination complexes with the counterions, especially with multivalent counterions. Decreasing polarity of the eluent enhances the complex stability. Size exclusion effect is more prominent when the resin becomes tighter or carbohydrate size increases. On the other hand,the elution volumes between different sized carbohydrates decreases with the decreasing polarity of the eluent. The chromatographic separation of carbohydrateswas modeled, using rhamnose and xylose as target molecules. The thermodynamic sorption model was successfully implemented in the rate-based column model. The experimental chromatographic data were fitted by using only one adjustable parameter. In addition to the fitted data also simulated data were generated and utilized in explaining the effect of the eluent composition and of the resin characteristics on the carbohydrate separation.

Koboltin ja nikkelin poisto sinkkisulfaattiliuoksesta ioninvaihdolla

Työssä tutkittiin kahden silikapohjaisen erotusmateriaalin soveltuvuutta nikkelin ja koboltin poistoon sinkkisulfaattiliuoksista. Suurin osa kokeista tehtiin ioninvaihtimella, jonka funktionaalinen ryhmä on iminodietikkahappo. Vertailuerotusmateriaalin toiminta perustui adsorptioon. Liuoksina käytettiin sekä autenttista prosessiliuosta että synteettistä ZnSO4-liousta. Ioninvaihtimen kestävyyskokeissa selvisi, että tutkittu ioninvaihdin kestää hyvin sekä 60 oC lämpötilan että happamia olosuhteita. Emäksisissä liuoksissa silikarunko ei kestä. Jo 0,1 M NaOH-liuos liuottaa merkittävästi hartsia vuorokauden aikana. Vaihtimen vetyionikapasiteetiksi saatiin titrauksella 2,3 mekv/g. Tasapainokokeilla saatiin selville, että ioninvaihdin on selektiivinen nikkelille sinkin suhteen ja että selektiivisyys kasvaa liuoksen pH:n laskiessa. Koboltille ioninvaihdin ei ole selektiivinen sinkin suhteen. Mikäli sinkin pitoisuus on tuhansia kertoja nikkelin pitoisuutta suurempi, ei ioninvaihtimen Ni-selektiivisyys riitä myöskään nikkelille. Synteettisillä ZnSO4-liuoksilla tehtyjen kolonnikokeiden perusteella havaittiin, että tutkitulla ioninvaihtimella voidaan laimeista ZnSO4-liuoksista poistaa nikkeliä selektiivisesti. Nikkelin eluointi onnistui helposti 1 M H2SO4:lla. Vertailukokeen perusteella oli ioninvaihtimen Ni/Zn-selektiivisyys referenssiadsorbentin Ni/Zn-selektiivisyyttä pienempi. Ioninvaihtokolonnin mallintaminen ei onnistunut riittävän hyvin kuvaamaan ioninvaihtimessa tapahtuvaa samanaikaista ioninvaihtoa ja adsorptiota. Sen sijaan kun kolonnissa oli vertailumateriaalina käytetty adsorbentti, saatiin kolonnikokeiden tulokset mallilla hyvin ennustettua.

Epäpuhtauksien poistaminen sinkkisulfaattiliuoksista käyttäen selektiivisiä ioninvaihtimia

Diplomityössä on tutkittu kuparin, koboltin, nikkelin ja kadmiumin poistamista sinkkisulfaattiliuoksista käyttäen uusia silikarunkoisia kelatoivia erotusmateriaaleja. Vertailukohteena on käytetty perinteisiä kaupallisia polymeerirunkoisia kelatoivia ioninvaihtohartseja. Laboratoriokokeissa selvitettiin erotusmateriaalien adsorptio- ja ioninvaihto-ominaisuuksia tasapaino- ja kolonnikokeilla. Silikarunkoisten erotusmateriaalien kemiallista kestävyyttä tutkittiin olosuhteissa, jotka vastaavat prosessisyklin eri vaiheita. Metallien adsorptiomekanismien selvittämiseksi erotusmateriaaleille tehtiin happo-emäs ja sulfaattititraukset. Tasapainokokeet osoittivat, että silikarunkoisilla erotusmateriaaleilla saatiin kupari erotettua väkevistä sinkkisulfaattiliuoksista polymeerirunkoisia kelatoivia ioninvaihtohartseja paremmin. Tutkituilla erotusmateriaaleilla ja ioninvaihtohartseilla ei havaittu merkittävää selektiivisyyttä koboltille, nikkelille tai kadmiumille sinkin ja kuparin läsnä ollessa. Kolonnikokeilla yritettiin löytää paras esikäsittely-lataus-eluointisykli kuparin talteenottoon väkevistä sinkkisulfaattiliuoksista silikarunkoisilla erotusmateriaaleilla. Kolonnikokeissa esikäsittely tehtiin laimealla NaOH:lla, jonka jälkeen petiin syötettiin hapanta sinkkisulfaattiliuosta. Eluointi onnistui hyvin laimealla rikkihapolla. Kolonnikokeiden tulokset osoittivat, että kupari on mahdollista erottaa väkevistä sinkkisulfaattiliuoksista. Silikarunkoisten erotusmateriaalien kemiallista kestävyyttä tutkittaessa havaittiin materiaalien kestävän hyvin happoja ja 60 oC:en lämpötilaa. Sitä vastoin alkaalisissa olosuhteissa tapahtui silikan liukenemista. Tutkituilla erotusmateriaaleilla havaittiin kuparin sitoutumista sekä ioninvaihtomekanismin avulla että sitoutuneena neutraalina suolana.

Marjojen flavonoidien uuttaminen

Flavonoidit ovat kasvien polyfenolisia sekundäärimetaboliitteja, jotka koostuvat 15-hiilisestä C6-C3-C6-perusrungosta. Niillä on havaittu useita terveyden kannalta edullisia ominaisuuksia kuten antioksidatiivisia, antikarsinogeenisia, antiallergeenisia, anti-inflammatorisia, estrogeenisia sekä antimikrobiaalisia vaikutuksia. Kasvimateriaalia käyttävän elintarviketeollisuuden sivuvirrat ovat flavonoidi-pitoisten jakeiden arvokkaita raaka-aineita. Tässä työssä tarkoituksena oli tutkia marjojen puristusjäännöksen sisältämien flavonoidien uuttamista ja uuttautumiseen vaikuttavia tekijöitä kuten liuottimen koostumusta ja määrää, uuttolämpötilaa ja -aikaa sekä liuottimen lisäaineita. Uutteet analysointiin HPLC:lla käyttäen ODS-2-kolonnia ja gradienttieluointia. Komponentit detektoitiin niille tyypillisillä UV-VIS-aallonpituuksilla ja identifioitiin vertaamalla flavonoidiprofiililtaan tunnettujen marjojen kromatogrammeihin. Antosyaanien kvantitatiiviseen analysointiin käytettiin spektrofotometrista pH-eromenetelmää ja tulokset ilmoitettiin syanidiini-3-glukosidina. Uutteiden kestävyyttä tutkittiin säilyttämällä näytteitä eri olosuhteissa sekä lisäämällä niihin uuton saantoon ja komponenttien säilyvyyteen vaikuttavia aineita. Useimmat tutkituista hapoista paransivat flavonoidien saantoa ja uutteiden säilyvyyttä, mutta esim. askorbiinihapon lisääminen nopeutti tiettyjen uutteen sisältämien flavonoidien tuhoutumista.

Glyoxysomal malate-dehydrogenase and malate synthase from Soybean cotyledons (Glycine max. L.): Enzyme association, antibody-production and cDNA cloning

In order to investigate a possible association between soybean malate synthase (MS; L-malate glyoxylate-lyase, CoA-acetylating, EC 4.1.3.2) and glyoxysomal malate dehydrogenase (gMDH; (S)-malate: NAD(+) oxidoreductase, EC 1.1.1.37), two consecutive enzymes in the glyoxylate cycle, their elution profiles were analyzed on Superdex 200 HR fast protein liquid chromatography columns equilibrated in low- and high-ionic-strength buffers. Starting with soluble proteins extracted from the cotyledons of 5-d-old soybean seedlings and a 45% ammonium sulfate precipitation, MS and gMDH coeluted on Superdex 200 HR (low-ionic-strength buffer) as a complex with an approximate relative molecular mass (M(r)) of 670000. Dissociation was achieved in the presence of 50 mM KCl and 5 mM MgCl2, with the elution of MS as an octamer of M, 510 000 and of gMDH as a dimer of M, 73 000. Polyclonal antibodies raised to the native copurified enzymes recognized both denatured MS and gMDH on immunoblots, and their native forms after gel filtration. When these antibodies were used to screen a lambda ZAP II expression library containing cDNA from 3-d-old soybean cotyledons, they identified seven clones encoding gMDH, whereas ten clones encoding MS were identified using an antibody to SDS-PAGE-purified MS. Of these cDNA clones a 1.8 kb clone for MS and a 1.3-kb clone for gMDH were fully sequenced. While 88% identity was found between mature soybean gMDH and watermelon gMDH, the N-terminal transit peptides showed only 37% identity. Despite this low identity, the soybean gMDH transit peptide conserves the consensus R(X(6))HL motif also found in plant and mammalian thiolases.

Germaniumin talteenotto ioninvaihtohartseilla

Työssä tutkittiin laboratorio-olosuhteissa germaniumin talteenottoa happamista hydrometallurgisista sulfaattiliuoksista käyttäen kaupallisia ioninvaihtohartseja. Germaniumin talteenottoa tutkittiin sekä tasapaino- että kolonnikokein syöttöliuoksista joiden pH oli alueella 0,8–3,0. Tutkituista hartseista parhaiten germanium voitiin erottaa käyttäen emäsmuotoista N-metyyli-D-glukamiini-tyyppistä ioninvaihtohartsia (esim. Rohm & Haasin IRA-743). Germaniumille määritettiin adsorptioisotermit tasapainokokein sekä emäs- että happomuotoisilla hartseilla. Adsorptioisotermien perusteella parhaiten germa-niumia adsorboi emäsmuotoinen IRA-743-hartsi kun liuoksen alku-pH oli tutkitun alueen korkein. Lämpötilassa 25 °C kapasiteetti oli 114 mg Ge/g. Tasapainokokein määritettiin emäsmuotoisilla hartseilla germaniumin lisäksi myös kuparia ja kobolttia sisältävillä liuoksilla Ge:n jakaantumisvakiot sekä erotustekijät Ge/Cu ja Ge/Co. Havaittiin, että IRA-743:lla alku-pH:ssa 3,0 Ge:n jakaantumisvakiot sekä erotustekijät Ge/Cu ja Ge/Co olivat selvästi suuremmat kuin muilla tutkituilla hartseilla. Arseenin, nikkelin, sinkin ja rauta(III):n adsorboitumista emäsmuotoiseen IRA-743:een tutkittiin monimetallisella liuoksella syöttöliuoksen pH:n ollessa alueella 1,4–3,6. Kokeissa havaittiin, että hartsi adsorboi hieman Ni:a ja Zn:a tasapaino-pH:n ollessa yli 5,5. Arseenia ei tutkitulla pH-alueella havaittu adsorboituvan. Lisäksi huomattiin, että rauta alkaa saostua pH:n ollessa hieman alle kolme. Kolonnikokeissa havaittiin, että emäsmuotoinen IRA-743-hartsi toimii hyvin germaniumin talteenotossa myös kolonnissa. Pelkästään germaniumia ja kobolttia sisältäneellä liuoksella hartsin dynaamiseksi kapasiteetiksi saatiin 54 mg Ge/g. Germaniumin eluointi IRA-743:sta onnistui parhaiten 0,5 M H2SO4:lla. Kolonnikokeita IRA-743:lla ajettiin myös monimetallisilla liuoksilla, mutta silloin havaittiin hartsin kapasiteetin pienenevän hartsin myrkyttymisen takia.

Sensitive photonic system to measure oxidative potential of airborne nanoparticles and ROS levels in exhaled air

A photonic system has been developed that enables sensitive quantitative determination of reactive oxygen species (ROS) - mainly hydrogen peroxide (H2O2) - in aerosol samples such as airborne nanoparticles and exhaled air from patients. The detection principle relies on the amplification of the absorbance under multiple scattering conditions due to optical path lengthening [1] and [2]. In this study, the presence of cellulose membrane that acts as random medium into the glass optical cell considerably improved the sensitivity of the detection based on colorimetric FOX assay (FeII/orange xylenol). Despite the loss of assay volume (cellulose occupies 75% of cell volume) the limit of detection is enhanced by one order of magnitude reaching the value of 9 nM (H2O2 equivalents). Spectral analysis is performed automatically with a periodicity of 5 to 15 s, giving rise to real-time ROS measurements. Moreover, the elution of air sample into the collection chamber via a micro-diffuser (impinger) enables quantitative determination of ROS contained in or generated from airborne samples. As proof-of-concept the photonic ROS detection system was used in the determination of both ROS generated from traffic pollution and ROS contained in the exhaled breath as lung inflammation biomarkers.

Determinação de fósforo orgânico em águas de produção petrolífera por ICP- AES e ICP- MS após pré-concentração em coluna de sílica-C18

Results on the optimization of analytical methods for the determination of phosphorus in phosphino-polycarboxylate (PPCA), used frequently as scale inhibitor during oil production, by ICP-AES and ICP-MS are presented. Due to the complex matrix of production waters (brines) and their high concentration in inorganic phosphorus, the separation of organic phosphorus prior to its determination is necessary. In this work, minicolumns of silica immobilized C18 were used. Optimization of the separation step resulted in the following working conditions: (1) prewashing of the column with methanol (80% v/v); (2) use of a flow rate of 5 mL/min and 10 mL/min, respectively, for the preconditioning step and for percolation of the water sample; (3) final elution of organic phosphorus with 7 mL of buffer of H3BO3/NaOH (0.05 M, pH 9) with a flow rate of 1 mL/min. Sample detection limits (3s) for different combinations of nebulizers and spectrometric methods, based on 10 mL water aliquots, are: ICP-AES -Cross flow (47 mg/L) and Ultrasonic (18 mug/L); ICP-MS -Cross flow (1.2 mug/L), Cyclonic (0.7 mug/L) and Ultrasonic (0.5 mug/L). Typical recoveries of organic phosphorus are between 90 and 95% and the repeatability of the whole procedure is better than 10%. The developed methodology was applied successfully to samples from the oil-well NA 46, platform PNA 2, Campos basin, Brazil. Assessment of the PPCA inhibitor was possible at lower concentrations than achieved by current analytical methods, resulting in benefits such as reduced cost of chemicals, postponed oil production and lower environmental impacts.

Stabilization of the ionic form of weak acid cation exchange resins

Weak acid cation exchange (WAC) resins are used in the chromatographic separation of betaine from vinasse, a by-product of sugar industry. The ionic form of the resin determines the elution time of betaine. When a WAC-resin is in hydrogen form, the retention time of betaine is the longest and betaine elutes as the last component of vi-nasse from the chromatographic column. If the feed solution contains salts and its pH is not acidic enough to keep the resin undissociated, the ionic form of the hydrogen form resin starts to alter. Vinasse contains salts and its pH is around 5, it also contains weak acids. To keep the metal ion content (Na/H ratio) of the resin low enough to ensure successful separation of betaine, acid has to be added to either eluent (water) or vinasse. The aim of the present work was to examine by laboratory experiments which option requires less acid. Also the retention mechanism of betaine was investigated by measuring retention volumes of acetic acid and choline in different Na/H ratios of the resin. It was found that the resulting ionic form of the resin is the same regardless of whether the regeneration acid is added to the eluent or the feed solution (vinasse). Be-sides the salt concentration and the pH of vinasse, also the concentration of weak acids in the feed affects the resulting ionic form of the resin. The more buffering capacity vinasse has, the more acid is required to keep the ionic form of the resin desired. Vinasse was found to be quite strong buffer solution, which means relatively high amounts of acid are required to prevent the Na/H ratio from increasing too much. It is known that the retention volume of betaine decreases significantly, when the Na/H ratio increases. This is assumed to occur, because the amount of hydrogen bonds between the carboxylic groups of betaine and the resin decreases. Same behavior was not found with acetic acid. Choline has the same molecular structure as betaine, but instead of carboxylic group it has hydroxide group. The retention volume of choline increased as the Na/H ratio of the resin increased, because of the ion exchange reaction between choline cation and dissociated carboxylic group of the resin. Since the retention behavior of choline on the resin is opposite to the behavior of be-taine, the strong affinity of betaine towards hydrogen form WAC-resin has to be based on its carboxylic group. It is probable that the quaternary ammonium groups also affect the behavior of the carboxylic groups of betaine, causing them to form hydrogen bonds with the carboxylic groups of the resin.

New methods for the concentration of viruses from urban sewage using quantitative PCR.

Viruses are among the most important pathogens present in water contaminated with feces or urine and represent a serious risk to human health. Four procedures for concentrating viruses from sewage have been compared in this work, three of which were developed in the present study. Viruses were quantified using PCR techniques. According to statistical analysis and the sensitivity to detect human adenoviruses (HAdV), JC polyomaviruses (JCPyV) and noroviruses genogroup II (NoV GGII): (i) a new procedure (elution and skimmed-milk flocculation procedure (ESMP)) based on the elution of the viruses with glycine-alkaline buffer followed by organic flocculation with skimmed-milk was found to be the most efficient method when compared to (ii) ultrafiltration and glycine-alkaline elution, (iii) a lyophilization-based method and (iv) ultracentrifugation and glycine-alkaline elution. Through the analysis of replicate sewage samples, ESMP showed reproducible results with a coefficient of variation (CV) of 16% for HAdV, 12% for JCPyV and 17% for NoV GGII. Using spiked samples, the viral recoveries were estimated at 30-95% for HAdV, 55-90% for JCPyV and 45-50% for NoV GGII. ESMP was validated in a field study using twelve 24-h composite sewage samples collected in an urban sewage treatment plant in the North of Spain that reported 100% positive samples with mean values of HAdV, JCPyV and NoV GGII similar to those observed in other studies. Although all of the methods compared in this work yield consistently high values of virus detection and recovery in urban sewage, some require expensive laboratory equipment. ESMP is an effective low-cost procedure which allows a large number of samples to be processed simultaneously and is easily standardizable for its performance in a routine laboratory working in water monitoring. Moreover, in the present study, a CV was applied and proposed as a parameter to evaluate and compare the methods for detecting viruses in sewage samples.

New methods for the concentration of viruses from urban sewage using quantitative PCR.

Viruses are among the most important pathogens present in water contaminated with feces or urine and represent a serious risk to human health. Four procedures for concentrating viruses from sewage have been compared in this work, three of which were developed in the present study. Viruses were quantified using PCR techniques. According to statistical analysis and the sensitivity to detect human adenoviruses (HAdV), JC polyomaviruses (JCPyV) and noroviruses genogroup II (NoV GGII): (i) a new procedure (elution and skimmed-milk flocculation procedure (ESMP)) based on the elution of the viruses with glycine-alkaline buffer followed by organic flocculation with skimmed-milk was found to be the most efficient method when compared to (ii) ultrafiltration and glycine-alkaline elution, (iii) a lyophilization-based method and (iv) ultracentrifugation and glycine-alkaline elution. Through the analysis of replicate sewage samples, ESMP showed reproducible results with a coefficient of variation (CV) of 16% for HAdV, 12% for JCPyV and 17% for NoV GGII. Using spiked samples, the viral recoveries were estimated at 30-95% for HAdV, 55-90% for JCPyV and 45-50% for NoV GGII. ESMP was validated in a field study using twelve 24-h composite sewage samples collected in an urban sewage treatment plant in the North of Spain that reported 100% positive samples with mean values of HAdV, JCPyV and NoV GGII similar to those observed in other studies. Although all of the methods compared in this work yield consistently high values of virus detection and recovery in urban sewage, some require expensive laboratory equipment. ESMP is an effective low-cost procedure which allows a large number of samples to be processed simultaneously and is easily standardizable for its performance in a routine laboratory working in water monitoring. Moreover, in the present study, a CV was applied and proposed as a parameter to evaluate and compare the methods for detecting viruses in sewage samples.

Caracterização de quitosana por Cromatografia de Permeação em Gel - Influência do método de preparação e do solvente

In this work, samples of chitosan obtained in different conditions were characterized by molecular weight distribution, using Gel Permeation Chromatography (GPC), in two different solvents. It was observed that the increase in the number of deacetylation steps promotes a increase in the degree of deacetylation followed by a decrease in the average of molecular weight and polydispersion. The GPC curves obtained for chitosan samples in the two solvents used (CH3COOH 0.30 mol/dm³ - CH3CONa 0.20 mol/dm³ and CH3COOH 0.10 mol/dm³ - NaCl 0.20 mol/dm³) showed small difference in elution volume, but significant changes in the average molecular weight (Mn and Mw) and polydispersion that, in agree with the values of Huggins constant, present evidences of chitosan aggregates formation in the second solvent.

Alternativa analítica para especiação físico-química de mercúrio em águas costeiras tropicais

The determination of the physical-chemical mercury speciation in tropical coastal waters using the derivatization technique with CVAFS detection was optimized. This methodology is able to separate the elementary, reactive, organic and total mercury phases with low operational costs. The importance of bromide chloride solution, the diluted aqua regia, used as the oxidative solution, and different compositions of the reductive solution of stannous chloride were tested and the better results for coastal waters are presented. The recuperation of the sum of the different phases ranges from 80 to 94% of the total Hg content in duplicates of different marine samples. The optimized methodology permits important studies on the mercury cycle in the coastal environment.

Determinação espectrofotométrica de alumínio em concentrados salinos utilizados em hemodiálise empregando pré-concentração em fluxo

An automatic flow injection procedure for spectrophotometric aluminium determination in purified water and solutions containing high salts concentrations used for hemodyalisis treatment was developed. The method was base on reaction of Al3+ with cianine eriochrome R (ECR) after preconcentration using the AG50W-X8 cationic-exchange resin. Elution was carried out using a 1 % (m/v) calcium chloride solution. The manifold comprised an automatic proporcional injector controlled by a computer equipped with an eletronic interface and software written in QuicBASIC 4.5 with facilities to control the injector and perform data acquisition. Samples with concentration ranging from 4.96 to 19.90 µg L-1 Al were analyzed and recoveries between 88 and 113% were obtained by using the standard addition method. Other profitable analytical characteristics such as a relative standard deviation 1.3 % (n = 10) for a typical sample 14.5 µg L-1 Al, a linear response ranging up to 60.0 µg L-1Al, and a sampling throughput of 10 determinations per hour were achieved. A detection limit of 4.2 µg L-1 Al was estimated as suggested by IUPAC.