Direct Access to Oxidation-Resistant Nickel Catalysts through an Organometallic Precursor

The synthesis of nickel catalysts for industrial applications is relatively simple; however, nickel oxidation is usually difficult to avoid, which makes it challenging to optimize catalytic activities, metal loadings, and high-temperature activation steps. A robust, oxidation-resistant and very active nickel catalyst was prepared by controlled decomposition of the organometallic precursor [bis(1,5-cyclooctadiene)nickel(0)], Ni(COD)(2), over silica-coated magnetite (Fe3O4@SiO2). The sample is mostly Ni(0), and surface oxidized species formed after exposure to air are easily reduced in situ during hydrogenation of cyclohexene under mild conditions recovering the initial activity. This unique behavior may benefit several other reactions that are likely to proceed via Ni heterogeneous catalysis.

Recent Advances in the Development of Magnetically Recoverable Metal Nanoparticle Catalysts

The aim of this Account is to provide an overview of our current research activities on the design and modification of superparamagnetic nanomaterials for application in the field of magnetic separation and catalysis. First, an introduction of magnetism and magnetic separation is done. Then, the synthetic strategies that have been developed for generating superparamagnetic nanoparticles spherically coated by silica and other oxides, with a focus on well characterized systems prepared by methods that generate samples of high quality and easy to scale- up, are discussed. A set of magnetically recoverable catalysts prepared in our research group by the unique combination of superparamagnetic supports and metal nanoparticles is highlighted. This Account is concluded with personal remarks and perspectives on this research field.

Magnetic nanohydrometallurgy: A promising nanotechnological approach for metal production and recovery using functionalized superparamagnetic nanoparticles

We report on a new, promising nanotechnological approach for hydrometallurgy based on recyclable, chemically functionalized superparamagnetic nanoparticles. In this process, the metal ions (e.g. Cu2+) are captured by the nanoparticles and confined at the electrode surface by means of an external magnet. Due to the pre-concentration effect the electrodeposition process is greatly improved, yielding the pure metal in a much shorter time in comparison with the conventional electrodeposition process. After the electrolysis, the magnetic nanoparticles are ready to return to the process. The proposed strategy can advantageously be incorporated in hydrometallurgy, reducing the number of steps associated with complexation, organic solvent extraction, metal release and diffusional electroprocessing, leading to a more sustainable technology. (C) 2012 Elsevier B.V. All rights reserved.

Synthesis of supported metal nanoparticle catalysts using ligand assisted methods

The synthesis and characterization methods of metal nanoparticles (NPs) have advanced greatly in the last few decades, allowing an increasing understanding of structure-property-performance relationships. However, the role played by the ligands used as stabilizers for metal NPs synthesis or for NPs immobilization on solid supports has been underestimated. Here, we highlight some recent progress in the preparation of supported metal NPs with the assistance of ligands in solution or grafted on solid supports, a modified deposition-reduction method, with special attention to the effects on NPs size, metal-support interactions and, more importantly, catalytic activities. After presenting the general strategies in metal NP synthesis assisted by ligands grafted on solid supports, we highlight some recent progress in the deposition of pre-formed colloidal NPs on functionalized solids. Another important aspect that will be reviewed is related to the separation and recovery of NPs. Finally, we will outline our personal understanding and perspectives on the use of supported metal NPs prepared through ligand-assisted methods.

Effetto di un packaging innovativo sulla qualità di nettarine

L’imballaggio alimentare si può definire come un sistema coordinato per disporre i beni per il trasporto, la distribuzione, la conservazione, la vendita e l’utilizzo. Uno dei materiali maggiormente impiegati, nell’industria alimentare, per la produzione di imballaggi sono le materie plastiche. Esse sono sostanze organiche derivanti da petrolio greggio, sono composti solidi allo stato finito, ma possono essere modellate allo stato fluido. Un imballaggio alimentare deve svolgere determinate funzioni tra cui: - contenimento del prodotto - protezione del prodotto da agenti esterni - logistica - comunicativa - funzionale - ecologica L'ultimo punto sopracitato è il principale problema delle materie plastiche derivanti dal petrolio greggio. Questi materiali sono difficilmente riciclabili perché spesso un imballaggio è composto da più materiali stratificati o perché si trova a diretto contatto con gli alimenti. Inoltre questi materiali hanno un lungo tempo di degradazione (da 100 a 1000 anni) che ne rendono difficile e costoso lo smaltimento. Per questo nell’ultimo decennio è cominciata la ricerca di un materiale plastico, flessibile alle esigenze industriali e nel contempo biodegradabile. Una prima idea è stata quella di “imitare la natura” cercando di replicare macromolecole già esistenti (derivate da amido e zuccheri) per ottenere una sostanza plastico-simile utilizzabile per gli stessi scopi, ma biodegradabile in circa sei mesi. Queste bioplastiche non hanno preso piede per l’alto costo di produzione e perché risulta impossibile riconvertire impianti di produzione in tutto il mondo in tempi brevi. Una seconda corrente di pensiero ha indirizzato i propri sforzi verso l’utilizzo di speciali additivi aggiunti in minima misura (1%) ai classici materiali plastici e che ne permettono la biodegradazione in un tempo inferiore ai tre anni. Un esempio di questo tipo di additivi è l’ECM Masterbatch Pellets che è un copolimero di EVA (etilene vinil acetato) che aggiunto alle plastiche tradizionali rende il prodotto finale completamente biodegradabile pur mantenendo le proprie caratteristiche. Scopo di questo lavoro di tesi è stato determinare le modificazioni di alcuni parametri qualitativi di nettarine di Romagna(cv.-Alexa®) confezionate-con-film-plastici-tradizionali-e-innovativi. I campioni di nettarine sono stati confezionati in cestini in plastica da 1 kg (sigillati con un film flow-pack macroforato) di tipo tradizionale in polipropilene (campione denominato TRA) o vaschette in polipropilene additivato (campione denominato BIO) e conservati a 4°C e UR 90-95% per 7 giorni per simulare un trasporto refrigerato successivamente i campioni sono stati posti in una camera a 20°C e U.R. 50% per 4 giorni al fine di simulare una conservazione al punto vendita. Al tempo 0 e dopo 4, 7, 9 e 11 giorni sono state effettuate le seguenti analisi: - coefficiente di respirazione è stato misurata la quantità di CO2 prodotta - indice di maturazione espresso come rapporto tra contenuto in solidi solubili e l’acidità titolabile - analisi di immagine computerizzata - consistenza della polpa del frutto è stata misurata attraverso un dinamometro Texture Analyser - contenuto in solidi totali ottenuto mediante gravimetria essiccando i campioni in stufa sottovuoto - caratteristiche sensoriali (Test Accettabilità) Conclusioni In base ai risultati ottenuti i due campioni non hanno fatto registrare dei punteggi significativamente differenti durante tutta la conservazione, specialmente per quanto riguarda i punteggi sensoriali, quindi si conclude che le vaschette biodegradabili additivate non influenzano la conservazione delle nettarine durante la commercializzazione del prodotto limitatamente ai parametri analizzati. Si ritiene opportuno verificare se il processo di degradazione del polimero additivato si inneschi già durante la commercializzazione della frutta e soprattutto verificare se durante tale processo vengano rilasciati dei gas che possono accelerare la maturazione dei frutti (p.e. etilene), in quanto questo spiegherebbe il maggiore tasso di respirazione e la più elevata velocità di maturazione dei frutti conservati in tali vaschette. Alimentary packaging may be defined as a coordinate system to dispose goods for transport, distribution, storage, sale and use. Among materials most used in the alimentary industry, for the production of packaging there are plastics materials. They are organic substances deriving from crude oil, solid compounds in the ended state, but can be moulded in the fluid state. Alimentary packaging has to develop determinated functions such as: - Product conteniment - Product protection from fieleders agents - logistic - communicative - functional - ecologic This last term is the main problem of plastic materials deriving from crude oil. These materials are hardly recyclable because a packaging is often composed by more stratified materials or because it is in direct contact with aliments. Beside these materials have a long degradation time(from 100 to 1000 years) that make disposal difficult and expensive. For this reason in the last decade the research for a new plastic material is begin, to make industrial demands more flexible and, at the same time, to make this material biodegradable: At first, the idea to “imitate the nature” has been thought, trying to reply macromolecules already existents (derived from amid and sugars) to obtain a similar-plastic substance that can be used for the same purposes, but it has to be biodegradable in about six months. These bioplastics haven’t more success bacause of the high production cost and because reconvert production facilities of all over the wolrd results impossible in short times. At second, the idea to use specials addictives has been thought. These addictives has been added in minim measure (1%) to classics plastics materials and that allow the biodegradation in a period of time under three years. An example of this kind of addictives is ECM Masterbatch Pellets which is a coplymer of EVA (Ethylene vinyl acetate) that, once it is added to tradizional plastics, make final product completely biodegradable however maintaining their own attributes. The objective of this thesis work has been to determinate modifications of some Romagna’s Nectarines’ (cv. Alexa®) qualitatives parameters which have been packaged-with traditional and innovative-plastic film. Nectarines’ samples have been packaged in plastic cages of 1 kg (sealed with a macro-drilled flow-pack film) of traditional type in polypropylene (sample named TRA) or trays in polypropylene with addictives (sample named BIO) and conservated at 4°C and UR 90-95% for 7 days to simulate a refrigerated transport. After that, samples have been put in a camera at 20°C and U.R. 50% for 4 days to simulate the conservation in the market point. At the time 0 and after 4, 7, 9 and 11 days have been done the following analaysis: - Respiration coefficient wherewith the amount CO2 producted has been misurated - Maturation index which is expressed as the ratio between solid soluble content and the titratable acidity - Analysis of computing images - Consistence of pulp of the fruit that has been measured through Texture Analyser Dynanometer - Content in total solids gotten throught gravimetry by the drying of samples in vacuum incubator - Sensorial characteristic (Panel Test) Consequences From the gotten results, the two samples have registrated no significative different scores during all the conservation, expecially about the sensorial scores, so it’s possible to conclude that addictived biodegradable trays don’t influence the Nectarines’ conservation during the commercialization of the product qualifiedly to analized parameters. It’s advised to verify if the degradation process of the addicted polymer may begin already during the commercialization of the fruit and in particular to verify if during this process some gases could be released which can accelerate the maturation of fruits (p.e. etylene), because all this will explain the great respiration rate and the high speed of the maturation of fruits conservated in these trays.

Industrial ecology applied to ELV management. Material and energy recovery from ASR

This PhD thesis reports on car fluff management, recycling and recovery. Car fluff is the residual waste produced by car recycling operations, particularly from hulk shredding. Car fluff is known also as Automotive Shredder Residue (ASR) and it is made of plastics, rubbers, textiles, metals and other materials, and it is very heterogeneous both in its composition and in its particle size. In fact, fines may amount to about 50%, making difficult to sort out recyclable materials or exploit ASR heat value by energy recovery. This 3 years long study started with the definition of the Italian End-of-Life Vehicles (ELVs) recycling state of the art. A national recycling trial revealed Italian recycling rate to be around 81% in 2008, while European Community recycling target are set to 85% by 2015. Consequently, according to Industrial Ecology framework, a life cycle assessment (LCA) has been conducted revealing that sorting and recycling polymers and metals contained in car fluff, followed by recovering residual energy, is the route which has the best environmental perspective. This results led the second year investigation that involved pyrolysis trials on pretreated ASR fractions aimed at investigating which processes could be suitable for an industrial scale ASR treatment plant. Sieving followed by floatation reported good result in thermochemical conversion of polymers with polyolefins giving excellent conversion rate. This factor triggered ecodesign considerations. Ecodesign, together with LCA, is one of the Industrial Ecology pillars and it consists of design for recycling and design for disassembly, both aimed at the improvement of car components dismantling speed and the substitution of non recyclable material. Finally, during the last year, innovative plants and technologies for metals recovery from car fluff have been visited and tested worldwide in order to design a new car fluff treatment plant aimed at ASR energy and material recovery.

New and More Sustainable Processes for the Synthesis of Phenolics: 2-phenoxyethanol and hydroxytyrosol

The research work has dealt with the study of new catalytic processes for the synthesis of fine chemicals belonging to the class of phenolics, namely 2-phenoxyethanol and hydroxytyrosol. The two synthetic procedures investigated have the advantages of being much closer to the Green Chemistry principles than those currently used industrially. In both cases, the challenge was that of finding catalysts and methods which led to the production of less waste, and used less hazardous chemicals, safer solvents, and reusable heterogeneous catalysts. In the case of 2-phenoxyethanol, the process investigated involves the use of ethylene carbonate (EC) as the reactant for phenol O-hydroxyethylation, in place of ethylene oxide. Besides being a safer reactant, the major advantage of using EC in the new synthesis is the better selectivity to the desired product achieved. Moreover, the solid catalyst based on Na-mordenite was fully recyclable. The reaction mechanism and the effect of the Si/Al ratio in the mordenite were investigated. In the case of hydroxytyrosol, which is one of the most powerful natural antioxidants, a new synthetic procedure was investigated; in fact, the method currently employed, the hydrolysis of oleuropein, an ester extracted from the waste water processing of the olive, makes use of large amounts of organic solvents (hexane, ethyl acetate), and involves several expensive steps of purification. The synthesis procedure set up involves first the reaction between catechol and 2,2-dimethoxyacetaldehyde, followed by the one-pot reduction of the intermediate to give the desired product. Both steps were optimized, in terms of catalyst used, and of reaction conditions, that allowed to reach ca 70% yield in each step. The reaction mechanism was investigated and elucidated. During a 3-month period spent at the University of Valencia (with Prof. A. Corma’s group), a process for the production of diesel additives (2,5-bis(propoxymethyl)furan) from fructose has been investigated.

Crystallization and morphology of the PLLA phase within random poly (L-lactide-ran-ɛ-caprolactone)

This work has mainly focused on the poly (L-lactide) (PLLA) which is a material for multiple applications with performances comparable to those of petrochemical polymers (PP, PS, PET, etc. ...), readily recyclable and also compostable. However, PLLA has certain shortcomings that limit its applications. It is a brittle, hard polymer with a very low elongation at break, hydrophobic, exhibits low crystallization kinetics and takes a long time to degrade. The properties of PLLA may be modified by copolymerization (random, block, and graft) of L-lactide monomers with other co-monomers. In this thesis it has been studied the crystallization and morphology of random copolymers poly (L-lactide-ran-ε-caprolactone) with different compositions of the two monomers since the physical, mechanical, optical and chemical properties of a material depend on this behavior. Thermal analyses were performed by differential scanning calorimetry (DSC) and thermogravimetry (TGA) to observe behaviors due to the different compositions of the copolymers. The crystallization kinetics and morphology of poly (L-lactide-ran-ε-caprolactone) was investigated by polarized light optical microscopy (PLOM) and differential scanning calorimetry (DSC). Their thermal behavior was observed with crystallization from melt. It was observed that with increasing amounts of PCL in the copolymer, there is a decrease of the thermal degradation. Studies on the crystallization kinetics have shown that small quantities of PCL in the copolymer increase the overall crystallization kinetics and the crystal growth rate which decreases with higher quantities of PCL.

Examining the Justification for Residential Recycling

Municipalities in the United States have for the past two decades initiated two policies to reduce residential solid waste generation by increasing recycling. The first policy, implemented in over 4,000 municipalities in the United States, requires households to pay a fee for each unit of garbage presented at the curb for collection. The second policy, initiated in 8,875 municipalities, subsidizes household recycling efforts by providing free curbside collection of certain recyclable materials. Both initiatives serve as examples of incentive-based environmental policies favored by many economists. But before economists can celebrate this wide-spread adoption of incentive-based environmental policies, further examination reveals that potentially inefficient command and control policies have been more instrumental in promoting recycling than might be commonly known. This article examines the empirical lessons gained from studying twenty years of solid waste policy in the United States and argues for the replacement of several state recycling mandates with a system of state and/or national landfill taxes.

Optimal Solid Waste Policy with Centralized Recycling Opportunities

Economic models have demonstrated the efficiency of curbside collection taxes. This paper demonstrates that such efficiencies disappear in economies with centralized recycling options - where recyclable materials can be removed from the waste stream either by households or at a centralized recycling facility. In such economies a curbside garbage tax not only fails to encourage the centralized recycler to internalize the external costs of waste disposal, but introduces inefficiencies to the cost-minimizing mix of household and centralized recycling efforts. The optimal waste policy is a tax assessed further downstream at the landfill rather than at the curb.

Evaluating Bucknell's Waste Stream

This thesis examines three questions regarding the content of Bucknell University‟s waste stream and the contributors to campus recycling and solid waste disposal. The first asks, “What does Bucknell‟s waste stream consist of?” To answer this question, I designed a campus-wide waste audit procedure that sampled one dumpster from each of the eleven „activity‟ types on campus in order to better understand Bucknell‟s waste composition. The audit was implemented during the Fall semester of the 2011-2012 school year. The waste from each dumpster was sorted into several recyclable and non-recyclable categories and then weighed individually. Results showed the Bison and Carpenter Shop dumpsters to contain the highest percentage of divertible materials (through recycling and/or composting). When extrapolated, results also showed the Dining Services buildings and Facilities buildings to be the most waste dense in terms of pounds of waste generated per square foot. The Bison also generated the most overall waste by weight. The average composition of all dumpsters revealed that organic waste composed 24% of all waste, 23% was non-recyclable paper, and 20% was non-recyclable plastic. It will be important to move forward using these results to help create effective waste programs that target the appropriate areas of concern. My second question asks, “What influences waste behavior to contribute to this „picture‟ of the waste stream?” To answer this question, I created a survey that was sent out to randomly selected sub-group of the university‟s three constituencies: students, faculty, and staff. The survey sought responses regarding each constituency‟s solid waste disposal and recycling behavior, attitudes toward recycling, and motivating factors for solid waste disposal behaviors across different sectors of the university. Using regression analysis, I found three statistically significant motivating factors that influence solid waste disposal behavior: knowledge and awareness, moral value, and social norms. I further examined how a person‟s characteristics associate to these motivating factors and found that one‟s position on campus proved a significant association. Consistently, faculty and staff were strongly influenced by the aforementioned motivating factors, while students‟ behavior was less influenced by them. This suggests that new waste programs should target students to help increase the influence of these motivators to improve the recycling rate and lower overall solid waste disposal on campus. After making overall conclusions regarding the waste audit and survey, I ask my third question, which inquires, “What actions can Bucknell take to increase recycling rates and decrease solid waste generation?” Bucknell currently features several recycling and waste minimization programs on campus. However, using results from the waste audit and campus survey, we can better understand what are the issues of the waste stream, how do we go about addressing these issues, and who needs to be addressed. I propose several suggestions for projects that future students may take on for summer or thesis research. Suggestions include targeting the appropriate categories of waste that occur most frequently in the waste stream, as well as the building types that have the highest waste density and potential recovery rates. Additionally, certain groups on campus should be targeted more directly than others, namely the student body, which demonstrates the lowest influence by motivators of recycling and waste behavior. Several variables were identified as significant motivators of waste and recycling behavior, and could be used as program tactics to encourage more effective behavior.

Determining the Socially Optimal Recycling Rate

What municipal recycling rate is socially optimal? One credible answer would consider the recycling rate that minimizes the overall social costs of managing municipal waste. Such social costs are comprised of all budgetary costs and revenues associated with operating municipal waste and recycling programs, all costs to recycling households associated with preparing and storing recyclable materials for collection, all external disposal costs associated with waste disposed at landfills or incinerators, and all external benefits associated with the provision of recycled materials that foster environmentally efficient production processes. This paper discusses how to estimate these four components of social cost to then estimate the optimal recycling rate. (C) 2013 Elsevier B.V. All rights reserved.

Twelve factors influencing sustainable recycling of municipal solid waste in developing countries

Sustainable management of solid waste is a global concern, as exemplified by the United Nations Millennium Development Goals (MDG) that 191 member states support. The seventh MDG indirectly advocates for municipal solid waste management (MSWM) by aiming to ensure environmental sustainability into countries’ policies and programs and reverse negative environmental impact. Proper MSWM will likely result in relieving poverty, reducing child mortality, improving maternal health, and preventing disease, which are MDG goals one, four, five, and six, respectively (UNMDG, 2005). Solid waste production is increasing worldwide as the global society strives to obtain a decent quality of life. Several means exist in which the amount of solid waste going to a landfill can be reduced, such as incineration with energy production, composting of organic wastes, and material recovery through recycling, which are all considered sustainable methods by which to manage MSW. In the developing world, composting is already a widely-accepted method to reduce waste fated for the landfill, and incineration for energy recovery can be a costly capital investment for most communities. Therefore, this research focuses on recycling as a solution to the municipal solid waste production problem while considering the three dimensions of sustainability environment, society, and economy. First, twenty-three developing country case studies were quantitatively and qualitatively examined for aspects of municipal solid waste management. The municipal solid waste (MSW) generation and recovery rates, as well as the composition were compiled and assessed. The average MSW generation rate was 0.77 kg/person/day, with recovery rates varying from 5 – 40%. The waste streams of nineteen of these case studies consisted of 0 – 70% recyclable material and 17 – 80% organic material. All twenty-three case studies were analyzed qualitatively by identifying any barriers or incentives to recycling, which justified the creation of twelve factors influencing sustainable municipal solid waste management (MSWM) in developing countries. The presence of regulations, enforcement of laws, and use of incentive schemes constitutes the first factor, Government Policy. Cost of MSWM operations, the budget allocated to MSWM by local to national governments, as well as the stability and reliability of funds comprise the Government Finances factor influencing recycling in the third world. Many case studies indicated that understanding features of a waste stream such as the generation and recovery rates and composition is the first measure in determining proper management solutions, which forms the third factor Waste Characterization. The presence and efficiency of waste collection and segregation by scavengers, municipalities, or private contractors was commonly addressed by the case studies, which justified Waste Collection and Segregation as the fourth factor. Having knowledge of MSWM and an understanding of the linkages between human behavior, waste handling, and health/sanitation/environment comprise the Household Education factor. Individuals’ income influencing waste handling behavior (e.g., reuse, recycling, and illegal dumping), presence of waste collection/disposal fees, and willingness to pay by residents were seen as one of the biggest incentives to recycling, which justified them being combined into the Household Economics factor. The MSWM Administration factor was formed following several references to the presence and effectiveness of private and/or public management of waste through collection, recovery, and disposal influencing recycling activity. Although the MSWM Personnel Education factor was only recognized by six of the twenty-two case studies, the lack of trained laborers and skilled professionals in MSWM positions was a barrier to sustainable MSWM in every case but one. The presence and effectiveness of a comprehensive, integrative, long-term MSWM strategy was highly encouraged by every case study that addressed the tenth factor, MSWM Plan. Although seemingly a subset of private MSWM administration, the existence and profitability of market systems relying on recycled-material throughput, involvement of small businesses, middlemen, and large industries/exporters is deserving of the factor Local Recycled-Material Market. Availability and effective use of technology and/or human workforce and the safety considerations of each were recurrent barriers and incentives to recycling to warrant the Technological and Human Resources factor. The Land Availability factor takes into consideration land attributes such as terrain, ownership, and development which can often times dictate MSWM. Understanding the relationships among the twelve factors influencing recycling in developing countries, made apparent the collaborative nature required of sustainable MSWM. Factors requiring the greatest collaborative inputs include waste collection and segregation, MSWM plan, and local recycled-material market. Aligning each factor to the societal, environmental, and economic dimensions of sustainability revealed the motives behind the institutions contributing to each factor. A correlation between stakeholder involvement and sustainability existed, as supported by the fact that the only three factors driven by all three dimensions of sustainability were the same three that required the greatest collaboration with other factors. With increasing urbanization, advocating for improved health for all through the MDG, and changing consumption patterns resulting in increasing and more complex waste streams, the utilization of the collaboration web offered by this research is ever needed in the developing world. Through its use, the institutions associated with each of the twelve factors can achieve a better understanding of the collaboration necessary and beneficial for more sustainable MSWM.

Does Quality Matter in the Iron and Scrap Trade?

This paper sheds light on the iron and steel (IS) scrap trade to examine how economic development affects the quality demanded of recyclable resource. A simple model is presented that show a mechanism of how scrap quality impacts the direction of trade due to comparative advantage. We find that economic development in both importing and exporting countries has a positive effect on the quality of traded recyclables. Developed countries that intend to improve the domestic recovery of recyclables should raise the quality of separating recyclables while developing countries should tighten environmental regulations to help decrease the import of recyclables that cause pollution.

Determinación de propiedades de inflamabilidad de mezclas para co-combustión

La recuperación de energía a partir de biomasa y residuos no reciclables por la combustión está cobrando una notable importancia actualmente. Una de las técnicas más utilizadas para esta propuesta es la co-combustión de mezclas de residuos y biomasa. Con esta nueva tecnología, mezclas de diferentes materiales han aparecido en las instalaciones industriales y tienen que ser reconocidas como nuevos combustibles, debido a que a sus propiedades son aún desconocidas. Estas propiedades incluyen las energéticas, que son el objetivo del proceso de mezcla, y también las propiedades de inflamabilidad. Residuos y biomasa en forma de polvos tienen propiedades de ignición que se han de tener en cuenta a la hora de diseñar las medidas de prevención y protección en una instalación industrial. El objetivo principal de este estudio es determinar el riesgo de ignición de las mezclas de residuos / biomasa en capas y cómo, mediante la adición de diferentes cantidades de estos materiales, este riesgo puede cambiar. Para desarrollar este estudio, se utiliza la temperatura mínima de ignición en la capa. Tres muestras diferentes han sido analizadas, lodos con secado térmico de depuradora, paja de trigo y virutas de madera, Abstract Energy recovery from biomass and non-recyclable waste products by combustion has become important. One of the most used techniques for this proposal is the co-firing of waste and biomass mixtures, With this new technology, mixtures of different materials have appeared in the industrial facilities and they have to be treated as new fuels because their properties are unknown. Among this properties we include energetic properties that are the objective of the mixing process, and also the ignitability properties. Waste and biomass dusts have ignition properties that have to be taken into account in the design but also in the, prevention and protection process of an industrial facility.. The main objective of this research is to determine the risk of ignition of waste / biomass mixtures layers and how, by adding different quantities of these materials, this risk may vary. To develop this, the minimum ignition temperature on layer is used. Three different samples have been analysed, thermally dried sewage sludge, wheat straw and wood chips.