Post-tensioning of glulam timber with steel tendons

This paper describes a series of four-point bending tests that were conducted, under service loads and to failure, on unreinforced, reinforced and post-tensioned glulam timber beams, where the reinforcing tendon used was 12 mm diameter toughened steel bar. The research was designed to evaluate the benefits offered by including an active reinforcement in contrast to the passive reinforcement typically used within timber strengthening works, in addition to establishing the effect that bonding the reinforcing tendon has on the materials performance.

The laboratory investigations established that the flexural strength and stiffness increased for both the reinforced and post-tensioned timbers compared to the unreinforced beams. The flexural strength of the reinforced timber increased by 29.4%, while the stiffness increased by 28.1%. Timber that was post-tensioned with an unbonded steel tendon showed a flexural strength increase of 17.6% and an increase in stiffness of 8.1%. Post-tensioned beams with a bonded steel tendon showed increases in flexural strength and stiffness of 40.1% and 30% respectively.

Post-tensioning glulam timber beams with basalt FRP tendons

Improvements in the structural performance of glulam timber beams by the inclusion of reinforcing materials can increase both the service performance and ultimate capacity. This paper describes a series of four-point bending tests conducted, under service loads and to failure, on unreinforced, reinforced and post-tensioned glulam timber beams, where the reinforcing tendon used is 12 mm dia. basalt fibre-reinforced polymer. The research is designed to evaluate the benefits offered by including an active reinforcement in contrast to the passive reinforcement typically used within timber strengthening works, in addition to establishing the effect that bonding the reinforcing tendon has on the material's performance. Further experimental tests have also been developed to investigate the long-term implications of this research, with emphasis placed upon creep and loss of post-tensioning; however, this is ongoing and is not presented in this paper. The laboratory investigations establish that the flexural strength and stiffness increase for both the unbonded and bonded post-tensioned timbers compared to the unreinforced and reinforced beams. Timber that is post-tensioned with an unbonded basalt fibre-reinforced polymer tendon shows a flexural strength increase of 2ṡ8% and an increase in stiffness of 8ṡ7%. Post-tensioned beams with a bonded basalt fibre-reinforced polymer tendon show increases in flexural strength and stiffness of 15ṡ4% and 11ṡ5% respectively.

Development of Novel Post-Tensioned Glulam Timber Composites

Improvements in the structural performance of glulam timber beams by the inclusion of reinforcing materials can increase both the service performance and ultimate capacity. In recent years research focusing on the addition of fibre reinforced polymers (FRP) to strengthen members has yielded positive results. However, the FRP material is still relatively expensive and its full potential in combination with structural timber has not been realised. This paper describes a series of four-point bending tests that were conducted, under service loads and to failure, on unreinforced, reinforced and post-tensioned glulam timber beams, where the reinforcing tendon used was 12mm diameter basalt fibre reinforced polymer (BFRP). The research was designed to evaluate the benefits offered by including an active reinforcement in contrast to the passive reinforcement typically used within timber strengthening works, in addition to establishing the affect that bonding the reinforcing tendon has on the material’s performance. Further experimental tests have been developed to investigate the long-term implications of this research, with emphasis placed upon creep and loss of post-tensioning.
The laboratory investigations established that the flexural strength and stiffness increased for both the unbonded and bonded post-tensioned timbers compared to the unreinforced beams. Timber that was post-tensioned with an unbonded BFRP tendon showed a flexural strength increase of 2.8% and an increase in stiffness of 8.7%. Post-tensioned beams with a bonded BFRP tendon showed increases in flexural strength and stiffness of 16.6% and 11.5% respectively.

Strength and ductility of RC jacketed columns: a simplified analytical method

Reinforced concrete (RC) jacketing is a common method for retrofitting existing columns with poor structural performance. It can be applied in two different ways: if the continuity of the jacket is ensured, the axial load of the column can be transferred to the jacket, which will be directly loaded; conversely, if no continuity is provided, the jacket will induce only confinement action. In both cases the strength and ductility evaluation is rather complex, due to the different physical phenomena included, such as confinement, core-jacket composite action, preload and buckling of longitudinal bars.
Although different theoretical studies have been carried out to calculate the confinement effects, a practical approach to evaluate the flexural capacity and ductility is still missing. The calculation of these quantities is often related to the use of commercial software, taking advantage of numerical methods such as fibre method or finite element method.
This paper presents a simplified approach to calculate the flexural strength and ductility of square RC jacketed sections subjected to axial load and bending moment. In particular the proposed approach is based on the calibration of the stress-block parameters including the confinement effect. Equilibrium equations are determined and buckling of longitudinal bars is modelled with a suitable stress-strain law. Moment-curvature curves are derived with simple calculations. Finally, comparisons are made with numerical analyses carried out with the code OpenSees and with experimental data available in the literature, showing good agreement.

Effects of dietary restraint and oral contraceptives on bone strength and bone turnover in young women

ABSTRACT Introduction The purpose of this study was to assess specific osteoporosis-related health behaviours and physiological outcomes including daily calcium intake, physical activity levels, bone strength, as assessed by quantitative ultrasound, and bone turnover among women between the ages of 18 and 25. Respective differences on relevant study variables, based on dietary restraint and oral contraceptive use were also examined. Methods One hundred women (20.6 ± 0.2 years of age) volunteered to participate in the study. Informed written consent was obtained by all subjects prior to participation. The study and all related procedures were approved by the Brock University Research Ethics Board. Body mass, height, relative body fat, as well as chest, waist and hip circumferences were measured using standard procedures. The 10-item restrained eating subscale of the Dutch Eating Behaviour Questionnaire (DEBQ) was used to assess dietary restraint (van Strien et al., 1986). Daily calcium intake was assessed by the Rapid Assessment Method (RAM) (Hertzler & Frary 1994). Weekly physical activity was documented by the 4-item Godin Leisure-Time Exercise Questionnaire (Godin & Shephard 1985). Bone strength was determined from the speed of sound (SOS) as measured by QUS (Sunlight 7000S). SOS measurements (m/s) were taken of the dominant and non-dominant sides of the distal one third of the radius and the mid-shaft of the tibia. Resting blood samples were collected from all subjects between 9am and 12pm, in order to evaluate the impact of lifestyle factors on biochemical markers of bone turnover. Blood was collected during the early follicular phase of the menstrual cycle (approximately days 1-5) for all subjects. Samples were centrifliged and the serum or plasma was aliquoted into separate tubes and stored at -80°C until analysis. The bone formation markers measured were Osteocalcin (OC), bone specific alkaline phosphatase (BAP) and 25-OH vitamin D. The bone resorption markers measured were the carboxy (CTx) and amino (NTx) terminal telopeptides of type-I collagen crosslinks. All markers were assessed by ELISA. Subjects were divided into high (HDR) and low dietary restrainers (LDR) based on the median DEBQ score, and also into users (BC) and non-users (nBC) of oral contraceptives. A series of multiple one way ANOVA's were then conducted to identify differences between each set of groups for all relevant variables. A two-way ANOVA analysis was used to explore significant interactions between dietary restraint and use of oral contraceptives while a univariate follow-up analysis was also performed when appropriate. Pearson Product Moment Correlations were used to determine relationships among study variables. Results HDR had significantly higher BMI, %BF and circumference measures but lower daily calcium intake than LDR. There were no significant differences in physical activity levels between HDR and LDR. No significant differences were found between BC and nBC in body composition, calcium intake and physical activity. HDR had significantly lower tibial SOS scores than LDR in both the dominant and non-dominant sites. The post-hoc analysis showed that within the non-birth control group, the HDR had significantly lower tibial SOS scores of bone strength when compared to the LDR but Aere were no significant differences found between the two dietary restraint groups for those currently on birth control. HDR had significantly lower levels of OC than LDR and the BC group had lower levels of BAP than the nBC group. Consistently, the follow-up analysis revealed that within those not on birth control, subjects who were classified as HDR had significantly (f*<0.05) lower levels of OC when compared with LDR but no significant differences were observed in bone turnover between the two dietary restraint groups for those currently on birth control. Physical activity was not correlated with SOS scores and bone turnover markers possibly due to the low physical activity variability in this group of women. Conclusion This is the first study to examine the effects of dietary restraint on bone strength and turnover among this population of women. The most important finding of this study was that bone strength and turnover are negatively influenced by dietary restraint independent of relative body fat. In general, the results of the present thesis suggest that dietary restraint, oral contraceptive use, as well as low daily calcium intake and low physical activity levels were widespread behaviours among this population of college-aged women. The young women who were using dietary restraint as a strategy to lose weight, and thus were in the HDR group, despite their higher relative body fat and weight, had lower scores of bone strength and lower levels of markers of bone turnover compared to the low dietary restrainers. Additionally, bone turnover seemed to be negatively affected by oral contraceptives, while bone strength, as assessed by QUS, seemed unaffected by their use in this population of young women. Physical activity (weekly energy expenditure), on the other hand, was not associated with either bone strength or bone tiimover possibly due to the low variability of this variable in this population of young Canadian women.

Test of Hockman and Oldham's job characteristics model in a post-secondary educational setting

One hundred and seventy-two subj ects participated in this quantitative, correlational survey which tested Hackman and Oldham's Job Characteristics Model in an educational setting. Subjects were Teaching Masters, Chairmen and Deans from an Ontario community college. The data were collected via mailed questionnaire, on all variables of the model. Several reliable, valid instruments were used to test the variables. Data analysis through Pearson correlation and stepwise multiple regression analyses revealed that core job characteristics predicted certain critical psychological states and that these critical psychological states, in turn were able to predict various personal and work outcomes but not absenteeism. The context variable, Satisfaction with Co-workers, was the only consistent moderating variable between core characteristics and critical psychological states; however, individual employee differences did moderate the relationship between critical psychological states and all of the personal and work outcomes except Internal Work Motivation. Two other moderator variables, Satisfaction with Context and Growth Need Strength, demonstrated an ability to predict the outcome General Job Satisfaction. The research suggests that this model may be used for job design and redesign purposes within the community college setting.

Effects of Plyometric and Resistance Training on Muscle Strength and Neuromuscular Function in Young Adolescent Soccer Players

This study examined the effect of 8-weeks of resistance (RT) and plyometric (PLYO) training on maximal strength, power and jump performance compared with no added training (CON), in young male soccer players. Forty-one 11-13 year-old soccer players were divided into three groups (RT, PLYO, CON). All participants completed 5 isometric knee extensions at 90° and 5 isokinetic knee extensions at 240°/s pre- and post-training. Peak torque (PT), peak rate of torque development (pRTD), electromechanical-day (EMD), rate of muscle activation (Q30), muscle cross-sectional area (mCSA) and jump performance were examined. Both RT and PLYO resulted in significant (p < 0.05) increases in PT, pRTD and jump performance. RT resulted in significantly greater increases in both isometric and isokinetic PT, while PLYO resulted in significantly greater increases in isometric pRTD and jump performance compared with CON (p < 0.05). Q30 increased to a greater extent in PLYO (20%) compared with RT (5%) and CON (-5%) (p = 0.1). In conclusion, 8-weeks of RT and PLYO resulted in significant improvements in muscle strength and jump performance. RT appears to be more effective at eliciting increases in maximal strength while PLYO appears to enhance explosive strength, mediated by possible increases in the rate of muscle activation.

Évaluation de la reconstruction des ligaments croisés post luxation aiguë du genou avec l’utilisation des ligaments synthétiques

La luxation du genou, bien que très rare, demeure une blessure dévastatrice car elle entraîne de multiples complications en raison de la nature complexe du traumatisme associé à cette lésion. La luxation peut résulter d'un traumatisme à haute ou basse énergie. Les blessures sévères aux ligaments et aux structures associées donnent à la luxation du genou un potentiel élevé d'atteinte fonctionnelle. Le traitement conservateur, qui était considéré comme acceptable auparavant, est maintenant réservé à un très faible pourcentage de patients. La reconstruction chirurgicale est maintenant préconisée dans la plupart des cas, mais de nombreuses options existent et le traitement chirurgical optimal à préconiser reste controversé. Certains chirurgiens recommandent la reconstruction complète de tous les ligaments endommagés le plus tôt possible, tandis que d'autres, craignant l’établissement d’arthrofibrose, limitent l'intervention chirurgicale immédiate à la reconstruction du ligament croisé postérieur et de l'angle postéro-externe. En raison des multiples structures endommagées lors d’une luxation du genou, les chirurgiens utilisent couramment la combinaison des autogreffes et des allogreffes pour compléter la reconstruction ligamentaire. Les complications associées au prélèvement de la greffe, l'allongement de la greffe, l’affaiblissement précoce du greffon ainsi que les risques de transmission de maladies ont poussé les chirurgiens à rechercher différentes options d’intervention. L'utilisation de matériaux synthétiques pour le remplacement du ligament lésé a été proposée dans les années ´80. Après une première vague d'enthousiasme, les résultats décevants à long terme et les taux élevés d'échec ont diminué sa popularité. Depuis lors, une nouvelle génération de ligaments artificiels a vu le jour et parmi eux, le Ligament Advanced Reinforced System (LARS) a montré des résultats prometteurs. Il a été utilisé récemment dans les reconstructions isolées du ligament croisé antérieur et du ligament croisé postérieur pour lesquelles il a montré de bons résultats à court et moyen termes. Le but de cette étude rétrospective était d'évaluer la fonction et la stabilité du genou après la luxation aiguë suivant la reconstruction des ligaments croisés avec le ligament artificiel de type LARS. Cette étude a évalué 71 patients présentant une luxation du genou et qui ont subi une chirurgie de reconstruction du ligament croisé antérieur et du ligament croisé postérieur à l'aide du ligament LARS. Suite à la chirurgie le même protocole intensif de réadaptation a été suivi pour tous les patients, où la mise en charge progressive était permise après une période d’environ 6 semaines pendant laquelle la force musculaire et la stabilité dynamique se rétablissaient. Les outils d’évaluation utilisés étaient le score Lysholm, le formulaire de «l’International Knee Documentation Committee», le «Short Form-36», les tests cliniques de stabilité du genou, l'amplitude de mouvement articulaire à l’aide d’un goniomètre et la radiographie en stress Telos à 30° et 90° de flexion du genou. Le même protocole d’évaluation a été appliqué au genou controlatéral pour des fins de comparaison. Les résultats subjectifs et objectifs de cette étude sont satisfaisants et suggèrent que la réparation et la reconstruction combinées avec ligaments LARS est une alternative valable pour le traitement des luxations aiguës du genou. Ces résultats démontrent que ces interventions produisent des effets durables en termes d’amélioration de la fonction et révèlent la durabilité à long terme des ligaments artificiels LARS. Les patients sont à la fois plus autonomes et plus satisfaits avec le temps, même si la luxation du genou est considérée comme une catastrophe au moment où elle se produit. Des études prospectives randomisées sont maintenant nécessaires afin de comparer la sélection de la greffe et le délai de reconstruction chirurgicale.

Indirect Bonding Method: in vitro Comparison of the Shear Bond Strength between Metallic Orthodontic Brackets and Different Porcelain Surface Preparations

Introduction : La force d’adhésion à l'interface métal-céramique avec les résines auto-polymérisantes destinées au collage indirect des boîtiers orthodontiques n'a pas été évaluée à ce jour et un protocole clinique basé sur la littérature scientifique est inexistant. Objectifs : 1) Comparer la force de cisaillement maximale entre des boîtiers métalliques et des surfaces en porcelaine préparées selon différentes méthodes; 2) Suggérer un protocole clinique efficace et prévisible. Matériel et méthodes : Quatre-vingt-dix disques en leucite (6 groupes; n = 15/groupe) ont été préparés selon 6 combinaisons de traitements de surface : mécaniques (+ / - fraisage pour créer les rugosités) et chimiques (acide fluorhydrique, apprêt, silane). Des bases en résine composite Transbond XT (3M Unitek, Monrovia, California) faites sur mesure ont été collées avec le système de résine adhésive auto-polymérisante Sondhi A + B Rapid Set (3M Unitek, Monrovia, California). Les échantillons ont été préservés (H2O/24hrs), thermocyclés (500 cycles) et testés en cisaillement (Instron, Norwood, Massachusetts). Des mesures d’Index d’adhésif résiduel (IAR) ont été compilées. Des tests ANOVAs ont été réalisés sur les rangs étant donné que les données suivaient une distribution anormale et ont été ajustés selon Tukey. Un Kruskall-Wallis, U-Mann Whitney par comparaison pairée et une analyse de Weibull ont aussi été réalisés. Résultats : Les médianes des groupes varient entre 17.0 MPa (- fraisage + acide fluorhydrique) à 26.7 MPa (- fraisage + acide fluorhydrique + silane). Le fraisage en surface ne semble pas affecter l’adhésion. La combinaison chimique (- fraisage + silane + apprêt) a démontré des forces de cisaillement significativement plus élevées que le traitement avec (- fraisage + acide fluorhydrique), p<0,05, tout en possédant des forces similaires au protocole typiquement suggéré à l’acide fluorhydrique suivi d’une application de silane, l’équivalence de (- fraisage + acide fluorhydrique + silane). Les mesures d’IAR sont significativement plus basses dans le groupe (- fraisage + acide fluorhydrique) en comparaison avec celles des 5 autres groupes, avec p<0,05. Malheureusement, ces 5 groupes ont des taux de fracture élévés de 80 à 100% suite à la décimentation des boîtiers. Conclusion : Toutes les combinaisons de traitement de surface testées offrent une force d’adhésion cliniquement suffisante pour accomplir les mouvements dentaires en orthodontie. Une application de silane suivie d’un apprêt est forte intéressante, car elle est simple à appliquer cliniquement tout en permettant une excellente adhésion. Il faut cependant avertir les patients qu’il y a un risque de fracture des restorations en céramique lorsque vient le moment d’enlever les broches. Si la priorité est de diminuer le risque d’endommager la porcelaine, un mordançage seul à l’acide hydrofluorique sera suffisant.

Learning and Adjustment Outcomes in Socialized and Unsocialized Newcomers : An Ex- Post-Facto Comparative Study

Les restructurations et les mutations de plus en plus nombreuses dans les entreprises font évoluer la trajectoire de carrière des employés vers un cheminement moins linéaire et amènent une multiplication des changements de rôle (Delobbe & Vandenberghe, 2000). Les organisations doivent de plus en plus se soucier de l’intégration de ces nouveaux employés afin de leur transmettre les éléments fondamentaux du fonctionnement et de la culture qu’elles privilégient. Par contre, la plupart des recherches sur la socialisation organisationnelle portent sur les « meilleures pratiques », et les résultats qui en découlent sont mixtes. Cette étude comparative cherche à déterminer si et sur quelles variables les nouveaux employés socialisés par leur entreprise diffèrent des nouveaux employés « non socialisés ». Premièrement, cette étude vise à comparer ces deux groupes sur 1) les résultantes proximales (la maîtrise du contenu de la socialisation organisationnelle et la clarté de rôle) et 2) les résultantes distales (l’engagement organisationnel affectif, la satisfaction au travail et l’intention de quitter) du processus de socialisation organisationnelle, ainsi que sur 3) les caractéristiques des réseaux sociaux d’information, en contrôlant pour la proactivité. Dans un second temps, cette étude a pour objectif d’explorer si le processus de socialisation organisationnelle (les relations entre les variables) diffère entre les nouveaux employés socialisés ou non. Cinquante-trois nouveaux employés (moins d’un an d’ancienneté) d’une grande entreprise québécoise ont participé à cette étude. L’entreprise a un programme de socialisation en place, mais son exécution est laissée à la discrétion de chaque département, créant deux catégories de nouveaux employés : ceux qui ont été socialisés par leur département, et ceux qui n’ont pas été socialisés (« non socialisés »). Les participants ont été sondés sur les stratégies proactives, les résultantes proximales et distales et les caractéristiques des réseaux sociaux d’information. Pour le premier objectif, les résultats indiquent que les nouveaux employés socialisés maîtrisent mieux le contenu de la socialisation organisationnelle que les nouveaux employés non socialisés. En ce qui a trait au deuxième objectif, des différences dans le processus de socialisation organisationnelle ont été trouvées. Pour les nouveaux employés « non socialisés », la recherche proactive d’informations et la recherche de rétroaction sont liées à certaines caractéristiques des réseaux sociaux, alors que le cadrage positif est lié à la satisfaction au travail et à l’intention de quitter, et que la clarté de rôle est liée uniquement à la satisfaction au travail. Les nouveaux employés socialisés, quant à eux, démontrent des liens entre la maîtrise du contenu de la socialisation organisationnelle et chacune des résultantes distales (l’engagement organisationnel affectif, la satisfaction au travail et l’intention de quitter). Globalement, l’intégration des nouveaux employés non socialisés serait plutôt influencée par leurs stratégies proactives, tandis que celle des nouveaux employés non socialisés serait facilitée par leur maîtrise du contenu de la socialisation organisationnelle. De façon générale, cette étude comparative offre un aperçu intéressant des nouveaux employés rarement trouvé dans les recherches portant sur les « meilleures pratiques » de la socialisation organisationnelle. Des recommandations pour la recherche et la pratique en suivent.

Strength Predictions of Hat Stiffened Plate

Hat Stiffened Plates are used in composite ships and are gaining popularity in metallic ship construction due to its high strength-to-weight ratio. Light weight structures will result in greater payload, higher speeds, reduced fuel consumption and environmental emissions. Numerical Investigations have been carried out using the commercial Finite Element software ANSYS 12 to substantiate the high strength-to-weight ratio of Hat Stiffened Plates over other open section stiffeners which are commonly used in ship building. Analysis of stiffened plate has always been a matter of concern for the structural engineers since it has been rather difficult to quantify the actual load sharing between stiffeners and plating. Finite Element Method has been accepted as an efficient tool for the analysis of stiffened plated structure. Best results using the Finite Element Method for the analysis of thin plated structures are obtained when both the stiffeners and the plate are modeled using thin plate elements having six degrees of freedom per node. However, one serious problem encountered with this design and analysis process is that the generation of the finite element models for a complex configuration is time consuming and laborious. In order to overcome these difficulties two different methods viz., Orthotropic Plate Model and Superelement for Hat Stiffened Plate have been suggested in the present work. In the Orthotropic Plate Model geometric orthotropy is converted to material orthotropy i.e., the stiffeners are smeared and they vanish from the field of analysis and the structure can be analysed using any commercial Finite Element software which has orthotropic elements in its element library. The Orthotropic Plate Model developed has predicted deflection, stress and linear buckling load with sufficiently good accuracy in the case of all four edges simply supported boundary condition. Whereas, in the case of two edges fixed and other two edges simply supported boundary condition even though the stress has been predicted with good accuracy there has been large variation in the deflection predicted. This variation in the deflection predicted is because, for the Orthotropic Plate Model the rigidity is uniform throughout the plate whereas in the actual Hat Stiffened Plate the rigidity along the line of attachment of the stiffeners to the plate is large as compared to the unsupported portion of the plate. The Superelement technique is a method of treating a portion of the structure as if it were a single element even though it is made up of many individual elements. The Superelement has predicted the deflection and in-plane stress of Hat Stiffened Plate with sufficiently good accuracy for different boundary conditions. Formulation of Superelement for composite Hat Stiffened Plate has also been presented in the thesis. The capability of Orthotropic Plate Model and Superelement to handle typical boundary conditions and characteristic loads in a ship structure has been demonstrated through numerical investigations.

Soft Computing Approach for Optimization of siRNA Efficiency Prediction for Post-transcriptional Gene Silencing

Post-transcriptional gene silencing by RNA interference is mediated by small interfering RNA called siRNA. This gene silencing mechanism can be exploited therapeutically to a wide variety of disease-associated targets, especially in AIDS, neurodegenerative diseases, cholesterol and cancer on mice with the hope of extending these approaches to treat humans. Over the recent past, a significant amount of work has been undertaken to understand the gene silencing mediated by exogenous siRNA. The design of efficient exogenous siRNA sequences is challenging because of many issues related to siRNA. While designing efficient siRNA, target mRNAs must be selected such that their corresponding siRNAs are likely to be efficient against that target and unlikely to accidentally silence other transcripts due to sequence similarity. So before doing gene silencing by siRNAs, it is essential to analyze their off-target effects in addition to their inhibition efficiency against a particular target. Hence designing exogenous siRNA with good knock-down efficiency and target specificity is an area of concern to be addressed. Some methods have been developed already by considering both inhibition efficiency and off-target possibility of siRNA against agene. Out of these methods, only a few have achieved good inhibition efficiency, specificity and sensitivity. The main focus of this thesis is to develop computational methods to optimize the efficiency of siRNA in terms of “inhibition capacity and off-target possibility” against target mRNAs with improved efficacy, which may be useful in the area of gene silencing and drug design for tumor development. This study aims to investigate the currently available siRNA prediction approaches and to devise a better computational approach to tackle the problem of siRNA efficacy by inhibition capacity and off-target possibility. The strength and limitations of the available approaches are investigated and taken into consideration for making improved solution. Thus the approaches proposed in this study extend some of the good scoring previous state of the art techniques by incorporating machine learning and statistical approaches and thermodynamic features like whole stacking energy to improve the prediction accuracy, inhibition efficiency, sensitivity and specificity. Here, we propose one Support Vector Machine (SVM) model, and two Artificial Neural Network (ANN) models for siRNA efficiency prediction. In SVM model, the classification property is used to classify whether the siRNA is efficient or inefficient in silencing a target gene. The first ANNmodel, named siRNA Designer, is used for optimizing the inhibition efficiency of siRNA against target genes. The second ANN model, named Optimized siRNA Designer, OpsiD, produces efficient siRNAs with high inhibition efficiency to degrade target genes with improved sensitivity-specificity, and identifies the off-target knockdown possibility of siRNA against non-target genes. The models are trained and tested against a large data set of siRNA sequences. The validations are conducted using Pearson Correlation Coefficient, Mathews Correlation Coefficient, Receiver Operating Characteristic analysis, Accuracy of prediction, Sensitivity and Specificity. It is found that the approach, OpsiD, is capable of predicting the inhibition capacity of siRNA against a target mRNA with improved results over the state of the art techniques. Also we are able to understand the influence of whole stacking energy on efficiency of siRNA. The model is further improved by including the ability to identify the “off-target possibility” of predicted siRNA on non-target genes. Thus the proposed model, OpsiD, can predict optimized siRNA by considering both “inhibition efficiency on target genes and off-target possibility on non-target genes”, with improved inhibition efficiency, specificity and sensitivity. Since we have taken efforts to optimize the siRNA efficacy in terms of “inhibition efficiency and offtarget possibility”, we hope that the risk of “off-target effect” while doing gene silencing in various bioinformatics fields can be overcome to a great extent. These findings may provide new insights into cancer diagnosis, prognosis and therapy by gene silencing. The approach may be found useful for designing exogenous siRNA for therapeutic applications and gene silencing techniques in different areas of bioinformatics.

Effect of blood contamination on the shear bond strength at resin/dentin interface in primary teeth

Purpose: To assess in vitro the shear bond strength at the resin/dentin interface in primary teeth after contamination with fresh human blood. Methods: 75 crowns of primary molars were embedded in acrylic resin and mechanically ground to expose a flat dentin surface. The specimens were randomly assigned to five groups (n=15), according to the surface treatment. Group I (control) had no blood contamination. The other groups were blood-contaminated and subjected to different post-contamination protocols: in Group 2, the surfaces were rinsed with water; in Group 3, the surfaces were air-dried; in Group 4, the surfaces were rinsed and air-dried; and in Group 5, no post-contamination treatment was done. In all groups, a 3-mm dentin bonding site was demarcated, Single Bond adhesive system was applied and resin composite cylinders were bonded. After 24 hours in distilled water, shear bond strength was tested at a crosshead speed of 0.5 mm/minute. Results: Means (in MPa) were: Group 1: 7.1 (+/- 4.2); Group 2: 4.0 (+/- 1.8); Group 3: 0.9 (+/- 0.7); Group 4: 3.9 (+/- 2.2) and Group 5: 1.3 (+/- 1.5). Data were analyzed statistically by the Kruskal-Wallis test at 5% significance level. Groups 2 and 4 were similar to each other (P > 0.05) and both ware similar to Group 1 (P > 0.05). These groups (2, 3 and 4) had statistically significantly higher bond strengths than Groups 3 and 5 (P < 0.05). Blood contamination negatively affected the shear bond strength to primary tooth dentin. Among the blood-contaminated groups, water-rinsed specimens had higher bond strengths than those that were exclusively air-dried or not submitted to any post-contamination protocol before adhesive application.

Bond strength of fibre glass and carbon fibre posts to the root canal walls using different resin cements

The aim of the study was to evaluate the bond strength of fibre glass and carbon fibre posts in the root canal walls cemented with self-adhesive (RelyX-Unicem) and chemical (Cement-Post) resin cements. Forty maxillary canines were divided into four groups according to the cement and post used and submitted to the push-out test (0.5 mm min(-1)). The data were submitted to statistical analysis (2-way ANOVA, Bonferroni - P < 0.05) and fracture analysis by Scanning Electronic Microscopy. Fibre glass presented the best results when cemented with RelyX-Unicem and Cement-Post (P < 0.05). RelyX-Unicem presented the highest bond strength values for both posts (P < 0.05). Fracture analysis showed predominance of cohesive fracture of post for RelyX-Unicem and adhesive fracture between dentin/cement and mixed for Cement-Post. The bond strength values were significantly affected by the type of post and cement used and the highest values were found for fibre glass posts and RelyX-Unicem.

Influence of Post and Resin Cement on Stress Distribution of Maxillary Central Incisors Restored with Direct Resin Composite

The current study evaluated the influence of two endodontic post systems and the elastic modulus and film thickness of resin cement on stress distribution in a maxillary central incisor (MCI) restored with direct resin composite using finite element analysis (FEA). A three-dimensional model of an MCI with a coronary fracture and supporting structures was performed. A static chewing pressure of 2.16 N/mm(2) was applied to two areas on the palatal surface of the composite restoration. Zirconia ceramic (ZC) and glass fiber (GF) posts were considered. The stress distribution was analyzed in the post, dentin and cement layer when ZC and GF posts were fixed to the root canals using resin cements of different elastic moduli (7.0 and 18.6 GPa) and different layer thicknesses (70 and 200 mu m). The different post materials presented a significant influence on stress distribution with lesser stress concentration when using the GF post. The higher elastic modulus cement created higher stress levels within itself. The cement thicknesses did not present significant changes.