Comparação da viabilidade técnica-econômica em condicionamento de ar: compressor a pistão versus compressor rotativo de velocidade variável

Pós-graduação em Engenharia Mecânica - FEG

Aplicação de redes NeuroFuzzy ao processamento de peças automotivas por meio de injeção de polímeros

The injection molding of automotive parts is a complex process due to the many non-linear and multivariable phenomena that occur simultaneously. Commercial software applications exist for modeling the parameters of polymer injection but can be prohibitively expensive. It is possible to identify these parameters analytically, but applying classical theories of transport phenomena requires accurate information about the injection machine, product geometry, and process parameters. However, neurofuzzy networks, which achieve a synergy by combining the learning capabilities of an artificial neural network with a fuzzy set's inference mechanism, have shown success in this field. The purpose of this paper was to use a multilayer perceptron artificial neural network and a radial basis function artificial neural network combined with fuzzy sets to produce an inference mechanism that could predict injection mold cycle times. The results confirmed neurofuzzy networks as an effective alternative to solving such problems.

Ajuste do modelo QUAL2K e simulação de cenários para o Ribeirão Claro

The project has as objective to adjust the model QUAL2K to “Ribeirão Claro” river to evaluate the behavior of OD and DBO when are simulated the following sceneries: (i) implantation of a hypothetic wastewater station treatment that treats all the effluent thrown nowadays in the body of water; (ii) increase of withdrawal flow of DAAE to public supply and (iii) increase of nowadays flow of wastewater throwing, being the two last caused for the population increasing. The results obtained allowed to conclude that the model QUAL2K presented a good adjustment to the variable OD and a reasonable adjustment to the variable DBO, being that the same was suitable to the simulation of the sceneries proposed.

Uma análise da eficiência de uma transmissão CVT

This undergraduate thesis evaluates the effects of temperature variation of the air inside the CVT gearbox on the performance of a Continuously Variable Transmission (CVT). The CVT used in the tests was manufactured by Gaged Engineering (GX9 model) and is currently used in a Baja prototype. It’s a mechanically operated CVT, which the movement of the pulley plates varies according to the drive shaft rotation, shifting the belt along the diameter, and varying the transmission ratio. The purpose of this work is to analyze the change in the slip factor, coefficient that compares the variation between the actual transmission ratio and the ratio of geometric transmission, and its correlation with the power variation. A test bench was built and some tests were performed, indicating that was possible to achieve output power ratios of 1.75 [ℎ

Reproduction and recruitment of the seabob shrimp: a threatened exploitation species in southeastern of Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Improvement to the physical quality and imbibition pattern in seeds of candeia (Eremanthus incanus (Less.) Less.)

The objective of this work was to develop a methodology for seed processing and X-ray analysis and to study imbibition pattern in seeds of candeia (Eremanthus incanus). Seeds were gathered in 2001 and 2002 in Morro do Pilar and Lavras respectively, processed and stored in a cold chamber (5ºC/60%RH) until the start of experiments. In order to identify unfilled seeds, a protocol was developed for X-ray use combining radiation energy (Kv) and exposure time (seconds). For elimination of unfilled seeds, an experiment was conducted using a South Dakota seed blower whereby different opening settings and ventilation times were combined. Original seed lots and categorized lots following radiograph viewing were tested by germination tests, with seeds being cleansed in sodium hypochlorite and scattered over blotting paper in 'gerboxes' and then taken to germinators with alternating temperatures of 20º-30ºC and 10 hours of light, for up to 15 days. Imbibition curves were determined under the conditions 30ºC, 20º-30ºC/10 hours of light and 30º-20ºC/10 hours of light. The X-ray protocol that best allowed viewing of internal seed structures was 30Kv for 45 seconds. Seed separation using the blower setting at a 3.0 opening for 30 seconds raised the number of embryonic seeds to values exceeding 99%, also raising the germination rates as a consequence. The imbibition pattern is three-phased and the germination process is completed in 72 hours. Under alternate temperatures, primary root growth is favored.

Avaliação do desempenho de gotejadores com uso de água residual na suinocultura

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Desempenho de sondas Lambda no monitoramento de motores do ciclo Otto alimentados por etanol e GNV

Pós-graduação em Engenharia Mecânica - FEB

Cardiovascular risk in Japanese-Brazilian subjects

Objective: To evaluate the prevalence of risk factors for cardiovascular disease in Japanese-Brazilian subjects. Subjects and methods: One hundred thirty-one residents of the Mombuca community were studied. Statistical analysis was based on the X-2 test, Fisher's Exact test, Student's t test, and ANOVA, at a 5% significance level. Results: The average age was 56.7 years-old; 76.3% had dyslipidemia, 24.4% pre-diabetes (PDM), 10.7% type 2 diabetes mellitus (T2DM), 46.6% hypertension, 52.7% abdominal obesity, and 35.8% metabolic syndrome (MS). There were significant correlations between HOMA-IR and MS diagnosis and obesity, while HOMA-beta levels were decreased in T2DM and PDM. The ankle-brachial index was positive for peripheral artery disease in 22.3% of the individuals. Electrocardiograms did not show increased evidence of myocardial ischemia. Conclusion: Subjects of this community are exposed to major cardiovascular risk factors, namely high prevalence of MS diagnoses and increased HOMA-IR. Arq Bras Endocrinol Metab. 2012; 56(9): 608-13

Association study between functional polymorphisms in the TNF-alpha gene and obsessive-compulsive disorder

Obsessive-compulsive disorder (OCD) is a prevalent psychiatric disorder of unknown etiology. However, there is some evidence that the immune system may play an important role in its pathogenesis. In the present study, two polymorphisms (rs1800795 and rs361525) in the promoter region of the cytokine tumor necrosis factor-alpha (TNFA) gene were genotyped in 183 OCD patients and in 249 healthy controls. The statistical tests were performed using the PLINK (R) software. We found that the A allele of the TNFA rs361525 polymorphism was significantly associated with OCD subjects, according to the allelic x association test (p=0.007). The presence of genetic markers, such as inflammatory cytokines genes linked to OCD, may represent additional evidence supporting the rote of the immune system in its pathogenesis.

Viability of recently harvested and stored Xylopia aromatica (Lam.) Mart. (Annonaceae) seeds

Xylopia aromatica is a native species from Brazil's "Cerrado", recommended for restoration ecology and also as a medicine. Its seeds have embryos with morphophysiological dormancy, making nursery propagation difficult. The objective of this study was to verify the efficiency of X-ray and tetrazolium tests for evaluating the viability of three seed lots, stored for different periods. All seeds were X-rayed (13 kV, 350 seconds) and samples used for tetrazolium and germination tests. In the tetrazolium test, seeds were submitted to six treatments at two temperatures (25 and 30 °C) with imbibition in distilled water and immersion in three concentrations of tetrazolium solution (0.5, 0.75 and 1%) at the two imbibition temperatures. Seeds for the germination test were placed for imbibition in distilled water and a 500 ppm Promalin® (6-Benzyladenine + GA4 + GA7) solution and later sown in sterilized sand. The embryo could not be observed with the X-ray test. However, those seeds observed with an undamaged endosperm did not differ in the percentages of seeds with firm and stained endosperms observed in the tetrazolium test for all the lots. The tetrazolium test is efficient for evaluating seed viability, principally if imbibed at 30 °C and immersed in a 0.5% solution at 30 °C.

Applications of High Speed Configurable Logic Devices in Modern Particle Physics Experiments

Several activities were conducted during my PhD activity. For the NEMO experiment a collaboration between the INFN/University groups of Catania and Bologna led to the development and production of a mixed signal acquisition board for the Nemo Km3 telescope. The research concerned the feasibility study for a different acquisition technique quite far from that adopted in the NEMO Phase 1 telescope. The DAQ board that we realized exploits the LIRA06 front-end chip for the analog acquisition of anodic an dynodic sources of a PMT (Photo-Multiplier Tube). The low-power analog acquisition allows to sample contemporaneously multiple channels of the PMT at different gain factors in order to increase the signal response linearity over a wider dynamic range. Also the auto triggering and self-event-classification features help to improve the acquisition performance and the knowledge on the neutrino event. A fully functional interface towards the first level data concentrator, the Floor Control Module, has been integrated as well on the board, and a specific firmware has been realized to comply with the present communication protocols. This stage of the project foresees the use of an FPGA, a high speed configurable device, to provide the board with a flexible digital logic control core. After the validation of the whole front-end architecture this feature would be probably integrated in a common mixed-signal ASIC (Application Specific Integrated Circuit). The volatile nature of the configuration memory of the FPGA implied the integration of a flash ISP (In System Programming) memory and a smart architecture for a safe remote reconfiguration of it. All the integrated features of the board have been tested. At the Catania laboratory the behavior of the LIRA chip has been investigated in the digital environment of the DAQ board and we succeeded in driving the acquisition with the FPGA. The PMT pulses generated with an arbitrary waveform generator were correctly triggered and acquired by the analog chip, and successively they were digitized by the on board ADC under the supervision of the FPGA. For the communication towards the data concentrator a test bench has been realized in Bologna where, thanks to a lending of the Roma University and INFN, a full readout chain equivalent to that present in the NEMO phase-1 was installed. These tests showed a good behavior of the digital electronic that was able to receive and to execute command imparted by the PC console and to answer back with a reply. The remotely configurable logic behaved well too and demonstrated, at least in principle, the validity of this technique. A new prototype board is now under development at the Catania laboratory as an evolution of the one described above. This board is going to be deployed within the NEMO Phase-2 tower in one of its floors dedicated to new front-end proposals. This board will integrate a new analog acquisition chip called SAS (Smart Auto-triggering Sampler) introducing thus a new analog front-end but inheriting most of the digital logic present in the current DAQ board discussed in this thesis. For what concern the activity on high-resolution vertex detectors, I worked within the SLIM5 collaboration for the characterization of a MAPS (Monolithic Active Pixel Sensor) device called APSEL-4D. The mentioned chip is a matrix of 4096 active pixel sensors with deep N-well implantations meant for charge collection and to shield the analog electronics from digital noise. The chip integrates the full-custom sensors matrix and the sparsifification/readout logic realized with standard-cells in STM CMOS technology 130 nm. For the chip characterization a test-beam has been set up on the 12 GeV PS (Proton Synchrotron) line facility at CERN of Geneva (CH). The collaboration prepared a silicon strip telescope and a DAQ system (hardware and software) for data acquisition and control of the telescope that allowed to store about 90 million events in 7 equivalent days of live-time of the beam. My activities concerned basically the realization of a firmware interface towards and from the MAPS chip in order to integrate it on the general DAQ system. Thereafter I worked on the DAQ software to implement on it a proper Slow Control interface of the APSEL4D. Several APSEL4D chips with different thinning have been tested during the test beam. Those with 100 and 300 um presented an overall efficiency of about 90% imparting a threshold of 450 electrons. The test-beam allowed to estimate also the resolution of the pixel sensor providing good results consistent with the pitch/sqrt(12) formula. The MAPS intrinsic resolution has been extracted from the width of the residual plot taking into account the multiple scattering effect.

Laser guide stars wavefront sensors for the EELT

The Adaptive Optics is the measurement and correction in real time of the wavefront aberration of the star light caused by the atmospheric turbulence, that limits the angular resolution of ground based telescopes and thus their capabilities to deep explore faint and crowded astronomical objects. The lack of natural stars enough bright to be used as reference sources for the Adaptive Optics, over a relevant fraction of the sky, led to the introduction of artificial reference stars. The so-called Laser Guide Stars are produced by exciting the Sodium atoms in a layer laying at 90km of altitude, by a powerful laser beam projected toward the sky. The possibility to turn on a reference star close to the scientific targets of interest has the drawback in an increased difficulty in the wavefront measuring, mainly due to the time instability of the Sodium layer density. These issues are increased with the telescope diameter. In view of the construction of the 42m diameter European Extremely Large Telescope a detailed investigation of the achievable performances of Adaptive Optics becomes mandatory to exploit its unique angular resolution . The goal of this Thesis was to present a complete description of a laboratory Prototype development simulating a Shack-Hartmann wavefront sensor using Laser Guide Stars as references, in the expected conditions for a 42m telescope. From the conceptual design, through the opto-mechanical design, to the Assembly, Integration and Test, all the phases of the Prototype construction are explained. The tests carried out shown the reliability of the images produced by the Prototype that agreed with the numerical simulations. For this reason some possible upgrades regarding the opto-mechanical design are presented, to extend the system functionalities and let the Prototype become a more complete test bench to simulate the performances and drive the future Adaptive Optics modules design.

Chemical transformations of the pyrene K-region for functional materials

In dieser Arbeit wurde eine neue Methode zur asymmetrischen Substitution der K-Regionen von Pyren entwickelt, auf welcher das Design und die Synthese von neuartigen, Pyren-basierten funktionalen Materialien beruht. Eine Vielzahl von Substitutionsmustern konnte erfolgreich realisiert werden um die Eigenschaften entsprechend dem Verwendungszweck anzupassen. Der polyzyklische aromatische Kohlenwasserstoff (PAK) Pyren setzt sich aus vier Benzolringen in Form einer planaren Raute mit zwei gegenüberliegenden K-Regionen zusammen. Der synthetische Schlüsselschritt dieser Arbeit ist die chemische Transformation der einen K-Region zu einem α-Diketon und der darauffolgenden selektiven Bromierung der zweiten K-Region. Dieser asymmetrisch funktionalisierte Baustein zeichnet sich durch zwei funktionelle Gruppen mit orthogonaler Reaktivität aus und erweitert dadurch das Arsenal der etablierten Pyren Chemie um eine vielseitig einsetzbare Methode. Aufbauend auf diesem synthetischen Zugang wurden fünf wesentliche Konzepte auf dem Weg zu neuen, von Pyren abgeleiteten Materialen verfolgt: (i) Asymmterische Substitution mit elektronenziehenden versus -schiebenden Gruppen. (ii) Darstellung von Pyrenocyaninen durch Anbindung von Pyren mit einer der K-Regionen an das Phthalocyanin Gerüst zur Ausdehnung des π-Systems. (iii) Einführung von Thiophen an die K-Region um halbleitende Eigenschaften zu erhalten. (iv) Symmetrische Annullierung von PAKs wie Benzodithiophen und Phenanthren an beide K Regionen für cove-reiche und dadurch nicht-planare Strukturen. (v) Verwendung des K-Region-funktionalisierten Pyrens als Synthesebaustein für das Peri-Pentacen. Neben der Synthese wurde die Selbstorganisation in der Festphase und an der flüssig/fest Grenzfläche mittels zweidimensionaler Weitwinkel-Röntgenstreuung (2D WAXS) bzw. Rastertunnelmikroskopie (STM) untersucht. Die halbleitenden Eigenschaften wurden in organischen Feld-Effekt Transistoren (OFETs) charakterisiert.

Synthese von polymergebundenen Sialyl-Lewis x-Strukturen und deren Mimetika als Zelladhäsionsinhibitoren für E-, L- und P-Selektin

Kohlenhydrate dienen nicht nur der Ernährung oder der Stabilisierung von Zellwänden, sondern sie sind auch von essentieller Bedeutung für Zell-Zell-Wechselwirkungen im Organismus. Damit sind sie von besonderem Interesse für die Behandlung von Entzündungen sowie tumorösen Erkrankungen, die auf Wechselwirkungen zwischen bestimmten Kohlenhydraten und Rezeptoren, Selektine genannt, basieren. Die vorliegende Dissertation mit dem Titel „Synthese von polymergebundenen Sialyl-Lewis x-Strukturen und deren Mimetika als Zelladhäsionsinhibitoren für E-, L- und P-Selektin“ befasst sich mit der Synthese und der Modifizierung des natürlich vorkommenden Selektin-Liganden Sialyl-Lewisx und seinen potentiell mimetischen Strukturen auf Basis von Gemischen der an der Bindung beteiligten Kohlenhydrate sowie von sulfatierten Einheiten. Um im Organismus eine verstärkte Bindung an die zu adressierenden Rezeptoren und eine erhöhte Zirkulationsdauer zu erreichen, wurden die geeignet funktionalisierten Liganden mittels reaktiver Polymere auf Basis von Pentafluorphenyl-Reaktivestern im Rahmen einer polymeranalogen Umsetzung an ein definiertes Methacrylamid-Polymer gebunden.Um die biologische Wirksamkeit der synthetisierten Polymere zu überprüfen, wurden Oberflächenplasmonenresonanz-Messungen (SPR-Messungen) durchgeführt. Dabei zeigte sich bei den verschiedenen Selektinen eine unterschiedlich hohe Affinität der Sialyl-Lewis x sowie der mimetischen Polymere. Es konnten bei E-Selektin die geringsten, bei L-Selektin mittlere und bei P-Selektin die höchsten Affinitäten im unteren nanomolaren Bereich festgestellt werden.