Solvent-Resistant Polymeric Sensors for Adulteration Detection in Liquid Fuels

Polymeric sensors with improved resistance to organic solvents were produced via the layer-by-layer thin film deposition followed by chemical cross-linking. According to UV-vis spectroscopy, the mass loss of polyaniline/poly(vinyl alcohol) and polyaniline/novolac-type resin based films deposited onto glass slides was less than 20% when they were submitted to successive immersions (up to 3,000 immersion cycles) into commercially available ethanol and gasoline fuel samples. Polyallylamine hydrochloride/nickel tetrasulfonated phthalocyanine films presented similar stability. The electrical responses assessed by impedance spectroscopy of films deposited onto Au-interdigitated microelectrodes were relatively unaffected after continuous or cyclic immersions into both fuels. After these studies, an array including these polymeric sensors was employed to detect adulteration in ethanol and gasoline samples. After principal component analysis, it was possible to conclude that the proposed sensor array is capable to discriminate with remarkable reproducibility ethanol samples containing different amounts of water or else gasoline samples containing different amounts of ethanol. In both examples, more than 90% of data variance was retained in the first principal component. For each type of sample, ethanol and gasoline, it was found a linear correlation between one of the principal components and the sample's composition. These findings allow one to conclude that these films present great potential for the development of reliable and low-cost sensors for fuel analysis in liquid phase.

An electrochemical gas sensor based on paper supported room temperature ionic liquids

A sensitive and fast-responding membrane-free amperometric gas sensor is described, consisting of a small filter paper foil soaked with a room temperature ionic liquid (RTIL), upon which three electrodes are screen printed with carbon ink, using a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs as well as their easy immobilization into a porous and inexpensive supporting material such as paper. Moreover, thanks to a careful control of the preparation procedure, a very close contact between the RTIL and electrode material can be achieved so as to allow gaseous analytes to undergo charge transfer just as soon as they reach the three-phase sites where the electrode material, paper supported RTIL and gas phase meet. Thus, the adverse effect on recorded currents of slow steps such as analyte diffusion and dissolution in a solvent is avoided. To evaluate the performance of this device, it was used as a wall-jet amperometric detector for flow injection analysis of 1-butanethiol vapours, adopted as the model gaseous analyte, present in headspace samples in equilibrium with aqueous solutions at controlled concentrations. With this purpose, the RTIL soaked paper electrochemical detector (RTIL-PED) was assembled by using 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl) imide as the wicking RTIL and printing the working electrode with carbon ink doped with cobalt(II) phthalocyanine, to profit from its ability to electrocatalyze thiol oxidation. The results obtained were quite satisfactory (detection limit: 0.5 mu M; dynamic range: 2-200 mu M, both referring to solution concentrations; correlation coefficient: 0.998; repeatability: +/- 7% RSD; long-term stability: 9%), thus suggesting the possible use of this device for manifold applications.

Study of singlet excited state absorption spectrum of lutetium bisphthalocyanine using the femtosecond Z-scan technique

In this study we investigate the singlet excited state absorption of lutetium bisphthalocyanine (LuPc2) over a wide spectral range. It was observed distinct nonlinear absorption behaviors; saturable (SA) and reverse saturable absorption (RSA). The RSA effect was observed below 640 and above 680 nm, while SA occurs around the Q-band region, located around 660 nm. To describe the main singlet-singlet transitions, we employed the rate equation model considering the simplified three-energy level diagram. Our results reveal a ratio between excited and ground state absorption smaller than 0.05 at the Q-band region, and of approximately 4 for the other regions. (C) 2012 Elsevier B.V. All rights reserved.

Theoretical Study of the Absorption Spectra of Photosynthetic Pigments

The first stage of the photosynthetic process is the extraordinary efficiency of sunlight absorption in the visible region [1]. This region corresponds to the maximum of the spectral radiance of the solar emission. The efficient absorption of visible light is one of the most important characteristics of photosynthetic pigments. In chlorophylls, for example, the absorptions are seen as a strong absorption in the region 400-450 nm in connection with other absorptions with small intensities in the region of 500-600 nm. This work aims at understanding the essential features of the absorption spectrum of photosynthetic pigments, in line with several theoretical studies in the literature [2, 3]. The absorption spectra were calculated for H2-Porphyrin, Mg-Porphyrin, and Zn-Porphyrin, and for H2-Phthalocyanine and Mg-Phthalocyanine with and without the four peripheral eugenol substituents. The geometries were optimized using the B3LYP/6-31+G(d) theoretical model. For the calculation of the absorption spectra different TD-DFT calculations were performed (B3LYP, CAM-B3LYP, O3LYP, M06-2X and BP86) along with CIS (D). For the spectra the basis set 6-311++G (d, p) was used for porphyrins and 6-31+G (d) was used for the other systems. At this stage the solvent effects were considered using the simplified continuum model (PCM). First a comparison between the results using the different methods was made. For the porphyrins the best results compared to experiment (both in position and intensities) are obtained with M06-2X and CIS (D). We also analyze the compatibility of the four-orbital model of Gouterman [4] that states that transitions could be well described by the HOMO-1, HOMO, LUMO, and LUMO+1 molecular orbitals. Our results for H2-Porphyrin shows an agreement with other theoretical results and experimental data [5]. For the phthalocyanines (including the four peripheral eugenol substituents) the results are also in good agreement compared with the experimental results given in ref [6]. Finally, the results show that the inclusion of solvent eÆects gives corrections for the spectral shift in the correct direction but numerically small. References [1] R.E. Blankenship; “Molecular Mechanisms of Photosynthesis", Blackwell Science (2002). [2] P. Jaramillo, K. Coutinho, B.J.C. Cabral and S. Canuto; Chem. Phys. Lett., 516, 250(2011). [3] L. Petit, A. Quartarolo, C. Adamo and N. Russo; J. Phys. Chem. B, 110, 2398(2006). [4] M. J. Gouterman; Mol. Spectr., 6, 138(1961). [5] M. Palummo, C. Hogan, F. Sottile, P. Bagal∂a and A. Rubio; J. Chem. Phys., 131, 084102(2009). [6] E. Agar, S. Sasmaz and A. Agar; Turk. J. Chem., 23, 131(1999).

Determinazione di amminotioli mediante elettroforesi capillare

The aminothiols are critical cellular components that play numerous and important roles in metabolism as key extracellular reducing agents, critical substrates for proteins synthesis and detoxificants of free radicals and peroxides. Because altered thiols levels in body fluids are linked to specific pathological conditions, their measurement is thus considered very important. One method to determine these compounds is the capillary electrophoresis, a technique that involves the separation of charged molecules on the basis of their movement under the influence of an applied electric field. The instrument used in this work is equipped with an amperometric detector recording the current of the thiols oxidized at the end of the capillary at a BDD electrode. The aim of this work is to find a valid method for the separations of the aminothiols analyzed, in terms of capillary coating and experimental conditions. In order to find an alternative and less expensive electrode than BDD and to increase sensitivity for the detection of the thiols, a modified electrode consisting in a carbon paste electrode containing Cobalt-phthalocyanine has been studied. In this electrode Cobalt-phthalocyanine works as electrocatalyst to enhance the oxidation reaction, meanwhile the graphite acts as conductive mean. This kind of electrode shows great sensibility and low detection limits for the thiols that have a free thiolic group, but it is not sensible to disulfides. The analysis of human plasma point out that the best method found for the capillary electrophoresis is not useful for the detection of aminothiols in a healthy person, because the very low concentrations in which they are present.

Supramolecular order and dynamics of functional materials studied by solid state NMR

The goal of this thesis was the investigation of the structure, conformation, supramolecular order and molecular dynamics of different classes of functional materials (phthalocyanine, perylene and hexa-peri-hexabenzocoronene derivatives and mixtures of those), all having planar aromatic cores modified with various types of alkyl chains. The planar aromatic systems are known to stack in the solid and the liquid-crystalline state due to p-p interactions forming columnar superstructures with high one-dimensional charge carrier mobility and potential application in photovoltaic devices. The different functionalities attached to the aromatic cores significantly influence the behavior of these systems allowing the experimentalists to modify the structures to fine-tune the desired thermotropic properties or charge carrier mobility. The aim of the presented studies was to understand the interplay between the driving forces causing self-assembly by relating the structural and dynamic information about the investigated systems. The supramolecular organization is investigated by applying 1H solid state NMR recoupling techniques. The results are related with DSC and X-ray scattering data. Detailed information about the site-specific molecular dynamics is gained by recording spinning sideband patterns using 1H-1H and 13C-1H solid state NMR recoupling techniques. The determined dipole-dipole coupling constants are then related with the coupling constants of the respective rigid pairs, thus providing local dynamic order parameters for the respective moieties. The investigations presented reveal that in the crystalline state the preferred arrangement in the columnar stack of discotic molecules modified with alkyl chains is tilted. This leads to characteristic differences in the 1H chemical shifts of otherwise chemically equivalent protons. Introducing branches and increasing the length of the alkyl chains results in lower mesophase transitions and disordered columnar stacks. In the liquid-crystalline state some of the discs lose the tilted orientation, others do not, but all start a rapid rotation about the columnar axis.

13C NMR of a single molecule magnet: analysis of pseudocontact shifts and residual dipolar couplings

Paramagnetic triple decker complexes of lanthanides are promising Single Molecule Magnets (SMMs), with many potential uses. Some of them show preferable relaxation behavior, which enables the recording of well resolved NMR spectra. These axially symmetric complexes are also strongly magnetically anisotropic, and this property can be described with the axial component of the magnetic susceptibility tensor, χa. For triple decker complexes with phthalocyanine based ligands, the Fermi˗contact contribution is small. Hence, together with the axial symmetry, the experimental chemical shifts in 1H and 13C NMR spectra can be modeled easily by considering pseudocontact and orbital shifts alone. This results in the determination of the χa value, which is also responsible for molecular alignment and consequently for the observation of residual dipolar couplings (RDCs). A detailed analysis of the experimental 1H-13C and 1H-1H couplings revealed that contributions from RDCs (positive and negative) and from dynamic frequency shifts (negative for all observed couplings) have to be considered. Whilst the pseudocontact shifts depend on the average positions of 1H and 13C nuclei relative to the lanthanide ions, the RDCs are related to the mobility of nuclei they correspond to. This phenomenon allows for the measurement of the internal mobility of the various groups in the SMMs.

Solid-state NMR on columnar supramolecular structures

The present work deals with the characterisation of three columnar self-assembled systems, that is, benzene-1,3,5-tricarboxamides, a peripherally thioalkyl-substituted phthalocyanine, and several oligo-(p-phenylenevinylene)s. In order to probe the supramolecular organisation solid-state NMR has been used as the main technique, supported by X-ray measurements, theoretical methods, and thermal analysis. rnrnBenzene-1,3,5-tricarboxamides (BTAs) turned out to be well suited model compounds to study various fundamental supramolecular interactions, such as π-π-interactions, hydrogen bonding, as well as dynamic and steric effects of attached side chains. Six BTAs have been investigated in total, five with a CO-centred amide group bearing different side chains and one with an inverted N-centred amide group. The physical properties of these BTAs have been investigated as a function of temperature. The results indicated that in case of the CO-centred BTAs the stability of the columnar mesophase depends strongly on the nature of the side chains. Further experiments revealed a coplanar orientation of adjacent BTA molecules in the columnar assembly of CO-centred BTAs, whereas the N-centred BTA, showed a deviating not fully coplanar arrangement. These differences were ascribed to distinct hydrogen bonding schemes, involving a parallel alignment of hydrogen bonds in case of CO-centred BTAs and an antiparallel alignment in case of the N-centred counterpart.rnrn The fundamental insights of the supramolecular organisation of BTAs could be partially adapted to an octa-substituted phthalocyanine with thiododecyl moieties. Solid-state NMR in combination with chemical shift calculations determined a tilted herringbone arrangement of phthalocyanine rings in the crystalline phase as well as in the mesophase. Moreover, 1H NMR measurements in the mesophase of this compound suggested an axial rotation of molecules, which is inhibited in the crystalline phase.rnrnAs a third task, the supramolecular assembly of oligo-(p-phenylenevinylene)s of varying length and with different polar head groups have been investigated by a combined X-ray and solid-state NMR study. The results revealed a columnar structure formation of these compounds, being promoted by phase separation of alkyl side chains and aromatic rigid rods. In this system solid-state NMR yielded meaningful insight into the isotropisation process of butoxy and 2-S-methylbutoxy substituted oligo-(p-phenylenevinylene) rods.rn

Spinpolarisierte Rastertunnelmikroskopie magnetischer Nanostrukturen am Beispiel von bcc-Co/Fe(110), Fe/Mo(110) und Kupfer-Phthalocyanin/Fe(110)

In dieser Arbeit werden, nach einer Einführung in die spinpolarisierte Rastertunnelmikroskopie und -spektroskopie als experimentelle Methode zur Untersuchung magnetischer Nanostrukturen, Ergebnisse zur spinpolarisierten elektronischen Struktur in Abhängigkeit von der Kristallstruktur am Beispiel ultradünner Co-Schichten sowie in Abhängigkeit von der Magnetisierungsrichtung für ultradünne Fe-Schichten vorgestellt. Hochaufgelöste Messungen zeigen die ortsabhängige Spinpolarisation auf einem einzelnen Kupfer-Phthalocyanin Molekül. rnrnKobalt wurde durch pseudomorphes Wachstum auf den (110)-Oberflächen der kubisch raumzentrierten Metalle Chrom und Eisen deponiert. Im Unterschied zu früheren Berichten in der Literatur lassen sich nur zwei Lagen Co in der kubisch raumzentrierten (bcc) Ordnung stabilisieren. Die bcc-Co Schichten auf der Fe(110)-Oberfläche zeigen keine Anzeichen von epitaktischen Verzerrungen. rnDickere Schichten rekonstruieren in eine dicht gepackte Struktur (hcp/fcc). Durch die bcc Ordnung wird die Spinpolarisation von Kobalt auf P=62% erhöht (hcp-Co: P=45%). rnrnDie temperaturabhängige Spinreorientierung (SRT) ultradünner Filme Fe/Mo(110) wurde mit spinpolarisierter Spektroskopie untersucht. Eine Neuausrichtung der Magnetisierung aus der senkrechten [110]-Achse in die in der Ebene liegenden [001]-Achse wird bei T=(13,2+-0,5)K festgestellt, wobei es sich um einen diskontinuierlichen Reorientierungsübergang handelt, d.h. die freie Energie weist innerhalb eines bestimmten Temperaturbereichs gleichzeitig zwei Minima auf. Weiterhin wird in der Mono- und Doppellage Fe/Mo(110 eine Abhängigkeit der elektronischen Struktur von der Ausrichtung der magnetisch leichten Achse und von der Magnetisierung beobachtet. rnrnDie Untersuchung des spinpolarisierten Ladungstransports durch ein Kupfer-Phthalocyanin-Molekül auf der Fe/Mo(110) Oberfläche liefert einen wesentlichen Beitrag zum Verständnis des Spintransports an der Grenzfläche zwischen Metall und organischem Molekül. Die HOMO-LUMO-Energielücke des freien Moleküls wird durch die Wechselwirkung mit der Metalloberfläche mit Grenzflächenzuständen gefüllt. Diese Zustände reduzieren die Spinpolarisation des durch das Molekül fließenden Tunnelstroms durch einen zusätzlichen unpolarisierten Strombeitrag um einen Faktor zwei. Spinpolarisierte hybridisierte Grenzflächenzustände mit größerem Abstand zur Fermi-Energie führen in Abhängigkeit von der Position auf dem Molekül zu weiteren Beiträgen zur effektiven Spinpolarisation. Diese Untersuchungen belegen die Möglichkeit einer effektiven Spininjektion in organische Halbleiter und damit das Potential dieser Materialien für die weitere Entwicklung von Spintronik-Bauteilen.

Chemical transformations of the pyrene K-region for functional materials

In dieser Arbeit wurde eine neue Methode zur asymmetrischen Substitution der K-Regionen von Pyren entwickelt, auf welcher das Design und die Synthese von neuartigen, Pyren-basierten funktionalen Materialien beruht. Eine Vielzahl von Substitutionsmustern konnte erfolgreich realisiert werden um die Eigenschaften entsprechend dem Verwendungszweck anzupassen. Der polyzyklische aromatische Kohlenwasserstoff (PAK) Pyren setzt sich aus vier Benzolringen in Form einer planaren Raute mit zwei gegenüberliegenden K-Regionen zusammen. Der synthetische Schlüsselschritt dieser Arbeit ist die chemische Transformation der einen K-Region zu einem α-Diketon und der darauffolgenden selektiven Bromierung der zweiten K-Region. Dieser asymmetrisch funktionalisierte Baustein zeichnet sich durch zwei funktionelle Gruppen mit orthogonaler Reaktivität aus und erweitert dadurch das Arsenal der etablierten Pyren Chemie um eine vielseitig einsetzbare Methode. Aufbauend auf diesem synthetischen Zugang wurden fünf wesentliche Konzepte auf dem Weg zu neuen, von Pyren abgeleiteten Materialen verfolgt: (i) Asymmterische Substitution mit elektronenziehenden versus -schiebenden Gruppen. (ii) Darstellung von Pyrenocyaninen durch Anbindung von Pyren mit einer der K-Regionen an das Phthalocyanin Gerüst zur Ausdehnung des π-Systems. (iii) Einführung von Thiophen an die K-Region um halbleitende Eigenschaften zu erhalten. (iv) Symmetrische Annullierung von PAKs wie Benzodithiophen und Phenanthren an beide K Regionen für cove-reiche und dadurch nicht-planare Strukturen. (v) Verwendung des K-Region-funktionalisierten Pyrens als Synthesebaustein für das Peri-Pentacen. Neben der Synthese wurde die Selbstorganisation in der Festphase und an der flüssig/fest Grenzfläche mittels zweidimensionaler Weitwinkel-Röntgenstreuung (2D WAXS) bzw. Rastertunnelmikroskopie (STM) untersucht. Die halbleitenden Eigenschaften wurden in organischen Feld-Effekt Transistoren (OFETs) charakterisiert.

Photodynamic therapy results in induction of WAF1/CIP1/P21 leading to cell cycle arrest and apoptosis

Photodynamic therapy (PDT) is a promising new modality that utilizes a combination of a photosensitizing chemical and visible light for the management of a variety of solid malignancies. The mechanism of PDT-mediated cell killing is not well defined. We investigated the involvement of cell cycle regulatory events during silicon phthalocyanine (Pc4)-PDT-mediated apoptosis in human epidermoid carcinoma cells A431. PDT resulted in apoptosis, inhibition of cell growth, and G0-G1 phase arrest of the cell cycle, in a time-dependent fashion. Western blot analysis revealed that PDT results in an induction of the cyclin kinase inhibitor WAF1/CIP1/p21, and a down-regulation of cyclin D1 and cyclin E, and their catalytic subunits cyclin-dependent kinase (cdk) 2 and cdk6. The treatment also resulted in a decrease in kinase activities associated with all the cdks and cyclins examined. PDT also resulted in (i) an increase in the binding of cyclin D1 and cdk6 toward WAF1/CIP1/p21, and (ii) a decrease in the binding of cyclin D1 toward cdk2 and cdk6. The binding of cyclin E and cdk2 toward WAF1/CIP1/p21, and of cyclin E toward cdk2 did not change by the treatment. These data suggest that PDT-mediated induction of WAF1/CIP1/p21 results in an imposition of artificial checkpoint at G1 → S transition thereby resulting in an arrest of cells in G0-G1 phase of the cell cycle through inhibition in the cdk2, cdk6, cyclin D1, and cyclin E. We suggest that this arrest is an irreversible process and the cells, unable to repair the damages, ultimately undergo apoptosis.

A cyclodextrin dimer with a photocleavable linker as a possible carrier for the photosensitizer in photodynamic tumor therapy

A cyclodextrin dimer has been synthesized with two β-cyclodextrins linked by a flexible chain containing a carbon–carbon double bond. This dimer binds and solubilizes a phthalocyanine-based photosensitizer that generates singlet oxygen on irradiation. When the complex is irradiated, the singlet oxygen cleaves the carbon–carbon link, and the cyclodextrins are released, liberating the photosensitizer into the light path. Ideas about how this phenomenon could be used to make photodynamic tumor therapy into a more selective process are described.

Nanopartículas lipídicas sólidas e vesículas cataniônicas contendo ftalocianina de cloro alumínio aplicadas nos processos fotodinâmicos

O trabalho apresentado foi realizado em duas etapas independentes e baseou-se no estudo de diferentes sistemas nanométricos para viabilizar a aplicação da ftalocianina de cloro alumínio (ClAlPc) na terapia fotodinâmica (TFD) para o tratamento do câncer de pele do tipo melanoma. O fármaco fotossensibilizante (FS) utilizado apresenta propriedades físico-químicas que lhe permitem exercer sua atividade fotodinâmica com excelência, sem a interferência do cromóforo endógeno melanina existente nas células melanocíticas. Para driblar sua elevada hidrofobicidade, ClAlPc foi encapsulada em sistemas nanométricos para administração em meio fisiológico. Inicialmente nanopartículas lipídicas sólidas (NLS) foram desenvolvidas por emulsificação direta, após um estudo de elaboração do diagrama de fases. O compritol foi o lipídio sólido escolhido para compor as NLS, com diferentes concentrações de ClAlPc. Todas as formulações desenvolvidas foram devidamente caracterizadas, com tamanho médio entre 100 e 200 nm, baixa polidispersão, potencial zeta adequadamente negativo (~|30| mV), drug loading de ClAlPc entre 76-94% (com pequena redução após 24 meses) e alta eficiência de encapsulação (E.E.). A morfologia arredondada das nanopartículas foi confirmada por microscopia eletrônica de transmissão e de força atômica. A estabilidade das NLS foi de 24 meses. A avaliação da cristalinidade do lipídio revelou a integração da ClAlPc à matriz lipídica da NLS, presença de estruturas polimórficas e grau de cristalinidade adequado, sem alterações após 24 meses. Nos estudos de difusão in vitro, observou-se que ftalocianina encapsulada nas NLS acumulam-se preferencialmente na epiderme e derme do que no estrato córneo, sem traços de permeação do ativo. Foi confirmado o caráter biocompatível das NLS sobre fibroblastos NIH-3T3. A ftalocianina encapsulada nas NLS não foi tóxica na linhagem de melanoma B16-F10 na ausência de luz, porém, apresentou excelente efeito fototóxico (0,75 ?g mL-1 de ClAlPc nanoencapsulada e irradiação entre 0,5 e 2,0 J cm-2), com redução da viabilidade celular de 87%. O segundo sistema de veiculação estudado foram as vesículas cataniônicas (VesCat), que se formam espontaneamente em água com o tensoativo TriCat 12. A obtenção das vesículas contendo ClAlPc envolve uma etapa adicional, para remoção de solvente orgânico, que foi aprimorada, reduzindo o tempo de produção em 55%. As VesCat/ClAlPc obtidas mantiveram suas propriedades físico-químicas e morfologia arredondada (confirmada por microscopia eletrônica de varredura), drug loading de 47% e alta E.E. Os resultados comprovaram que a aplicação desses dois sistemas nanométricos é altamente eficiente para aplicação da TFD no tratamento do câncer de pele do tipo melanoma ou outras doenças cutâneas, apresentando características favoráveis para avanços nos estudos de fase clínica e pré-clínica.

Preparação, caracterização e propriedades de lipossomas contendo o ácido -ciano-4-hidroxicinâmico e o agente fotossenbilizador AICIPc: um novo sistema carreador específico com ação sinérgica aplicado a terapia fotodinâmica

Ftalocianina de alumínio-cloro (AlClPc) é um fotossensibilizador de segunda geração em terapia fotodinâmica (TFD) caracterizado por seu caráter anfifílico e tendência de auto-agregação em meio aquoso, o que prejudica seu potencial de aplicação. O aCHC é um substrato de transportadores de monocarboxilato (MCT) superexpresso em células de MCF-7. Objetivando a solubilização da AlClPc e aumento de internalização em tecidos neoplásicos nos propomos aqui o uso de DSPC e DOPC em diferentes proporções para formar vesículas lipidicas mistas (LV) na presença de aCHC como sistemas veiculadores de fármaco. Lv foi preparado pelo método de injeção etanólica e formou vesículas de dimensões nanométricas (aproximadamente 100 nm) com bom índice de polidispersão, valores negativos de potencial zeta e estáveis em meio aquoso por mais de 50 dias. AlClPc se complexou com o fosfato das LV o que conferiu uma localização interfacial às moléculas de AlClPc como demonstrado pelos resultados de supressão de fluorescência. Medidas de anisotropia, fluorescência estática e resolvida no tempo corroboram com estes resultados e demonstram que a auto-agregação da AlClPc ocorre mesmo em lipossomas. Entretanto, a veiculação da AlClPc por LV em carcinoma de células escamosas oral (OSCC) levou a um processo de desagregação demonstrado por (FLIM). Este incrível comportamento é novo e aumenta o conhecimento científico sobre o mecanismo intracelular de ação de fotossensibilizadores em TFD. Em TFD, ambos os sistemas LVIII+AlClPc e LVIII+AlClPc+aCHC não apresentaram toxicidade no escuro no período de incubação de 3 h com as concentrações de lipídios, AlClPc e aCHC iguais a 0,15 mmol/L, 0,5 umol/L e 10,0 umol/L, respectivamente. De maneira inesperada, o sistema LVIII+AlClPc foi mais eficiente em TFD que o sistema LVIII+AlClPc+aCHC, devido ao caráter antioxidante do aCHC. Estes resultados abrem uma nova perspectiva do potencial uso de LV-AlClPc para o tratamento fotodinâmico.

Ação sinérgica entre terapia fotodinâmica e terapia hipertérmica utilizando nanobarras de ouro

Estudos com tratamento hipertérmico de tumores utilizando nanopartículas metálicas têm sido realizados durante as últimas décadas e mostram resultados bons quanto à remissão de tumores, por vezes chegando à cura completa. O mesmo acontece em relação aos tratamentos baseados em ação fotodinâmica de fotossensibilizadores. Tratamentos aliando a terapia hipertérmica com nanopartículas de ouro e a terapia fotodinâmica com diversos fotossensibilizadores tem efeito sinérgico e apresenta excelente potencial terapêutico, em que pese serem necessários mais estudos para que uma nova terapia conjunta possa ser implementada. A proposta deste trabalho foi investigar esse efeito sinérgico utilizando nanobastões de ouro complexados com fotossensibilizadores. Após a síntese dos nanobastões pelo método de seeding, a eficácia do tratamento fotodinâmico e da terapia hipertérmica, separadamente, foi investigada. A metodologia do recobrimento dos nanobastões por fotossensibilizador, em um primeiro momento, não logrou êxito com a porfirina, porém com a ftalocianina tetracarboxilada se mostrou mais eficaz. A taxa de fotodegradação da ftalocianina em solução foi investigada como parâmetro para a eficiência em geração de oxigênio singlete. Após centrifugação e lavagem das nanopartículas, no entanto, evidenciou-se por espectrofotometria que o fotossensibilizador não permaneceu aderido aos nanobastões. Em um segundo momento, optamos por recobrir os nanobastões por porfirinas tetrassulfonadas, com ou sem grupamentos metil-glucamina. Após o processo de recobrimento, essas ftalocianinas formaram complexos iônicos com o CTAB que recobre os nanobastões. Os complexos nanobastões-ftalocianinas foram analisados por microscopia eletrônica de transmissão e as taxas de geração de oxigênio singlete e de radical hidroxil foram investigadas. Além disso, foram utilizadas para testes in vivo e in vitro com células de melanoma melanótico (B16F10) ou amelanótico (B16G4F). As células tumorais em cultura ou os tumores em camundongos C57BL6 foram irradiados com luz em 635 nm e os tumores foram observados por 15 dias após o tratamento. Houve evidente aumento na geração de oxigênio singlete por ambos fotossensibilizadores, e maior geração de radicais livres por parte do fotossensibilizador metilglucaminado. O oposto ocorre com o fotossensibilizador sem metilglucamina. Houve, também, moderada citotoxicidade no escuro quando células foram incubadas com nanopartículas recobertas por ftalocianinas ou não. Quando ativados pela luz, os complexos ftalocianinas-nanobastões desencadearam um aumento de 5ºC no meio de cultura das células, e a morte celular observada foi extensa (91% para a linhagem B16G4F e 95% para a linhagem B16F10). Tanto os resultados in vitro quanto os in vivo indicam que as propriedades das ftalocianinas testadas são melhoradas significativamente quando elas estão complexadas aos nanobastões. Este é um estudo pioneiro por utilizar duas porfirinas tetrassulfonadas específicas e por utilizar o mesmo comprimento de onda para a ativação dos fotossensibilizadores e nanobastões.